| Age | Commit message (Collapse) | Author |
|---|
|
Enable EFI_SET_TIME on the sandbox and QEMU ARM to ensure that we compile
and test the relevant code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Using constants instead of anonymous numbers increases code readability.
Fixes: 704df6aa0a28 ("fs: fat: refactor write interface for a file offset")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
0x05 is used as replacement letter for 0xe5 at the first position of short
file names. We must not skip over directory entries starting with 0x05.
Cf. Microsoft FAT Specification, August 30 2005
Fixes: 39606d462c97 ("fs: fat: handle deleted directory entries correctly")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When trying to create a file in the full root directory of a FAT32
filesystem a NULL dereference can be observed.
When the root directory of a FAT16 filesystem is full fill_dir_slot() must
return -1 to signal that a new directory entry could not be allocated.
Fixes: cd2d727fff7e ("fs: fat: allocate a new cluster for root directory of fat32")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- STM32 MCU's DT update
- Add DHCOM based STM32MP15x PicoITX board
- Correct ALIGN macro usage for on syram for SPL dcache support
- Fixes on DHCOM: uSD card-detect GPIO and Drop QSPI CS2
- Fix compilation issue for spl_mmc_boot_partition
- Fix MTD partitions for serial boot
- Add support of MCU HOLD BOOT with reset for stm32 remoteproc
(prepare alligneent with kernel DT)
- Correct bias information and support in STM32 soc and STMFX
- Support optional vbus in usbphyc
- Update FIT examples to avoid kernel zImage relocation before decompression
|
|
Update kernel load address for FIT examples to avoid relocation:
- Kernel example uses Image.gz with U-Boot gzip decompression
at final kernel location 0x0xC0008000.
- Copro example loads zImage at a correct location (0xC4000000),
to avoid zImage relocation before decompression by kernel code.
An other solution to avoid zImage relocation is to align
the kernel load and entry address with the real location in FIT
(the relocation of zImage is skipped in U-Boot bootm command for
identical address) but it is less flexible because this offset
depends on FIT content:
For example:
## Loading kernel from FIT Image at c2000000 ...
Using 'ev1' configuration
Trying 'kernel' kernel subimage
Description: Linux kernel
Created: 2020-10-22 9:08:32 UTC
Type: Kernel Image
Compression: uncompressed
Data Start: 0xc20000cc
The kernel offset in FIT is 0xCC in FIT and zImage is decompressed at
0xC0008000 by kernel code:
kernel {
description = "Linux kernel";
data = /incbin/("zImage");
type = "kernel";
arch = "arm";
os = "linux";
compression = "none";
load = <0xC20000cc>;
entry = <0xC20000cc>;
hash-1 {
algo = "sha1";
};
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This patch adds support for optional vbus regulator.
It is managed on phy_power_on/off calls and may be needed for host mode.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Update pin name to avoid duplicated name with SOC GPIO
gpio0...gpio15 / agpio0....agpio7: add a stmfx prefix.
This pin name can be used in pinmux command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The device name is used in pinmux command and in log trace
so it is better to use the parent parent name ("stmfx@42" for
example) than a generic name ("pinctrl" or "stmfx-gpio")
to identify the device instance.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use the bias configuration for all the GPIO configurations and not
only for input GPIO, as indicated in Reference manual
(Table 81. Port bit configuration table).
Fixes: 43efbb6a3ebf0223f9eab8d45916f602d876319f ("gpio: stm32: add ops get_dir_flags")
Fixes: f13ff88b61c32ac8f0e9068c41328b265ef619eb ("gpio: stm32: add ops set_dir_flags")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Display the bias information for input gpios or AF configuration,
and not only for output pin, as described in Reference manual
(Table 81. Port bit configuration table).
Fixes: da7a0bb1f279 ("pinctrl: stm32: add information on pin configuration")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The coprocessor is running as soon as the hold boot is de-asserted.
So indicate this running state and save the resource table even
if the protective assert, to avoid autonomous reboot, is failed.
This error case should never occurs.
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Use the reset function to handle the hold boot bit in RCC
with device tree handle with MCU_HOLD_BOOT identifier.
This generic reset allows to remove the two specific properties:
- st,syscfg-holdboot
- st,syscfg-tz
This patch prepares alignment with kernel device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Handle the register RCC_MP_GCR without SET/CLR registers
but with a direct access to bit BOOT_MCU:
- deassert => set the bit: The MCU will not be in HOLD_BOOT
- assert => clear the bit: The MCU will be set in HOLD_BOOT
With this patch the RCC driver handles the MCU_HOLD_BOOT_R value
added in binding stm32mp1-resets.h
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Remove the update of the MTD partitions in kernel device tree
for serial boot (USB / UART), and the kernel will use the MTD
partitions define in the loaded DTB because U-Boot can't known the
expected flash layout in this case.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
spl_mmc_boot_partition is only defined when
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION is defined.
Signed-off-by: Richard Genoud <richard.genoud@posteo.net>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
The QSPI CS2 is not used on DHCOM, remove the pinmux and flash@1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
The uSD slot card-detect GPIO is connected to PG1, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Correct the ALIGN macro usage in mmu_set_region_dcache_behaviour
call: the address must use ALIGN_DOWN and size can use ALIGN macro.
With STM32_SYSRAM_BASE=0x2FFC0000 and MMU_SECTION_SIZE=0x100000 for
STM32MP15x the computed address was 30000000 instead of 2ff00000.
Fixes: 43fe9d2fda24 ("stm32mp1: mmu_set_region_dcache_behaviour")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Fix typo "firsct"
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Commit 4b2be78ab66c ("time: Fix get_ticks being non-monotonic")
puts in evidence that get_ticks is called before timer initialization.
Fix it by initializing timer before relocation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Device tree alignment with kernel v5.10-rc1.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Since kernel v4.8-rc1, commit 05b23ebc2bd9 ("ARM: dts: armv7-m: remove skeleton.dtsi include"),
skeleton.dtsi file is no more included.
This synchronization is needed to avoid to get 2 memory node
in DTB file if, in DTS file, memory node is declared with the correct
syntax as following:
memory@90000000 {
device_type = "memory";
reg = <0x90000000 0x800000>;
};
Then in DTB, we will have the 2 memory nodes, which is incorrect and
cause misbehavior during DT parsing by U-boot:
memory {
device_type = "memory";
reg = <0x00 0x00>;
};
memory@90000000 {
device_type = "memory";
reg = <0x90000000 0x800000>;
};
Issue found when synchronizing MCU's STM32 DT from kernel v5.10-rc1.
When using fdtdec_setup_mem_size_base() or fdtdec_setup_memory_banksize()
API, first above memory node is found (with reg = <0x00 0x00>), so
gd->ram_size, gd->ram_base, gd->bd->bi_dram[bank].start and
gd->bd->bi_dram[bank].size are all set to 0 which avoid boards to boot.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
- DWC2, DWC3 fixes
|
|
- Assorted pinctrl updates
|
|
If reset DT property is not present, -ENOENT is returned.
But it's not really error.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
If CONFIG_PHY is not enabled then the dwc3_setup_phy()
returns ENOTSUPP which can be still valid and intentional
so modify error check to handle this -ENOTSUPP.
The same error handling exists in drivers/usb/host/xhci-dwc3.c already
added by commit d648a50c0a27 ("dwc3: move phy operation to core.c").
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
On some board, the ID pin is not connected so the B session must be
overridden with "u-boot,force_b_session_valid" but the VBus sensing
must continue to be handle.
To managed it, this patch adds a new DT field
"u-boot,force-vbus-detection" to use with "u-boot,force_b_session_valid"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Drop unused members from struct sh_pfc_pinctrl.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
|
|
This driver supports both RZ/G2H and R-Car H3 SoCs.
Optimize pinctrl image size for RZ/G2H, when support for R-Car H3
(R8A7795) is not enabled
Based on the similar patch on Linux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
|
|
This driver supports both RZ/G2N and R-Car M3-N SoCs.
Optimize pinctrl image size for RZ/G2N, when support for R-Car M3-N
(R8A77965) is not enabled.
Based on the simialr patch on Linux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
|
|
This driver supports both RZ/G2M and R-Car M3-W/W+ SoCs.
Optimize pinctrl image size for RZ/G2M, when support for R-Car M3-W/W+
(R8A7796[01]) is not enabled.
Based on the similar patch on Linux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
|
|
Renesas RZ/G2H (r8a774e1) is pin compatible with R-Car H3 (r8a77951),
however it doesn't have several automotive specific peripherals. Add
a r8a77951 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77951 and r8a774e1 SoC.
PFC changes are synced from mainline linux-5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
|
|
Renesas RZ/G2N (r8a774b1) is pin compatible with R-Car M3-N (r8a77965),
however it doesn't have several automotive specific peripherals. Add
a r8a77965 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77965 and r8a774b1 SoC.
PFC changes are synced from mainline linux-5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc3 (2)
The parameter check for UEFI service GetNextVariableName() is corrected.
The dependencies of CONFIG_DFU_TFTP are simplified.
The set of supported hash algorithms reported by the EFI_TCG2_PROTOCOL is
corrected.
|
|
If GetNextVariableName() is called with a non-existing combination of
VariableName and VendorGuid, return EFI_INVALID_PARAMETER.
If GetNextVariableName() is called with a string that is not zero
terminated, return EFI_INVALID_PARAMETER.
Reformat a line over 80 characters.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
On pull reuqest
https://lists.denx.de/pipermail/u-boot/2020-November/432735.html
V4 of the patchset was sent instead of the v5.
This is the v4->v5 missing diff
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Since CONFIG_UPDATE_COMMON always selects CONFIG_DFU_WRITE_ALT, we can
drop the latter from dependencies of CONFIG_DFU_TFTP.
Fixes: 3149e524fc1e ("common: update: add a generic interface for FIT
image")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-rc3
Microblaze:
- Enable GC
- Get rid of xparameters.h and switch to DT for CFI
- Fix config file
tpm:
- Fix TPM code
zynqmp:
- Enable TPM by default
- Remove unused macros
fru:
- Several fixes especially use limit for recording
|
|
Add additional fields. They will be just recorded and filled but not shown.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
If customs fields in board area are used it will likely go over allocated
space in struct fru_board_data. That's why calculate limit of this
structure to make sure that different data is not rewritten by accident.
When limit is reached stop to record fields.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
capture variable is bool which is just one byte and it is just causing
unaligned accesses. Better to have it as last entry in the structure.
It also simplify offset calculation for initial header copy.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
TPMs are becoming popular that's why enable drivers and command for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is no reason to have these macros. But record offsets of missing
register in the structure for future use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is no need for GD to be used and priv variable is unused.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Remove fixed configuration and detect flash based on DT.
Also increase amount of flash sectors to 2048 because on kc705 flash has
1027 sectors.
Bank # 1: CFI conformant flash (16 x 16) Size: 128 MB in 1027 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8962
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
XIP is not enabled in SPL. SPL_NOR is enabled but any macro setting with
using SYS_FLASH_BASE are wrong because it is not aligned with DM.
That's why change these macro and align them with TEXT_BASE macro.
Information should be find at run time based on DT but implementation is
not done yet.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
CONFIG_SYS_FDT_SIZE is not use anywhere that's why remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is no need to use this file anymore. Include it in main config file
and simplify logic based on it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
