summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2023-11-28board: Move show_board_info() comment to header fileSimon Glass
Move this comment to its prototype and tidy it up a bit. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2023-11-12power: regulator: add AXP313 supportAndre Przywara
The X-Powers AXP313a is a small PMIC with just three buck converters and three LDOs, one of which is actually fixed (so not modelled here). Add the compatible string and the respective regulator ranges to allow drivers to adjust voltages. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2023-11-12power: pmic: sunxi: add AXP313 SPL driverAndre Przywara
On boards using the AXP313 PMIC, the DRAM rail is often not setup correctly at reset time, so we have to program the PMIC very early in the SPL, before running the DRAM initialisation. Add a simple AXP313 PMIC driver that knows about DCDC2(CPU) and DCDC3(DRAM), so that we can bump up the voltage before the DRAM init. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
2023-11-12arm: dts: icnova-a20-adb4006: Add board supportLudwig Kormann
Add board support for ICnova A20 SomPi compute module on ICnova ADB4006 development board. Specification: SoM - Processor: Allwinner A20 Cortex-A7 Dual Core at 1GHz - 512MB DDR3 RAM - Fast Ethernet (Phy: Realtek RTL8201CP) ADB4006 - I2C - 2x USB 2.0 - 1x Fast Ethernet port - 1x SATA - 2x buttons (PWRON, Boot) - 2x LEDS - serial console - HDMI - µSD-Card slot - Audio Line-In / Line-Out - GPIO pinheaders https://wiki.in-circuit.de/index.php5?title=ICnova_ADB4006 https://wiki.in-circuit.de/index.php5?title=ICnova_A20_SODIMM devicetree upstreamed with linux 6.5 Signed-off-by: Ludwig Kormann <ludwig.kormann@ict42.de> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2023-11-12pinctrl: sunxi: Avoid using .bss for SPLSamuel Holland
sunxi platforms put .bss in DRAM, so .bss is not available in SPL before DRAM controller initialization. Therefore, this buffer must be placed in the .data section. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2023-11-12sunxi: mmc: Sort compatible strings numericallySamuel Holland
commit 95168d77d391 ("sunxi: add Allwinner R528/T113 SoC support") added the new entry out of order. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2023-11-12clk: sunxi: Use the right symbol in the MakefileSamuel Holland
CONFIG_ARCH_SUNXI will not be enabled for RISC-V SoCs using this driver. Use the symbol for the driver itself instead. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2023-11-12sunxi: mmc: Move header to the driver directorySamuel Holland
The MMC controller driver is (and ought to be) the only user of these register definitions. Put them in a header next to the driver to remove the dependency on a specific ARM platform's headers. Due to the sunxi_mmc_init() prototype, the file was not renamed. None of the register definitions were changed. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2023-11-12net: sun8i_emac: Drop DM_GPIO checksSamuel Holland
DM_GPIO is always enable in U-Boot proper for ARCH_SUNXI, and this driver is never enabled in SPL, so the condition is always true. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2023-11-12arm: sunxi: Correct warning in board_fit_config_name_matchTom Rini
When building this with clang, we get a warning about having excess parenthesis here, or that we're incorrectly using "==" when we want "=". Correct these by using the common size macro. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> [Andre: Use SZ_512M as per Simon's suggestion] Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2023-11-12sunxi: board: simplify early PMIC setup conditionsAndre Przywara
So far we have a convoluted #ifdef mesh that guards the early AXP PMIC setup in board.c. That combination of &&, || and negations is very hard to read, maintain and especially to extend. Fortunately we have those same conditions already modelled in the Kconfig file, so they are actually redundant. On top of that the real reason we have those preprocessor guards in the first place is about the symbols that are *conditionally* defined: without #ifdefs the build would break because of them being undefined for many boards. To simplify this, just change the guards to actually look at the symbols needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER. This drastically improves the readability of this code, and makes adding PMIC support a pure Kconfig matter. Doing this revealed one bug in Kconfig: there is no axp_set_dcdc4() for the AXP818, even though CONFIG_AXP_DCDC4_VOLT includes that PMIC. Since the AXP818 wasn't included when calling axp_set_dcdc4() in board.c, this wasn't an issue, but becomes one now, so also remove the AXP818 from the DCDC4 Kconfig symbol. Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2023-11-10Merge patch series "arm: dts: k3-am6: Fix Ethernet/DMA"Tom Rini
To quote the author: Since commit [1], Ethernet is broken on TI AM62 and AM64 platforms. The commit [1] is not the culprit. It just unearths the problem by fixing the error check in k3-udma.c. This issue was silently being ignored earlier due to wrong error check. [NULL instead of FDT_ADDR_T_NONE]. Fix the issue by adding the necessary register spaces for the u-boot K3-UDMA driver for AM62 and AM64 platforms. These properties will eventually make it into the SoC DTSi files [2] after which these can be dropped from k3-*-u-boot.dtsi files. [1] - 5fecea171de3dd ("treewide: use dev_read_addr_*_ptr() where appropriate") [2] - https://lore.kernel.org/linux-arm-kernel/20230810174356.3322583-1-vigneshr@ti.com/
2023-11-10arm: dts: k3-am642: Update main_bcdma and main_pktdma nodesSiddharth Vadapalli
Update main_bcdma and main_pktdma nodes for native configuration in the absence of DM services. Drop duplicate main_pktdma node in k3-am642-sk-u-boot.dtsi. Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Signed-off-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Nishanth Menon <nm@ti.com>
2023-11-10arm: dts: k3-am625-verdin-wifi-dev-u-boot.dtsi: Fix DMA/EthernetRoger Quadros
Update main_bcdma and main_pktdma nodes for native configuration in the absence of DM services. u-boot k3-udma driver expects these additional register fields else probe will fail. Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Nishanth Menon <nm@ti.com> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2023-11-10arm: dts: k3-am625-sk-u-boot.dtsi: Update main_bcdma and main_pktdma nodesSiddharth Vadapalli
Update main_bcdma and main_pktdma nodes for native configuration in the absence of DM services. Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Signed-off-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Nishanth Menon <nm@ti.com>
2023-11-10Merge tag 'u-boot-stm32-20231110' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-stm _ Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled _ Fix issue following DT sync with kernel 6.3 for stm32mp15xx-ev1 and DHSOM SoM _ Enable TCP, IPv6, wget on DH STM32MP15 DHSOM _ Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOM _ Read auth stats and boot_partition from tamp
2023-11-10Merge branch '2023-11-10-assorted-fixes'Tom Rini
- Fix some issues Coverity has reported, update MAINTAINERS file, another bootstd fix, typo fix in error message, gitignore fix and update TI's URL in many places.
2023-11-10boot: Fix syntax in fdt_overlay_apply_verbose() error messageHugo Villeneuve
Remove superfluous "did". Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
2023-11-10tools: gitignore: Fix tools/generated pathSam Protsenko
'git status' shows 'tools/generated/' after running the build, which is wrong. The corresponding .gitignore rule was already added in commit c623642d29be ("Adjust gitignore for tools/generated/"), but because of superfluous 'tools/' part it wasn't in effect. Remove incorrect 'tools/' part to fix it. While at it, remove tools/ path incorrectly added to the top-level .gitignore in commit 801c482207c7 (".gitignore: ignore misc include, simple-bin, and tools/generated build artifacts"), as it's required in the comment on the top of .gitignore: # NOTE! Don't add files that are generated in specific # subdirectories here. Add them in the ".gitignore" file # in that subdirectory instead. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Fixes: c623642d29be ("Adjust gitignore for tools/generated/") Fixes: 801c482207c7 (".gitignore: ignore misc include, simple-bin, and tools/generated build artifacts")
2023-11-10bootstd: Skip over bad device during bootflows scanningTony Dinh
During bootstd scanning for bootdevs, if bootdev_hunt_drv() encounters a device not found error (e.g. ENOENT), let it return a successful status so that bootstd will continue scanning the next devices, not stopping prematurely. Background: During scanning for bootflows, it's possible for bootstd to encounter a faulty device controller. Also when the same u-boot is used for another variant of the same board, some device controller such as SATA might not exist. I've found this issue while converting the Marvell Sheevaplug board to use bootstd. This board has 2 variants, the original Sheevaplug has MMC and USB only, but the later variant comes with USB, MMC, and eSATA ports. We have been using the same u-boot (starting with CONFIG_IDE and later with DM CONFIG_SATA) for both variants. This worked well with the old envs-scripting booting scheme. Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2023-11-10tree-wide: Replace http:// link with https:// link for ti.comNishanth Menon
Replace instances of http://www.ti.com with https://www.ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
2023-11-10test: cmd: mbr: Remove unreachable codeAlexander Gendin
Fix an issue reported by Coverity scan, and fix code indentation. Addresses-Coverity-ID: 467404 ("Control flow issues (DEADCODE)") Signed-off-by: Alexander Gendin <agendin@matrox.com>
2023-11-10firmware: scmi: correct a validity check against power domain idAKASHI Takahiro
A power domain id on sandbox should be in the range from zero to ARRAY_SIZE(scmi_pwdom) - 1. Correct the validity check logic. Addresses-Coverity-ID: 467401 ("Out-of-bounds write") Addresses-Coverity-ID: 467405 ("Out-of-bounds read") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2023-11-10scsi: Have scsi_init_dev_desc_priv() use memsetTom Rini
When we do not have CONFIG_BOUNCE_BUFFER enabled, inside of scsi_init_dev_desc_priv we never set the 'bb' field to false, we only initialize it to true when CONFIG_BOUNCE_BUFFER is set. Given that we have a number of other fields here we had been explicitly setting to zero, change to first calling memset to clear the struct and then initialize only the fields that need non-zero default values. Addresses-Coverity-ID: 467407 ("Uninitialized variables (UNINIT)") Fixes: 81bd22e935dc ("rockchip: block: blk-uclass: add bounce buffer flag to blk_desc") Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2023-11-10Merge tag 'u-boot-rockchip-20231110' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-rockchip - Add Board: rk3588 Pine64 QuartzPro64; - Fix rk3066 enter download mode; - Fix for ringneck-px30 board;
2023-11-10rockchip: include: asm: fix entering download mode rk3066Johan Jonker
Keep track of the re-entries with help of the lr register. This binary can be re-used and called from various BROM functions. Only when it's called from the part that handles SPI, NAND or EMMC hardware it needs to early return to BROM ones. In download mode when it handles data on USB OTG and UART0 this section must be skipped. Unlike newer Rockchip SoC models the rk3066 BROM code does not have built-in support to enter download mode on return to BROM. This binary must check the boot mode register for the BOOT_BROM_DOWNLOAD flag and reset if it's set. It then returns to BROM to the end of the function that reads boot blocks. From there the BROM code goes into a download mode and waits for data on USB OTG and UART0. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-11-10rockchip: ringneck-px30: enable SPL_BOARD_INITQuentin Schulz
Now that Ringneck requires some board-specific code (namely resetting the MCU companion controller) to be run during SPL stage, let's enable SPL_BOARD_INIT. Cc: Quentin Schulz <foss+uboot@0leil.net> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-11-10rockchip: ringneck-px30: always reset STM32 companion controller on bootQuentin Schulz
It's happened that glitches on the STM32_RST and STM32_BOOT lines have put the STM32 companion microcontroller into DFU mode making it not boot its FW, rendering it useless for the user. Considering that the STM32 companion microcontroller is always reset on a reboot or power cycle, resetting it once again in U-Boot SPL isn't going to hurt it any more. For ATtiny companion microcontroller, the situation is a bit different because a reboot or power cycle doesn't reset it. Additionally, since it can only be reset with a UPDI reset on the STM32_RST line, and that is virtually impossible to mistakenly trigger, the ATtiny is unlikely to be in unwanted reset or enter reset because U-Boot toggles STM32_RST line. Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-11-10rockchip: rv1126: Read cpuid from otp and set ethaddrTim Lunn
Provide configuration to read cpuid and generate a persistent MAC address in ethaddr Signed-off-by: Tim Lunn <tim@feathertop.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-11-10rockchip: otp: Add support for RV1126Tim Lunn
Extend the otp driver to read rv1126 otp. This driver code was adapted from the Rockchip BSP stack. Signed-off-by: Tim Lunn <tim@feathertop.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-11-10rockchip: dts: fix bootph tags for rv1126Tim Lunn
RV1126 fails to boot on 2024.01-rc1. Commit 9e644284ab81 ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation") changed the behaviour of bootph-pre-ram, to limit nodes to spl phase. This caused rv1126 boards to fail to boot with the current dts. This patch updates the pmu/grf nodes to bootph-all tags as they are needed in all phases. This fixes the boot issue on rv1126 boards. Signed-off-by: Tim Lunn <tim@feathertop.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-11-10MAINTAINERS: Fix Sam Protsenko mailSam Protsenko
Sam works for Linaro again. Use his work e-mail address for ANDROID AB subsystem. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2023-11-10stm32mp1: read auth stats and boot_partition from tampIgor Opaniuk
Obtain from TAMP backup register information about image authorization status and partition id used for booting. Store this info in environmental variables ("boot_auth" and "boot_part" correspondingly). Image authorization supported values: 0x0 - No authentication done 0x1 - Authentication done and failed 0x2 - Authentication done and succeeded These values are stored to TAMP backup register by Trusted Firmware-A [1]. Testing: STM32MP> print boot_part boot_part=1 STM32MP> print boot_auth boot_auth=2 [1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?h=refs/heads/integration&id=ab2b325c1ab895e626d4e11a9f26b9e7c968f8d8 Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2023-11-10arm: stm32: Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOMMarek Vasut
The maximum size of u-boot.itb in SPI NOR on DH STM32MP15 DHSOM is 0x160000 . Define this size in U-Boot config to prevent misconfigured builds from emitting larger u-boot.itb than the one which fits the SPI NOR area reserved for the blob. The SPI NOR layout is as follows: 0x00_0000..0x03_ffff ... SPL 1 0x04_0000..0x07_ffff ... SPL 2 0x08_0000..0x1d_ffff ... U-Boot 0x1e_0000..0x1e_ffff ... Environment 1 0x1f_0000..0x1f_ffff ... Environment 2 Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2023-11-10arm: stm32: Enable TCP, IPv6, wget on DH STM32MP15 DHSOMMarek Vasut
Enable support for TCP protocol, wget, and IPv6 on this platform. The former two allow users download payload into the U-Boot from a web server, which may be more convenient or easier to set up than TFTP server. The later is enabled to future proof the IP stack on this platform. Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2023-11-10ARM: dts: stm32mp: Repair damage from alignment with v6.3Marek Vasut
The patch fixed by this commit renders ST STM32MP15xx EV1 board and all DHSOM SoM based boards unbootable from SPI NOR. Fix the damage by updating -u-boot.dtsi to match the stm32mp15-pinctrl.dtsi update. Fixes: 08002ffd083d ("ARM: dts: stm32mp: alignment with v6.3") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2023-11-10arm: stm32mp: Really fix compilation issue when SYS_DCACHE_OFF and/or ↵Bhupesh Sharma
SYS_DCACHE_SYS are enabled While 23e20b2fa6 ("arm: stm32mp: Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled") tried fixing this issue, fix it really by adding #if checks for SYS_ICACHE_OFF and SYS_DCACHE_OFF. Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2023-11-09rockchip: ringneck-px30: enable i2c commandQuentin Schulz
This is a useful tool to check the presence of a device on a specific i2c bus, so let's enable it. Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-11-09board: rockchip: add Pine64 QuartzPro64 RK3588 boardTom Fitzhenry
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64. UART and boot over SD/eMMC/RJ45 are tested to work. Linux commits from next-20231013: 8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree") Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Cc: Eugen Hristev <eugen.hristev@collabora.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Ondrej Jirman <megi@xff.cz>
2023-11-07Merge tag 'xilinx-for-v2024.01-rc3' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-microblaze Xilinx changes for v2024.01-rc3 xilinx: - Disable lock in mini spi configurations zynq: - DTS syncups - Kconfig updates zynqmp: - DTS syncups - Kconfig fixups versal: - Make 30MHz as default freq for spi versal net: - Enable ADMA for mmc serial: - Read baudrate from DT spi: - Put spi lock under one Kconfig - Support 64bit addresses in cadance_ospi - zynqmp_gqspi - change logging support firmware: - Handle errors in zynqmp_pm_feature() include: - Sync vsc8531 dt binding with kernel
2023-11-07MAINTAINERS: fastboot: add MattijsMattijs Korpershoek
Fastboot has been marked as orphaned since 2021. Since I'm interested in maintaining this, assign myself. Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Lukasz Majewski <lukma@denx.de>
2023-11-07MAINTAINERS: usb gadget: add MattijsMattijs Korpershoek
It seems that Lukasz and Marek could get some help in maintaining the usb gadget drivers. Assign myself as maintainer. Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Lukasz Majewski <lukma@denx.de>
2023-11-07dt-bindings: Remove VSC8531 specific RGMII delay definitionsMichal Simek
Based on Linux upstream discussion value enumeration shouldn't be used. Instead of it delay in pS should be used that's why remove it from the header. Link: https://lore.kernel.org/all/YNsm%2F0dmpBgO8mqr@lunn.ch/ Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/bbd343474856a67252f3b31d22b3b5a80ad04043.1698851109.git.michal.simek@amd.com
2023-11-07arm64: zynqmp: Add description for nvmem efuse layoutMichal Simek
Based on discussion with DT folks at link below there is not going to be any name restrictions for child names. That's why add description for current nvmem layout. Link: https://lore.kernel.org/lkml/20231013101450.573-3-praveen.teja.kundanala@amd.com/ Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/af81299cafc2bd13ed30dcd69bdf6efb5fbb7f68.1698840373.git.michal.simek@amd.com
2023-11-07ARM: zynq: Add partition descriptionMichal Simek
Xilinx is using standard mtd partition layout for quite a long time. It is used for testing purpose on evaluation boards. Also #address/size-cells shouldn't be present without nodes which should use them that's why move them from zynq-7000.dtsi to nand/nor nodes directly. The patch was tested on zc706 and zedboard(with also increasing max frequency and rx bus width). Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/4c3348981bba32d3892194420d78fe8621c47534.1698837725.git.michal.simek@amd.com
2023-11-07xilinx: Enable SPI_FLASH_MTD by defaultMichal Simek
Provide access to qspi flash layout via mtd command. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/b3c4a3eddb71aab9535b034380d0dbae770828d4.1698837725.git.michal.simek@amd.com
2023-11-07arm64: zynqmp: Comment all smmu entriesMichal Simek
SMMU is disabled by default and not all masters can be enabled at the same time because of limited number of entries. That's why comment all iommu properties but keep them for reference in DT. In XEN case they should be added back and Xen should have SMMU enabled by default. Also add IDs for DP and DPDMA. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/e868c27c52ded5d8ef25f75ba394b1ab3b31b80a.1698825657.git.michal.simek@amd.com
2023-11-07arm64: versal-net: Add DTSes for mini qspi/ospi configurationMichal Simek
Mini U-Boot is running out of OCM and it's only purpose is to program non volatile memories. There are different configurations which ospi/qspi can be that's why describe them via DT. DT binding is already approved that's why there is no reason not to add it. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/a99a8d72201a782fc811715942dea97fb5ab583b.1698329087.git.michal.simek@amd.com
2023-11-07arm64: versal: Add DTSes for mini qspi/ospi configurationMichal Simek
Mini U-Boot is running out of OCM and it's only purpose is to program non volatile memories. There are different configurations which ospi/qspi can be that's why describe them via DT. DT binding is already approved that's why there is no reason not to add it. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/9518ab1c4299a45e800b8611172edd78c9243132.1698329087.git.michal.simek@amd.com
2023-11-07ARM: zynq: Add DTSes for mini qspi configurationsMichal Simek
Mini U-Boot is running out of OCM and it's only purpose is to program non volatile memories. There are different configurations which qspi can be that's why describe them via DT. DT binding is already approved that's why there is no reason not to add it. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/e7d31a9d9c4a76e171eefc619f31fabd0831a614.1698329087.git.michal.simek@amd.com
generated by cgit v1.2.3 (git 2.0.4) at 2025-08-01 18:14:02 +0000