| Age | Commit message (Collapse) | Author |
|---|
|
https://source.denx.de/u-boot/custodians/u-boot-i2c
i2c updates for v2024.01-rc2
- nuvoton: support standard/fast/fast plus mode
- bootcount: remove legacy i2c driver and implement
DM based version
Bugfixes:
- designware_i2c: adjust timing calculation
SPL probing failed on the StarFive VisionFive 2 board
Heinrich fixed this, by syncing timing calculation with
linux implementation.
|
|
+ CI: Use OpenSBI 1.3.1 release for testing
+ riscv: Support resume after exception
+ rng: Support RNG provided by RISC-V Zkr ISA extension
+ board: starfive VF2: Support jtag
+ board: starfive VF2: Support TRNG driver
+ board: sifive unmatched: Move kernel load address
|
|
Enables JH7110 RNG driver to visionfive2 board.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Adds jh7110 trng device tree node.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Adds to support JH7110 TRNG driver which is based on linux kernel's
jh7110-trng.c. This can support to generate 256-bit random numbers and
128-bit but this makes 256-bit default for convenience.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Add STGCLK_SEC_HCLK and STGCLK_SEC_MISCAHB clocks for JH7110 TRNG
device.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
This imports mmio functions from Linux's arch/riscv/include/asm/mmio.h
to use read/write[b|w|l|q]_relaxed functions.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
The Zkr ISA extension (ratified Nov 2021) introduced the seed CSR. It
provides an interface to a physical entropy source.
A RNG driver based on the seed CSR is provided. It depends on
mseccfg.sseed being set in the SBI firmware.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
If CSRs like seed are readable by S-mode, may not be determinable by
S-mode. For safe driver probing allow to resume via a longjmp after an
exception.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
JTAG pins are mapped as below. To access the JTAG pins, we need to
control the GPIO pins from SPL which seems to be the earliest stage for
JTAG.
- JTAG nTRST: GPIO36 / Input
- JTAG TDI: GPIO61 / Input
- JTAG TMS: GPIO63 / Input
- JTAG TCK: GPIO60 / Input
- JTAG TDO: GPIO44 / Output
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Add gpio.h header file that includes JH7110 helper macros. The file is
imported from StarFive github[1] with small changes such as alignment.
[1]: https://github.com/starfive-tech/u-boot
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Some RISC-V CPUs, such as the T-HEAD XuanTie series, have a
vendor-specific way to invalidate a portion of the instruction cache.
Allow them to override invalidate_icache_range().
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
This is required on CPUs which always operate in CLIC mode, such as the
T-HEAD E906 and E907. Per the CLIC specification: "In this mode, the
trap vector base address held in mtvec is constrained to be aligned on a
64-byte or larger power-of-two boundary."
Reported-by: Madushan Nishantha <jlmadushan@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Clean things up for the next time somebody adds a target.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
U-boot initially loads the kernel image to the kernel_addr_r, and
subsequently relocates it to memory address 0x80200000. Setting
kernel_addr_r to 0x80200000 can eliminate one copy operation.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Use the most recent upstream release of OpenSBI for CI testing.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-clk
Clock changes for 2024.01-rc2
This contains several fixes for the clock core.
|
|
If the device does not specify any clocks in device tree, these
functions will return PTR_ERR(-ENOENT). This is not the intended
behavior and does not comply with linux kernel CCF. Fix that by
returning NULL under such circumstances instead.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230818-clk-fix-v1-3-49ec18f820bf@outlook.com
|
|
In clk_enable()/clk_disable() functions, when CCF is activated,
we must pass a private clk struct to enable()/disable() ops functions.
Otherwise, the use of a container_of() construction within these ops
should be banned. Because passing a non-private clk struct to
container_of() results in an out of range error.
At the moment, clk-mux, clk-fixed-factor, clk-gate and possibly other
clocks use container_of() in their enable()/disable() functions.
Therefore, for these functions to work correclty, private clk struct
must be passed.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230905221649.3577929-1-bigunclemax@gmail.com
|
|
The second parameter for clk_release_all is used as an unsigned
(which makes sense) but the function prototype declares it as an int.
This causes warnings/error like such below:
include/clk.h:422:48: error: conversion to ‘int’ from ‘unsigned int’ may change the sign of the result [-Werror=sign-conversion]
422 | return clk_release_all(bulk->clks, bulk->count);
To fix this, changed the type of the count to `unsigned int`
Fixes: 82a8a669b4f7 ("clk: add clk_release_all()")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230619104752.278500-1-eugen.hristev@collabora.com
|
|
In commit 5c5992cb90cf ("clk: Add debugging for return values"), a
temporary storage variable was added around the ops->get_rate() call
inside clk_get_rate(), so that the result could be passed through
log_ret.
This temporary variable was declared as an int, yet when we look in
struct clk_ops, we can see this needs to be a ulong:
ulong (*get_rate)(struct clk *clk);
This was resulting in a signed to unsigned casting error on our
builds, where a clock value of 0xABCDABCD was being incorrectly cast
to 0xFFFFFFFFABCDABCD.
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230515195005.1961495-1-nathan.morrison@timesys.com
|
|
- Four patches to address issues with bootstd flows in some cases
|
|
This has a typo which makes the method inoperable. Correct it so that
'bootflow read' works correctly for ChromeOS.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Two bugs have appeared:
- arguments can have an equals sign embedded in them, which must be
considered part of the value
- arguments must fully match the name; partial matches should be
ignored
Fix these and add a test to cover both.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Enable the bootflow based on this bootmeth if the BootOrder EFI
variable is set.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Compiling sandbox_defconfig with CONFIG_BOOTSTD=n fails:
/usr/bin/ld: drivers/mtd/spi/sf_bootdev.o:
in function `sf_get_bootflow':
/drivers/mtd/spi/sf_bootdev.c:43:(.text+0x96):
undefined reference to `bootmeth_set_bootflow'
Add the missing Kconfig dependency.
Fixes: Fixes: 0c1f4a9fb13a ("bootstd: Add a SPI flash bootdev")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
Add extension to the 'mmc' command to read out the card registers.
Currently, only the eMMC OCR/CID/CSD/EXTCSD/RCA/DSR register are
supported. A register value can either be displayed or read into
an environment variable.
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
As noted in commit 3a6383207be ("mmc: sdhci: add the quirk for broken
r1b response"), some MMC controllers don't always set the transfer
complete bit with R1b responses.
According to the SD Host Controller Simplified Specification v4.20,
> In the case of a command pairing with response-with-busy[, Transfer
> Complete] is set when busy is de-asserted. Refer to DAT Line Active
> and Command Inhibit (DAT) in the Present State register.
By polling the DAT Line Active bit in the present state register, we can
detect when we are no longer busy, without waiting for a long timeout.
This results in much faster reads/writes on buggy controllers.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Henrik Grimler <henrik@grimler.se>
|
|
dm_pci_map_bar() return a value of (void *) already, hence no need
to cast it again before assigning to host->ioaddr.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
mmc_bind() in mmc-uclass.c calls blk_create_devicef() which is
defined in blk-uclass.c, so SPL_BLK is required by SPL_DM_MMC.
Implicitly select SPL_BLK for SPL_DM_MMC.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
- Updates for npcm8xx, developerbox, corstone1000 and one clock fix for
TI K3 platforms.
|
|
enable PSCI reset used for the system reset
Even though Corstone-1000 does not implement the entire PSCI APIs,
it relies on PSCI reset interface for the system reset.
Signed-off-by: Emekcan Aras <emekcan.aras@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
|
|
enable distro_bootcmd
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
|
|
unzip the kernel before executing it
The Corstone-1000 kernel has become too large to fit in the available
storage. Switching to a compressed kernel avoids the problem, but
requires uncompressing it.
Changes made are generated using savedefconfig.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
|
|
Current documentation limits the firmware size to 1.5MB.
When the fTPM and StandaloneMM-based RPMB secure storage is
enabled, firmware size is bigger than that size.
Let's specify the A/B update bank size(4MB) for flash
rawwrite parameter.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
v2023.07 is the last version supporting old NOR flash layout
by default. The later versions of U-Boot, Developerbox is
configured to enable A/B update and new NOR Flash layout
by default.
This commit updates the documentation to pin the U-Boot
version for the old NOR flash layout. It is still useful
for the user wants to replace the factory default EDK II
firmware to U-Boot.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
There are two kinds of NOR flash layout for the Developerbox.
Capsule update for the old layout is no longer available since
it has small capacity for secure world images and can not
house the TA such as fTPM.
This commit removes the definition related to the obsolete
NOR flash layout for the UEFI capsule update.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
PLL calibration needs to be enabled when operating in non fractional
mode. Add the sequence to do a fast calibration when using PLL
in this mode.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
|
|
disable this config to improve flash program time
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
1. Fix incorrect ram size of 4GB dram with ECC enabled
2. Fix wrong place to set dram bank size
- The dram bank size should be set in dram_init_banksize
- Dram_init should not access gd->bd because the board info
struct is not reserved yet.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
[trini: Rework slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add uart baud rate table to arbel(npcm8xx) and poleg(npcm7xx)
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
[trini: Rework slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
GPIO function name is needed in the debug log
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
This adds a generic I2C bootcounter adhering to driver model to replace
the previously removed legacy implementation.
There is no change in functionality, it can be used on any I2C device.
The device tree configuration may look like this for example:
bootcount {
compatible = "u-boot,bootcount-i2c";
i2cbcdev = <&i2c_rtc>;
offset = <0x11>;
};
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This new function enhances the i2c_get_chip*() toolbox by implementing a
variant that does not require a chip_addr. Instead, the desired device
is pointed to by a phandle.
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
The legacy I2C bootcounter will hereby be removed and eventually
be replaced by a driver model implementation in the follow-up commit.
The legacy driver has the following drawbacks:
- It's not adhering to the driver model
- Settings are grabbed from Kconfig rather than device tree
- i2c_{read,write} are being used instead of dm_i2c_{read,write}
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
- Two Kconfig content fixes, fix some issues reported by Coverity,
resync get_maintainer.pl (two small fixees), update i2c_eeprom, and
fix an off by one in addrmap_set_entry
|
|
Calculate the maximum length of the buffer when writing
across the page boundary. If the buffer length (len)
exceeds the page boundary (pagesize), split it. Use this
length instead of comparing the length with the pagesize,
because if the write start address (offset) is not at the
beginning of a page and the page_offset + len is greater
than the page boundary (pagesize), the write operation
would overflow the current page and the behaviour can be
undefined (e.g. at24).
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
|
|
Update U-Boot's version of scripts/get_maintainer.pl to sync it up with
the latest changes to the Linux kernel's version of the same script.
The last sync was with Linux kernel version v5.13-rc6. The commits to
the kernel's get_maintainer.pl since then (starting with the most
recent) are:
11fb48961e52 get_maintainer: Honor mailmap for in file emails
26d98e9f78da get_maintainer: don't remind about no git repo when --nogit is used
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Similar change was done by commit b4c2c151b14b ("Kconfig: Remove all
default n/no options") and again sync is required.
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
|
