summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-03-12Refactor linker-generated arraysAlbert ARIBAUD
Refactor linker-generated array code so that symbols which were previously linker-generated are now compiler- generated. This causes relocation records of type R_ARM_ABS32 to become R_ARM_RELATIVE, which makes code which uses LGA able to run before relocation as well as after. Note: this affects more than ARM targets, as linker- lists span possibly all target architectures, notably PowerPC. Conflicts: arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds arch/arm/cpu/armv7/omap-common/u-boot-spl.lds board/ait/cam_enc_4xx/u-boot-spl.lds board/davinci/da8xxevm/u-boot-spl-da850evm.lds board/davinci/da8xxevm/u-boot-spl-hawk.lds board/vpac270/u-boot-spl.lds Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-12arm: make __bss_start and __bss_end__ compiler-generatedAlbert ARIBAUD
Turn __bss_start and __bss_end__ from linker-generated to compiler-generated symbols, causing relocations for these symbols to change type, from R_ARM_ABS32 to R_ARM_RELATIVE. This should have no functional impact, as it affects references to __bss_start and __bss_end__ only before relocation, and no such references are done. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-12Remove linker lists (LGAs) from SPL linker scriptsAlbert ARIBAUD
Many SPL linker scripts needlessly include linker lists (aka LGAs). Remove them whenever possible; keep it only in the seven am335x_evm variants (am335x_evm, am335x_evm_uart[1-5], am335x_evm_spiboot), where there is actual content in output section .u_boot_list. This commit keeps all u-boot.bin and u-boot-spl.bin in ARM targets byte-identical. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-12arm: omap: map u_boot_lists section to .sramAlbert ARIBAUD
Output section .u_boot_list was left unmapped in u-boot-spl.lds for omap-common, causing the location counter to roll back to bteween .rodata and .data, making __image_copy_end and _end symbols wrong. Mapping output section .u_boot_list to memory .sram fixes these symbols' mapping. This modifies the SPL binary but has no functional impact, as __image_copy_end and _end are never used in SPLs and u_boot_list is empty for all 29 boards affected (omap4_sdp4430 eco5pk igep0030 am335x_evm_uart3 omap3_beagle am3517_crane igep0032 mt_ventoux pcm051 am3517_evm omap3_evm_quick_mmc am335x_evm_uart2 am335x_evm_spiboot am335x_evm_uart1 omap3_evm igep0030_nand omap3_overo igep0020 am335x_evm omap4_panda omap5_evm am335x_evm_uart4 devkit8000 tricorder mcx twister omap3_evm_quick_nand am335x_evm_uart5 igep0020_nand). Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-12Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-03-12ARM: sam9x5: fix ethernet pins in MII modeJesse Gilles
Fix pin setting in MII mode Signed-off-by: Jesse Gilles <jgilles@multitech.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-12ARM: at91sam9x5: Using CPU string directlyBo Shen
As the CPU name is not configurable, using CPU string directly Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-12ARM: at91: change nand flash tableBo Shen
Change nand flash partition table according to www.at91.com/linux4sam more information: http://www.at91.com/linux4sam/bin/view/Linux4SAM/GettingStarted#Linux4SAM_NandFlash_demo_Memory Signed-off-by: Bo Shen <voice.shen@atmel.com> [minor commit message changes] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-12arm: at91/configs: add bootz to configurationNicolas Ferre
Support to boot zImage Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> [Add bootz for at91rm9200, at91sam9263, at91sam9rl] Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-12arm: at91/configs: add libfdt to configurationNicolas Ferre
support to boot device tree Linux kernel Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> [Add libftd for at91rm9200, at91sam9263, at91sam9rl] Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-11Merge u-boot/master into u-boot-ti/masterTom Rini
In master we had already taken a patch to fix the davinci GPIO code for CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these conflicts manually and comment the #else/#endif lines for clarity. Conflicts: arch/arm/include/asm/arch-davinci/gpio.h drivers/gpio/da8xx_gpio.c Signed-off-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: Add silicon id support for DRA752 socLokesh Vutla
Adding CPU detection support for the DRA752 ES1.0 soc. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: Add dra7xx_evm build supportLokesh Vutla
Adding the build support for dra7xx_evm. Reusing omap5_evm.h config by moving it to omap5_common.h Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com>
2013-03-11arm: dra7xx: Add board files for DRA7XX socsLokesh Vutla
Adding new board files for DRA7XX socs. The pad registers layout is changed completely from OMAP5 So introducing the new structure here and also adding the minimal data. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishant Kamat <nskamat@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com> [trini: Adapt omap_mmc_init call for last 2 params] Signed-off-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: Add DDR related data for DRA752 ES1.0Lokesh Vutla
DRA752 uses DDR3. Populating the corresponding structures with DDR3 data. Writing into MA registers if only MA is present in that soc. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: Add control module changesLokesh Vutla
Control module register addresses are changed from OMAP5 to DRA7XX socs. So adding the necessary changes for the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: clock: Add the dplls dataLokesh Vutla
A new DPLL DDR is added in DRA7XX socs. Now clocks to EMIF CD is from DPLL DDR. So DPLL DDR should be locked before initializing RAM. Also adding other dpll data which are different from OMAP5 ES2.0. SYS_CLK running at 20MHz is introduced in DRA7xx socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: clock: Add the prcm changesLokesh Vutla
PRCM register addresses are changed from OMAP5 ES2.0 to DRA7XX. So adding the necessary register changes for DRA7XX socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com>
2013-03-11ARM: OMAP5: srcomp: enable slew rate compensation cells after powerupLokesh Vutla
After power-up SRCOMP cells are by-passed by default in OMAP5. Software has to enable these SRCOMP sells. For ES2: All 5 SRCOMP cells needs to be enabled. For ES1: Only 4 SRCOMP cells in core power domain are enabled. The 1 in wkup domain is not enabled because smart i/os of wkup domain work with default compensation code. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP5: Add DDR changes required for OMAP543X ES2.0 SOCsLokesh Vutla
Add pre calculated timing settings of LPDDR2 and DDR3 memories present in OMAP5430 and OMAP5432 ES2.0 versions. Also adding the DDR pad io settings required for OMAP543X SOCs here. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4/5: clocks: Add the required OPP settings as per the latest addendumSRICHARAN R
Change OPP settings as per the latest 0.5 version of addendum for OMAP5430 ES2.0. omap4/hw_data.c is touched here to add dummy dividers. While here correcting OPP_NOM mpu, core frequency for OMAP4430 ES2.x Note that OMAP5430 ES1.0 support is still kept alive and would be removed in a cleanup later. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Cc: Tom Rini <trini@ti.com> Cc: Nishanth Menon <nm@ti.com>
2013-03-11ARM: OMAP5: clock: Add the prcm register changes required for ES2.0SRICHARAN R
PRCM register addresses are changed from ES1.0 to ES2.0 due to PER power domain getting moved to CORE power domain. So adding the nessecary register changes for the same. Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP5: Add silicon id support for ES2.0 revision.SRICHARAN R
Adding the CPU detection suport for OMAP5430 and OMAP5432 ES2.0 SOCs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Cc: Tom Rini <trini@ti.com> Cc: Nishanth Menon <nm@ti.com>
2013-03-11ARM: OMAP5: Clean up iosettings codeLokesh Vutla
There is some code duplication in the ddr io settings code. This is avoided by moving the data to a Soc specific place and letting the code generic. This avoids unnessecary code addition for future socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4+: Make control module register structure genericLokesh Vutla
A seperate omap_sys_ctrl_regs structure is defined for omap4 & 5. If there is any change in control module for any of the ES versions, a new structure needs to be created. In order to remove this dependency, making the register structure generic for all the omap4+ boards. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4+: Cleanup emif specific filesLokesh Vutla
Removing the duplicated code in ddr3 initialization. Also creating structure for lpddr2 mode registers to avoid unnessecary revision checks. These change reduces code addition for future Socs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4+: Clean up the pmic codeSRICHARAN R
The pmic code is duplicated for OMAP 4 and 5. Instead move the data to Soc specific place and share the code. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4+: Cleanup the clocks layerSRICHARAN R
Currently there is quite a lot of code which is duplicated in the clocks code for OMAP 4 and 5 Socs. Avoiding this here by moving the clocks data to a SOC specific place and the sharing the common code. This helps in addition of a new Soc with minimal changes. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11ARM: OMAP4+: Change the PRCM structure prototype common for all SocsSRICHARAN R
The current PRCM structure prototype directly matches the hardware register layout. So there is a need to change this for every new silicon revision which has register space changes. Avoiding this by making the prototye generic and populating the register addresses seperately for all Socs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-03-11ARM: OMAP4+: emif: Detect SDRAM from SDRAM config registerLokesh Vutla
Now SDRAM initialization is done on the basis of omap revision. Instead this should be done on basis of SDRAM type read from EMIF_SDRAM_CONFIG register. This will be helpful to avoid unnessecary cpu checks for new boards Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11cm_t35: prevent splashimage from being set to a bad valueNikita Kiryanov
Define CONFIG_SPLASHIMAGE_GUARD to prevent splashimage from being set to a value that will cause U-Boot to hang while displaying a splash screen. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-11lcd: implement a callback for splashimageNikita Kiryanov
On some architectures certain values of splashimage will lead to a data abort exception. Document the problem, and implement a callback for splashimage to reject such values. Cc: Anatolij Gustschin <agust@denx.de> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-11am335x: cpsw: optimize cpsw_send to increase network performanceMugunthan V N
Before submitting packets to cpdma, phy status is updated on every packet which leads to delay in packet send intern reduces the Ethernet performance. Checking mdio status for each packet will reduce timetaken to send a packet and there by increasing the Ethernet performance. With this the performance is increased from 208KiB/s to 375KiB/s on EVMsk Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-03-11omap4_common: Enable CONFIG_CMD_BOOTZTom Rini
With v3.9 and later of the Linux Kernel defaulting to multi-platform images with omap2plus_defconfig, uImage isn't builtable anymore by default. Add CONFIG_CMD_BOOTZ so that we can still boot something the kernel spits out. Cc: Sricharan R <r.sricharan@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: R Sricharan <r.sricharan@ti.com>
2013-03-11omap3_beagle: Enable CONFIG_CMD_BOOTZTom Rini
With v3.9 and later of the Linux Kernel defaulting to multi-platform images with omap2plus_defconfig, uImage isn't builtable anymore by default. Add CONFIG_CMD_BOOTZ so that we can still boot something the kernel spits out. Signed-off-by: Tom Rini <trini@ti.com>
2013-03-11omap5_evm: Enable CONFIG_CMD_BOOTZTom Rini
With v3.9 and later of the Linux Kernel defaulting to multi-platform images with omap2plus_defconfig, uImage isn't builtable anymore by default. Add CONFIG_CMD_BOOTZ so that we can still boot something the kernel spits out. Cc: Sricharan R <r.sricharan@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: R Sricharan <r.sricharan@ti.com>
2013-03-11am335x_evm: Enable CONFIG_CMD_BOOTZTom Rini
With v3.9 and later of the Linux Kernel defaulting to multi-platform images with omap2plus_defconfig, uImage isn't builtable anymore by default. Add CONFIG_CMD_BOOTZ so that we can still boot something the kernel spits out. Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-11Allow AM33xx boards to setup GPMC chipselects.Mark Jackson
Expose the enable_gpmc_cs_config() function so AM33xx based boards can register GPMC chip selects. Changes in V4: - Fix checkpatch errors (TAB -> space mangling) Changes in V3: - Fix line wrapping Changes in V2: - Indicate this is for AM33xx (not OMAP2) Signed-off-by: Mark Jackson <mpfj@newflow.co.uk> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-11OMAP3: Initialize gpmc if SPL_ONENAND_SUPPORT is enabled.Enric Balletbo i Serra
In order to use SPL boot from OneNAND we should initialize the gpmc. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-03-11SPL: ONENAND: Support SPL to boot u-boot from OneNAND.Enric Balletbo i Serra
This patch will allow use SPL to boot an u-boot from the OneNAND. Tested with IGEPv2 board with a OneNAND from Numonyx Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> [trini: Add <spl.h> hunk to fix warning] Signed-off-by: Tom Rini <trini@ti.com>
2013-03-08SPL: ONENAND: Fix onenand_spl_load_image implementation.Enric Balletbo i Serra
Tested with an IGEPv2 board seems that current onenand_spl_load_image implementation doesn't work. This patch fixes this function changing the read loop and reading the onenand blocks from page to page. Tested with various IGEP based boards with a OneNAND from Numonyx. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-03-08SPL: ONENAND: Fix some ONENAND related defines.Enric Balletbo i Serra
Some ONENAND related defines use the term ONE_NAND instead of ONENAND, as the technology name is ONENAND this patch replaces all these defines. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-03-08cm-t35: add support for user defined lcd parametersNikita Kiryanov
Add support for user defined lcd parameters for cm-t35 splash screen. Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Anatolij Gustschin <agust@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08cm-t35: add support for dvi displaysNikita Kiryanov
Add support for dvi displays with user selectable dvi presets. Cc: Wolfgang Denk <wd@denx.de> Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Anatolij Gustschin <agust@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08lcd: add option for board specific splash screen preparationNikita Kiryanov
Currently there is no logical place to put the code that prepares the splash image data. The splash image data should be ready in memory before bmp_display() is called, and after the environment is ready (since lcd.c looks for the splash image in an address specified by the environment variable "splashimage"). Our window of opportunity in board_init_r() is therefore: between env_relocate() and bmp_display(), and from the available options only the lcd related functions in drv_lcd_init() seem appropriate for such lcd oriented code. Add the option to prepare the splash image data in lcd_logo() right before it is sent to be displayed. Cc: Anatolij Gustschin <agust@denx.de> Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08omap3: allow dynamic selection of gfx_formatNikita Kiryanov
Currently, omap3_dss_panel_config() sets gfx_format to a value that is hardcoded in the code. This forces anyone who wants to use a different gfx_format to make adjustments after calling omap3_dss_panel_config(). This could be avoided if the value of gfx_format were parameterized as input for omap3_dss_panel_config(). Make gfx_format a field in struct panel_config, and update existing structs to set this field to the value that was originally hard coded. Cc: Wolfgang Denk <wd@denx.de> Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08omap3: add useful dss definesNikita Kiryanov
Add useful omap3 dss defines for: polarity, TFT data lines, lcd display type, gfx burst size, and gfx format Cc: Anatolij Gustschin <agust@denx.de> Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08omap_hsmmc: add driver check for write protectionNikita Kiryanov
Add check for write protection in omap mmc driver. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-08mmc: add support for write protectionNikita Kiryanov
Add generic mmc write protection functionality. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08cm-t35: implement board specific card detect checkNikita Kiryanov
Implement a card detection check for cm-t35. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
generated by cgit v1.2.3 (git 2.0.4) at 2024-11-13 00:04:34 +0000