| Age | Commit message (Collapse) | Author |
|---|
|
On i.MX9 platforms, when booting from USB, the U-Boot environment is
always assumed to be in RAM. However, this causes the boot to hang when
`CONFIG_ENV_IS_NOWHERE` is not enabled. The boot also hangs even if the
environment is present in another storage media (for example, eMMC). Fix
the issue by correctly handling the U-Boot environment's location when
booting from USB. Also for i.MX95, set the environment location based on
the ENV config and not solely based on the boot device type.
Suggested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
|
|
unsupported layout"
Martin Schwan <m.schwan@phytec.de> says:
This series fixes a segfault, that would occur at the end of scanning a
device, which does not contain the required partition layout scheme for
a RAUC system.
With this series, a "bootflow scan" should now correctly scan the
specified devices with boot method "rauc" without crashing on invalid
partition schemes.
Link: https://lore.kernel.org/r/20250813-wip-bootmeth-rauc-priv-free-v1-0-1ef928169469@phytec.de
|
|
The private data struct can be freed when loading the boot script, as we
don't need the slot information anymore at this point.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Move freeing a distro_rauc_priv struct to a new, separate function for
better reuse.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Don't null bootflow->bootmeth_priv, as the private struct is freed later
on by the bootflow.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Fix a segfault when cleaning up the slots from the private struct. This
fault was generated by accessing a member of a null pointer.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
|
|
- DRAM controller driver off-by-one error fix.
|
|
In dbsc5_read_vref_training the arrays dvw_min_byte0_table and
dvw_min_byte1_table have 128 elements per channel. The variable
vref_stop_index is limited to be a maximum of 128. This means that the
index used to access the arrays must use a test of '< vref_stop_index'
rather than '<= vref_stop_index' in order to prevent out of bounds
accesses to the arrays.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Pull request net-20250818.
This is mostly code cleanup and fixes, mainly for issues reported by the
Smatch tool, plus two small features for NET_LWIP as well as support for
the BCM54612E phy.
net-common:
- Fix a bunch of issues reported by Smatch
- Introduce CONFIG_DNS
- Add support for BCM54612E phy
net-legacy:
- Add missing SPDX-License-Identifier for files originating from LiMon
net-lwip:
- ping: initialize net_try_count to 1
- sntp: remove redundant sys_check_timeouts()
- tftp: resend initial request
- Add Kconfig option to show ICMP unreachable errors
|
|
In cdns_torrent_phy_probe the test for too many lanes configured does
not set an error code before taking the error path. This could lead to a
silent failure if the calling code does not detect the error. Add the
code to return -EINVAL in this case.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
In cdns_sierra_pll_bind_of_clocks the variable 'i' is declared but never
assigned to before its value is used in a dev_err. Replace clk_names[i]
by the name passed to device_bind(), i.e., "pll_mux_clk". With that, the
clk_names[] array is unused and can therefore be removed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
[jf: update description]
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
|
|
In ks8851_mll_detect_chip the if..else code detects the case of (val &
0xfff0) != CIDER_ID and returns if found. So testing for this again will
always fail and the code is unreachable. Just remove the test and code
block.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
The legacy network stack sets net_try_count to 1 at the beginning of the
net_loop() function. This is required for net_start_again() to work
properly. Therefore, set the variable accordingly in the do_ping()
function when NET_LWIP=y. This fixes an issue where a ping to an
unreachable destination would run twice on the same network device. For
example with qemu_arm64_lwip_defconfig:
=> dhcp
DHCP client bound to address 10.0.2.15 (3 ms)
=> ping 10.0.0.1
Using virtio-net#32 device
ping failed; host 10.0.0.1 is not alive
Using virtio-net#32 device
ping failed; host 10.0.0.1 is not alive
=> QEMU: Terminated
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
|
|
In ca_phy_probe when checking for an external phy it uses a field from
the internal phy due to what is assumed to be a copy/paste typo. Make
the obvious fix to use the field from the external phy.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
Now that sys_check_timeouts() is called in net_lwip_rx(), there is no
need to call it from the SNTP receive loop. Remove the redundant call.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
|
|
The TFTP implementation does not resend the initial request if there is
no response from the server. Since TFTP is based on UDP, there should be
a mechanism to deal with unreliable transmissions at this point, similar
to what we have for data packets. Therefore, introduce request
retransmission.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
CC: Venkatesh Abbarapu <venkatesh.abbarapu@amd.com>
CC: Michal Simek <michal.simek@amd.com>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Introduce the DNS Kconfig symbol so that various network commands may
use host names without the dns command (CMD_DNS) being selected.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
CC: E Shattow <e@freeshell.de>
|
|
In rvu_af_init if the code fails to allocate memory for nix_af it will
take the error path with nix_af == NULL which will dereference nix_af.
Add the appropriate NULL check.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
In nix_lf_setup there is a default value assigned to err in case an
error is detected. However this default value will be overwritten in the
for loop so that later code does not return an error code from the
function. Add a new assignment to restore err to the default error code.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
In mvpp2_probe the code attempts to get a value for "gop-port-id" and
assigns it to port->gop_id but it then tests port->id for being equal to
-1. That is an impossible test as port->id is a field of type u8 so
cannot be negative. Change the test to port->gop_id.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
In phy_info_parse all uses of the variable phyaddr are as an int so
declaring as u32 is not useful and prevents the test for an error return
from fdtdec_get_int ever detecting an error. Change phyaddr to be an
int.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
Instead of returning -1 on a failed alloc, return -ENOMEM.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
You cannot test an unsigned char to be >= 256. Instead make the
variables start and end to be ints.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
In mv88e6xxx_port_enable when attempting to mask out the previous
settings of two bits a logical operator was used instead of a bitwise
operator. Fix this.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
In mtk_eth_of_to_plat, the last error check has the value in
'priv->phy_addr' but returns ret. Correct to return 'priv->phy_addr'
instead.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
In ldpaa_eth_open a memset is used to initialise a struct to 0 but the
size passed is that of a different struct. Correct to pass the sizeof
the struct that is being initialised.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
The header of LiMon imported files reference a License file which
does not exist in U-Boot. Some files were forgotten when adding the
SPDX-License-Identifier.
The LiMon files were originally licensed under GPLv2 as can be seen in
commit [2ea91039].
Based on this commit, add the correct SPDX license identifier.
While at it drop the reference to the non-existing License file from all
LiMon files and update the SPDX-License-Identifier to SPDX version 3.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
|
|
Add Kconfig symbol LWIP_ICMP_SHOW_UNREACH which, when enabled, prints a
message to the console upon reception of ICMP unreachable messages. For
example:
$ make qemu_arm64_lwip_defconfig
$ qemu-system-aarch64 -M virt -cpu max -nographic -bios u-boot.bin
[...]
=> dhcp
DHCP client bound to address 10.0.2.15 (0 ms)
=> tftp 192.168.0.100:69:Image
Using virtio-net#32 device
TFTP from server 192.168.0.100; our IP address is 10.0.2.15
Filename 'Image'.
Load address: 0x40200000
Loading: ICMP destination unreachable (host unreachable) from 192.168.0.16
Timeout!
=> tftp 192.168.0.16:69:Image
Using virtio-net#32 device
TFTP from server 192.168.0.16; our IP address is 10.0.2.15
Filename 'Image'.
Load address: 0x40200000
Loading: ICMP destination unreachable (port unreachable) from 192.168.0.16
Timeout!
=>
Submitted upstream as https://github.com/lwip-tcpip/lwip/pull/73.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
|
|
Allow reporting ICMP destination unreachable messages via a user-defined
callback.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
|
|
It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
get_timer returns a ulong value representing system time in ms.
On a 64-bit system, this ulong value is 64 bits long. However,
the driver stores it in a 32-bit unsigned integer, which overflows
after 49 days up time, causing the driver to get an incorrect time.
Replace the unsigned int variable with a ulong type to properly store
the value returned by get_timer.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
In comphy_cp110_init_serdes_map in comphy_cp110.c there are two fields
in cfg, comphy_lanes_count and comphy_mux_bitcount, which are fetched
from the FDT blob with fdtdec_get_int which returns an int. These two
fields are then tested for being negative. However the fields are
declared as unsigned so those tests must always fail. Change the
declaration of those fields to be int instead of u32 and the code will
work as expected.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
|
|
The limit checks in get_speed_string and get_type_string are off by 1 as
they do not account for the maximum index into an array that can be used
is 1 less than the number of elements in that array. Adjust the limit
checks to allow for this.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
|
|
In vsc8514_config there is a while loop for detecting a config failure
using a timeout counter with a post-decrement. In the case of a timeout
this will result in the loop exiting with timeout == -1 so use that as
the test below the loop to detect that the timeout occurred.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
|
|
In octeontx_smi_probe if an error is detected then memory that was
allocated is not freed. Small refactor of the code to use a common
return and free memory. Also return -ENOMEM for an allocation failure.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
In nicvf_cq_handler there is a test for !cqe_count which will return if
true so it is guaranteed that cqe_count will true after that point. This
makes the later test for cqe_count redundant so it can be removed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
In nicvf_rcv_pkt_handler there is no need to initialise err as it is
assigned to immediately after. Also the test for !pkt will return if
true meaning that pkt is guaranteed to be true after that code block and
so no need to test for it and the redundant test can be removed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
|
|
Fixes for newer revision of Retronix R-Car V4H Sparrow Hawk and fixes
for boards which enable POSITION_INDEPENDENT and also set non-zero
CONFIG_TEXT_BASE.
|
|
The Renesas board defconfigs explicitly set CONFIG_TEXT_BASE=0x50000000,
however U-Boot's POSITION_INDEPENDENT=y build default already places text
at 0x0. These hardcoded overrides are therefore unnecessary and will be
pruned automatically in upcoming resyncs.
Remove the CONFIG_TEXT_BASE lines from the following defconfigs:
- hihope_rzg2_defconfig
- r8a77970_eagle_defconfig
- r8a77970_v3msk_defconfig
- r8a77990_ebisu_defconfig
- r8a77995_draak_defconfig
- r8a779a0_falcon_defconfig
- renesas_rzg2l_smarc_defconfig
- rz2_beacon_defconfig
- silinux_ek874_defconfig
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
R-Car V4H Sparrow Hawk board
Retronix R-Car V4H Sparrow Hawk EVTA1 is populated with Spansion S25FS512S,
EVTB1 is populated with Winbond W77Q51NW. Describe the SPI NOR using generic
"jedec,spi-nor" compatible, because both flashes can be auto-detected based
on their built-in IDs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
V4H Sparrow Hawk EVTB1
The Retronix R-Car V4H Sparrow Hawk EVTB1 uses 1V8 IO voltage supply
for VDDQ18_25_AVB power rail. Update the AVB0 pinmux to reflect the
change in IO voltage. Since the VDDQ18_25_AVB power rail is shared,
all four AVB0, AVB1, AVB2, TSN0 PFC/GPIO POC[7..4] registers have to
be configured the same way.
Correct the voltage for EVTA1 boards accordingly by patching the U-Boot
control DT in SPL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
R-Car V4H Sparrow Hawk EVTB1
Invert the polarity of microSD voltage selector on Retronix R-Car V4H
Sparrow Hawk board. The voltage selector was not populated on prototype
EVTA1 boards, and is implemented slightly different on EVTB1 boards. As
the EVTA1 boards are from a limited run and generally not available,
update the DT to make it compatible with EVTB1 microSD voltage selector.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
board
Enable support for PCIe based xHCI USB 3.0 driver and USB mass
storage support on Retronix R-Car V4H Sparrow Hawk board .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Sparrow Hawk
The R-Car V4H SoC before rev.3.0 can not support dual-rank LPDDR5 DRAM.
This affects 16 GiB dual-rank DRAM configuration of Retronix R-Car V4H
Sparrow Hawk board. Fall back to 8 GiB single-rank DRAM configuration
on such systems instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Sparrow Hawk EVTA1
The Retronix R-Car V4H Sparrow Hawk old revision EVTA1 does not have MicroSD
voltage switch populated on the board, therefore the board supports only 3V3
and non-UHS MicroSD cards. While the EVTB1 board is populated with Winbond
W77Q51NW SPI NOR, the EVTA1 board is populated with Spansion S25FS512S SPI
NOR, those those SPI NOR IDs to discern the two board revisions and apply
the MicroSD related DT changes.
The MicroSD related DT changes modify the regulator node, which is now a
regulator-fixed and supplies only 3V3, and remove sd-uhs-sdr50 and
sd-uhs-sdr104 properties from the MicroSD slot controller node.
The MicroSD related DT changes cannot be applied as DTO, because the base
DT contains nodes which have to be removed in case of EVTA1, but have to
be present in case of EVTB1 and newer revisions of the board. Because the
EVTA1 is an old revision of the board that is not generally available, it
is better to special case it and keep the base DT compatible with EVTB1
and newer revisions of the board which are actually available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
R-Car V4H Reference Manual R19UH0186EJ0130 Rev.1.30 Apr. 21, 2025
page 4581 Figure 104.3b Initial Setting of PCIEC(example) middle
of the figure indicates that fourth write into register 0x148 [2:0]
is 0x3 or GENMASK(1, 0). The current code writes GENMASK(11, 0)
which is a typo. Fix the typo.
Fixes: be3dd0dc2fd9 ("pci: pcie-rcar-gen4: Add Renesas R-Car Gen4 DW PCIe controller driver")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The bootmeth rauc should scan all partitions, in particular whole
devices, and not be a global method. There may exist multiple RAUC
systems on different devices and they should all be detected. This also
fixes a bug, where both a global bootflow and one using an actual,
complete device would be detected at the same time, when scanning for
valid bootflows.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
|
|
As part of renaming environment related Kconfig options,
ENV_MMC_SW_PARTITION was inadvertently changed from a string to a bool.
Correct this.
Fixes: ffc4914703a2 ("env: Rename ENV_MMC_PARTITION to ENV_MMC_SW_PARTITION")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
CI: https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/27379
- Board: mbv: Prepare MBV for CI
- Board: MPFS Icicle Kit cleanup
- Board: Add Andes Voyager board support
- RISCV: Update SYS_BOOTM_LEN to commonly used value
- starfive: fix return code of `mac write_eeprom`
- arch/riscv/lib: update memmove and memcpy for big-endian
|
|
Change the shift patterns for the unaligned memory move and copy code
to deal with big-endian by definign macros to change the shfit left and
right to go the opposite way.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
