diff options
Diffstat (limited to 'include/ps2mult.h')
| -rw-r--r-- | include/ps2mult.h | 150 |
1 files changed, 150 insertions, 0 deletions
diff --git a/include/ps2mult.h b/include/ps2mult.h new file mode 100644 index 00000000000..8da20fc4421 --- /dev/null +++ b/include/ps2mult.h @@ -0,0 +1,150 @@ +#ifndef __LINUX_PS2MULT_H +#define __LINUX_PS2MULT_H + +#define kbd_request_region() ps2mult_init() +#define kbd_request_irq(handler) ps2mult_request_irq(handler) + +#define kbd_read_input() ps2mult_read_input() +#define kbd_read_status() ps2mult_read_status() +#define kbd_write_output(val) ps2mult_write_output(val) +#define kbd_write_command(val) ps2mult_write_command(val) + +#define aux_request_irq(hand, dev_id) 0 +#define aux_free_irq(dev_id) + +#define PS2MULT_KB_SELECTOR 0xA0 +#define PS2MULT_MS_SELECTOR 0xA1 +#define PS2MULT_ESCAPE 0x7D +#define PS2MULT_BSYNC 0x7E +#define PS2MULT_SESSION_START 0x55 +#define PS2MULT_SESSION_END 0x56 + +#define PS2BUF_SIZE 512 /* power of 2, please */ + + /* PS/2 controller interface (include/asm/keyboard.h) + */ +extern int ps2mult_init (void); +extern int ps2mult_request_irq(void (*handler)(void *)); +extern u_char ps2mult_read_input(void); +extern u_char ps2mult_read_status(void); +extern void ps2mult_write_output(u_char val); +extern void ps2mult_write_command(u_char val); + +extern void ps2mult_callback (int in_cnt); + + /* Simple serial interface + */ +extern int ps2ser_init(void); +extern void ps2ser_putc(int chr); +extern int ps2ser_getc(void); +extern int ps2ser_check(void); + + + /* Serial related stuff + */ +struct serial_state { + int baud_base; + int irq; + u8 *iomem_base; +}; + +#define UART_RX 0 /* In: Receive buffer (DLAB=0) */ +#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */ +#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */ + +#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */ +#define UART_IER 1 /* Out: Interrupt Enable Register */ + +#define UART_IIR 2 /* In: Interrupt ID Register */ +#define UART_FCR 2 /* Out: FIFO Control Register */ + +#define UART_LCR 3 /* Out: Line Control Register */ +#define UART_MCR 4 /* Out: Modem Control Register */ +#define UART_LSR 5 /* In: Line Status Register */ +#define UART_MSR 6 /* In: Modem Status Register */ +#define UART_SCR 7 /* I/O: Scratch Register */ + +/* + * These are the definitions for the FIFO Control Register + * (16650 only) + */ +#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */ +#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ +#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ +#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ +#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ +#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ +#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ +#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ +#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ + +/* + * These are the definitions for the Line Control Register + * + * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting + * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits. + */ +#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ +#define UART_LCR_SBC 0x40 /* Set break control */ +#define UART_LCR_SPAR 0x20 /* Stick parity (?) */ +#define UART_LCR_EPAR 0x10 /* Even parity select */ +#define UART_LCR_PARITY 0x08 /* Parity Enable */ +#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */ +#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */ +#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */ +#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */ +#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ + +/* + * These are the definitions for the Line Status Register + */ +#define UART_LSR_TEMT 0x40 /* Transmitter empty */ +#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */ +#define UART_LSR_BI 0x10 /* Break interrupt indicator */ +#define UART_LSR_FE 0x08 /* Frame error indicator */ +#define UART_LSR_PE 0x04 /* Parity error indicator */ +#define UART_LSR_OE 0x02 /* Overrun error indicator */ +#define UART_LSR_DR 0x01 /* Receiver data ready */ + +/* + * These are the definitions for the Interrupt Identification Register + */ +#define UART_IIR_NO_INT 0x01 /* No interrupts pending */ +#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ + +#define UART_IIR_MSI 0x00 /* Modem status interrupt */ +#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ +#define UART_IIR_RDI 0x04 /* Receiver data interrupt */ +#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ + +/* + * These are the definitions for the Interrupt Enable Register + */ +#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ +#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ +#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ +#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ + +/* + * These are the definitions for the Modem Control Register + */ +#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ +#define UART_MCR_OUT2 0x08 /* Out2 complement */ +#define UART_MCR_OUT1 0x04 /* Out1 complement */ +#define UART_MCR_RTS 0x02 /* RTS complement */ +#define UART_MCR_DTR 0x01 /* DTR complement */ + +/* + * These are the definitions for the Modem Status Register + */ +#define UART_MSR_DCD 0x80 /* Data Carrier Detect */ +#define UART_MSR_RI 0x40 /* Ring Indicator */ +#define UART_MSR_DSR 0x20 /* Data Set Ready */ +#define UART_MSR_CTS 0x10 /* Clear to Send */ +#define UART_MSR_DDCD 0x08 /* Delta DCD */ +#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ +#define UART_MSR_DDSR 0x02 /* Delta DSR */ +#define UART_MSR_DCTS 0x01 /* Delta CTS */ +#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */ + +#endif /* __LINUX_PS2MULT_H */ |