| Age | Commit message (Collapse) | Author |
|---|
|
and make them static
The variables is_validate_window_per_if, is_validate_window_per_pup,
sweep_cnt and is_run_leveling_sweep_tests are only used if
DDR_VIEWER_TOOL macro is defined, so define them only in that case.
Make them static since they are only used in ddr3_debug.c.
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
The variables is_default_centralization, is_tune_result and
is_bist_reset_bit are never used.
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
won't print anything
Return from ddr3_tip_print_log() early if we won't print anything
anyway.
This way the compiler can optimize away the VALIDATE_IF_ACTIVE() calls
in the for-loop, so if the SILENT_LIB macro is defined, no code is
generated for the rest of the function, which saves some space.
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
Turris Omnia defconfig is nearing image size limit. Disable ext4 write
support to reserve space for more important stuff.
This reduces the size of the KWB image by ~19 KiB.
If in the future U-Boot supports compressing itself and decompressing
on load, we may enable this again.
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
- Change the spi-max-frequency to 50000000 (50 Mhz). According to the
data sheet[1], the MX25L3205D max frequency is 86 Mhz. Using 50 Mhz in
the DTS to ensure u-boot is consistent with what Linux kernel expected.
- Update GPIO fan to conform to the latest DT binding.
[1]
https://www.macronix.com/Lists/Datasheet/Attachments/8575/MX25L3205D,%203V,%2032Mb,%20v1.5.pdf
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
|
|
The CONFIG_ENV_OFFSET is undefined if boot device is UART
(CONFIG_MVEBU_SPL_BOOT_DEVICE_UART), or envs are not stored on flash
(CONFIG_ENV_IS_NOWHERE). Check for CONFIG_ENV_IS_IN_SPI_FLASH as the first
condition to determine whether env_sf_get_env_addr() should be provided.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
|
|
Add support for a Marvell Armada 3720 device variant
Signed-off-by: Benjamin Schneider <ben@bens.haus>
|
|
- Re-instate the zlib update, so we can fix it for this release,
assorted whitespace cleanups, allow mkimage to 'auto-conf' signing of
scripts, enhance ELF image support, add more HW rev support to e1000
driver, update am64x_evm config, correct mpc8xxx watchdog, update
phycore-am6 docs.
|
|
Now that the release has happened, bring back the update to zlib.
This reverts commit bbacdd3ef7762fbdeab43ceea5205d1fd0f25bbd.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Timer value is a 16 bits calculated from the wanted timeout and the
system clock. On powerpc/8xx, a timeout of 2s gives a value which
is over U16_MAX so U16_MAX shall be used. But the calculation is
casted to u16 so at the end the result is 63770 instead of 128906.
So the timer gets loaded with 63770 instead of 65535. It is not
a big difference in that case, but lets make the code correct and
cast to u32 instead of u16.
Fixes: 26e8ebcd7cb7 ("watchdog: mpc8xxx: Make it generic")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
This patch fixes the I225 hardware default value
at 0x15FD meaning empty flash image
or the NVM configuration loading failed
Signed-off-by: Marjolaine Amate <marjolaine.amate@odyssee-systemes.fr>
|
|
This patch adds support for Intel Foxville I226
devices LM,V,I,K in e1000 driver.
Signed-off-by: Marjolaine Amate <marjolaine.amate@odyssee-systemes.fr>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
|
|
The board has the TCA9554 I2C GPIO expander chip for expansion
board presence detection logic.
Enable the relevant I2C GPIO drivers.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
|
|
Some operating systems (e.g. seL4) and embedded applications are ELF
images. It is convenient to use FIT-images to implement trusted boot.
Added "elf" image type for booting using bootm command.
Signed-off-by: Maxim Moskalets <maximmosk4@gmail.com>
|
|
U-Boot configured for verified boot with the "required" option set to
"conf" also checks scripts put in FIT images for a valid signature, and
refuses to source and run such a script if the signature for the
configuration is bad or missing. Such a script could not be packaged
before, because mkimage failed like this:
% tools/mkimage -T script -C none -d tmp/my.scr -f auto-conf -k tmp -g dev -o sha256,rsa4096 my.uimg
Failed to find any images for configuration 'conf-1/signature'
tools/mkimage Can't add hashes to FIT blob: -1
Error: Bad parameters for FIT image type
This is especially unfortunate if LEGACY_IMAGE_FORMAT is disabled as
recommended.
Listing the script configuration in a "sign-images" subnode instead,
would have added even more complexity to the already complex auto fit
generation code.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
|
|
Describe how to boot via UART.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Drop all duplicate newlines from config headers.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-snapdragon
Various minor fixes and improvements:
* Fix Qualcomm SPMI v5 support
* Move default environment to a file
* Add support for special pins (e.g ufs/mmc reset/data pins)
* IPQ moves to OF_UPSTREAM and receives some cleanup and MAINTAINERS
changes
* Add a reset driver for devices without PSCI
* msm8916 USB clock improvements for mobile devices
|
|
Branch contains minor improvemets for existing tegra devices along
with bring up of 4 new devices (ASUS Transformers T20, Microsoft
Surface RT, Lenovo Ideapad Yoga 11 and WEXLER Tab 7t).
|
|
This change was brought in by accident, revert.
This reverts commit 51aabf50e57f5139de31a4850347edbad8bb338b.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Commit ee1d8aa5ecf7 ("spmi: msm: support controller version 7") broke
support for channels > 128 on v5 controllers, resulting in some
peripherals (like the power button / pon) working but others (like
gpios) reading bogus data.
Correct max_channels for v5 controllers.
Fixes: ee1d8aa5ecf7 ("spmi: msm: support controller version 7")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Make use of CONFIG_DEFAULT_ENV_FILE and move the default qcom
environment to a file under board/qualcomm.
This is much cleaner and means we don't need to recompile on changing
the environment.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Most devices have buttons exposed via the PMIC, the button polling
therefore triggers a log spam if debug logging is enabled.
Demote these to debug() so that they aren't printed unless LOG_DEBUG is
defined explicitly for this file.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add the special pins configuration data to allow setup the bias
of the UFS and SDCard pins on the SM8650 SoC.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
Add the special pins configuration data to allow setup the bias
of the UFS and SDCard pins on the SM8550 SoC.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
Use the previously introduced msm_special_pin_data to setup the special
pins configuration if the SoC driver have them specified.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
In order to help setup pin configuration for special pins (UFS, SDCard),
introduce the msm_special_pin_data struct largely inspired from the
Linux conterpart but with only U-Boot required fields.
This struct is added to the pins_data to allow specifying the special
pins data for each SoC.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
Add support for bias-pull-down as an alternate of bias-pull-up.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
I2C clocks are not initialized by the SBL, so lets add support for clocks
required by both of the QUP I2C controllers.
BLSP1 AHB clock is already initialized by SBL, but QUP I2C driver is
requesting it so we have to add it to the enable list.
Based off QCS404 clock driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
Pinctrl drivers were moved to a dedicated directory but the entry was never
updated, so add the pinctrl-ipq4019 driver entry.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
The reset handling was added to the clock drivers but the entry was never
updated, so add the clock-ipq4019 driver instead.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
The separate clock and reset dt-bindings for IPQ40XX were merged into one
recently, but the entry was not updated so do it now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
Luka Kovacic is no longer at Sartura, so remove him as one of IPQ40xx
maintainers.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
|
We want to use OF_UPSTREAM on IPQ40XX as its well supported upstream, so
lets drop our downstream DTSI.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Now that drivers are compatible enough with the upstream DTS, there is no
reason to not use the upstream DTS, so imply OF_UPSTREAM by default.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Provide basic DRAM info population from DT, cache setting and the
board_init stub.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Number of Qualcomm ARMv7 SoC-s did not use PSCI but rather used PSHOLD
(Qualcomm Power Supply Hold Reset) bit to trigger reset or poweroff.
Qualcomm IPQ40XX is one of them, so provide a simple sysreset driver based
on the upstream Linux one, it is DT compatible as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
This seems to be necessary on my samsung-a5. Without this patch, the
first access of EHCI registers causes a bus stall and subsequent reset.
I am unsure why this wasn't already necessary for db410c, perhaps those
clocks are already enabled on boot.
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Sam Day <me@samcday.com>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The newer "register map for simple gate clocks" support added for qcom
clocks is used. As a result gcc_apq8016 now has a mixture of the old and
new styles. I didn't (and still don't!) feel comfortable enough in this
area to update the existing code.
Signed-off-by: Sam Day <me@samcday.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Enable the clock/pinctrl drivers for these two SoCs. Previously left out
due to only being used on the db410c and db820c respectively which both
have their own board code. We can still boot these with most features
working without that board code.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Sam Day <me@samcday.com>
|
|
The Lenovo IdeaPad Yoga 11 is a hybrid laptop/tablet Windows RT-based
computer released in late 2012. The device uses a 1.3 GHz quad-core
Nvidia Tegra 3 chipset with 2 GB of RAM, features a 11.6 inch 1366x768
screen and 32/64 GB of internal memory that can be supplemented with
a microSDXC card slot, full size SD card slot and 2 full size USB 2.0
ports.
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
Surface RT is a hybrid tablet computer developed and manufactured
by Microsoft and shipped with Windows RT. The tablet uses a 1.3 GHz
quad-core Nvidia Tegra 3 chipset with 2 GB of RAM, features 10.8
inch 1366x768 screen and 32/64 GB of internal memory that can be
supplemented with a microSDXC card giving up to 200 GB of
additional storage.
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
WEXLER Tab 7t is a mini tablet computer developed by WEXLER that
runs the Android operating system. The device features a 7.0-inch
(180 mm) HD display, an Nvidia Tegra 3 quad-core chip, 1 GB of RAM,
8, 16 or 32 GB of storage that can be supplemented with a microSDXC
card giving up to 64 GB of additional storage and a full size USB
port.
Tested-by: Maksim Kurnosenko <asusx2@mail.ru>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
The Asus Eee Pad Transformer family are 2-in-1 detachable/slider
tablets developed by Asus that run the Android operating system.
The Eee Pad Transformers feature a 10.1-inch (260 mm) display,
an Nvidia Tegra 2 dual-core chip, 1 GB of RAM, and 16/32 GB of storage.
Transformers board derives from Nvidia Ventana development board.
This patch brings support for all 3 known T20 Transformers:
- Asus Eee Pad Transformer TF101
- Asus Eee Pad Transformer TF101G
- Asus Eee Pad Slider SL101
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # ASUS TF101
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
Fixes implicit declaration of function 'hextoul'
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
Drop boot device sequence re-definition since now it is default.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
This ensures that the device can boot from a USB device prior to MMC. Useful
cases are when installing a new OS from USB while MMC still has a working OS
configuration or if the OS configuration is broken in late boot stages
(kernel boots but the system does not start).
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
Use existing nvidia,head device tree property to get DC controller id.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
