summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2023-12-19board: compal: paz00: clean up the boardSvyatoslav Ryhel
Since implementation of pinctrl driver for T20 Paz00 can switch to device tree pinmux setup along with remove of board pinmux and some minor device tree and defconfig tweaks. Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20 Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19board: htc: endeavoru: switch to DM pinmuxSvyatoslav Ryhel
Drop the pinmux setup in the board in favor of setting it up in the device tree. Device tree nodes match nodes used for the Linux device tree and are set according to the downstream kernel.  Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19board: asus: transformer: switch to DM pinmuxSvyatoslav Ryhel
Drop the pinmux setup in the board in favor of setting it up in the device tree. Device tree nodes match nodes used in the Linux device tree.  Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19board: lg: x3-t30: switch to DM pinmuxSvyatoslav Ryhel
Drop the pinmux setup in the board in favor of setting it up in the device tree. Device tree nodes match nodes used for the Linux device tree and are set according to the service manual. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19board: asus: grouper: switch to DM pinmuxSvyatoslav Ryhel
Drop the pinmux setup in the board in favor of setting it up in the device tree. Device tree nodes match nodes used in the Linux device tree. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19drivers: pinctrl: tegra: incorporate existing codeSvyatoslav Ryhel
Move all existing pinmux and funcmux code into a dedicated folder in pinctrl to simplify further maintenance. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19drivers: pinctrl: create Tegra DM pinctrl driverSvyatoslav Ryhel
The existing pinctrl driver available for Tegra SOC is well designed, but it lacks DM support. Let's add a DM compatible overlay, which allows use of the device tree, along with preserving backward compatibility with all existing setups and the ability to use it in SPL board configuration stage. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19ARM: mach-tegra: rearrange SPL configsSvyatoslav Ryhel
SPL configs are used only by the ARMv7-based Tegra SOC's, so move SPL_SYSRESET under TEGRA_ARMV7_COMMON selection and enable SPL_DM since SPL_SYSRESET depends on it. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19mmc: tegra: use max-frequency from device tree if providedPeter Geis
The driver currently hard-codes the max freqency for the sdhci controllers. If the controller is unable to operate at the max frequency, the mmc card will not be available on the first scan. Subsequent scans will eventually find a working combination. Fix this by allowing the driver to check for the max-frequency property and default to the original value if it doesn't exist. Signed-off-by: Peter Geis <pgwipeout@gmail.com> Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19ARM: tegra114: clock: implement PLLD2 supportSvyatoslav Ryhel
PLLD2 is a simple clock (controlled by 2 registers) and appears starting from T30. Primary use of PLLD2 is as main HDMI clock parent. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19ARM: tegra30: clock: implement PLLD2 supportSvyatoslav Ryhel
PLLD2 is a simple clock (controlled by 2 registers) and appears starting from T30. Primary use of PLLD2 is as main HDMI clock parent. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19ARM: tegra: clock: support get and set rate for simple PLLSvyatoslav Ryhel
Simple PLL clocks like PLLD2 were omitted since they do not share common 4 register structure with main clocks. Such clocks are containd in simple PLL group. Only clock_start_pll function supported them. This patch expands this support on clock_set_rate and clock_get_rate which should make simple PLL clocks equal to main PLL clocks. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19drivers: gpio-uclass: support PMIC GPIO childrenSvyatoslav Ryhel
UCLASS_PMIC may have GPIO children without exposed fdt node, in this case if requesting fails, check if uclass is PMIC. Restrict build for supported devices only to save those precious bytes on devices with no spare memory. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19drivers: gpio: implement PALMAS GPIO cellSvyatoslav Ryhel
Add gpio driver for TI Palmas series PMIC. This has 8 gpio which can work as input/output. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19drivers: gpio: implement MAX77663 GPIO cellSvyatoslav Ryhel
MAXIM Semiconductor's PMIC, MAX77663 has 8 GPIO pins and 3 GPIO-like pins. It also supports interrupts from these pins. Add GPIO driver for these pins to control via GPIO APIs. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
2023-12-19Merge patch series "Fix J7200 kernel boot when using upstream u-boot"Tom Rini
Reid Tonking <reidt@ti.com> says: Since the 09.01.00.002 release of ti-linux-firmware [0] upstream uboot has led to the kernel hanging during boot [1] for the TI J7200 S0C. The issue was found to be a few patches that had be added to ti-u-boot, but not yet upstreamed. This series adds the missing two patches to allow upstream u-boot to boot the kernel properly [2]. [0] https://git.ti.com/cgit/processor-firmware/ti-linux-firmware/commit/?h=ti-linux-firmware-next&id=952fd03e36a50ec070e73560dc1060102d637ce0 Boot logs: [1] https://gist.github.com/reidt1/5f4e85a0db258bcf20d7168bd0caebd0 [2] https://gist.github.com/reidt1/e950dc97f15ad0a09623d64f81edac39 Links to patches on ti-u-boot: https://git.ti.com/cgit/ti-u-boot/ti-u-boot/commit/?h=ti-u-boot-2023.04-next&id=d878fbef4d4460e87608d8d2dfe5311499de49c5 https://git.ti.com/cgit/ti-u-boot/ti-u-boot/commit/?h=ti-u-boot-2023.04-next&id=543e735fe495be233a8a75b19b3d7f8ed44251e0
2023-12-19Merge patch series "Add support for MediaTek MT8365 EVK Board"Tom Rini
Julien Masson <jmasson@baylibre.com> says: This patch series add the support for the MediaTek MT8365 EVK Board [1]. Most of the code have been copied/adapted from Linux tag v6.7-rc2. For now we only enable/test these features: Boot, UART, Watchdog and MMC. [trini: This includes two clocks not listed in the Linux binding, which needs resyncing later]
2023-12-19Merge branch '2023-12-19-assorted-platform-updates' into nextTom Rini
- Assorted platform updates for TI K3, vexpress64, mediatek and related cleanups to the DW GPIO driver and OPTEE
2023-12-19arm: dts: k3-j7200-r5-common-proc-board: Set parent clock for clock ID 323Reid Tonking
Previously, dynamic frequency scaling supported rates only through fixed divison. This virtual clock mux configuration enables more varied rates on A72 clock ID 202 by setting up the required register. Reviewed-by: Udit Kumar <u-kumar1@ti.com> Signed-off-by: Apurva Nandan <a-nandan@ti.com> Signed-off-by: Reid Tonking <reidt@ti.com>
2023-12-19arm: mach-k3: j72xx: add new 'virtual' muxBryan Brattlof
In order for the Cortex-A72s to operate at different frequencies other than the default 2GHz, add in a new 'virtual' mux (a mux that does not physically exist in the clock tree) that can be selected. CC: Vishal Mahaveer <vishalm@ti.com> Signed-off-by: Bryan Brattlof <bb@ti.com> Signed-off-by: Apurva Nandan <a-nandan@ti.com> Signed-off-by: Reid Tonking <reidt@ti.com> Reviewed-by: Udit Kumar <u-kumar1@ti.com>
2023-12-19board: mediatek: add MT8365 EVK board supportJulien Masson
This adds support for the MT8365 EVK board with the following features enabled/tested: Boot, UART, Watchdog and MMC. Signed-off-by: Julien Masson <jmasson@baylibre.com>
2023-12-19dt-bindings: clock: add Mediatek MT8365 pinctrl bindingsJulien Masson
This adds the pinctrl bindings for Mediatek MT8365 SoC based on the dt-bindings in Linux tag v6.7-rc2. (commit 8b4c397d88d97d4fd9c3f3527aa66688b1a3387a) Signed-off-by: Julien Masson <jmasson@baylibre.com>
2023-12-19arm: mediatek: add support for MediaTek MT8365 SoCJulien Masson
This patch adds basic support for MediaTek MT8365 SoC. The dtsi has been copied from Linux source code tag v6.7-rc2. (commit 9b5d64654ea8f51fe1e8e29ca1777b620be8fb7c) Signed-off-by: Julien Masson <jmasson@baylibre.com>
2023-12-19dt-bindings: power: add power-domain header for MediaTek MT8365 SoCJulien Masson
Add power-domain header for MediaTek MT8365 SoC copied from Linux source code tag v6.7-rc2. (commit a1571f1f333c2fced076f0d54ed771d1838d827f) Signed-off-by: Julien Masson <jmasson@baylibre.com> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
2023-12-19clk: mediatek: add clock driver support for MediaTek MT8365 SoCJulien Masson
This patch adds clock driver support for MediaTek MT8365 SoC. The changes are based on the Linux source code tag v6.7-rc2. clk-mt8365.c has been written based on these kernel files: - clk-mt8365.c (a96cbb146a9736f501fe66ebda6a9018735e5e8a) - clk-mt8365-apmixedsys.c (65c9ad77cbc0eed78db94d80041aba675cfbdfa9) And adapted following the clk attributes supported by U-Boot. Signed-off-by: Julien Masson <jmasson@baylibre.com> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
2023-12-19dt-bindings: clock: add Mediatek MT8365 SoC clock bindingsJulien Masson
This adds the clock bindings for Mediatek MT8365 SoC based on the dt-bindings in Linux tag v6.7-rc2. (commit c61978175ac1337f028ac1f956666f16db84f4e5) Signed-off-by: Julien Masson <jmasson@baylibre.com> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
2023-12-19arm: mach-k3: am625: Relax emmc boot conditionMichael Trimarchi
spl_mmc_emmc_boot_partition return a number different from 0 if the partition is a boot one. We can have the uboot img for instance in a raw offset in emmc partition 0 so we would like to continue to load the next stage. If the user want to use EMMC as boot device allow him to use any part of the emmc and not only boot partition Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
2023-12-19mmc: mediatek: set b_max according CONFIG_SYS_MMC_MAX_BLK_COUNTJulien Masson
The block count limit on MMC based devices should be set according to CONFIG_SYS_MMC_MAX_BLK_COUNT instead of hardcoding value. Signed-off-by: Julien Masson <jmasson@baylibre.com>
2023-12-19gpio: dw: Drop unused headersMaksim Kiselev
Drop headers which are not used or needed in this file. Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
2023-12-19tee: optee: don't enumerate services if there ain't anyEtienne Carriere
Change optee driver service enumeration to not enumerate (and allocate a zero sized shared memory buffer) when OP-TEE reports that there is no service to enumerate. This change fixes an existing issue that occurs when the such zero sized shared memory buffer allocated from malloc() has a physical address of offset 0 of a physical 4kB page. In such case, OP-TEE secure world refuses to register the zero-sized shared memory area and makes U-Boot optee service enumeration to fail. Fixes: 94ccfb78a4d6 ("drivers: tee: optee: discover OP-TEE services") Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
2023-12-19tee: optee: don't fail on services enumeration failureEtienne Carriere
Change optee probe function to only warn when service enumeration sequence fails instead of reporting an optee driver probe failure. Indeed U-Boot can still use OP-TEE even if some OP-TEE services are not discovered. Fixes: 94ccfb78a4d6 ("drivers: tee: optee: discover OP-TEE services") Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
2023-12-19remoteproc: k3-dsp: Avoid reloading of firmwareUdit Kumar
DSP core is going into abnormal state when load callback is called after starting of DSP core. Reload of firmware needs core to be stopped first, followed by load. So avoid loading of firmware, when core is started. Signed-off-by: Udit Kumar <u-kumar1@ti.com>
2023-12-19arm: vexpress64: juno: Allow boot from VirtIORobert Catherall
The AEM and Juno FVPs (Fixed Virtual Platforms) support a VirtIO disc interface. Adding VIRTIO to the list of boot devices allows these FastModel platforms to boot from 'disc' in the same way the hardware counterpart can boot from SATA or USB. This is a NOP if CONFIG_CMD_VIRTIO is not enabled, so no impact on Juno hardware (which is built with vexpress_aemv8a_juno_defconfig) Signed-off-by: Robert Catherall <robert.catherall@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2023-12-18Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-riscv ↵Tom Rini
into next - VisionFive2: Enable CONFIG_SYSRESET - StarFive: Modify starfive timer driver - AMD/Xilinx: Add MicroBlaze V support - Unmatched: Migrate to text environment
2023-12-18Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-spi ↵Tom Rini
into next - spi_nor_read_sfdp_dma_unsafe (Vaishnav) - w25q01/02 (Jim)
2023-12-18Merge tag 'v2024.01-rc5' into nextTom Rini
Prepare v2024.01-rc5
2023-12-18Prepare v2024.01-rc5v2024.01-rc5Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2023-12-18riscv: sifive: unmatched: migrate to text environmentYong-Xuan Wang
Migrate to the new environment format and drop most of the config.h. Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2023-12-18timer: starfive: Add Starfive timer supportKuan Lim Lee
Add timer driver in Starfive SoC. It is an timer that outside of CPU core and inside Starfive SoC. Signed-off-by: Kuan Lim Lee <kuanlim.lee@starfivetech.com> Signed-off-by: Wei Liang Lim <weiliang.lim@starfivetech.com> Changes for v2: - correct driver name, comment, variable Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2023-12-18riscv: Add support for AMD/Xilinx MicroBlaze VMichal Simek
MicroBlaze V is new AMD/Xilinx soft-core 32bit RISC-V processor IP. It is hardware compatible with classic MicroBlaze processor. The patch contains initial wiring and configuration for initial HW design with memory, cpu, interrupt controller, timers and uartlite console (interrupt controller is listed but U-Boot is not using it). Provided DT is just describing one configuration and should be taken only as example. Signed-off-by: Michal Simek <michal.simek@amd.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com> Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
2023-12-18configs: visionfive2: Enable CONFIG_SYSRESET configJaehoon Chung
Enable CONFIG_SYSRESET config to do reset. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2023-12-18riscv: dts: jh7110: Add a gpio-restart nodeJaehoon Chung
Add gpio-restart node to do reset. Before applied this patch, System Reset Extension doesn't appear with sbi command. OpenSBI 1.3 Machine: Vendor ID 489 Architecture ID 8000000000000007 Implementation ID 4210427 Extensions: sbi_set_timer sbi_console_putchar ...[snip]... IPI Extension RFENCE Extension Hart State Management Extension Performance Monitoring Unit Extension After applied this patch, System Reset Extension is supported from SBI. OpenSBI 1.3 Machine: Vendor ID 489 Architecture ID 8000000000000007 Implementation ID 4210427 Extensions: sbi_set_timer sbi_console_putchar ...[snip]... IPI Extension RFENCE Extension Hart State Management Extension System Reset Extension Performance Monitoring Unit Extension Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2023-12-17Merge tag 'efi-next-20231217' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-efi into next Pull request for efi-next-20231217 Documentation: * replace MD5 and SHA1 by SHA256 in examples UEFI: * Refactor boot manager and bootefi command to let the EFI boot method work without shell.
2023-12-17doc: Replace examples of MD5 and SHA1 with SHA256Sean Anderson
Both SHA1 and (especially) MD5 are no longer as safe as they once were for cryptographic use. Replaces examples which use them with examples using SHA256 instead. This will provide more-secure defaults for users who use documentation examples as a base for their own use. This is not too necessary for non-verified-boot scenarios (since someone could just replace the checksum), but I wanted to be complete. Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2023-12-17bootmeth: use efi_loader interfaces instead of bootefi commandAKASHI Takahiro
Now that efi_loader subsystem provides interfaces that are equivalent with bootefi command, we can replace command invocations with APIs. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2023-12-17cmd: efidebug: ease efi configuration dependencyAKASHI Takahiro
Now it is clear that the command actually depends on interfaces, not "bootefi bootmgr" command. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2023-12-17cmd: bootefi: move library interfaces under lib/efi_loaderAKASHI Takahiro
In the prior commits, interfaces for executing EFI binary and boot manager were carved out. Move them under efi_loader directory so that they can be called from other places without depending on bootefi command. Only efi_selftest-related code will be left in bootefi.c. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2023-12-17cmd: bootefi: localize global device paths for efi_selftestAKASHI Takahiro
Device paths allocated in bootefi_test_prepare() will be immediately consumed by do_efi_selftest() and there is no need to keep them for later use. Introduce test-specific varialbles to make it easier to move other bootmgr functions into library directory in the next commit. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2023-12-17cmd: bootefi: carve out binary execution interfaceAKASHI Takahiro
Carve binary execution code out of do_bootefi_image() in order to move binary-execution specific code into library directory in the later commit. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2023-12-17cmd: bootefi: carve out EFI boot manager interfaceAKASHI Takahiro
Carve EFI boot manager related code out of do_bootefi_image() in order to move boot manager specific code into library directory in the later commit. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
generated by cgit v1.2.3 (git 2.0.4) at 2025-08-06 14:49:55 +0000