summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2021-03-03board: gateworks: imx8mm: Add Gateworks Venice board supportTim Harvey
Add initial support for Gateworks Venice product family based on the i.MX 8M Mini SoC Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-03-03arm: dts: imx8mm: add Gateworks i.MX8 Mini Dev kitsTim Harvey
Add Gateworks i.MX 8M Mini Development kits from Linux-5.12-rc1 Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-03-01ARM: imx: Include u-boot.img in u-boot-with-spl.imx if OF_SEPARATE=yMarek Vasut
The u-boot-with-spl.imx is a concatenation of SPL and u-boot.uim. The u-boot.uim is u-boot.bin wrapped in uImage. In case OF_SEPARATE is enabled, the u-boot.bin does not contain control DT for U-Boot, and so u-boot.uim does not contain the DT, and so u-boot-with-spl.imx does not contain the DT, and a system where u-boot-with-spl.imx is written to offset 1024B to the start of storage no longer boots, as it is missing DT. In case OF_SEPARATE is enabled, u-boot.img contains both u-boot.bin and the necessary DTs. Therefore, use u-boot.img instead of u-boot.uim to generate u-boot-with-spl.imx when OF_SEPARATE is enabled. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Christoph Niedermaier <cniedermaier@dh-electronics.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com>
2021-03-01ARM: imx: Do not hard-code MX8M MMU table DRAM entry offsetMarek Vasut
Instead of hard-coding the offset of DRAM entries in MMU table all over the code, auto-detect the offset. This removes error-prone code which would break e.g. in case the MMU table is modified. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-03-01ARM: dts: imx8mq-evk: Remove u-boot,off-on-delay-us propertyFabio Estevam
Commit 247bbeb74c18 ("ARM: dts: imx8m: increase off-on delay on the SD Vcc regulator") caused the imx8mq-evk board to not be able to store the environment variables in the SD card. Remove the u-boot,off-on-delay-us property to fix the regression. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
2021-03-01tools: imx8mimage: Restore the original __ALIGN_MASK() macroFabio Estevam
Since commit c738adb8dbbf ("tool: Move ALIGN_MASK to header as common MACRO") the i.MX8MQ EVK board no longer boots. The reason is that imx8mimage.c used a custom __ALIGN_MASK() macro, so restore the original macro to fix the boot and rename it accordingly. Reported-by: Lukas Rusak <lorusak@gmail.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Ye Li <ye.li@nxp.com>
2021-03-01arm: dts: imx8mp-evk: Add FEC PHY reset timingYe Li
Add phy-reset-duration and phy-reset-post-delay to FEC node for PHY reset, otherwise the PHY does not work correctly. Signed-off-by: Ye Li <ye.li@nxp.com>
2021-03-01imx: Add 2GB lpddr support for i.MX8MN Beacon EmbeddedWorks devkit.Adam Ford
There is a second lpddr configuration with 2GB of RAM, but this requires different RAM timings, so in addition to adding the timing file, a separate defconfig is necessary. Signed-off-by: Adam Ford <aford173@gmail.com>
2021-03-01doc: board: freescale: imx8mp_evk: update to newer versions and change ↵Peter Bergin
ATF_LOAD_ADDR Update imx-atf and firmware-imx to latest released versions. Update address of ATF_LOAD_ADDR that has changed to 0x970000 in imx-atf commit 48733cb4e773a7584ced601de9d717efa3d73815. Add 'O=' to make and build in separate directory as one issue has been noticed where it was trouble building directly inside u-boot source dir. Restructure the workflow and copy binaries after defconfig to ensure that build directory is created. Signed-off-by: Peter Bergin <peter@berginkonsult.se> Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
2021-03-01ARM: imx: Add missing FEC ethernet quirk for MX8MMarek Vasut
The MX8M also contains a gigabit MAC, so define FEC_QUIRK_ENET_MAC. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-03-01mx6sabre: Fix boot failureYe Li
CONFIG_SPL_LEGACY_IMAGE_SUPPORT is necessary for mx6sabresd and mx6sabreauto, because u-boot is packed as legacy image not FIT. However, this config is not set when CONFIG_SPL_LOAD_FIT is enabled. Must enable it explicitly, otherwise will fail to boot like below. U-Boot SPL 2021.04-rc2 (Feb 20 2021 - 16:43:04 -0800) Trying to boot from MMC1 mmc_load_image_raw_sector: mmc block read error SPL: failed to boot from all boot devices Signed-off-by: Ye Li <ye.li@nxp.com>
2021-03-01mmc: fsl_esdhc_imx: fix the DTOCV to 0xEHaibo Chen
On imx6Q/imx6DL, we find if config the DTOCV to 0~3, it will impact cmd6 behavior, after cmd6 get transfer complete interrupt, the data0 line will keep low over 5 seconds. This should be a IC bug on imx6Q/DL. For other platforms, do not has this issue. To fix this issue, fix the DTOCV to 0xE, the max setting, this also align with Linux configuration. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-03-01mx23evk: Add myself as maintainerFabio Estevam
I would like to help supporting this board, so add myself as a maintainer. Now that the board has been converted to DM, also add its devicetree in the MAINTAINERS files entry. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01mx23evk: Convert to driver modelFabio Estevam
Make the conversion to driver model as it is mandatory. Successfully tested booting Linux from the SD card. Dropped splash screen support as this needs to be properly converted to DM and tested. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01mx23-evk: Import devicetree file from LinuxFabio Estevam
Import the imx23-evk devicetree files from Linux kernel version 5.11. This is in preparation for converting the mx23evk_defconfig target to driver model. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01mx51evk: Add myself as maintainerFabio Estevam
I would like to help supporting this board, so add myself as a maintainer. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01mx51evk: Convert to driver modelFabio Estevam
Make the conversion to driver model as it is mandatory. Tested booting the Linux kernel from the SD card. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01imx51-babbage: Import devicetree files from LinuxFabio Estevam
Import the imx51-babbage devicetree files from Linux kernel version 5.11-rc7. This is in preparation for converting the mx51evk_defconfig target to driver model. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01mmc: fsl_esdhc_imx: Add a compatible for i.MX51Fabio Estevam
Add a compatible for i.MX51 so that i.MX51 can use this driver via driver model. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-03-01mx53loco: Add myself as maintainerFabio Estevam
I would like to help supporting this board, so add myself as a maintainer. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01ARM: dts: imx53-qsb: Describe the esdhc1 card detect pinFabio Estevam
The micro SD card slot uses GPIO3_13 as card detect pin, so describe it in the devicetree. This was noticed when converting imx53-qsb board to driver model in U-Boot as the micro SD card was not getting detected. After this change it is possible to load the dtb and zImage from the SD card and boot Linux. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01mx53loco: Convert to driver modelFabio Estevam
Make the conversion to driver model as it is mandatory. Remove the SATA support for now as the i.MX53 support has not been added yet. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01imx53-qsb: Import devicetree files from LinuxFabio Estevam
Import the imx53-qsb devicetree files from Linux kernel version 5.11-rc7. This is in preparation for converting the mx53loco_defconfig target to driver model. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01board: toradex: move RGMII delays to PHY sideOleksandr Suvorov
The RGMII link delays can be set on either MAC or PHY side. Set the rgmii-id PHY mode for FEC and remove FEC_ENET_ENABLE_.XC_DELAY setting, so that these definitions aren't used anymore throughout the U-Boot. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-03-01ARM: imx8: Add missing FEC ENET quirk for i.MX8/i.MX8XOleksandr Suvorov
Both NXP SoCs i.MX8 and i.MX8X have ENET gigabit MAC. Define FEC_QUIRK_ENET_MAC for the imx8 platform and remove this definition from configs of boards, based on MX8/MX8X. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Marek Vasut <marex@denx.de> Reviewed-By: Ramon Fried <rfried.dev@gmail.com> Acked-by: Oliver Graute <oliver.graute@kococonnector.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-03-01Respect that some compression algos can be enabled separately for SPLFrieder Schrempf
Some compression algorithms currently can be enabled for SPL and U-Boot proper separately. Therefore take into account USE_HOSTCC is well as CONFIG_IS_ENABLED() in these cases to prevent compiling these functions in case of a host tool build. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-03-01thermal: imx_tmu: enable monitoring and default alert/criticalTim Harvey
Set default critical/alert temperature and enabling monoitoring. Without calling imx_tmu_enable_msite() monitoring will not be enabled and read_temperature will return 0. Additionally without setting alert temperature will cause imx_tmu_get_temp() to spin indefiniately thinking the system needs to cool. This resolves the board spinning endlessly when enabling IMX_TMU in the SPL. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-03-01ARM: mx6: Add function to set serial#Sean Anderson
The serial number OTP is similar to the imx7 version, except that the register names are different. This also sets serial# directly, instead of providing board_get_serial. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2021-03-01ARM: imx6: mx6sabre-common: Search for boot components in /boot tooMarek Vasut
Some root filesystem configurations do not have separate /boot partition, but rather place kernel, DT, scripts into /boot directory. Search the /boot directory for these boot components in case they are not found in /, which is the old behavior. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2021-03-01ARM: imx6: mx6sabre-common: Replace fatload with FS_GENERIC loadMarek Vasut
Replace filesystem specific fatload command with a filesystem agnostic load command, so the board can boot from e.g. ext4 too. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2021-02-27ARM: imx6: dh-imx6: Drop the SF hunk in configMarek Vasut
There is now CONFIG_SPL_DM_SPI{,_FLASH}, however keeping CONFIG_DM_SPI{,_FLASH} enabled in SPL seems to grow the SPL by a couple of bytes: text data bss dec hex filename - 34069 1568 96 35733 8b95 spl/u-boot-spl + 34075 1568 96 35739 8b9b spl/u-boot-spl In either case, the binary is bootable, so remove the part in board config. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Ludwig Zenz <lzenz@dh-electronics.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@konsulko.com>
2021-02-27ARM: imx6: dh-imx6: Enable support for applying DTOMarek Vasut
Enable DTO support to make it possible to boot fitImage with DTOs embedded in them. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2021-02-27ARM: imx: Revert "dh_imx6: Switch to full DM-aware"Marek Vasut
This reverts commit 03a673cf49e ("dh_imx6: Switch to full DM-aware"). According to discussion [1], the patch is known to break the dh_imx6 board, however it made it upstream just before 2021.01-rc4, likely by mistake. Revert this patch to put the board back into working order. Also note that this board has no DM SPL support due to OCRAM size limitations, but that is fine, as SPL DM support is optional. [1] https://lists.denx.de/pipermail/u-boot/2020-June/417986.html Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Ludwig Zenz <lzenz@dh-electronics.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@konsulko.com>
2021-02-26Merge https://gitlab.denx.de/u-boot/custodians/u-boot-usbTom Rini
- fastboot updates / fixes
2021-02-26Merge https://gitlab.denx.de/u-boot/custodians/u-boot-spiTom Rini
- new GigaDevice flash ids - fixes for imx, nxp_spi drivers
2021-02-26Merge tag 'u-boot-stm32-20210226' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - Add USB host boot support in stm32mp1 config - Enable uefi related commands for STMicroelectronics STM32MP15 boards - Remove duplicate uart nodes in stm32mp15 device tree
2021-02-26configs: stm32mp1: enable uefi related commandsIlias Apalodimas
The board can boot with UEFI. With the latest changes in U-Boot's EFI subsystem we also have support for EFI runtime variables, without SetVariable support. We can also store the EFI variables in a file on the ESP partition and preserve them across reboots. The env and efidebug commands are missing in order to configure EFI variables and the efibootmgr though. Since U-Boot's default config enables other EFI related commands (e.g bootefi), let's add the env related and efidebug commands and allow users to do that Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-02-26arm: dts: stm32mp15: remove duplicate uart nodesPatrick Delaunay
Remove duplicated uart nodes introduced with commit 62f95af92a3f ("ARM: dts: stm32mp1: DT alignment with Linux kernel v5.9-rc4"), because the uart nodes wasn't correctly ordered in alphabetic order. Only cosmetic: the generated device tree don't change. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-02-26ARM: stm32: Add USB host boot supportMarek Vasut
Add support for booting from USB pen drive, since USB host port is available on the STM32MP1. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-02-26usb: gadget: dwc2_udc_otg: Fix dwc2_gadget_start() and ↵Patrice Chotard
usb_gadget_register_driver() Since commit 8745b9ebccae ("usb: gadget: add super speed support") ums was no more functional on platform which use dwc2_udc_otg driver. This was due to a too restrictive test which checked that the gadget driver speed was either FS or HS. So all gadget driver with max speed set to speed higher than HS (SS in case of composite gadget driver in our case) are not allowed, which is wrong. Update the speed test in usb_gadget_register_driver() and in dwc2_gadget_start() to allow all gadget driver speed equal or higher than FS. Tested on stm32mp157c-ev1 board. Fixes: c791c8431c34 ("usb: dwc2: convert driver to DM_USB_GADGET") Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-02-26usb: kbd: Also accept keyboards with Interrupt OUT endpointStefan Brüns
The OUT endpoint can just be ignored as it is not used, just as the corresponding Set_Report request for IN-only interfaces. E.g. the Linux gadget hid keyboard also provides an interrupt endpoint. Also cleanup confusing debug messages like "found set protocol", which is printed when a keyboard device is found, while the Set_Protocol request is issued quite some time later. Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
2021-02-26fastboot: add UUU command UCmd and ACmd supportHeiko Schocher
add support for the UUU commands ACmd and UCmd. Enable them through the Kconfig option CONFIG_FASTBOOT_UUU_SUPPORT base was commit in NXP kernel 9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support") and ported it to current mainline. Tested this patch on imx6ul based board. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-02-26doc: Document partition specificationsSean Anderson
This documents the way U-Boot understands partitions specifications. This also updates the fastboot documentation for the changes in the previous commit. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-26doc: Rename k210 partitions anchorSean Anderson
This anchor is only for the k210 partition layout, so rename it appropriately. This keeps it from conflicting with the (to be added) anchor for U-Boot partitions in general. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-26fastboot: Allow u-boot-style partitionsSean Anderson
This adds support for partitions of the form "dev.hwpart:part" and "dev#partname". This allows one to flash to eMMC boot partitions without having to use CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT. It also allows one to flash to an entire device without needing CONFIG_FASTBOOT_MMC_USER_NAME. Lastly, one can also flash MMC devices other than CONFIG_FASTBOOT_FLASH_MMC_DEV. Because devices can be specified explicitly, CONFIG_FASTBOOT_FLASH_MMC_DEV is used only when necessary for existing functionality. For those cases, fastboot_mmc_get_dev has been added as a helper function. This allows There should be no conflicts with the existing system, but just in case, I have ordered detection of these names after all existing names. The fastboot_mmc_part test has been updated for these new names. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-26fastboot: Move part_get_info_by_name_or_alias after raw_part_get_info_by_nameSean Anderson
This makes the next commit more readable by doing the move now. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-26fastboot: Remove mmcpart argument from raw_part_get_info_by_nameSean Anderson
The only thing mmcpart was used for was to pass to blk_dselect_hwpart. This calls blk_dselect_hwpart directly from raw_part_get_info_by_name. The error handling is dropped, but it is reintroduced in the next commit (albeit less specificly). Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-26part: Support string block devices in part_get_info_by_dev_and_nameSean Anderson
This adds support for things like "#partname" and "0.1#partname". The block device parsing is done like in blk_get_device_part_str. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-26part: Support getting whole disk from part_get_info_by_dev_and_name_or_numSean Anderson
This adds an option to part_get_info_by_dev_and_name_or_num to allow callers to specify whether whole-disk partitions are fine. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-26part: Give several functions more useful return valuesSean Anderson
Several functions in disk/part.c just return -1 on error. This makes them return different errnos for different failures. This helps callers differentiate between failures, even if they cannot read stdout. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.2.3 (git 2.0.4) at 2025-08-07 18:12:27 +0000