summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2021-06-23arm64: zynqmp: Add reset description for sataMichal Simek
Sata needs to get reset before configuration that's why add property for it there. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23arm64: zynqmp: Add missing SMID for pcie to zynqmp.dtsiStefano Stabellini
The SMMU is disabled in device tree so this change has no impact. The benefit is that this way it is in sync with xen.dtsi. Xen enables the SMMU and makes use of it. Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
2021-06-23arm64: zynqmp: Disable CCI by defaultMichal Simek
There is no reason to have CCI no enabled by default. Enable it when your system configuration requires it. In Xilinx configuration flow this is work for Device Tree Generator which reads information from HW Design configuration. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23arm64: zynqmp: Update psgtr clocks index for boardsMichal Simek
Update the psgtr clock indexing for couple of zynqmp boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23arm64: zynqmp: Handle MMC seq number based on boot deviceMichal Simek
K26 has EMMC and SD and default 0 is not working when system is booting out of SD which is controller 1. Add controller autodetection via mmc_get_env_dev(). The same code is used for distro_boot selection done in board_late_init(). bootseq variable can't be reused because this is called so late. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23arm64: zynqmp: Add psu_init_gpl for k26 boardsMichal Simek
Add psu_init_gpl file for getting SPL to work directly from the tree. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23ARM: zynq: Rename bus to be align with simple-bus yamlMichal Simek
Rename amba to AXI. Based on Xilinx Zynq TRM (Chapter 5) chip is "AXI point-to-point channels for communicating addresses, data, and response transactions between master and slave clients. This ARM AMBA 3.0..." Issues are reported as: .. amba: $nodename:0: 'amba' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$' >From schema: ../github.com/devicetree-org/dt-schema/dtschema/schemas/simple-bus.yaml Similar change has been done for Xilinx ZynqMP SoC. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/8a4bc80debfbb79c296e76fc1e4c173e62657286.1606397101.git.michal.simek@xilinx.com
2021-06-23arm64: zynqmp: Enable gpio driver for zcu1275/zcu1285Michal Simek
Enable gpio driver on these boards. GPIOs can be used on any board. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23arm64: zynqmp: Add support for SVD devicesMichal Simek
SVDs are using different name which can't be handled via zynqmp_devices structure. That's why introduce zynqmp_detect_svd_name() which checks ID code for these devices and show proper name for them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23arm64: zynqmp: Enable EFI secure bootMichal Simek
Enabling EFI secure boot which is required for EBBR specification. Enabling this will fix "RT.SetVariable - Create one Time Base Auth Variable, the expect return status should be EFI_SUCCESS" Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23arm64: xilinx: Set CONFIG_ZYNQMP_FIRMWARE config for mini emmcT Karthik Reddy
CONFIG_ZYNQMP_FIRMWARE enables zynqmp firmware driver. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
2021-06-23arm64: zynqmp: Fix application loading on R5 core1Ashok Reddy Soma
From U-Boot, loading application on RPU core 0 is fine but loading on core 1 is not handled properly. Lock-step mode needs both the R5 cores to be initialized and it is working fine. Whereas in SPLIT mode individual R5 cores needs to be initialized as they need to execute differenet applications. Handle both these lock-step and split modes by propagating mode and RPU core number(4 for RPU0 and 5 for RPU1) for various functions and by adding conditions in those functions. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23ARM: zynq: Fix OCM mapping to be aligned with binding on zc702Michal Simek
The Linux commit f69629919942 ("dt-bindings: sram: Convert SRAM bindings to json-schema") converted binding to yaml and some missing required properties started to be reported. Align binding based on it. The patch is fixing these warnings: .../zynq-zc702.dt.yaml: sram@fffc0000: '#address-cells' is a required property .../zynq-zc702.dt.yaml: sram@fffc0000: '#size-cells' is a required property .../zynq-zc702.dt.yaml: sram@fffc0000: 'ranges' is a required property >From schema: .../Documentation/devicetree/bindings/sram/sram.yaml Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/87c02786ccd8d7827827a9d95a8737bb300caeb0.1606397101.git.michal.simek@xilinx.com
2021-06-23ARM: zynq: Convert at25 binding to new description on zc770-xm013Michal Simek
The Linux commit f8f79fa6bb25 ("dt-bindings: at25: convert the binding document to yaml") converted binding to yaml and 3 deprecated properties pop up. The patch is fixing these warnings: .../zynq-zc770-xm013.dt.yaml: eeprom@2: 'pagesize' is a required property .../zynq-zc770-xm013.dt.yaml: eeprom@2: 'size' is a required property .../zynq-zc770-xm013.dt.yaml: eeprom@2: 'address-width' is a required property >From schema: .../Documentation/devicetree/bindings/eeprom/at25.yaml by converting them to new binding. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/be2c1125d98386033e182012eb08986924707a76.1606397101.git.michal.simek@xilinx.com
2021-06-23zynqmp: spl: support DRAM ECC initializationJorge Ramirez-Ortiz
Use the ZDMA channel 0 to initialize the DRAM banks. This avoid spurious ECC errors that can occur when accessing unitialized memory. The feature is enabled by setting the option CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT and providing the following data: SPL_ZYNQMP_DRAM_BANK1_BASE: start of memory to initialize SPL_ZYNQMP_DRAM_BANK1_LEN : len of memory to initialize (hex) SPL_ZYNQMP_DRAM_BANK2_BASE: start of memory to initialize SPL_ZYNQMP_DRAM_BANK2_LEN : len of memory to initialize (hex) Setting SPL_ZYNQMP_DRAM_BANK_LEN to 0 takes no action. Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23gpio: pca953x: Add missing i2c dependencyMichal Simek
pca953x also depends on i2c that's why add dependency to Kconfig. Where GPIO is enabled but I2C compilation error pops up. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-06-22Makefile: Adjust indention of GENENV quiet outputJan Kiszka
The column width for a command name is 8. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2021-06-22autoboot: fix typos of CONFIG_AUTOBOOT_USE_MENUKEYDa Xue
Replace typo CONFIG_USE_AUTOBOOT_MENUKEY with CONFIG_AUTOBOOT_USE_MENUKEY as when they were introduced initially there was some mismatch in which name was used where. Fixes: 8fc31e23aa83 ("autoboot: Rename CONFIG_MENUKEY to CONFIG_AUTOBOOT_MENUKEY") Signed-off-by: Da Xue <da@libre.computer>
2021-06-22disk/part_dos.c: Fix a variable typo in write_mbr_partitions()Christian Melki
This function is passed *dev not *dev_desc, so pass the right name to part_init(). Fixes: f14c5ee5ab8b ("disk: part_dos: update partition table entries after write") Signed-off-by: Christian Melki <christian.melki@t2data.com>
2021-06-22azure: Use msys2 20210604 installer for Windows buildBin Meng
MSYS2 Windows build started to fail since yesterday (Jun 21): checking keyring... checking package integrity... error: gcc-libs: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust :: File /var/cache/pacman/pkg/gcc-libs-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)). error: gcc: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust :: File /var/cache/pacman/pkg/gcc-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)). error: failed to commit transaction (invalid or corrupted package) Errors occurred, no packages were upgraded. Switching to the latest installer (version 20210604) seems to fix it. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by: Tom Rini <trini@konsulko.com>
2021-06-22mtd: spi-nor-ids: Add Macronix MX66UW2G345Gzhengxun
The MX66UW2G345G is Macronix Flash with SINGLE and OCTAL I/O. Hence, add SPI_NOR_OCTAL_READ flag for this flash. Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> [jagan: change order of id flags] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: zhengxun <zhengxunli.mxic@gmail.com>
2021-06-22Revert "mmc: fsl_esdhc_imx: use VENDORSPEC_FRC_SDCLK_ON to control card ↵Fabio Estevam
clock output" This reverts commit 63756575b42b8b4fb3f59cbbf0cedf03331bc2d2. Since this commit a imx6qdl-pico board boots extremely slowly in both SPL as well as U-Boot proper. Fix this regression by reverting the offending commit for now. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com>
2021-06-22mmc: mmc-uclass: change to static about dm functionJaehoon Chung
Change to static about dm function. They can be used with wrapper functions. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-06-22mmc: fsl_esdhc_imx: use mmc_send_cmd instead of dm_mmc_send_cmdJaehoon Chung
Use mmc_send_cmd instead of dm_mmc_send_cmd. It doesn't need to distinguish this function. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-06-22mmc: Update environment variable with active partitionReuben Dowle
This patch allows uboot scripts make choices about where to boot from based on the active mmc boot partition. This allows having two copies of kernel, filesystems etc, and choosing which to boot from based off of the active bootloader partition. Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-06-22mmc: dwmmc: socfpga: Get "fifo-mode" property from DTLey Foon Tan
Add FIFO mode support for SoCFPGA dwmmc, read "fifo-mode" property from DT. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-06-22mmc: dw_mmc: Fixes data read when receiving DTO interrupt in FIFO modeLey Foon Tan
The data read is not working when using FIFO mode. From DesignWare databook, when a Data_Transfer_Over (DTO) interrupt is received, the software should read the remaining data from FIFO. Add DTO interrupt checking on data read path and clear interrupts before start reading from FIFO. So, it doesn't clear the next pending interrupts unintentionally after read from FIFO. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-06-22mmc: mtk-sd: increase the minimum bus frequencyWeijie Gao
With a 48MHz input clock, the lowest bus frequency can be as low as 48000000 / (4 * 4095) = 2930Hz. Such an extremely low frequency will cause the mmc framework take seconds to finish the initialization. Limiting the minimum bus frequency to a slightly higher value can solve the issue without any side effects. Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-06-21ARM: dts: k3-j7200-common-proc-board-u-boot.dtsi: Fix dtc warningsVignesh Raghavendra
Fix following dtc warning by explicitly setting up #size-cells and #address-cells when overriding node in -u-boot.dtsi arch/arm/dts/k3-j7200-common-proc-board.dtb: Warning (reg_format): /bus@100000/bus@28380000/mcu-navss/ringacc@2b800000:reg: property has invalid length (80 bytes) (#address-cells == 2, #size-cells == 1) Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2021-06-21imx8mm: configs: enable distro default featuresAndrey Zhizhikin
imx8mm ekv has been switched to use distro boot commands, but had no correct options enabled to support sysboot. According to the README.distro, sysboot is consindered to be a recommended way of using distro boot commands, it required default distro features to be enabled instead of only those that are relevant to the boot script. Replace the boot script specific options in the config to a default distro option. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Cc: Peng Fan <peng.fan@nxp.com> Fixes: 2df8930bf9 ("imx8mm: configs: add support for distro boot commands") Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-06-21imx8mp: configs: enable distro default featuresAndrey Zhizhikin
imx8mp ekv has been switched to use distro boot commands, but had no correct options enabled to support sysboot. According to the README.distro, sysboot is consindered to be a recommended way of using distro boot commands, it required default distro features to be enabled instead of only those that are relevant to the boot script. Replace the boot script specific options in the config to a default distro option. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Cc: Peng Fan <peng.fan@nxp.com> Fixes: 9b162b1d1f ("imx8mp: configs: add support for distro boot commands") Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-06-21o4-imx-nano: Fix dtc warningsFabio Estevam
Remove the LED unit addresses and reg properties to fix the following dtc build warnings: arch/arm/dts/o4-imx-nano.dtb: Warning (reg_format): /leds/led@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ... arch/arm/dts/o4-imx-nano.dtb: Warning (avoid_default_addr_size): /leds/led@0: Relying on default #address-cells value Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Oleh Kravchenko <oleg@kaa.org.ua>
2021-06-19Merge tag 'u-boot-rockchip-20210618' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-rockchip into next - New SoC platform support: rk3568; - rockchip pcie Code compile issue fix; - Board fix for rk3399 Khadas Edge; - Add Rockchip NFC driver;
2021-06-18Merge tag 'u-boot-stm32-20210618' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-stm into next - stm32mp157c-odyssey-som DT fixes - stm32_qspi: Fix short data write operation - dfu: set max_buf_size to erasesize also for NOR devices - Fixes ethernet clock property name for STM32MP1 board - STM32CubeProgrammer: various fixes - clk: cosmetic update for clk-uclass
2021-06-18Merge branch 'network_master' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-net
2021-06-18net: octeontx: smi: use dt live tree APITim Harvey
clean up octeontx_smi_probe by using the live-tree API. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-06-18cmd: pxe_utils: sysboot: fix crash if either board or soc are not set.Dimitri John Ledkov
If the environment does not have "soc" or "board" set, and fdtdir option is specified in extlinux.conf, the bootloader will crash whilst dereferencing a null pointer. Add a guard against null soc or board. Fixes a crash of qemu-riscv64_smode configuration, which does not have CONFIG_SYS_SOC defined. Signed-off-by: Dimitri John Ledkov <xnox@ubuntu.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-06-18net: use the same alias stem for ethernet as linuxMichael Walle
Linux uses the prefix "ethernet" whereas u-boot uses "eth". This is from the linux tree: $ grep "eth[0-9].*=.*&" arch/**/*dts{,i}|wc -l 0 $ grep "ethernet[0-9].*=.*&" arch/**/*dts{,i}|wc -l 633 In u-boot device trees both prefixes are used. Until recently the only user of the ethernet alias was the sandbox test device tree. This changed with commit fc054d563bfb ("net: Introduce DSA class for Ethernet switches"). There, the MAC addresses are inherited based on the devices sequence IDs which is in turn given by the device tree. Before there are more users in u-boot and both worlds will differ even more, rename the alias prefix to "ethernet" to match the linux ones. Also adapt the test cases and rename any old aliases in the u-boot device trees. Cc: David Wu <david.wu@rock-chips.com> Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-06-18net: use a more deterministic approach to get the active ethernet deviceMichael Walle
If the environment variable "ethact" is not set, the first device in the uclass is returned. This depends on the probing order of the ethernet devices. Moreover it is not not configurable at all. Try to return the ethernet device with sequence id 0 first which then can be configured by the aliases in a device tree. Fall back to the old mechanism in case of an error. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-06-18net: sun8i-emac: fix MDIO frequencyHeinrich Schuchardt
Commit 4f0278dac56a ("net: sun8i-emac: Lower MDIO frequency") leads to network failure on the OrangePi PC. => dhcp sun8i_emac_eth_start: Timeout According to the commit message the change of the MDIO frequency is only required for external PHYs. Fixes: 4f0278dac56a ("net: sun8i-emac: Lower MDIO frequency") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-06-18net: synquacer: Add netsec driverJassi Brar
Add SynQuacer's NETSEC GbE controller driver. Since this driver will load the firmware from SPI NOR flash, this depends on CONFIG_SYNQUACER_SPI=y. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-06-18net: dwc_eth_qos: Revert some changes of commit 3a97da12ee7bDaniil Stas
Revert some changes of commit 3a97da12ee7b ("net: dwc_eth_qos: add dwc eqos for imx support") that were probably added by mistake. One of these changes can lead to received data corruption (enabling FUP and FEP bits). Another causes invalid register rxq_ctrl0 settings for some platforms. And another makes some writes at unknown memory location. Fixes: 3a97da12ee7b ("net: dwc_eth_qos: add dwc eqos for imx support") Signed-off-by: Daniil Stas <daniil.stas@posteo.net> Cc: Ye Li <ye.li@nxp.com> Cc: Fugang Duan <fugang.duan@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-06-18net: dwc_eth_qos: Fix needless phy auto-negotiation restartsDaniil Stas
Disabling clk_ck clock leads to link up status loss in phy, which leads to auto-negotiation restart before each network command execution. This issue is especially big for PXE boot protocol because of auto-negotiation restarts before each configuration filename trial. To avoid this issue don't disable clk_ck clock after it was enabled. Signed-off-by: Daniil Stas <daniil.stas@posteo.net> Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-06-18net: e1000: do not attempt to set hwaddr for i210 without FLASHTim Harvey
commit f1bcad22dd19 ("net: e1000: add support for writing to EEPROM") adds support for storing hwaddr in EEPROM however i210 devices do not support this and thus results in errors such as: Warning: e1000#0 failed to set MAC address' Check if a flash device is present and if not return -ENOSYS indicating this is not supported. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-06-18Fix a memory leak issue in the RX port initialization.Hou Zhiqiang
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-06-18clk: cosmetic change in uclassPatrick Delaunay
Remove the tab in clk_get_bulk to respect the coding rules. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-06-18stm32mp: stm32prog: handle dfu errorPatrick Delaunay
Handle DFU stack error in STM32CubeProgrammer protocol. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-06-18dfu: add error callbackPatrick Delaunay
Add error callback in dfu stack to manage some board specific behavior on DFU targets. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-06-18stm32mp: stm32prog: change one message level to debugPatrick Delaunay
Move the message "Invalid or missing layout file." to debug level as it is a normal behavior and not an error and add the missing '\n'. This patch avoids the strange trace : Boot over usb0! Invalid or missing layout file.DFU alt info setting: done Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-06-18stm32mp: stm32prog: use get_cpu_dev for GetID commandPatrick Delaunay
Use get_cpu_dev() in uart getID command and remove the defines DEVICE_ID_BYTE1 and 2 defines. This patch prepare the support for new SOC family. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
generated by cgit v1.2.3 (git 2.0.4) at 2025-08-02 07:25:38 +0000