| Age | Commit message (Collapse) | Author |
|---|
|
won't print anything
Return from ddr3_tip_print_log() early if we won't print anything
anyway.
This way the compiler can optimize away the VALIDATE_IF_ACTIVE() calls
in the for-loop, so if the SILENT_LIB macro is defined, no code is
generated for the rest of the function, which saves some space.
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
Turris Omnia defconfig is nearing image size limit. Disable ext4 write
support to reserve space for more important stuff.
This reduces the size of the KWB image by ~19 KiB.
If in the future U-Boot supports compressing itself and decompressing
on load, we may enable this again.
Signed-off-by: Marek Behún <kabel@kernel.org>
|
|
- Change the spi-max-frequency to 50000000 (50 Mhz). According to the
data sheet[1], the MX25L3205D max frequency is 86 Mhz. Using 50 Mhz in
the DTS to ensure u-boot is consistent with what Linux kernel expected.
- Update GPIO fan to conform to the latest DT binding.
[1]
https://www.macronix.com/Lists/Datasheet/Attachments/8575/MX25L3205D,%203V,%2032Mb,%20v1.5.pdf
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
|
|
The CONFIG_ENV_OFFSET is undefined if boot device is UART
(CONFIG_MVEBU_SPL_BOOT_DEVICE_UART), or envs are not stored on flash
(CONFIG_ENV_IS_NOWHERE). Check for CONFIG_ENV_IS_IN_SPI_FLASH as the first
condition to determine whether env_sf_get_env_addr() should be provided.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
|
|
Add support for a Marvell Armada 3720 device variant
Signed-off-by: Benjamin Schneider <ben@bens.haus>
|
|
Upstream Linux commit f90b68d6c8b0.
The CORE/BUS root slice has following design, simplied graph:
The difference is core not have pre_div block.
A composite core/bus clk has 8 inputs for mux to select, saying clk[0-7].
It support target(smart) interface and normal interface. Target interface
is exported for programmer easy to configure ccm root. Normal interface
is also exported, but we not use it in our driver, because it will
introduce more complexity compared with target interface.
The normal interface simplified as below:
SEL_A GA
+--+ +-+
| +->+ +------+
CLK[0-7]--->+ | +-+ |
| | | +----v---+ +----+
| +--+ |pre_diva+----> | +---------+
| +--------+ |mux +--+post_div |
| +--+ |pre_divb+--->+ | +---------+
| | | +----^---+ +----+
+--->+ | +-+ |
| +->+ +------+
+--+ +-+
SEL_B GB
The mux in the upper pic is not the target interface MUX, target
interface MUX is hiding SEL_A and SEL_B. When you choose clk[0-7],
you are actually writing SEL_A or SEL_B depends on the internal
counter which will also control the internal "mux".
The target interface simplified as below which is used by Linux Kernel:
CLK[0-7]--->MUX-->Gate-->pre_div-->post_div
A requirement of the Target Interface's software is that the
target clock source is active, it means when setting SEL_A, the
current input clk to SEL_A must be active, same to SEL_B.
We touch target interface, but hardware logic actually also need
configure normal interface.
There will be system hang, when doing the following steps:
The initial state:
SEL_A/SEL_B are both sourcing from clk0, the internal counter
choose SEL_A.
1. switch mux from clk0 to clk1
The hardware logic will choose SEL_B and configure SEL_B to clk1.
SEL_A no changed.
2. gate off clk0
Disable clk0, then the input to SEL_A is off.
3. switch from clk1 to clk2
The hardware logic will choose SEL_A and configure SEL_A to clk2,
however the current SEL_A input clk0 is off, the system hang.
The solution to fix the issue is in step 1, write twice to
target interface MUX, it will make SEL_A/SEL_B both sources
from clk1, then no need to care about the state of clk0. And
finally system performs well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
Make public the clk_fetch_parent_index and rename it. This allow
us to be reused in driver specialization
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
Add missing newline character and also add the return code of
regulator_set_value() to the output.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
|
|
Initialize the Cryptographic Accelerator and Assurance Module.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
|
|
Since commit ecb1c37a7b64 ("clk: imx8mp: Add EQoS MAC clock"),
the clocks for the DWMAC driver can be configured, and removing
them breaks operation.
Fixes: ecb1c37a7b64 ("clk: imx8mp: Add EQoS MAC clock")
Suggested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Booting an initramfs with the current initrd_addr address may lead to
initramfs corruption and boot failure.
Fix the initramfs problem by applying the following layout
suggested by Tom Rini:
loadaddr=0x40480000 --> Gets moved to 0x40600000 in run-time:
Uncompressing Kernel Image
Moving Image from 0x40480000 to 0x40600000, end=41e80000
fdt_addr_r= moved loadaddr + 128 MiB = 0x48600000
initrd_addr=fdt_addr_r + 512 KiB = 0x48680000
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Synchronize R-Car R8A779G0 V4H PFC tables with Linux 6.9.3,
commit 1b4861e32e461b6fae14dc49ed0f1c7f20af5146 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Synchronize R-Car R8A779H0 V4M clock tables with Linux 6.9.3,
commit 1b4861e32e461b6fae14dc49ed0f1c7f20af5146 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Synchronize R-Car R8A779G0 V4H clock tables with Linux 6.9.3,
commit 1b4861e32e461b6fae14dc49ed0f1c7f20af5146 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Synchronize R-Car R8A779F0 S4 clock tables with Linux 6.9.3,
commit 1b4861e32e461b6fae14dc49ed0f1c7f20af5146 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Synchronize R-Car R8A779A0 V3U clock tables with Linux 6.9.3,
commit 1b4861e32e461b6fae14dc49ed0f1c7f20af5146 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Synchronize R-Car R8A77951 H3 clock tables with Linux 6.9.3,
commit 1b4861e32e461b6fae14dc49ed0f1c7f20af5146 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Before this commit, usb_get_descriptor() failed for some flakey USB
devices. We hereby adopt the more robust linux implementation [1].
For instance, for the "Alcor Micro Corp. Flash Drive" (VID 0x058f, PID
0x6387), the following behavior occurs from time to time:
=> usb start
starting USB...
Bus xhci_pci: Register 10000840 NbrPorts 16
Starting the controller
USB XHCI 1.20
scanning bus xhci_pci for devices... usb_new_device: Cannot read configuration, skipping device 058f:6387
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
[1] From a38297e3fb012 (Linux 6.9), see
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/drivers/usb/core/message.c?h=v6.9#n781
|
|
Replace one type of terrible code formatting with a different
type of terrible code formatting. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hector Martin <marcan@marcan.st>
|
|
The mux flags (u8), div flags (u8), and gate flags (u8) are not the clk
flags (unsigned long). They have different meanings
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
The mux flags (u8), div flags (u8), and gate flags (u8) are not the clk
flags (unsigned long). They have different meanings
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
rev.200
The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses
for the Fast ethernet PHYs. Update the base SoM DT and SoM rev.100 backward
compatibility DTO to cater for this change.
Since the MDIO address adjustment is now also in the rev.100 SoM DTO, not
only in the rev.100 PDK3 DTO, update Makefile accordingly as well, else the
DTC would complain about the DTO overriding the 'reg' property without also
updating the node unit-address, which is not doable without duplicating the
entire PHY node in the DTO, which leads to large amount of duplication with
no gain.
Fixes: 9de599ec3d59 ("arm64: dts: imx8mp: Update i.MX8MP DHCOM SoM DT to production rev.200")
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Enable PCA953x GPIO expander driver in DH i.MX8MP DHCOM PDK2 configuration.
The PCA9539 GPIO expander is used on production DH i.MX8MP DHCOM SoM rev.200.
This is already enabled in DH i.MX8MP DHCOM PDK3 configuration so align the
two configurations.
Fixes: 9de599ec3d59 ("arm64: dts: imx8mp: Update i.MX8MP DHCOM SoM DT to production rev.200")
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Enable 'cat' command to print file from filesystem to stdout.
Enable 'xxd' command to hexdump file from filesystem to stdout.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
The older i.MX8M Mini Verdin SoMs may came with 20 MHz SPI CAN controller
oscillator, the newer SoMs always use 40 MHz oscillator. Handle both by
overriding the oscillator frequency just before booting the kernel.
These are the known variants with 20 MHz oscillator:
- 0055, V1.1A, V1.1B, V1.1C and V1.1D, use a 20MHz oscillator
- 0059, V1.1A and V1.1B, use a 20MHz oscillator
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
- Re-instate the zlib update, so we can fix it for this release,
assorted whitespace cleanups, allow mkimage to 'auto-conf' signing of
scripts, enhance ELF image support, add more HW rev support to e1000
driver, update am64x_evm config, correct mpc8xxx watchdog, update
phycore-am6 docs.
|
|
Now that the release has happened, bring back the update to zlib.
This reverts commit bbacdd3ef7762fbdeab43ceea5205d1fd0f25bbd.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Timer value is a 16 bits calculated from the wanted timeout and the
system clock. On powerpc/8xx, a timeout of 2s gives a value which
is over U16_MAX so U16_MAX shall be used. But the calculation is
casted to u16 so at the end the result is 63770 instead of 128906.
So the timer gets loaded with 63770 instead of 65535. It is not
a big difference in that case, but lets make the code correct and
cast to u32 instead of u16.
Fixes: 26e8ebcd7cb7 ("watchdog: mpc8xxx: Make it generic")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
This patch fixes the I225 hardware default value
at 0x15FD meaning empty flash image
or the NVM configuration loading failed
Signed-off-by: Marjolaine Amate <marjolaine.amate@odyssee-systemes.fr>
|
|
This patch adds support for Intel Foxville I226
devices LM,V,I,K in e1000 driver.
Signed-off-by: Marjolaine Amate <marjolaine.amate@odyssee-systemes.fr>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
|
|
The board has the TCA9554 I2C GPIO expander chip for expansion
board presence detection logic.
Enable the relevant I2C GPIO drivers.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
|
|
Some operating systems (e.g. seL4) and embedded applications are ELF
images. It is convenient to use FIT-images to implement trusted boot.
Added "elf" image type for booting using bootm command.
Signed-off-by: Maxim Moskalets <maximmosk4@gmail.com>
|
|
U-Boot configured for verified boot with the "required" option set to
"conf" also checks scripts put in FIT images for a valid signature, and
refuses to source and run such a script if the signature for the
configuration is bad or missing. Such a script could not be packaged
before, because mkimage failed like this:
% tools/mkimage -T script -C none -d tmp/my.scr -f auto-conf -k tmp -g dev -o sha256,rsa4096 my.uimg
Failed to find any images for configuration 'conf-1/signature'
tools/mkimage Can't add hashes to FIT blob: -1
Error: Bad parameters for FIT image type
This is especially unfortunate if LEGACY_IMAGE_FORMAT is disabled as
recommended.
Listing the script configuration in a "sign-images" subnode instead,
would have added even more complexity to the already complex auto fit
generation code.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
|
|
Describe how to boot via UART.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Drop all duplicate newlines from config headers.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-snapdragon
Various minor fixes and improvements:
* Fix Qualcomm SPMI v5 support
* Move default environment to a file
* Add support for special pins (e.g ufs/mmc reset/data pins)
* IPQ moves to OF_UPSTREAM and receives some cleanup and MAINTAINERS
changes
* Add a reset driver for devices without PSCI
* msm8916 USB clock improvements for mobile devices
|
|
Branch contains minor improvemets for existing tegra devices along
with bring up of 4 new devices (ASUS Transformers T20, Microsoft
Surface RT, Lenovo Ideapad Yoga 11 and WEXLER Tab 7t).
|
|
This change was brought in by accident, revert.
This reverts commit 51aabf50e57f5139de31a4850347edbad8bb338b.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The dm_usb_gadget_handle_interrupts() is not implemented by any USB
gadget controller drivers which do enable DM_USB_GADGET anymore. Set
the symbol as non-weak.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-12-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Drop dm_usb_gadget_handle_interrupts() in favor of empty default
implementation of the same in drivers/usb/gadget/udc/udc-uclass.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-11-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-10-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-9-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-8-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-6-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-4-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Implement .handle_interrupts callback as a replacement for deprecated
dm_usb_gadget_handle_interrupts() function. The new callback allows
for each DM capable USB gadget controller driver to define its own
IRQ handling implementation without colliding with other controller
drivers.
Keep the dm_usb_gadget_handle_interrupts() in this driver for non-DM
case for now, until this driver gets fully converted to DM USB gadget.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-3-marek.vasut+renesas@mailbox.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Introduce .ops for USB_GADGET_GENERIC uclass. The first new ops is
.handle_interrupts which must be implemented by DM capable USB gadget
controller drivers and must implement interrupt handling similar to
dm_usb_gadget_handle_interrupts(). This patch currently provides weak
dm_usb_gadget_handle_interrupts() implementation which is overridden by
the drivers, but this will be removed once conversion to handle_interrupts
callback is complete.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Link: https://lore.kernel.org/r/20240614005309.34433-2-marek.vasut+renesas@mailbox.org
[mkorpershoek: fixed trivial typo in commit message]
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
