summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2021-01-15arm: socfpga: soc64: Skip handoff data access in SSBLChee Hong Ang
SPL already setup the Clock Manager with the handoff data from OCRAM. When the Clock Manager's driver get probed again in SSBL, it shall skip the handoff data access in OCRAM. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
2021-01-15arm: socfpga: soc64: SSBL shall not setup stack on OCRAMChee Hong Ang
Since SSBL is running in DRAM, it shall setup the stack in DRAM instead of OCRAM which is occupied by SPL and handoff data. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
2021-01-15arm: socfpga: mailbox: Add 'SYSTEM_RESET' PSCI support to mbox_reset_cold()Chee Hong Ang
mbox_reset_cold() will invoke ATF's PSCI service when running in non-secure mode (EL2). Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
2021-01-15arm: socfpga: soc64: Add ATF support for FPGA reconfig driverChee Hong Ang
In non-secure mode (EL2), FPGA reconfiguration driver calls the SMC/PSCI services provided by ATF to configure the FPGA. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
2021-01-15arm: socfpga: soc64: Add ATF support for Reset Manager driverChee Hong Ang
In non-secure mode (EL2), Reset Manager driver calls the SMC/PSCI service provided by ATF to enable/disable the SOCFPGA bridges. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
2021-01-15net: designware: socfpga: Add ATF support for MAC driverChee Hong Ang
In non-secure mode (EL2), MAC driver calls the SMC/PSCI services provided by ATF to setup the PHY interface. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
2021-01-15mmc: dwmmc: socfpga: Add ATF support for MMC driverChee Hong Ang
In non-secure mode (EL2), MMC driver calls the SMC/PSCI services provided by ATF to set SDMMC's DRVSEL and SMPLSEL. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
2021-01-15mmc: dwmmc: Change designware MMC 'clksel' callback function to return statusSiew Chin Lim
Change 'clksel' callback function to allow the code to return a status. This patch is a preparation for enabling Arm-Trusted-Firmware (ATF) in Intel SoC FPGA. This patch does not change functionality. When using Arm-Trusted-Firmware (ATF) in Intel SoC FPGA, the MMC clock related register is secure register which is required to be written via SMC/PCSI call. It is possible that U-Boot fail to write the register if there is unexpected error between U-Boot and ATF. As a result, there maybe signal integrity on MMC connection due to clock. So, the code should reports error to user when 'clksel' fail. Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
2021-01-15arm: socfpga: Add secure register access helper functions for SoC 64bitsSiew Chin Lim
These secure register access functions allow U-Boot proper running at EL2 (non-secure) to access System Manager's secure registers by calling the ATF's PSCI runtime services (EL3/secure). Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2021-01-15arm: socfpga: soc64: Define SMC function identifiers for PSCI SiP servicesChee Hong Ang
This header file defines the Secure Monitor Call (SMC) message protocol for ATF (BL31) PSCI runtime services. It includes all the PSCI SiP function identifiers for the secure runtime services provided by ATF. The secure runtime services include System Manager's registers access, 2nd phase bitstream FPGA reconfiguration, Remote System Update (RSU) and etc. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
2021-01-15arm: socfpga: soc64: Add SMC helper function for Intel SOCFPGA (64bits)Chee Hong Ang
invoke_smc() allow U-Boot proper running in non-secure mode (EL2) to invoke SMC call to ATF's PSCI runtime services such as System Manager's registers access, 2nd phase bitstream FPGA reconfiguration, Remote System Update (RSU) and etc. smc_send_mailbox() is a send mailbox command helper function which invokes the ATF's PSCI runtime service (function ID: INTEL_SIP_SMC_MBOX_SEND_CMD) to send mailbox messages to Secure Device Manager (SDM). Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
2021-01-15arm: socfpga: Disable "spin-table" method for booting LinuxChee Hong Ang
Standard PSCI function "CPU_ON" provided by ATF is now used by Linux kernel to bring up the secondary CPUs to enable SMP booting in Linux on SoC 64bits platform. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
2021-01-15arm: socfpga: soc64: Override 'lowlevel_init' to support ATFChee Hong Ang
Override 'lowlevel_init' to make sure secondary CPUs trapped in ATF instead of SPL. After ATF is initialized, it will signal the secondary CPUs to jump from SPL to ATF waiting to be 'activated' by Linux OS via PSCI call. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
2021-01-15arm: socfpga: soc64: Load FIT image with ATF supportChee Hong Ang
Instead of loading u-boot proper image (u-boot.img), SPL now loads FIT image (u-boot.itb) which includes u-boot proper, ATF and u-boot proper's DTB. For OS, u-boot now loads FIT images (kernel.itb) which includes Linux Image and Linux's DTB. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
2021-01-15arm: socfpga: Add function for checking description from FIT imageChee Hong Ang
Add board_fit_config_name_match() for matching board name with device tree files in FIT image. This will ensure correct DTB file is loaded for different board type. Currently, we are not supporting multiple device tree files in FIT image therefore this function basically do nothing for now. Users are allowed to override this 'weak' function in their specific board implementation. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
2021-01-13Merge tag 'u-boot-stm32-20210113' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - Enable logging features for stm32mp15 boards - Update MAINTAINERS emails for STI and STM32 - Activate OF_LIVE for ST stm32mp15 boards - Switch to MCO2 for PHY 50 MHz clock for DHCOM boards - Correction in stm32prog command on uart: always flush DFU on start command - Update USB-C power detection algorithm on DK boards
2021-01-13Merge tag 'u-boot-amlogic-20210112' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - sync amlogic GX & AXG DT to Linux 5.10 - Add new MESON_EE driver support for GXBB & AXG - Add support for Libretech-CC v2, Wetek Core2, Beelink GT-King/Pro boards - add driver for TDO tl070wsh30 panel driver - meson: isolate loading of socinfo - Add soc_rev to environment - Enable G12A support for saradc - Add correct mmcdev on VIM3(L) & Odroid-N2(C4) - Read MAC from fuses for VIM3 & VIM3L boards
2021-01-13MAINTAINERS: Update STi and STM32 maintainers emails in remaining filesPatrice Chotard
A previous series already update STMicroelectronics emails maintainers but some files have been omitted (Makefile, .dts, .dtsi and .rst files). Update Patrick and my email address with the one dedicated to upstream activities. Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-01-13arm: stm32mp: stm32prog: always flush DFU on start command for uartPatrick Delaunay
Remove the test on data->dfu_seq, because dfu_seq=0 not only when the DFU is not started (mask with 0xffff). This flush is mandatory as the final treatment, common with USB, is done in DFU callback. This patch avoids issue if the received length is a multiple of the DFU packet. For example if size of bootfs partition is egual to 0x4000000, data->dfu_seq=0 at the end of the partition, the flush it not requested and the phase is not increased in the callback. U-Boot continue to request the bootfs in the next GetPhase command. Fixes: 468f0508b58b ("stm32mp: stm32prog: add serial link support") Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-01-13configs: stm32mp1: activate OF_LIVE for DT live supportPatrick Delaunay
Activate the live DT to reduce the DT parsing time. For example the boot time is reduced by 200ms on STM32MP157C-EV1 board for stm32mp15_basic_defconfig (boot with SPL) or stm32mp15_trusted_defconfig (boot with TF-A). Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-01-13ARM: dts: stm32: Switch to MCO2 for PHY 50 MHz clockMarek Vasut
The LAN8710i PHY currently uses 50 MHz clock direct from PLL4P. To permit PLL4P to run at faster frequency, use MCO2 as a divider. The PLL4P runs at 100 MHz, supplies MCO2 which divides it by 2 to 50MHz, and supplies the PHY with 50 MHz via pin PG2. The feedback clock are fed back in via pin PA1. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Change-Id: Ia9bf7119785d49b633a3ae761c3dc4a30b92628a
2021-01-13ARM: stm32: Use firmware property instead of loadablesMichal Simek
There shouldn't be a need to use loadables propertyn because u-boot can be pointed by firmware property. This change should also speedup boot process because loadables property is list of strings which code is going through. On the other hand firmware can just point to one image. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13board: stm32pm1: update USB-C power detection algorithm on DK boardsPatrice Chotard
USB-C power supply which are Power Delivery compliant (USB-PD) are able to provide different voltage/current (for example 5V/3A 9V/3A 12V/2.25A...) In this case, the power supply need to negotiate the voltage/current to use with the device using CC1/CC2 USB-C signals. If this negotiation occurs during ADC measurement (done also on CC1/CC2 USB-C signals) some ADC acquisition can be corrupted which cause wrong power supply current detection. To avoid this, the power supply current detection algorithm is updated as following: - perform an ADC measurement, if a 3A current is detected, continue the boot process. - else, wait 20ms (max tPDDebounce duration) to ensure that USB-PD negotiation is done and perform another ADC measurement. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2021-01-13configs: stm32mp15: enable LOG featuresPatrick Delaunay
Activate the logging features in SPL and U-Boot (CONFIG_LOG and CONFIG_SPL_LOG) and the command 'log' with CONFIG_CMD_LOG. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13board: st: common: migrate trace to dev and log macroPatrick Delaunay
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13board: st: stm32mp1: migrate trace to dev and log macroPatrick Delaunay
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13video: stm32_dsi: migrate trace to dev and log macroPatrick Delaunay
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13video: stm32_ltdc: migrate trace to dev and log macroPatrick Delaunay
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13serial: stm32: define LOG_CATEGORYPatrick Delaunay
Define LOG_CATEGORY to allow filtering with log command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13memory: stm32-fmc2: migrate trace to dev and log macroPatrick Delaunay
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13mtd: stm32_fmc2: migrate trace to dev and log macroPatrick Delaunay
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13spi: stm32_qspi: migrate trace to dev and log macroPatrick Delaunay
Change debug/pr_* to log_* or dev_* macro and define LOG_CATEGORY. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) or log macro (CONFIG_LOGF_FUNC). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13spi: stm32_spi: migrate trace to dev and log macroPatrick Delaunay
Change debug/pr_debug to log_debug or dev_dbg macro and define LOG_CATEGORY. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) or log macro (CONFIG_LOGF_FUNC). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13phy: stm32-usbphyc: migrate trace to dev and log macroPatrick Delaunay
Change pr_debug to log_debug or dev_dbg macro and define LOG_CATEGORY. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) or log macro (CONFIG_LOGF_FUNC). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13i2c: stm32f7_i2c: migrate trace to dev and log macroPatrick Delaunay
Change debug to dev_dbg macro and define LOG_CATEGORY. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) or log macro (CONFIG_LOGF_FUNC). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-01-13mailbox: stm32-ipcc: migrate trace to dev and log macroPatrick Delaunay
Change debug to dev_dbg macro and define LOG_CATEGORY. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) or log macro (CONFIG_LOGF_FUNC). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13reset: stm32-reset: migrate trace to dev and log macroPatrick Delaunay
Change debug to dev_dbg macro and define LOG_CATEGORY. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13clk: clk_stm32h7: migrate trace to dev and log macroPatrick Delaunay
Change debug and pr_ macro to dev macro and define LOG_CATEGORY. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) or log macro (CONFIG_LOGF_FUNC). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13clk: clk_stm32f: migrate trace to dev and log macroPatrick Delaunay
Change debug and pr_ macro to dev macro and define LOG_CATEGORY. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) or log macro (CONFIG_LOGF_FUNC). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13clk: stm32mp1: migrate trace to dev and log macroPatrick Delaunay
Change debug and pr_ macro to dev macro and define LOG_CATEGORY. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) or log macro (CONFIG_LOGF_FUNC). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13misc: rcc: keep the rcc device name for subnodePatrick Delaunay
Update the name associated with the RCC drivers to avoid duplicated name with the driver name. With this patch the traces displayed with log macro provide a correct device name. The rcc device name before the patch is: Class Index Probed Driver Name ----------------------------------------------------------- root 0 [ + ] root_driver root_driver simple_bus 0 [ + ] simple_bus |-- soc (...) nop 0 [ + ] stm32-rcc | |-- rcc@50000000 clk 0 [ + ] stm32mp1_clk | | |-- stm32mp1_clk reset 0 [ + ] stm32_rcc_reset | | `-- stm32_rcc_reset And they become: (...) nop 0 [ + ] stm32-rcc | |-- rcc@50000000 clk 0 [ + ] stm32mp1_clk | | |-- rcc@50000000 reset 0 [ + ] stm32_rcc_reset | | `-- rcc@50000000 The traces is correct: stm32mp1_clk rcc@stm32mp1_clk: ..... => stm32mp1_clk rcc@50000000: ..... Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13misc: rcc: migrate trace to dev macroPatrick Delaunay
Change debug and pr_err to dev macro and define LOG_CATEGORY. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13power: regulator: stm32-verfbuf: define LOG_CATEGORYPatrick Delaunay
Define LOG_CATEGORY to allow filtering with log command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13watchdog: stm32mp: migrate trace to dev macroPatrick Delaunay
Change debug and pr_err to dev macro and define LOG_CATEGORY. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13rtc: stm32: migrate trace to log macroPatrick Delaunay
Define LOG_CATEGORY to allow filtering with log command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13hwspinlock: stm32: migrate trace to log macroPatrick Delaunay
Define LOG_CATEGORY to allow filtering with log command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13timer: stm32: migrate trace to log macroPatrick Delaunay
Define LOG_CATEGORY to allow filtering with log command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13mmc: stm32_sdmmc2: migrate trace to dev and log macroPatrick Delaunay
Define LOG_CATEGORY, use dev_ macro when it is possible. Remove the "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) or log macro (CONFIG_LOGF_FUNC). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13ram: stm32mp1: migrate trace to dev or log macroPatrick Delaunay
Define LOG_CATEGORY, use dev_ macro when it is possible and migrate other trace to log_ macro. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13ram: stm32: migrate trace to log macroPatrick Delaunay
Define LOG_CATEGORY, change debug to dev_dbg and remove "%s:" __func__ header as it is managed by dev macro (dev->name is displayed) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
generated by cgit v1.2.3 (git 2.0.4) at 2025-08-07 06:03:44 +0000