| Age | Commit message (Collapse) | Author |
|---|
|
Remove not needed variables from environment.
- boot_scripts is not needed, the default value is just fine and
already includes boot.scr
- setup variable used to be executed from some bootscript, however
it's not required and there is no point on having this small helper
here
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
Add files produced by compilation of TI platforms:
*.ti-secure(-rom)
*.map
*-board-config
custMpk.pem
*.bin_*
*.fit
*.itb
tispl.bin_unsigned
Signed-off-by: Andrea Calabrese <andrea.calabrese@amarulasolutions.com>
|
|
In Linux, we allow sleep moci to be turned off when the carrier board
supports it and the system is in suspend. In U-Boot, however, we want
the sleep moci to be always on. So we use a gpio hog and disable the
regulator. This change is necessary because we switched to upstream
device tree files with commit c07bba7a2c7e ("verdin-am62: move verdin
am62 to OF_UPSTREAM"). A recent upstream patch removes the gpio hog from
the Linux device tree, so we need to add it to the u-boot dtsi. The
following patch will remove the gpio hog from the Linux device tree:
https://lore.kernel.org/linux-devicetree/20240301084901.16656-1-eichest@gmail.com/
The U-Boot patch can be applied without it and will not break the build.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
|
|
At present only MCU domain ESM is probed, this means errors
occurred in mcu domain will be propagate to MCU_SAFETY_ERRORn.
MCU ESM accepts SOC_SAFETY_ERRORn signal as Error
event and propagate to MCU_SAFETY_ERRORn.[0]
Therefore adding support to probe both main domain and mcu
domain ESM.
[0]: https://www.ti.com/lit/zip/spruil1
spruil1c.pdf from zip
Figure 12-1244. ESM Modules Overview
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
|
|
Enable MMC UHS support for to allow to enter the UHS
modes for MMC1.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
|
|
Avoid adding the same flag to KBUILD_CFLAGS twice.
Fixes: 8602d97ca2cf ("Makefile: avoid false positive -Wmaybe-uninitialized")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
Adds tifsstub binaries, this is required for deepsleep functionality.
This implements the same change as commit 128f81290b7d ("arm: dts: k3:
binman: am625: add support for signing TIFSSTUB Images") did for TI AM62
SK board.
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/20563
- Fix missing fdt_fixup on colibri-imx(6ull|imx7).
- Enable PCIe and NVMe on DH i.MX8M Plus DHCOM PDK3.
- Convert i.MX8M flash.bin image generation to binman
- Convert imx93-11x11-evk to OF_UPSTREAM.
|
|
|
|
Linux kernel driver drivers/mfd/tps6594-i2c.c is using different
name for compatible for tps6594 family PMIC.
After sync of Linux kernel DT to u-boot for TI platforms
J7200, J721S2 and J784S4 PMIC is no longer getting probed.
So updating compatible field to align with Linux driver and DT.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Reuse TPS65941 regulator driver to adds support for
TPS65224 PMIC's regulators. 4 BUCKs and 3 LDOs, where
BUCK1 and BUCK2 can be configured in dual phase mode.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Use function callbacks for volt2val, val2volt and slewrate lookups.
This makes it easier to add support for TPS65224 PMIC regulators.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Adds macros for buck and ldo ids and switched to using switch
case instead of if else in probe functions. Helps in adding
support for TPS65224 PMIC.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Adds compatible and data field values of TPS65224 driver in
TPS65941 PMIC driver.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Re-use the TPS65941 PMIC driver for TPS65224 PMIC.
Add additional macros of TPS65224 to aid in the driver
re-use.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Rework the flash.bin image generation such that it uses the new binman
nxp_imx8mimage etype. This way, the flash.bin is assembled in correct
order using plain binman, without any workarounds or sections assembled
in special DT node order.
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> # imx8mm_venice
Tested-by: Fabio Estevam <festevam@gmail.com> # imx8mm-evk and imx8mn-evk
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Include imx8mq-u-boot.dtsi in the board -u-boot.dtsi to pull in binman
configuration instead of duplicating it in the board -u-boot.dtsi again.
Drop the duplicate binman configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Add new binman etype derived from mkimage etype which generates configuration
input file for mkimage -T imx8mimage, and runs the mkimage on input data. The
mkimage -T imx8mimage is used to generate combined image with SPL and DDR PHY
blobs which is bootable on i.MX8M.
The configuration file generated here is equivalent of imx8mimage.cfg, which
is the file passed to '$ mkimage -T imx8mimage -n imx8mimage.cfg ...' . The
settings generated into the imx8mimage.cfg file are configured via supported
binman DT properties, nxp,boot-from, nxp,loader-address, nxp,rom-version.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Convert to OF_UPSTREAM for i.MX93 11x11 EVK.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Sync clock header with kernel 6.8
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Enable PCIe/NVMe support on DH i.MX8M Plus DHCOM PDK3. Except for
the configuration options which are enabled, add slight adjustment
to board u-boot.dtsi, which is necessary as there is currently no
driver for the I2C PCIe clock generator. Since the generator is
strapped to be always on, it is possible to supplant the generator
functionality by fixed-clock.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
In commit 51aaaf5e7975 ("board: toradex: imx: Remove not needed env variables")
the empty definition of fdt_fixup variable was removed, however this was
still referenced from the boot command leading to boot failures:
## Error: \"fdt_fixup\" not defined`
Fix this by removing "run fdt_fixup" from the boot command and instead
enable CONFIG_OF_ENV_SETUP in the defconfig that would achieve the same
but in a more robust way (it works fine even if the variable is not
defined).
Fixes: 51aaaf5e7975 ("board: toradex: imx: Remove not needed env variables")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip
Please pull the updates for rockchip platform:
- dts sync for rk3308;
- sdram: Support getting banks from TPL for rk3568 and rk3588;
- dts and config clean and sync up for rk3568/rk3588;
- Other misc fixes;
CI: https://source.denx.de/u-boot/custodians/u-boot-rockchip/-/pipelines/20543
|
|
https://source.denx.de/u-boot/custodians/u-boot-tpm
Minor changes on this PR.
Igor added some orphaned OP-TEE related files on the proper section
of MAINTAINERS and fixed a potential buffer overflow in tee-sandbox
|
|
RK356x-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the turing-rk1-rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the toybrick_rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the evb_rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
All defconfigs using the CONFIG_TARGET_EVB_RK3588 are updated at once
since they are impacted by this change.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the rock5b-rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the rock5a-rk3588s.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the quartzpro64-rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the nanopc-t6-rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
When Rockchip TPL blob is used, the memory areas that can be used for
DRAM is gotten from ATAGS passed through the DRAM at a specific address.
The DDR_MEM tag contains at most 10 areas, so we should default to 10 if
Rockchip TPL blob is used. Note that it is technically possible we need
more if one of those 10 areas overlaps with reserved memory area,
forcing us to split it in two. But a default doesn't need to handle all
cases, only most.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Allow RK3568 and RK3588 based boards to get the RAM bank configuration
from the ROCKCHIP_TPL stage instead of the current logic. This fixes
both an issue where 256MB of RAM is blocked for devices with >= 4GB
of RAM and where memory holes need to be defined for devices with
more than 16GB of RAM. In the event that neither SoC is used or the
ROCKCHIP_TPL stage is not used, fall back to existing logic.
The logic handles creating memory holes from reserved memory areas
defined in mem_map data struct in SoC C files, but only if the DRAM area
overlaps with one reserved memory area.
Since mem_map data struct is used, it should be rather straightforward
to add support for other SoCs if needed.
The logic is taken from Rockchip's U-Boot tag linux-5.10-gen-rkr4.1
(e08e32143dd).
Note that Rockchip's U-Boot/TF-A/OP-TEE modify the ATAGS at runtime as
well, but the DDR_MEM tag seems to be pretty much stable (though BL31
seems to be reserving only 1MB for itself at the moment).
u32 for ATAGS is used because it simplifies the pointer arithmetic and
it's expected that ATAGS are always below the 4GB limit allowed by u32.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Some variants of the ROCK Pi 4 series have an SPI flash chip populated
which can be booted from. This patch enables support in U-Boot for
building the image for the SPI flash, support for booting U-Boot from the
SPI flash chip and support in U-Boot for accessing the SPI flash using
`sf` commands.
Not all variants (e.g. ROCK Pi 4B, ROCK 4 Model C Plus, ROCK 4SE) come
populated with an SPI flash chip, but have the footprint on the board so
a user could solder their own to the board. With this patchset applied,
these board variants without an SPI flash chip still boot from MMC.
I have enabled support for both Winbond and XTX SPI flash devices since
different hardware variants have different devices populated:
- `rockpi4_v13_sch_20181112.pdf` contains a Winbond part `W25Q64FWZPIG`
- `rockpi4_v14_sch_20210114.pdf` contains an XTX part `XT25F32BWOIGT`
The ROCK Pi 4 I have is marked as "ROCK PI 4 v1.48" and contains an SPI
flash chip from XTX:
=> sf probe
SF: Detected xt25f32 with page size 256 Bytes, erase size 4 KiB, total 4 MiB
In the interest of supporting all board variants and not regressing
existing users who boot from MMC, I have enabled support for booting from
both SPI flash chip variants in the defconfig and left the environment
storage location as MMC to not break existing users who have the
environment stored on MMC.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
|
|
To prepare for ROCK Pi 4A SPI flash support, sync the DTS from Linux which
includes an SPI flash node.
Kernel tag: v6.6-rc1
Kernel commits:
- eddf73029770 ("arm64: dts: rockchip: Enable internal SPI flash for ROCK \
Pi 4A/B/C")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
|
|
The vop node should not be included in TPL/SPL control FDT, it should
only be included at U-Boot proper pre-reloc phase.
Change to use bootph-some-ram prop to fix this.
Fixes: 6794063d5065 ("ARM: dts: rk3328: Enable VOP for bootph-all")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Port the RK3328 part of the Rockchip IO-domain driver from linux.
This differs from linux version in that pmu io iodomain bit is enabled
in the write ops instead of in an init ops as in linux, this way we can
avoid keeping a full state of all supply that have been configured.
Enable by default on all RK3328 boards, skip rk3328-evb because this
target is typically also used on miscellaneous boards and boxes not
fully supported by U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The RK3328 SoC support ARMv8 Cryptography Extensions and use of the
ARMv8 crypto extensions help speed up FIT checksum validation in SPL.
Imply ARMV8_SET_SMPEN and ARMV8_CRYPTO to take advantage of the crypto
extensions for SHA256 when validating checksum of FIT images.
Also imply OF_LIVE to help speed up init of U-Boot proper.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Sort imply statements under ROCKCHIP_RK3328 alphabetically and remove
ENABLE_ARM_SOC_BOOT0_HOOK, DEBUG_UART_BOARD_INIT and SYS_NS16550, they
are already implyed or selected by ARCH_ROCKCHIP.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Use a wildcard to simplify the list of board DT files in the MAINTAINERS
file for the Radxa Rock 2 Square board.
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Display TPL init information message only when TPL_BANNER_PRINT
configuration entry is set. This allows to disable information
message in case logs on UART are unwanted.
Update parent ifdef condition to check also CONFIG_TPL_SERIAL
to match logic of the non-PX30 TPL implementation.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The commit 2cc6cde647e2 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") introduced a limit of number of blocks to
read to fix a Data End Bit Error on RK3568 and RK3588. This had a side
affect of significant slowing down reading FIT from eMMC.
After the commit 6de9d7b2f13c ("rockchip: rk35xx: Enable eMMC HS200 mode
by default") the limit of number of blocks to read workaround is no
longer necessary and at HS200+ a Data End Bit Error is no longer
happening using PIO mode.
Change this limitation to allow reading more than 4 blocks with a single
CMD18 command in PIO mode at HS200+ speed, keep using the 4 blocks
limitation when loadig FIT from eMMC at lower speed than HS200.
Fixes: 2cc6cde647e2 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The generic RK35xx board targets are intended to be used as a bare
minimum target that can be used to e.g. boot boards that mostly follow
reference hw design before a board spefic target has been added or for
flashing and recovery purposes.
Disable BOOTMETH_VBE, NET and ADC as these features are not intended to
ever be used by these minimal generic board targets.
Enable SYSRESET_PSCI to let TF-A handle sysreset from U-Boot proper.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add support for USB OTG, RockUSB and UMS to the generic RK3588S/RK3588
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The default pinctrl for UART2 is using M1 iomux, however, all other
supported RK3588 boards in U-Boot use M0 iomux for UART2.
Change to use the M0 pinctrl for UART2 to match other supported boards.
Fixes: b54c3d0dd69b ("rockchip: board: Add minimal generic RK3588S/RK3588 board")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add support for USB OTG, RockUSB and UMS to the generic RK3566/RK3568
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add support for booting from SPI flash using the generic RK3566/RK3568
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
