| Age | Commit message (Collapse) | Author |
|---|
|
Enable PCIe/NVMe support. Also, enable the reset
driver which is a prerequisite for PCIe support.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
Add support for the IMX8MM SoC by adding driver data with the compatible
string of the GPR controller.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
Add support for PCIe clocks required to enable PCIe support on
iMX8MM SoC.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Remove not needed variables from environment and include config files.
- setup variable used to be executed from some bootscript, however
it's not required and there is no point on having this small helper
here
- boot_file, kernel_file, ip_dyn variables are not used anywhere
- fdt_fixup variable is just set empty
- defargs, vidargs variables used to be used from some bootscript,
however there is no point on having it here and even old legacy
bootscript can work without them
- removed CONFIG_ENABLE_DDR_TRAINING_DEBUG, this is a leftover from
some copy/paste
On colibri imx6ull/imx7 NAND module, remove consoleblank=0, this is
already the Linux kernel default therefore useless.
Various Linux Kernel command line options removed are not-existing
left-over that applied to some old NXP i.MX downstream branch
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
Enable ipv6, wget, and tftpput support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
The GW73xx baseboard needs a PCI dt adjustment for revC/D based on a
change of the PCIe switch. Make sure we are only doing this for a pci
based ethernet to avoid causing a boot hang when the ethernet1 alias
points to eqos or fec. To know this is a pcie device ensure the alias
begins with the pcie controller.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
In Linux, we allow sleep moci to be turned off when the carrier board
supports it and the system is in suspend. In U-Boot, however, we want
the sleep moci to be always on. So we use a gpio hog and disable the
regulator. This change is necessary because we switched to upstream
device tree files with commit 23fe2def1edf
("verdin-imx8mm/verdin-imx8mp: move imx verdins to OF_UPSTREAM"). A
recent upstream patch removes the gpio hog from the Linux device tree,
so we need to add it to the u-boot dtsi. The following patch will remove
the gpio hog from the Linux device tree:
https://lore.kernel.org/linux-devicetree/20240405160720.5977-1-eichest@gmail.com/
The U-Boot patch can be applied without it and will not break the build.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
|
|
The following information printed on every boot is not very
helpful for the users:
SOC: 0xa0009300
LC: 0x40040
Move them to debug() level.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Mathieu Othacehe <othacehe@gnu.org>
|
|
Enable support for TPM2 devices. As the ATTPM20P TPM2 used on the
Gateworks Venice boards hangs off the SPI bus we enable SPI support
as well.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
MP1:
_ Add OHCI HCD support for STM32MP15xx DHSOM
_ Report OTP-CLOSED instead of rev.? on closed STM32MP15xx
_ Initialize TAMP_SMCR BKP..PROT fields on STM32MP15xx
_ Jump to ep on successful resume in PSCI suspend code
_ Add FASTBOOT support for STM32MP13
_ Fix/Rework key and leds management for STM32MP13/15
_ net: dwc_eth_qos: Clean up STM32 glue code and add STM32MP13xx support
MP2:
_ Add stm32-fmc-ebi support
_ Add: sdmmc2 support and fix AARCH64 compilation
|
|
https://source.denx.de/u-boot/custodians/u-boot-dfu
u-boot-dfu-20240419
- new "fastboot oem board" command
|
|
The blue led is used to indicate U-Boot entering / exit indication
then Linux heartbeat.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use led node's name instead for
u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Add compatible = "gpio-leds"; which is not present in kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Add 2 gpio-keys :
_ button-user-1 for stm32prog mode activation.
_ button-user-2 for fastboot mode activation.
Remove proprietary st,fastboot-gpios and st,stm32prog-gpios.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
The blue led is used to indicate U-Boot entering / exit indication
then Linux heartbeat.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use led node's name instead for
u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Add compatible = "gpio-leds" which is not present in kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Add 2 gpio-keys :
_ button-user-1 for stm32prog mode activation.
_ button-user-2 for fastboot mode activation.
Remove proprietary st,fastboot-gpios and st,stm32prog-gpios.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Instead of using "st,fastboot-gpios" and "st,stm32prog-gpios", declare
2 gpio-keys.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename "red" led node's name to "led-red".
Remove status property which is useless.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Instead of using "st,fastboot-gpios" and "st,stm32prog-gpios", declare
2 gpio-keys.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Remove "color" property from led-red node which is not supported
by U-Boot.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
led-red and button dedicated to fastboot share the same gpio GPIOA13.
led-blue and button dedicated to stm32prog share the same gpio GPIOA14.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from led-red and
led-blue led's node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Add 2 gpio-keys :
_ button-user-1 for stm32prog mode activation.
_ update button-user's label (defined in kernel DT) to match label
requested in board_key_check() for fastboot mode activation.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Instead of using gpio directly to detect key pressed on button
dedicated for fastboot and stm32mprog, make usage of BUTTON UCLASS.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
|
|
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Enable FASTBOOT relative flags for stm32mp13_defconfig.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
|
|
When building with AARCH64 defconfig, we got warnings, fix them.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Add compatible used for STM32MP25 family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a58c ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a58c ("arm: dts: stm32: Add partitions in flash0 and nand node for
stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Fix flash@0 and nand@0 partition node name with correct offset.
Fixes: e91d3c61767b ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-ev1")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
In case of an OTP-CLOSED STM32MP15xx system, the CPU core 1 cannot be
released from endless loop in BootROM only by populating TAMP BKPxR 4
and 5 with magic and branch address and sending SGI0 interrupt from
core 0 to core 1 twice. TAMP_SMCR BKP..PROT fields must be initialized
as well to release the core 1 from endless loop during the second SGI0
handling on core 1. Initialize TAMP_SMCR to protect the first 32 backup
registers, the ones which contain the core 1 magic, branch address and
boot information.
This requirement seems to be undocumented, therefore it was necessary
to trace and analyze the STM32MP15xx BootROM using OpenOCD and objdump.
Ultimately, it turns out that a certain BootROM function reads out the
TAMP_SMCR register and tests whether the BKP..PROT fields are non-zero.
If they are zero, the BootROM code again waits for SGI0 using WFI, else
the execution moves forward until it reaches handoff to the TAMP BKPxR 5
branch address.
This fixes CPU core 1 release using U-Boot PSCI implementation on an
OTP-CLOSED system, i.e. system with fuse 0 bit 6 set.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
SoC revision is only accessible via DBUMCU IDC register,
which requires BSEC.DENABLE DBGSWENABLE bit to be set to
make the register accessible, otherwise an access to the
register triggers bus fault. As BSEC.DBGSWENABLE is zero
in case of an OTP-CLOSED system, do NOT set DBGSWENABLE
bit as this might open a brief window for timing attacks.
Instead, report that this system is OTP-CLOSED and do not
report any SoC revision to avoid confusing users. Use an
SEC/C abbreviation to avoid growing SOC_NAME_SIZE .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The source file is in arch/arm/mach-stm32mp/ecdsa_romapi.c and not
in arch/arm/mach-stm32mp/stm32mp1/ecdsa_romapi.c . There are two
Makefile entries in each subdirectory. Drop the bogus one and keep
only the correct one, the one in arch/arm/mach-stm32mp/Makefile .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
In case the system has resumed successfully, the PSCI suspend resume
code has to jump to the 'ep' successful resume entry point code path,
otherwise the code has to jump to content of the LR register, which
points to failed resume code path.
To implement this distinction, rewrite LR register stored on stack
with 'ep' value in case of a successful resume, which is really in
every case unless some catastrophic failure occurred during suspend.
Without this change, Linux counts every resume as failed in
/sys/power/suspend_stats/fail
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The "st,ext-phyclk" property is a unification of "st,eth-clk-sel"
and "st,eth-ref-clk-sel" properties. All three properties define
ETH CK clock direction, however:
- "st,eth-clk-sel" selects clock direction for GMII/RGMII mode
- "st,eth-ref-clk-sel" selects clock direction for RMII mode
- "st,ext-phyclk" selects clock direction for all RMII/GMII/RGMII modes
The "st,ext-phyclk" is the preferrable property to use.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
|
|
Add compatible "st,stm32mp13-dwmac" to manage STM32MP13 boards.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Rebase, reshuffle, squash code
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
|
|
Manage 2 ethernet instances, select which instance to configure with mask
If mask is not present in DT, it is stm32mp15 platform.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Rework the code
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
|
|
Use const bool for the values parsed out of DT. Drop the duplicate
assignment of false into those bool variables, assign them directly
with the content parsed out of DT. Abbreviate the variable name too.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Use dev_*() only to print all the logs from this glue code,
instead of mixing dev_*(), log_*(), pr_*() all in one code.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
|
