| Age | Commit message (Collapse) | Author |
|---|
|
rk3399-nanopi-4.dtsi try to set parent of and set rate to 100 MHz of the
SCLK_PCIEPHY_REF clock.
The existing enable/disable ops for SCLK_PCIEPHY_REF currently force
use of 24 MHz parent and rate.
Add improved support for setting parent and rate of the pciephy refclk
to driver to better support assign-clock props for pciephy refclk in DT.
This limited implementation only support setting 24 or 100 MHz rate,
and expect npll and clk_pciephy_ref100m divider to use default values.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
rk3399.dtsi from linux v5.19 and newer try to set VDU clock rate to
400 MHz using an assigned-clock-rates prop of the CRU node.
U-Boot does not use or need this clock so add dummy support for getting
and setting ACLK_VDU clock rate to allow CRU driver to be loaded with an
updated rk3399.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Sync rk3399-cru.h with one from Linux kernel v6.2+ and fix use of the
SCLK_DDRCLK name that was only used by U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
A few boards have shown to be required to properly configure pinctrl
for the fixed regulator gpio pin used by sdmmc before being able to read
from SD-cards.
Include the related gpio, regulator and pinctrl nodes and enable related
Kconfig options so that pinctrl can be configured in SPL for boards that
may be affected by such issue.
Also change to imply SPL_DM_SEQ_ALIAS for all boards because it must be
enabled for working gpio usage in SPL after a future DT sync.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
When RK3399 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there can be a fallback
to read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card may fail:
U-Boot SPL 2024.04-rc4 (Mar 17 2024 - 22:54:45 +0000)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Card did not respond to voltage select! : -110
mmc_init: -95, time 12
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
Fix this by tagging related sdhci, sdmmc and spi flash pinctrl nodes
with bootph props. Also move bootph for common nodes shared by all
boards to the SoC u-boot.dtsi.
eMMC, SD-Card and SPI flash nodes are also changed to only be tagged
with bootph props for SPL and U-Boot pre-reloc phases.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The initial serial console UART iomux is typically configured in
board_debug_uart_init() at TPL stage on Rockchip platform.
Later stages typically use pinctrl driver to configure iomux UART once
again based on the control FDT.
Include uart related pinctrl nodes in TPL/SPL control FDT to make it
possible for pinctrl driver to configure UART iomux at TPL/SPL stage.
Following debug log message may also be seen at U-Boot pre-reloc stage:
ns16550_serial serial@ff1a0000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
This can be resolved by including bootph prop for U-Bood pre-reloc
phase (bootph-some-ram or bootph-all). However, this has intentionally
been excluded due to including it unnecessarily slows down boot around
200-400 ms.
Also add the clock-frequency prop similar to what has been done for
other Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
rk3399-puma is the only supported board that use uart0 for serial
console, other RK3399 boards typically use uart2 for serial console
and may use uart0 for bluetooth.
Move setting bootph prop to board u-boot.dtsi to only include the uart0
node in TPL/SPL control FDT for the rk3399-puma target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The vop nodes should not be included in TPL/SPL control FDT, it should
only be included at U-Boot proper pre-reloc phase.
Change to use bootph-some-ram prop to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Sort nodes alphabetically by name, symbol or reg addr in RK3399 related
u-boot.dtsi files. Also remove one of the duplicated &pmu nodes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Remove superfluous bootph-all props already inherited from main soc
u-boot.dtsi file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
A lot of RK3399 boards use a u-boot,spl-boot-order of "same-as-spl",
&sdhci and &sdmmc.
Move this to rk3399-u-boot.dtsi and make this default for boards
currently missing a u-boot,spl-boot-order prop.
Before commit a7e69952eb6d ("rockchip: spl: Cache boot source id for
later use") it was required to include the SPI flash node in the
u-boot,spl-boot-order prop to successfully load FIT from SPI flash.
The SPI flash node reference has been dropped from spl-boot-order from
pinebook-pro, roc-pc and rockpro64 now that "same-as-spl" also gets
resolved to the SPI flash node and loading FIT from SPI flash works
without having the node explicitly referenced in spl-boot-order prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The TPL and/or SPL control FDT on RK3399 boards does not contain any
node with a compatible that is supported by driver/misc/ drivers.
Remove use of xPL_MISC_DRIVERS options to stop including e.g an unused
efuse driver in TPL and/or SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Imply OF_LIBFDT_OVERLAY Kconfig options to add device tree overlay
support on all RK3399 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
|
|
Imply support for GbE PHY status parsing and configuration when support
for onboard ethernet is enabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
|
|
The RK3399 SoC contain a crypto engine block that can generate random
numbers.
Imply DM_RNG and RNG_ROCKCHIP Kconfig options to take advantage of the
random generator on all RK3399 boards. Also remove the unnecessary use
of a status = "okay" prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
|
|
The RK3399 SoC support the ARMv8 Cryptography Extensions, use of ARMv8
crypto can speed up FIT checksum validation in SPL.
Imply ARMV8_SET_SMPEN and ARMV8_CRYPTO to take advantage of the crypto
extensions for SHA256 when validating checksum of FIT images.
Imply SPL_FIT_SIGNATURE and LEGACY_IMAGE_FORMAT to enable FIT checksum
validation to almost all RK3399 boards.
The following boards have been excluded:
- chromebook_bob: SPL max size limitation of 120 KiB
- chromebook_kevin: SPL max size limitation of 120 KiB
Also imply OF_LIVE to help speed up init of U-Boot proper and disable
CONFIG_SPL_RAW_IMAGE_SUPPORT on leez-rk3399 to ensure SPL does not try
to jump to code that failed checksum validation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Sort imply statements under ROCKCHIP_RK3399 alphabetically.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
|
|
The rk3399-ficus board is only using SPL and not TPL+SPL like all other
RK3399 boards, chromebook bob/kevin excluded. It does not seem to be any
technical reason why this board was left using only SPL.
Switch to use TPL+SPL and to use the common bss and stack addresses
introduced in commit 008ba0d56d00 ("rockchip: Add common default bss and
stack addresses"). Also add the missing DEFAULT_FDT_FILE option.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The rk3399-puma board is currently using SPL stack and bss addr in SRAM,
the same addr typically used by TPL, this differs from most other RK3399
boards.
Switch to use the common bss and stack addresses introduced in commit
008ba0d56d00 ("rockchip: Add common default bss and stack addresses").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
On rk3399-puma the FIT payload is located at sector 0x200 compared
to the more Rockchip common sector 0x4000 offset:
SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x200
Because FIT payload is located at sector 0x200 and IDBlock is located at
sector 64, the combined size of TPL+SPL (idbloader.img) cannot take up
more than 224 KiB:
(0x200 - 64) x 512 = 0x38000 (224 KiB)
Adjust SPL_PAD_TO to match the used 0x200 sector offset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Chromebook bob and kevin typically run coreboot as the initial boot
loader, however, U-Boot proper can be used as a secondary boot loader.
It is also possible to run U-Boot SPL and proper bare metal, with SPL
and the U-Boot payload loaded from SPI flash.
Because of this chromebook bob and kevin only use SPL and not TPL+SPL
like other RK3399 boards, this mean that SPL is loaded to and run from
SRAM instead of DRAM.
The U-Boot payload is located at 0x40000 (256 KiB) offset in SPI flash
and because the BROM only read first 2 KiB for each 4 KiB page, the size
of SPL (idbloader.img) is limited to max 128 KiB.
The chosen bss start address further limits the size of SPL to 120 KiB.
0xff8e0000 (SPL_BSS_START_ADDR) - 0xff8c2000 (SPL_TEXT_BASE) = 0x1e000
Update SPL_MAX_SIZE to reflect the 120 KiB max size limitation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/20614
- Add SPL variant of DM_RNG so that the DM_RNG can be disabled in SPL if
necessary. This may be necessary due to e.g. size constraints of the SPL.
- dd SPL variant of SPL_FSL_CAAM_RNG so that the SPL_FSL_CAAM_RNG can be
disabled in SPL if necessary. This may be necessary due to e.g. size
constraints of the SPL.
- Differentiate between CAAM and DCP in Kconfig entry.
|
|
Differentiate between "Enable Random Number Generator support" and
"Enable Random Number Generator support" in Kconfig entry, mark the
first as CAAM and the second as DCP, otherwise users cannot easily
decide which of the options is which and enable the correct one.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Add SPL variant of SPL_FSL_CAAM_RNG so that the SPL_FSL_CAAM_RNG can
be disabled in SPL if necessary. This may be necessary due to e.g.
size constraints of the SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Add SPL variant of DM_RNG so that the DM_RNG can be disabled in SPL
if necessary. This may be necessary due to e.g. size constraints of
the SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
- Typo fixes, gpt command fix, a few npcm fixes, fix a reported Coverity
issue and increase the malloc pool on am62x_evm_r5 to fix some use
cases.
|
|
Joel is no longer with Broadcom. Remove his email from bcmbca maintainer
list and replace him with myself for stack protection maintainer.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
|
|
On AM62x SK we can see a boot failure with signature "alloc space
exhausted", so fix by increasing size of SPL_STACK_R_MALLOC_SIMPLE_LEN.
Fixes: 128f81290b ("arm: dts: k3: binman: am625: add support for signing TIFSSTUB Images")
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
|
|
Fix a typo, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
For 4GB dram size, the dram is divided into 2 banks and
the address space of these 2 banks are not concatenated.
Limit the gd->ram_top to not exceed bank0 top to prevent
accessing invalid memory region.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
When u-boot enable CONFIG_SYS_BOOT_RAMDISK_HIGH, rootfs image relocated
from FIU address space to memory address before jump to kernel.
Since Arbel reserved memory from 0x00000000 to 0x06200000 for tip image,
and rootfs image may too large that cannot found a suitable location
before 128MB(0x8000000), so increase mapping size from 128MB to 192MB.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
Add mem and console env information and modify the wrong earlycon env.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
When parsing option 40 (network information service domain) the
option length is in variable 'oplen' and not in 'size'.
Addresses-Coverity-ID: 492765 Uninitialized variables (UNINIT)
Fixes: 8ab388bfdbcf ("net: add support to parse the NIS domain for the dhcp options")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Reset HW to clear old status and use default data mode(8-bit).
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
Change in v2:
- Fix applies to all block devices, not just MMC.
If partition init is not completed within the gpt write,
the gpt partition list will not be updated.
Signed-off-by: Kishan Dudhatra <kishan.dudhatra@siliconsignals.io>
|
|
%s/arguemnts/arguemnts/
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
%s/arguemnts/arguments/
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Commit 37cb626da25d0d ("mmc: sdhci: Add Support for ADMA2") introduced
ADMA_DESC_LEN == 16 (64 bit case), but it was never used before commit
74755c1fed1b0 ("mmc: sdhci: introduce adma_write_desc() hook to struct sdhci_ops").
"sizeof(struct sdhci_adma_desc)" (== 12 for 64bit case) was used instead.
Confusion probably originates from Linux commit 685e444bbaa0
("mmc: sdhci: Add ADMA2 64-bit addressing support for V4 mode"), but
the latter "V4 mode" was never ported to U-Boot.
Fixes: 74755c1fed1b0 ("mmc: sdhci: introduce adma_write_desc() hook to struct sdhci_ops")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>
Tested-by: Judith Mendez <jm@ti.com>
|
|
CI: https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/20596
- RISC-V: cmd: Add SBI implementation ID and extension ID
- Board: Rename spl_soc_init to spl_dram_init
- Board: milkv_duo: Add SPI NOR flash, Ethernet, Sysreset support
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2024-07-rc2
Documentation:
* correct description of 'env print -e'
UEFI:
* remove superfluous efi_restore_gd after EFI_CALL
* terminate efidebug test bootmgr early on error
* do not install device-tree if bootmgr fails
* pass GUID by address to efi_dp_from_lo
* remove dead code in efi_var_mem_init()
* enable QueryVariableInfo at runtime for file backed variables
|
|
Rename spl_soc_init() to spl_dram_init() because the generic function
name does not reflect what the function actually does. Also
spl_dram_init() is commonly used for dram initialization and should be
called from board_init_f().
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Rename spl_soc_init() to spl_dram_init() because the generic function
name does not reflect what the function actually does. Also
spl_dram_init() is commonly used for dram initialization and should be
called from board_init_f().
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Add configs related to spi nor flash for Sophgo Milk-V Duo board
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Add spi nor flash controller node for cv18xx SoCs
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Add spi nor flash controller driver for cv1800b SoC
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Add configs related to ethernet and ethernet boot command for Sophgo Milk-V
Duo board
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Add ethernet node for cv1800b SoC
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Initialize register in cv1800b ethernet phy to make it compatible with
generic phy driver
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Let the sbi command detect the coreboot and oreboot SBI Implementation IDs
defined in SBI specification v2.0.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
