| Age | Commit message (Collapse) | Author |
|---|
|
Add support for Gateworks System Controller pre-scaled ADC input.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
Add support for Gateworks System Controller fan tach input.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
The mxc_get_clock function is around for compatibility with older
drivers that are not clock aware. In this case asking for the clk for
MXC_CSPI_CLK does not take into account there are multiple SPI busses on
modern IMX SoC's and it will return the clock for the first bus which
may not be used or configured.
In the case you are not using the first bus you will not get the proper
clock. Fix this by obtaining the clock rate from the bus clock.
This resolves an invalid SPI clock frequency configuration for SPI2 on a
board where SPI1 is not used.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
First, thanks to Simon Glass and also Linaro, we now have access to a
few fast arm64 host machines in our Gitlab instance, to use as CI
runners. This series finishes the work that I pushed earlier and Simon
had started that enables arm64 hosts to be used for most things now.
The first notable change, especially if you use this on your own Gitlab
instance is that "DEFAULT_TAG" is now unused and we instead have:
- DEFAULT_ALL_TAG:
- DEFAULT_ARM64_TAG:
- DEFAULT_AMD64_TAG:
- DEFAULT_FAST_AMD64_TAG:
This lets us say that some jobs can be run on all runners, because they
are small enough that anything we'd connect to CI is fast enough and it
also does not depend on the underlying host architecture. Next we have
tags for any arm64 host, or any amd64 host. Finally, we have a tag for
fast amd64 hosts. What these last three are for is that we have a few
jobs that need to run on amd64 hosts and so we have to restrict them
there, but we also have now reworked the world build jobs to build
(almost) everything in a single job and on the fast amd64 machines this
is still as quick as the old way was, in practice.
To reach this point, we say that the Xtensa jobs can only run on amd64
hosts. Our targets only work with the binary-only toolchain and so this
is a reasonable limit and we exclude them from the world build jobs. We
also need to deal with ensuring the right toolchain is used regardless
what the host architecture is and that we don't use the host toolchain
by accident. Finally, because some of these changes needed to be worked
out in the linter, fix some of the general warnings that notes as well.
|
|
Bring us up to the current Ubuntu "Jammy" tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
First, try and be slightly clearer about what "buildx" is with respect
to the docker build process.
Second, now that we build the container for both amd64 and arm64, we
should document how to make a docker "builder" that has multiple nodes.
With this one node should be amd64 and one node arm64, and with
reasonably fast arm64 hardware this will be much quicker than using
QEMU.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We should always look in our downloaded toolchains first and then for
host-provided toolchains.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We do not want to use the host toolchain for building our platforms in
CI (it is both too old, and would be inconsistent with our CI
practices). To do this we need to set the toolchain-prefix so that we
don't end up guessing "/opt/.../aarch64-linux-aarch64-linux-" as the
prefix.
Link: https://source.denx.de/u-boot/custodians/u-boot-dm/-/issues/32
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In the test.py stage of the build we mark the pytest results as
artifacts to save, so that they can be used for reports. This however
leads to all of the artifacts being downloaded (and then not used) in
later stages. Optimize this out by using an empty list of dependencies
here (which is the keyword for which artifacts are needed).
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When validating our current pipeline, a warning is produced about a lack
of a default workflow. For how we use it, we can add a simple default of
"always".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
First, introduce DEFAULT_ALL_TAG, DEFAULT_ARM64_TAG, DEFAULT_AMD64_TAG
and DEFAULT_FAST_AMD64_TAG and remove the previous DEFAULT_TAG (as
anyone making use of that will need to adjust their jobs). This allows
us to say that some jobs can run on amd64 or arm64 hosts under the all
tag, while some jobs must run on amd64 (the Xtensa jobs due to
binary-only toolchains and sandbox for now) Then we rework the world
build stage to only run on our very fast amd64 hosts, or our arm64 hosts
(which are also very fast). This should result in a similar overall
build time but also a much more consistent overall build time as we
won't have the two big world jobs possibly run on our slower build
nodes.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove the rest of the places where we hard-code the version of the
toolchain we're using.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The xtensa architecture is interesting in that the platforms we support
are only valid on the binary-only toolchains as the DC233C instruction
set requires those toolchains (and not the FSF instruction set). Only
install the binary toolchain on amd64 hosts and only run the tests on
them as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This brings in assortment of updates to our python tooling, from Paul
HENRYS <paul.henrys_ext@softathome.com>
|
|
When specifying a directory containing DTBs with 'fit,fdt-list-dir', it can be
handy not to have to also specify this directory to the input directories of
binman with '-I' option and use the method tools.append_input_dirs() append it.
This avoids to have to specify the DTB directory in both the device tree
provided to binman and through '-I' option to binman.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
append_input_dirs() can be used to append a list of input directories to indir
global list.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This change allows to replace both 'SEQ' and 'NAME' keywords by respectively a
sequence number and the name of the FDT to provide more flexibility in the node
name for the device trees included in the FIT.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Input directories can be passed to binman using the '-I' option and those
input directories are now also passed to 'dtc' when run by binman.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
An optional list of input directories can be passed to EnsureCompiled() which
allows to pass a list of directories where input files can be searched.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Test the property 'fit,encrypt' to encrypt FIT data.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
|
|
mkimage can be used for both signing the FIT or encrypt its content and the
option '-k' can be used to pass a directory where both signing and encryption
keys can be retrieved. Adding 'fit,encrypt' property to the 'fit' node, leads to
try to find keys directory among binman include directories.
_get_priv_keys_dir() is renamed as _get_keys_dir() and adapted to support both
signing and encryption nodes in the FIT.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When the initialisation vector is randomly generated, its value shall be
stored in the FIT together with the encrypted data. The changes allow to
store the IV in the FIT also in the case where the key is not stored in
the DTB but retrieved somewhere else at runtime.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
For new PowerPC developments, it will be useful to borrow devicetrees
from Linux. This patch makes it possible.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
|
|
In generic_phy_get_bulk(), if 'phys' property is absent in
the device node then it is not an error condition.
Change print message verbosity to debug to avoid spamming
console in such cases.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
|
|
The current value of CONFIG_FASTBOOT_BUF_ADDR is incorrect for hardware
with 512MB and 1GB of RAM. The RAM address ranges for these devices are:
- 512MB:
- Start: 0x80000000
- End: 0xA0000000
- 1GB:
- Start: 0x80000000
- End: 0xC0000000
The current buffer address makes fastboot downloads work only on
hardware with 2GB of RAM.
To fix this issue:
1. Lower CONFIG_FASTBOOT_BUF_ADDR to 0x88200000. This makes the buffer
to be equal ot CONFIG_SYS_LOAD_ADDR, which is a safe address to
download files using fastboot.
2. Reduce the size of the download buffer to 128MB, avoiding overlaps
with RAMDISK_ADDR_R. This is a good enough value for individual
downloads.
These changes make fastboot downloads work with 512MB and 1GB devices.
Fixes: defe30a78b76 ("verdin-am62: add DFU, USB and UUU fastboot support")
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
Support of legacy 64-bit entry point was already present when booting a bzimage
with 'zboot' but not supported with 'bootm' when the x86_64 Linux kernel is
embedded in a FIT image.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Evgeny Bachinin <EABachinin@salutedevices.com> says:
This patch-set repairs ability to use sandbox with CONFIG_OF_EMBED=y.
For now, to use OF_EMBED, the following must be done
1) sandbox64_defconfig should have:
```
-CONFIG_OF_LIVE=y
+CONFIG_OF_EMBED=y
```
2) On sandbox when CONFIG_OF_EMBED=y, the u-boot process can't start
due to:
```
Bloblist at b000 not found (err=-2)
initcall failed at call 000000000011829c (err=-2: No such file or \
directory)
### ERROR ### Please RESET the board ###
```
So, it is natural desire to disable CONFIG_BLOBLIST just to test
sandbox with OF_EMBED=y (disable it one way or another):
```
config SANDBOX
- select BLOBLIST
+ select BLOBLIST if SOME_NON_EXISTING_OPTION
```
3) As a result, having such changes (CONFIG_OF_EMBED=y &&
CONFIG_BLOBLIST=n) leads to the link & run-time errors, being fixed
by this patch series.
Link: https://lore.kernel.org/r/20241202-sandbox_repair_of_embed-v1-0-05aff4b0ccf7@salutedevices.com
[trini: The final patch is dropped as no longer relevant with Simon's
rework to that function which is now applied.]
|
|
This series is from Simon Glass <sjg@chromium.org>.
It first corrects the test for checking if a bloblist could have come
from TPL and so we check for a device tree, and then changes the
argument order for board_fdt_blob_setup() to be more inline with our
usual argument ordering.
Link: https://lore.kernel.org/r/20241102174944.412088-1-sjg@chromium.org
|
|
Having CONFIG_OF_EMBED=y && CONFIG_BLOBLIST=n leads to the link
error:
```
ld: /tmp/ccwtRVty.ltrans28.ltrans.o:(.data.rel+0x4e8): undefined \
reference to `do_ut_bootm'
```
Fixes: fe158657a5b ("test: inconsistent bootm tests")
Signed-off-by: Evgeny Bachinin <EABachinin@salutedevices.com>
|
|
Having CONFIG_OF_EMBED=y && CONFIG_BLOBLIST=n leads to the link
error:
```
ld: /tmp/ccwtRVty.ltrans28.ltrans.o:(.data.rel+0x4b0): undefined \
reference to `do_ut_bloblist'
```
Fixes: 6ea5df39e8d ("test: Only enable bloblist test when supported")
Signed-off-by: Evgeny Bachinin <EABachinin@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Having CONFIG_OF_EMBED=y && CONFIG_BLOBLIST=n leads to the link
error:
```
ld: /tmp/ccRVty.ltrans40.ltrans.o: in function `lib_test_is_enabled':
test/lib/kconfig.c:24: undefined reference to \
`invalid_use_of_IF_ENABLED_INT'
ld: test/lib/kconfig.c:26: undefined reference to \
`invalid_use_of_CONFIG_IF_ENABLED_INT'
```
Fixes: 29784d62ede ("test: Add some tests for kconfig.h")
Signed-off-by: Evgeny Bachinin <EABachinin@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Having CONFIG_OF_EMBED=y && CONFIG_BLOBLIST=n leads to the link
error:
```
ld: /tmp/ccwtRVty.ltrans0.ltrans.o: in function `state_uninit':
arch/sandbox/cpu/state.c:508: undefined reference to `bloblist_finish'
```
Fixes: 1c52fcca72b ("sandbox: Write out bloblist when exiting")
Signed-off-by: Evgeny Bachinin <EABachinin@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This returns a devicetree and updates a parameter with an error code.
Swap it, since this fits better with the way U-Boot normally works. It
also (more easily) allows leaving the existing pointer unchanged.
No yaks were harmed in this change, but there is a very small code-size
reduction.
For sifive, the OF_BOARD option must be set for the function to be
called, so there is no point in checking it again. Also OF_SEPARATE is
defined always.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
[trini: Update total_compute]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The condition for receiving a bloblist from TPL is reversed. This was
only noticed are the other fixes landed. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
|
|
into next
CI: https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/23926
- Board: Support LicheeRV Nano
- Board: Support bananapi-f3
- Board: Switch to OF_UPSTREAM for StarFive JH7110
- Board: Add sdhci driver for TH1520 SoC
|
|
The FIT name in RISC-V Falcon mode should be different from that in
normal boot mode; it is called linux.itb. If the setting is missing
in common/spl, the normal boot file name will be used.
Signed-off-by: Randolph <randolph@andestech.com>
|
|
Add document for Banana Pi F3 board which based on SpacemiT's K1 SoC.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Signed-off-by: Huan Zhou <pericycle.cc@gmail.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
|
|
Add basic support for SpacemiT's Banana Pi F3 board.
Update the k1.dtsi align with mainline.
Note that the device tree files follow the mainline Linux source[1].
Links: https://patches.linaro.org/project/linux-serial/patch/20240730-k1-01-basic-dt-v5-8-98263aae83be@gentoo.org/ [1]
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Signed-off-by: Huan Zhou <pericycle.cc@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
|
|
Enable driver for DesignWare MSHC. TH1520 supports all
speed modes up to HS400ES and UHS SDR105.
Also enable ADMA and mmc command.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
|
|
Add SDHCI and EMMC controlles nodes on TH-1520 SoC. And enable them for
Lichee module 4A.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
|
|
Add support for DesignWare SDHCI host controller on Alibaba TH1520 SoC
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
The imply statements should be sorted in the sequence
of appearance in .config.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
Get product ID and the other information from EEPROM, use them to select
the correct DTB.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
The prefix "SPL_" is not needed when using CONFIG_IS_ENABLED().
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fixes: 5ecf9b0b8a75 ("board: starfive: add StarFive VisionFive v2 board support")
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
Support multiple DTBs for JH7110 based boards, so they can
select the correct DT at runtime.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
So JH7110 based boards can select their own DT at runtime.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
As OF_UPSTREAM is implemented, these code are redundant.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
To support the other JH7110 based boards, add u-boot
device tree for them.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: H Bell <dmoo_dv@protonmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
To support JH7110 based boards besides v1.3B,
add a common dtsi and add common code to it.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
There are difference between upstream DT and the old DT
in terms of reg base, reset gpio and syscon. Make the driver
compatible with upstream DT.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
