| Age | Commit message (Collapse) | Author |
|---|
|
This patch provides a driver for i.MX Messaging Unit (MU) using the
commom mailbox framework.
This is ported from Linux (v6.12.8) driver
drivers/mailbox/imx-mailbox.c. Its commit SHA is:
39d7d6177f0c ("mailbox: imx: use device name in interrupt name")
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
|
|
The regulator extras should be placed in the USB H1 regulator node,
the /regulator-usb-h1-vbus. They are already present there in the
upstream DT, so delete this bogus node entirely.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
On i.MX8M SoCs, the /firmware/optee Devicetree node is created just before
booting the OS when OP-TEE is found running. If the node already exists,
this results in an error, which prevents the OS to boot:
Could not create optee node.
ERROR: system-specific fdt fixup failed: FDT_ERR_EXISTS
- must RESET the board to recover.
failed to process device tree
On the i.MX8M systems where CONFIG_OF_SYSTEM_SETUP is defined, the
ft_add_optee_node() function is called before booting the OS. It will
create the OP-TEE Devicetree node and populate it with reserved memory
informations gathered at runtime.
On on most i.MX8M systems the Devicetree is built with an optee node if
CONFIG_OPTEE is defined. This node is indeed necessary for commands and
drivers communicating with OP-TEE, even before attempting OS boot.
The aforementioned issue can happen on the Compulab IOT-GATE-iMX8, which is
the only in-tree i.MX8M system where both CONFIG_OPTEE and
CONFIG_OF_SYSTEM_SETUP are defined (see the imx8mm-cl-iot-gate*
defconfigs).
Deal with an existing optee node gracefully at runtime to fix this issue.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tim Harvey <tharvey@gateworks.com>
|
|
When "fdtfile" is not set, use the "variant" environment variable to
select the correct DTB.
Apalis/Colibri iMX6 V1.2 replaced the STMPE811 ADC/Touch controller
which is EOL with the TLA2024 ADC and AD7879 touch controller. They thus
require a different DTB, which we can easily select with the variant env
variable.
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
Apalis/Colibri iMX6 V1.2 will replace the STMPE811 ADC/Touch controller
which is EOL by the TLA2024 ADC and AD7879 touch controller.
To support this new version, we detect the presence of the TLA2024
during boot and set a new environment variable named "variant". This
will allow us and users to select the correct DT easily.
By probing via I2C we have a robust detection method instead of relying
on the existing "board_rev" environment variable which is set by the
config block. Users can use "variant" in their DT selection and do not
have to map the board revision to a device tree.
"variant" environment variable behaviour:
* Empty or absent for all versions below v1.2 (STMPE811)
* "-v1.2" for all versions starting from v1.2 (TLA2024 + AD7879)
Usage example:
setenv fdtfile imx6q-apalis${variant}-${fdt_board}.dtb
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
Guard the inclusion of tee.bin with the CONFIG_OPTEE symbol to fix the
following build warning:
CHECK u-boot-container.cfgout
WARNING './tee.bin' not found, resulting binary may be not-functional
BINMAN .binman_stamp
OFCHK .config
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
The flag for enabling the ESDHCI_QUIRK_BROKEN_TIMEOUT_VALUE quirk can be
handled easily enough in Kconfig. This lets us remove a function but not
obviously correct usage of the IS_ENABLED() macro.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm into next
CI: https://source.denx.de/u-boot/custodians/u-boot-stm/-/pipelines/25112
- Add drivers for MFD STM32 TIMERS and STM32 PWM and enable them on stm32mp135f-dk
- Restrict _debug_uart_init() usage in STM32 serial driver
- Add support for environment in eMMC on STM32MP13xx DHCOR SoM
- Introduce DH STM32MP15xx DHSOM board specific defconfigs
- Fix CONFIG_BOOTCOUNT_ALTBOOTCMD update on DH STM32MP1 DHSOM
- Update maintainer for board stm32f746-disco
- Fix Linux cmdline for stm32f769-disco
- Cleanup in stm32f***-u-boot.dtsi and in board_late_init() by removing
legacy led and button management.
|
|
This series from Leonard Anderweit <l.anderweit@phytec.de> provides some
improvements to the binman tool and i.MX specific tooling then makes use
of it.
Link: https://lore.kernel.org/r/20250226210501.72794-1-l.anderweit@phytec.de
|
|
Build the imx code singing tool from source instead of relying on the
distro to provide the tool.
Use the debian/unstable branch because the default branch is outdated.
The binary is supposed to be build with docker, work around that by selecting
the correct Makefile directly.
Also append the description and add a link to documentation.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add optional argument make_path to build_from git. The new argument
allows specifying the path to a Makefile in case it is not in the root
of the git repo.
Also adjust the corresponding test.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add optional argument git_branch to build_from_git. The new argument
allows specifying which branch of the repo to use.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Greg Malysa <malysagreg@gmail.com> says:
This series adds all of the supported peripheral drivers for the sc5xx
series of SoCs from Analog Devices and other drivers that are used by
the evaluation kits, such as a GPIO expander used by the EZLITE carrier
boards. This series passes gitlab CI tests.
Link: https://lore.kernel.org/r/20250226173150.13198-1-malysagreg@gmail.com
|
|
Co-developed-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
|
|
This adds support for the ADI-specific SPI driver present in the ADI
SC5xx line of SoCs. This IP block is distinct from the QSPI/OSPI block
that uses the Cadence driver. Both may be used at once with appropriate
pin muxing configuration.
Co-developed-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Co-developed-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Co-developed-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
Signed-off-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
|
|
This adds the ability to load ldr-formatted files to the SHARC
coprocessors using the rproc interface. Only a minimal subset
of rproc functionality is supported: loading and starting
the remote core.
Secure boot and signed ldr verification are not available
at this time through the U-Boot interface.
Co-developed-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Co-developed-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
Signed-off-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
|
|
Add a rudimentary MDMA driver for the Analog Devices SC5xx SoCs,
primarily intended for use with and tested against the QSPI/OSPI
IP included in the SoC.
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
|
|
Co-developed-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
The ADI SC598 includes a Designware QoS 5.20a IP block. This
commit adds support for using the existing ethernet QoS driver
with the SC598 SoC.
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
|
|
Co-developed-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Co-developed-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This adds support for the MUSB-based USB controller found in the
Analog Devices SC57x and SC58x SoCs.
Co-developed-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
|
|
This adds support for the ADP588 GPIO expander from Analog Devices. It
is accessed over I2C and provides up to 18 pins. It is largely a port of
the Linux driver developed by Michael Hennerich
<michael.hennerich@analog.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
|
|
This adds support for using the GPIO pins on the SC5XX family of SoCs
from Analog Devices.
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
|
|
This adds the necessary dt-bindings and documentation to use the ADI
SC5xx pinctrl driver in a device tree. It is not yet available upstream
in the Linux kernel. Eventually, it will be moved there.
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
|
|
This adds support for pin configuration on the Analog Devices SC5XX SoC
family. This commit is largely a port of the Linux driver, which has not
yet been submitted upstream.
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
|
|
This series from Patrick Rudolph <patrick.rudolph@9elements.com> fixes
an issue with how we treat PCIe vs PCI in some cases and fixes the
qemu-arm-sbsa reference platform support.
Link: https://lore.kernel.org/r/20250226135647.194842-1-patrick.rudolph@9elements.com
|
|
Enable PCI enumeration by default to get the Bochs display driver up
and running before the boot medium is scanned.
This is just to enhance the user-experience while booting the machine.
TEST: U-Boot logo, version, log output and the U-Boot shell is visible
on the display device.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
qemu's sbsa-ref is always using a 64bit CPU and the PCI prefetch MMIO
window is located above 4GiB, thus always enable SYS_PCI_64BIT.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Legacy PCI devices, like qemu's Bochs VGA device, are allowed to have
prefetchable 32-bit BARs, while PCIe devices are not allowed to have
32-bit prefetchable BARs. Typically prefetchable BARs are 64-bit and
typically the prefetch MMIO window is also 64-bit and placed above
4GiB, as it's the case on qemu sbsa-ref.
Currently the U-Boot code assumes that prefetchable BARs are
64-bit BARs and always tries to assign them into the prefetch
MMIO window.
When a 32-bit BAR is marked as prefetch, but the prefetch area is
not within the first 4GiB of the address space, then downgrade the
BAR and place it in the non-prefetch MMIO window.
For prefetch BARs there's no downside on being placed in non prefetch
MMIO areas, besides the possible slower performance when a driver tries
to map it Write-Combine.
TEST: Fixes pci_auto on QEMU sbsa-ref fails to autoconfigure BAR0.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Since commit 948da7773e34 ("arm: Add new config option ARCH_VERY_EARLY_INIT")
debug_uart_init() is called respectively in crt0.S and crt0_64.S.
That means that _debug_uart_init() is called for all STM32MP platforms
even for those which doesn't support SPL_BUILD.
So restrict _debug_uart_init() execution for platforms which can have
SPL_BUILD enabled (STM32MP1 platform only).
It's more needed to call debug_uart_init() in stm32mp1/cpu.c.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Vikas has left STMicroelectronics several years ago.
Put myself as maintainer of stm32f746-disco board.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The pwm source TIM1_CH3N channel (on PE12) in inverted polarity mode
will be used to manage the brightness of the panel backlight on
STM32MP135F-DK.
Signed-off-by: Cheick Traore <cheick.traore@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Enable the following configs:
* CONFIG_MFD_STM32_TIMERS: enables support for the STM32 multifunction
timer
* CONFIG_DM_PWM: enables support for pulse-width modulation devices
* CONFIG_CMD_PWM: enables 'pwm' command to control PWM channels
* CONFIG_PWM_STM32: enables support for the STM32 PWM devices
Signed-off-by: Cheick Traore <cheick.traore@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add driver to support pwm on STM32MP1X SoCs. The PWM signal is generated
using a multifuntion timer which provide a pwm feature. Clock rate and
addresses are retrieved from the multifunction timer driver.
Signed-off-by: Cheick Traore <cheick.traore@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add support for STM32MP timer multi-function driver.
These timers can be use as counter, trigger or pwm generator.
This driver will be used to manage the main resources of the timer to
provide them to the functionnalities which need these ones.
Signed-off-by: Cheick Traore <cheick.traore@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-tegra into next
|
|
https://source.denx.de/u-boot/custodians/u-boot-tegra into next
|
|
into next
|
|
The value written to the RFLR register includes the length of the CRC
data at the end of each Ethernet frame. So we need to increase the value
written to this register to ensure that we can receive full size frames.
While we're here we can also copy the improved comment from the Linux
kernel.
Fixes: 8ae51b6f324e ("net: ravb: Add Renesas Ethernet RAVB driver")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Fix comment
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The Renesas RAVB driver always requires bitbang MDIO bus support.
Fixes: 8ae51b6f324e ("net: ravb: Add Renesas Ethernet RAVB driver")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Following on from commit 9a699a0a0d62 ("clk: rzg2l: Ignore enable for
core clocks"), we also need to ignore attempts to disable core clocks to
avoid the need for conditionals around clk_disable_bulk() calls in
drivers which support both RZ/G2L and other Renesas SoCs.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Inline mdio_init() back into mdio_alloc(), separate
access to mdio_init() is no longer necessary.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
These functions are no longer necessary, remove them.
The struct bb_miiphy_bus is no longer necessary either,
remove it as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Use mdio_alloc() again to allocate MDIO bus. This is possible
because all the miiphybb parameters and ops passing is handled in
at bb_miiphy_read()/bb_miiphy_write() level.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Use mdio_alloc() again to allocate MDIO bus. This is possible
because all the miiphybb parameters and ops passing is handled in
at bb_miiphy_read()/bb_miiphy_write() level.
This also fixes previously missed bb_miiphy_free() in .remove
callback of this driver. which does not pose a problem anymore.
Fixes: 08eefb5e792d ("net: sh_eth: Allocate bb_miiphy using bb_miiphy_alloc() and fill in callbacks")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Use mdio_alloc() again to allocate MDIO bus. This is possible
because all the miiphybb parameters and ops passing is handled in
at bb_miiphy_read()/bb_miiphy_write() level.
This also fixes previously missed bb_miiphy_free() in .remove
callback of this driver. which does not pose a problem anymore.
Fixes: 079eaca6e7b4 ("net: ravb: Allocate bb_miiphy using bb_miiphy_alloc() and fill in callbacks")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Use mdio_alloc() again to allocate MDIO bus. This is possible
because all the miiphybb parameters and ops passing is handled in
at bb_miiphy_read()/bb_miiphy_write() level.
This also fixes previously missed bb_miiphy_free() in .remove
callback of this driver. which does not pose a problem anymore.
Fixes: cbb69c2fafcc ("net: designware: Allocate bb_miiphy using bb_miiphy_alloc() and fill in callbacks")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Remove the priv member from struct bb_miiphy_bus and its assignment
from drivers. This turns struct bb_miiphy_bus int struct mii_dev
wrapper, to be cleaned up next.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
Access to MDIO bus private data can be provided by both
struct mii_dev .priv member and struct bb_miiphy_bus .priv
member, use the former directly and remove .priv from the
later. Drop unused bb_miiphy_getbus(). This removes any
dependency on struct bb_miiphy_bus from the miiphybb code,
except for helper functions which will be removed later.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
The access to struct bb_miiphy_bus_ops via ops pointer in
struct bb_miiphy_bus is not necessary with wrappers added
in previous patch. Pass the ops pointer directly to both
bb_miiphy_read() and bb_miiphy_write() functions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
