| Age | Commit message (Collapse) | Author |
|---|
|
Update maintainer for MediaTek MIPS platform
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
The BootROM of MT7621 requires a image header for SPL to record its size
and load address when booting from NAND.
To create such an image, one can use the following command line:
mkimage -T mtk_image -a 0x80200000 -e 0x80200000 -n "mt7621=1"
-d u-boot-spl-ddr.bin u-boot-spl-ddr.img
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
Add support to load legacy image with payload compressed. This redirects
the boot flow for all legacy images. If the payload is not compressed, the
actual behavior will remain unchanged.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
If the payload is compressed, SPL_COPY_PAYLOAD_ONLY should always be set
since the payload will not be directly read to its load address. The
payload will first be read to a temporary buffer, and then be decompressed
to its load address, without image header.
If the payload is not compressed, and SPL_COPY_PAYLOAD_ONLY is set, image
header should be skipped on loading. Otherwise image header should also be
read to its load address.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch removes the dependency to SPL_NAND_DRIVERS for SPL_NAND_BASE to
allow minimal spl nand driver to use nand base for probing NAND chips.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds NAND flash controller driver for MediaTek MT7621 SoC.
The NAND flash controller of MT7621 supports only SLC NAND flashes.
It supports 4~12 bits correction with maximum 4KB page size.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds GMAC support for MediaTek MT7621 SoC.
MT7621 has the same GMAC/Switch configuration as MT7623.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
The address returned by regmap_get_range() is not remapped. Directly r/w
to this address is ok for ARM platforms since it's idential to the virtual
address.
But for MIPS platform only virtual address should be used for access.
To solve this issue, the regmap api regmap_read/regmap_write should be used
since they will remap address before accessing.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
The iobase address from dts node is actually physical address. It's
identical to the virtual address in ARM platform. This is ok because this
driver was used only by ARM platforms (mt7622/mt7623 ...).
But now this driver will be used by mt7621 which is a MIPS SoC. For MIPS
platform the physical address space is mapped to KSEG0 and KSEG1 and this
makes the virtual address apparently not idential to its physical address.
To solve this issue, this patch replaces dev_read_addr with dev_remap_addr
to get the remapped iobase address.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds SDXC support for MediaTek MT7621 SoC
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch makes mt7621_wdt driver available for MediaTek MT7621 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch makes mt7621_gpio driver available for MediaTek MT7621 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch makes mt7621_spi driver available for MediaTek MT7621 SoC
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch makes mtk-tphy driver available for MediaTek MT7621 SoC
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch makes xhci-mtk driver available for MediaTek MT7621 SoC
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds pinctrl support for MediaTek MT7621 SoC.
The MT7621 SoC supports pinconf, but it is not the same as mt7628.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds reset controller bits definition header file for MediaTek
MT7621 SoC
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds a clock driver for MediaTek MT7621 SoC.
This driver provides clock gate control as well as getting clock frequency
for CPU/SYS/XTAL and some peripherals.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
The MT7621 requires external binary blob being executed during u-boot's
boot-up flow. It's necessary to provide a guide here for users to correctly
build the u-boot.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
The mt7621_rfb board supports integrated giga PHYs plus one external
giga PHYs. It also has up to 512MiB DDR3, 16MB SPI-NOR, 3 mini PCI-e x1
slots, SDXC and USB.
The mt7621_nand_rfb board is almost the same as mt7621_rfb board, but it
uses NAND flash and SDXC is not available.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds support for MediaTek MT7621 SoC.
All files are dedicated for u-boot.
The default build target is u-boot-mt7621.bin.
The specification of this chip:
https://www.mediatek.com/products/homenetworking/mt7621
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds support for noncached_alloc() which was only supported by
ARM platform.
Unlike the ARM platform, MMU is not used in u-boot for MIPS. Instead, KSEG
is provided to access uncached memory. So most code of this patch is copied
from cache.c of ARM platform, with only two differences:
1. MMU is untouched in noncached_set_region()
2. Address returned by noncached_alloc() is converted using KSEG1ADDR()
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch adds __image_copy_len needed by TPL of MT7621 SoC.
The __image_copy_len represents the binary blob size of both SPL/TPL
binaries. To achieve this, __text_start/end are added for calculation.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch add more definitions needed for MT7621 initialization.
MT7621 needs to initialize GIC/CPC and other related parts.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
To be compatible with old u-boot used by lots of MT7621 devices, the u-boot
needs to boot-up MT7621's all cores, and all VPES of each core.
This patch adds asm/mipsmtregs.h from linux kernel which is need for
boot-up VPEs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
- Alignment with Linux kernel device tree v5.19 for stm32mp15 and stm32mp13
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
|
|
PA13 and PA14 are used for USB power control and can't be used
to enforce fastboot or stm32prog mode by pressing a button.
Defining CONFIG_FASTBOOT/CONFIG_CMD_STM32PROG without this patch applied
results in fastboot/stm32prog always starting, because PA13/PA14 are always
low during boot. So drop the wrong trigger gpios definitions.
Signed-off-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Activate useful commands in STM32MP13x config, already activated in
stm32mp15_defconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Activate the I2C driver in STM32MP13x config.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Activate the RTC driver in STM32MP13x config.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Activate the RNG driver provided by OP-TEE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
On STM32MP13x STMicroelectronics boards, the UART can reliably go up to
4000000 bauds when connected to the external ST-LINKV3.
This patch adds the support of higher baudrates on STMicroelectronics
STM32MP13x boards with ST-LINKV3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Activate the led managed in stm32mp1 board for U-Boot indication
in STM32MP13F-DK device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Device tree alignment with Linux kernel v5.19-rc1 with:
- ARM: dts: stm32: add UserPA13 button on stm32mp135f-dk
- ARM: dts: stm32: add blue led (Linux heartbeat) on stm32mp135f-dk
- ARM: dts: stm32: add EXTI interrupt-parent to pinctrl node on stm32mp131
- ARM: dts: stm32: enable RTC support on stm32mp135f-dk
- ARM: dts: stm32: add RTC node on stm32mp131
- ARM: dts: stm32: fix pinctrl node name warnings (MPU soc)
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add support of STM32MP13x Rev.Y for the Silicon revision REV_ID = 0x1003.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
New IP adds a conditional reset that impact the clock
error management. It is now linked to a new compatible.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The stm32mp13 soc differs from the stm32mp15 in terms of
clear register offset for controlling the FMP (Fast Mode Plus).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add a "secure" version of STM32 boards based on SCMI when RCC_TZCR.TZEN=1.
Only boards provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
The resources secured by RCC_TZCR.TZEN=1 are managed by OP-TEE
and the associated SCMI services, reset and clock.
These device trees are only supported with stm32mp15_defconfig,
with OP-TEE, SCMI and without SPL support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
With support of SCMI in OP-TEE, the early malloc usage
increase, the associated defined CONFIG_SYS_MALLOC_F_LEN
need to be increased.
For example, for stm32mp15_defconfig and
stm32mp157c-dk2-scmi.dtsi, we have:
Early malloc usage: 14098 / 80000
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add support for new compatible st,stm32mp1-rcc-secure used when the
RCC resource is managed by secured world (RCC_TZCR.TZEN=1)
iand when SCMI is used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Device tree alignment with Linux kernel v5.19-rc1
- ARM: dts: stm32: Add alternate pinmux for ethernet0 pins
- ARM: dts: stm32: Add alternate pinmux for mco2 pins
- ARM: dts: stm32: fix pinctrl node name warnings (MPU soc)
- ARM: dts: stm32: stm32mp15-pinctrl: add spi1-1 pinmux group
- dt-bindings: clock: add IDs for SCMI clocks on stm32mp15
- dt-bindings: reset: add IDs for SCMI reset domains on stm32mp15
- dt-bindings: clock: stm32mp15: rename CK_SCMI define
- dt-bindings: reset: stm32mp15: rename RST_SCMI define
- dt-bindings: reset: add MCU HOLD BOOT ID for SCMI reset domains
on stm32mp15
- dt-bindings: clk: cleanup comments
- ARM: dts: align SPI NOR node name with dtschema
- ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15
- ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
- ARM: dts: stm32: move SCMI related nodes in a dedicated file for
stm32mp15
+ patch from stm32-dt-for-v5.19-fixes-2
- ARM: dts: stm32: move SCMI related nodes in a dedicated file for
stm32mp15
- ARM: dts: stm32: fix pwr regulators references to use scmi
- ARM: dts: stm32: use the correct clock source for CEC on stm32mp151
- ARM: dts: stm32: DSI should use LSE SCMI clock on DK1/ED1 STM32 board
- ARM: dts: stm32: delete fixed clock node on STM32MP15-SCMI
- ARM: dts: stm32: add missing usbh clock and fix clk order on stm32mp15
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add the uclass ops of_to_plat to parse the device tree properties
to respect the expected sequence by the driver model.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
All the elements of privdata are static and build from device tree,
they are moved in platdata to prepare the support of ops
of_to_plat.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Rename stm32_sdmmc_bind to stm32_sdmmc2_bind as all other functions
in SDMMCv2 driver
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change-Id: Ic51acdfbbba6e971809c1029dd2227038bfe879d
|
|
Add the node for SCMI firmware with the associated reserved memory nodes
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add the node for OP-TEE firmware with the associated reserved memory nodes
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Correctly handle STM32MP_BOARD_EXTRA_ENV define in stm32mp15_st_common.h;
the STM32MP_BOARD_EXTRA_ENV is added in CONFIG_EXTRA_ENV_SETTINGS
definition, as it is done "stm32mp15_st_common.h"
Without this patch, the content of STM32MP_BOARD_EXTRA_ENV is not used in
the default environment for STMicroelectronics boards.
Fixes: 806c4dd31532 ("configs: stm32mp1: set the console variable for extlinux.conf")
Reported-by: Gatien CHEVALLIER <gatien.chevallier@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Another small round of CONFIG migrations to Kconfig
|
