summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-06-13net: zynq_gem: Fix return type for phy...()Michal Simek
wait_for_bit_le32 returns negative value on failure. Fix phy...() to handle these failures properly. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: mvgbe: extract common code for SMI waitChris Packham
Combine repeated code from smi_reg_read/smi_reg_write into a common function smi_wait_ready. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: designware: set the PS bit when resetting DMA bus in MII configurationQuentin Schulz
On the SPEAr600 SoC, which has the dwmac1000 variant of the IP block, the DMA reset never succeeds when a MII PHY is used (no problem with a GMII PHY). The designware_eth_init() function sets the DMAMAC_SRST bit in the DMA_BUS_MODE register, and then polls until this bit clears. When a MII PHY is used, with the current driver, this bit never clears and the driver therefore doesn't work. The reason is that the PS bit of the GMAC_CONTROL register should be correctly configured for the DMA reset to work. When the PS bit is 0, it tells the MAC we have a GMII PHY, when the PS bit is 1, it tells the MAC we have a MII PHY. Doing a DMA reset clears all registers, so the PS bit is cleared as well. This makes the DMA reset work fine with a GMII PHY. However, with MII PHY, the PS bit should be set. We have identified this issue thanks to two SPEAr600 platform: - One equipped with a GMII PHY, with which the existing driver was working fine. - One equipped with a MII PHY, where the current driver fails because the DMA reset times out. Note: Taken from https://www.spinics.net/lists/netdev/msg432578.html Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: phy: mv88e61xx: Force CPU port link upChris Packham
When connecting to from a CPU direct to a 88e6097 typically RGMII is used. In order for traffic to actually pass we need to force the link up so the CPU MAC on the other end will see the link. Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13mvebu: neta: align DMA buffersJon Nettleton
This makes sure the DMA buffers are properly aligned for the hardware. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: add Socionext AVE ethernet driver supportKunihiko Hayashi
Add driver for Socionext AVE ethernet controller that includes MAC and MDIO bus supporting RGMII/RMII modes. The driver behaves the ethernet driver model (DM_ETH) with devicetree. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: include/phy.h: add new mode for internal phyKunihiko Hayashi
Add the new mode to indicate a built-in PHY. This will be used by UniPhier AVE ethernet driver. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13drivers/net/vsc9953: Initialize action RAM in VCAP complexRadu Bulie
VCAP tables must be initialized even if no advanced classification is used. If no initialization is performed, then ECC error will be observed by the user when the first packet enters the l2switch. The error is marked in MPIC_EISR0 -bit 29 which means - Internal RAM multi-bit ECC error. This patch fixes the aforementioned ECC error by performing the initialization of VCAP tables. Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: nfs: don't fail when nfs_read_reply returns -NFS_RPC_DROPVasily Khoruzhick
That can happen if duplicate UDP packet arrived, and that's not uncommon. Anyway, we ignore packets with rpc_id lower than last we sent for other requests, so it makes sense to do that for read request as well. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: cpsw: ti: Reap completed packets before stopping interfaceAlex Kiernan
If you send a final packet just before stopping the interface (e.g. a final ACK as part of the UDP fastboot protocol), then that packet isn't reliably delivered onto the wire. Reap packets prior to stopping the interface to ensure any which are in-flight make it out. Also remove buffer and len from the call to cpdma_process() as we weren't using them on their return. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: Protect net_state from reentrant net_loop()Leonid Iziumtsev
Global variable "net_state" is used in net_loop() state-machine. But it happens that some times the net_loop() can be called multiple times in the same call stack. For example when the netconsole is enabled and we print the message while some other net protocol is in action. Netconsole will overwrite the "net_state" and that will break the logic for earlier started protocol. To protect the state save and restore "net_state" variable each time when we enter and exit net_loop(). Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@se.atlascopco.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net/phy/cortina: Add support for CS4223 PHYVicentiu Galanopulo
Add support for Cortina CS4223 10G PHY - As per the CS4223 specs, an EEPROM module is connected to the PHY. At startup the PHY reads the firmware line and tries to load the firmware into the internal memory. - This driver reads the EEPROM status and checks if firmware has been loaded Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: sunxi: Correct MAC address register orderJoe Hershberger
Put the enetaddr data in the same order as it was before the change in commit ace1520cb5fc ("net: sunxi-emac: Write HW address via function") Reported-by: Udo Maslo <u.maslo@web.de> Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: Express LINK_LOCAL dependency on LIB_RANDJoe Hershberger
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13tsec: Fix reading phy registers from DTMario Six
Bus translations should be applied when reading the address of the sgmii phy registers from the DT. Use ofnode_get_addr_index instead of the plain ofnode_read_u32_default to fix this. Signed-off-by: Mario Six <mario.six@gdsys.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: Initialize as many ethernet devices as possibleMario Six
On devices that have their first network interface provided by a FPGA, the initialization of further interfaces will fail if the FPGA is not yet programmed. This leads to problems during factory setup when the data is supposed to be loaded over secondary netowork interfaces. To avoid this, use the uclass_{first,next}_device_check functions to initialize as many ethernet devices as possible. Signed-off-by: Mario Six <mario.six@gdsys.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: Always align tx packetsMario Six
Make sure that TX packets are always cache-aligned. Signed-off-by: Mario Six <mario.six@gdsys.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13ARM: DTS: resync a3517.dtsi with Linux 4.17Adam Ford
Linux 4.17 was just released with some minor changes to the am3517.dtsi. This patch re-syncs the file. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-13ARM: am3517_evm: Enable SPL_OF_CONTROL and SPL_OF_PLATDATAAdam Ford
The SPL doesn't have much room, so in order to support OF_CONTROL in SPL, we need the extra functionality of SPL_OF_PLATDATA. Adding these features allows us to remove a small part of code without losing the serial port during SPL. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-13dra76: fix HDMI HPD pinmuxTomi Valkeinen
The pin used for HDMI HPD should be set to GPIO mode on DRA76, similarly to all the other DRA7 and AM5 SoCs. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2018-06-13dra7/am5: remove CEC pin pull-upTomi Valkeinen
HDMI CEC pins are set to pull-up, but CEC requires no pull. Fix this. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2018-06-13env: Add !ENV_IS_IN_EXT4 dependency to ENV_IS_NOWHEREAlex Kiernan
If ENV_IS_IN_EXT4 is set you shouldn't be able to select ENV_IS_NOWHERE. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Petr Vorel <petr.vorel@gmail.com>
2018-06-13u-boot: Fix several typosShyam Saini
's/environemnt/environment/' and 's/Environemnt/Environment/' Signed-off-by: Shyam Saini <shyam@amarulasolutions.com>
2018-06-13tools: env: Use getline rather than fgets when reading config/scriptAlex Kiernan
When reading the config file, or a script file, use getline rather than fgets so line lengths aren't limited by the size of a compiled in buffer (128 characters for config, 1024 for scripts). Rename 'dump' to 'line' so it's clear we're working with a line of text. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-06-13AM3517_EVM: Fix Environmental locationAdam Ford
The am3517-evm boards stores the environment in NAND, but after merging various configs, the board was trying to load environment variables from FAT which would ultimately fail and cause some chatter. This patch removes the ENV_IS_IN_FAT flag to eliminate the noise. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-13lib: Add hexdumpAlexey Brodkin
Often during debugging session it's very interesting to see what data we were dealing with. For example what we write or read to/from memory or peripherals. This change introduces functions that allow to dump binary data with one simple function invocation like: ------------------->8---------------- print_hex_dump_bytes("", DUMP_PREFIX_OFFSET, buf, len); ------------------->8---------------- which gives us the following: ------------------->8---------------- 00000000: f2 b7 c9 88 62 61 75 64 72 61 74 65 3d 31 31 35 ....baudrate=115 00000010: 32 30 30 00 62 6f 6f 74 61 72 67 73 3d 63 6f 6e 200.bootargs=con 00000020: 73 6f 6c 65 3d 74 74 79 53 33 2c 31 31 35 32 30 sole=ttyS3,11520 00000030: 30 6e 38 00 62 6f 6f 74 64 65 6c 61 79 3d 33 00 0n8.bootdelay=3. 00000040: 62 6f 6f 74 66 69 6c 65 3d 75 49 6d 61 67 65 00 bootfile=uImage. 00000050: 66 64 74 63 6f 6e 74 72 6f 6c 61 64 64 72 3d 39 fdtcontroladdr=9 00000060: 66 66 62 31 62 61 30 00 6c 6f 61 64 61 64 64 72 ffb1ba0.loadaddr 00000070: 3d 30 78 38 32 30 30 30 30 30 30 00 73 74 64 65 =0x82000000.stde 00000080: 72 72 3d 73 65 72 69 61 6c 30 40 65 30 30 32 32 rr=serial0@e0022 00000090: 30 30 30 00 73 74 64 69 6e 3d 73 65 72 69 61 6c 000.stdin=serial 000000a0: 30 40 65 30 30 32 32 30 30 30 00 73 74 64 6f 75 0@e0022000.stdou 000000b0: 74 3d 73 65 72 69 61 6c 30 40 65 30 30 32 32 30 t=serial0@e00220 000000c0: 30 30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00.............. ... ------------------->8---------------- Source of hexdump.c was copied from Linux kernel v4.7-rc2. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Mario Six <mario.six@gdsys.cc> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Cc: Stefan Roese <sr@denx.de>
2018-06-13fs: btrfs: Fix not all CHUNK_ITEMs being read from CHUNK_TREEYevgeny Popovych
This causes errors when translating logical addresses to physical: btrfs_map_logical_to_physical: Cannot map logical address <addr> to physical btrfs_file_read: Error reading extent The behavior of btrfs_map_logical_to_physical() is to stop traversing CHUNK_TREE when it encounters first non-CHUNK_ITEM, which makes only some portion of CHUNK_ITEMs being read. Change it to skip over non-chunk items. Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com> Cc: Marek Behun <marek.behun@nic.cz> Cc: Sergey Struzh <sergeys@pointgrab.com> Reviewed-by: Marek Behun <marek.behun@nic.cz>
2018-06-13ARM64: meson: Sync DT with Linux 4.17Neil Armstrong
Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.17.0 This will enable USB on Amlogic Meson GXL Boards like Khadas VIM, P212 or LibreTech-CC. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-06-13fs: fat: fix wrong casting to unsigned value of sect_to_cluster()Seung-Woo Kim
After the commit 265edc03d5a1 ("fs/fat: Clean up open-coded sector <-> cluster conversions"), it is hung up writing new file to FAT16 disk with more than 19 files in armv7. It is because result value of sect_to_cluster() is not proper by casting from signed value to unsigned value. Fix the wrong casting of sect_to_cluster(). Reported-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-06-12include/linux/byteorder: Sync to latest Linux definitionsRamon Fried
generic.h has changed in Linux and new addtionals functions were added. This commit takes the latest and greatest from Linux (v4.17-rc5) to aid with porting drivers that utilize these functions. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-06-12doc: cmd: bubt: drop duplicated textBaruch Siach
This commit removes text that is exact duplicated of the text above. Cc: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de>
2018-06-12configs: pcm051: Use am335x-wega-rdk.dtb as fdtfileMatwey V. Kornilov
In upstream Linux kernel, the fdtfile for this specific board is called am335x-wega-rdk.dtb Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2018-06-12configs: pcm051: Use DEFAULT_LINUX_BOOT_ENV instead of hardcoded valuesMatwey V. Kornilov
It appears that DEFAULT_LINUX_BOOT_ENV can be used to boot pcm051 board. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2018-06-12configs: pcm051: Use DEFAULT_MMC_TI_ARGS instead of hardcoded duplicatesMatwey V. Kornilov
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2018-06-12configs: pcm051: Support distro bootcmdsMatwey V. Kornilov
Add support for distro bootcmds. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2018-06-12Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-06-12Merge git://git.denx.de/u-boot-marvellTom Rini
2018-06-12arm: mvebu: Add Helios4 Armada 38x initial supportDennis Gilmore
The helios4 is built on the SolidRun Armada 38x SOM. The port os based on the ClearFog board, using information from https://github.com/helios-4/u-boot-marvell as well as dtb input from https://github.com/helios-4/linux-marvell Signed-off-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: Dennis Gilmore <dgilmore@redhat.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-11LS1012AFRWY: Add Secure Boot supportVinitha V Pillai
Added the following: 1. defconfig for LS1012AFRWY Secure boot 2. PfE Validation support Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-11board: ls1012a: FRWY-LS1012A board supportBhaskar Upadhaya
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> [yorks: rebase and fix SPDX tag] [yorks: fix board/freescale/ls1012afrdm/Kconfig] Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board: Kconfig: Re-Arrangement of PPA firmware and header addressesBhaskar Upadhaya
PPA firmware and header address may vary depending upon different boards, configure ppa firmware and header address in board specific Kconfig. Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08arm: ls1021aqds: config: enable CONFIG_ID_EEPROM for mac commandJagdish Gediya
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board/freescale,lsch3: Add entry for 0.9vPriyanka Jain
As per updated hardware documentation for lsch3 based chips like LS2088A, 0.9v support has been added in possible supported SoC volatges Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08armv8: ls1088a: Enable USB in ls1088ardb_sdcard_qspi_SECURE_BOOT_defconfigRan Wang
Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08Merge branch 'master' of git://git.denx.de/u-boot-ubiTom Rini
2018-06-08Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2018-06-08Merge git://git.denx.de/u-boot-dmTom Rini
2018-06-07cmd: add missing line breaks for pr_err()Seung-Woo Kim
After the commit 9b643e312d52 ("treewide: replace with error() with pr_err()"), there are some pr_err() with no line break. Add missing line breaks. Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
2018-06-07board: samsung: add missing line breaks for pr_err()Seung-Woo Kim
After the commit 9b643e312d52 ("treewide: replace with error() with pr_err()"), there are some pr_err() with no line break. Add missing line breaks. Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2018-06-07script: Make get_default_envs.sh script exclude tools/envSeung-Woo Kim
If building envtools, there is env directory in tools directory. Mafe the get_default_envs.sh script exclude tools/env directory. Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
generated by cgit v1.2.3 (git 2.0.4) at 2025-11-02 19:35:04 +0000