| Age | Commit message (Collapse) | Author |
|---|
|
tkuw584924@gmail.com <tkuw584924@gmail.com> says:
From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
The S25FS064S, S25FS128S, and S25FS256S are the same family of SPI NOR
Flash devices with S25FS512S.
Datasheets:
https://www.infineon.com/dgdl/Infineon-S25FS064S_64_Mb_8_MB_FS-S_Flash_SPI_Multi-I_O_1-DataSheet-v10_00-EN.pdf?fileId=8ac78c8c7d0d8da4017d0ed526b25412
https://www.infineon.com/dgdl/Infineon-S25FS128S_S25FS256S_1.8_V_Serial_Peripheral_Interface_with_Multi-I_O_MirrorBit(R)_Non-Volatile_Flash-DataSheet-v15_00-EN.pdf?fileId=8ac78c8c7d0d8da4017d0ed6b5ab5758
|
|
The S25FS064S, S25FS128S, and S25FS256S are the same family of SPI NOR
Flash devices with S25FS512S. Some difference depending on the device
densities are taken care in post SFDP fixup.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
|
|
The 6th ID byte is needed to distiguish S25FL-S and S25FS-S families.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
The correct 4KB erase opcode should be selected based on the address width
currently used.
Fixes: 562d166a13 ("mtd: spi-nor-core: Add fixups for s25fs512s")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
The w25q16cl does support locking the same way w25q16dw does,
fill in the missing flags.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
The mx25u25635f entry exists twice in spi_nor_ids, remove the less
complete variant of the entry and keep only one copy of it.
Fixes: f0084f1dfdbc ("drivers/mtd/spi/spi-nor-ids.c: add mx25u25635f support")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
|
|
The w25q16dw entry exists twice in spi_nor_ids, remove the less
complete variant of the entry and keep only one copy of it.
Fixes: baef13ec9d59 ("mtd: spi-nor-ids: Add support for flashes tested by xilinx")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
|
|
Some Winbond SPI NORs have special SR3 register which is
used among other things to control whether non-standard
"Individual Block/Sector Write Protection" (WPS bit)
locking scheme is activated. This non-standard locking
scheme is not supported by either U-Boot or Linux SPI
NOR stack so make sure it is disabled, otherwise the
SPI NOR may appear locked for no obvious reason.
This SR3 WPS appears e.g. on W25Q16FW which has the same ID as
W25Q16DW, but the W25Q16DW does not implement the SR3 WPS bit.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2025-01-rc1
Documentation:
* Move the generic memory-documentation to doc/
* Fix typo boormethod
UEFI:
* Delete rng-seed if having EFI RNG protocol
* Don't call restart_uboot in EFI watchdog test
* Simplify building EFI binaries in Makefile
* Show FirmwareVendor and FirmwareRevision in helloworld
* Add debug output for efi bootmeth
Other:
* CONFIG_CMD_CLK should depend on CONFIG_CLK
* simplify clk command
* enable clk command on the sandbox
|
|
Enabling the clk command on the sandbox will allow us to write tests
for it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
CONFIG_DM is always true.
The clk command is only built if CONFIG_CLK=y.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
The clk command cannot provide useful output without a clock driver.
So let it depend on CONFIG_CLK.
Since commit 258c1002383e ("cmd: clk: Use dump function from clk_ops")
the remark about deprecation is obsolete. Remove it.
Since commit 7ab418fbe612 ("clk: add support for setting clk rate from
cmdline") the clk command can be used to set clock frequencies. Mention
it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
%s/boormethod/bootmethod/
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
|
|
Calling u_boot_console.restart_uboot() in
test_efi_selftest_watchdog_reboot() may lead to incorrect results.
While the watchdog triggered reboot is running thee test environment may
need some time before triggering a reboot itself. This may lead to
duplicate output of the U-Boot greeter which is recorded as an error.
Reported-by: Tom Rini <trini@konsulko.com>
Fixes: df172e117d1d ("test/py: test reboot by EFI watchdog")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Add a little debugging so we can see what is happening.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Show the firmware vendor and revision to make it clear which firmware is
used, e.g. whether U-Boot is providing the boot services.
The output will look like
Firmware vendor: Das U-Boot
Firmware revision: 20241000
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Add a way to factor out the CFLAGS changes for each app, since they are
all the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
We have quite a few apps now, so create a way to specify them as a list
rather than repeating the same rules again and again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
The link rule (for $(obj)/%_efi.so) in scripts/Makefile.lib handles
pulling in efi_crt0.o and efi_reloc.o so drop the 'extra' rules.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
This is not actually a command so the name is confusing. Use
BOOTEFI_HELLO_COMPILE instead. Put it in the efi_loader directory
with the other such config options.
The link rule (for $(obj)/%_efi.so) in scripts/Makefile.lib handles
pulling in efi_crt0.o and efi_reloc.o so drop the 'extra' rules.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Move this section of the README into doc/ with some minor updates to
mention SPL and user lower-case hex.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
For measured be boot we must avoid any volatile values in the device-tree.
We already delete /chosen/kaslr-seed if we provide and EFI RNG protocol.
Additionally remove /chosen/rng-seed provided by QEMU or U-Boot.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
CONFIG_DM_SPI depends on CONFIG_DM. There is no need to list CONFIG_DM
explicitly as dependency for CONFIG_DM_SPI_FLASH
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Link: https://lore.kernel.org/r/20240604044039.27795-1-heinrich.schuchardt@canonical.com
|
|
John Watts <contact@jookia.org> says:
I'm doing some SPI work so I tried to compile all the drivers on my
sunxi board to try and avoid some regressions. This failed, so here are
some fixes for this.
Link: https://lore.kernel.org/r/20240427-spikconfig-v1-0-8a54772522f4@jookia.org
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This is required for compiling.
Signed-off-by: John Watts <contact@jookia.org>
|
|
This code uses dev_err which is defined in dm/device_compat.h
Signed-off-by: John Watts <contact@jookia.org>
|
|
This created a conflict when linking.
Signed-off-by: John Watts <contact@jookia.org>
|
|
These dependencies are required for building the drivers and create
compile errors if not enabled.
Signed-off-by: John Watts <contact@jookia.org>
[trini: Add ARCH_MVEBU to KIRKWOOD_SPI]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com> says:
This series adds support for Xilinx qspi parallel and
stacked memeories.
In parallel mode, the current implementation assumes that a maximum
of two flashes are connected. The QSPI controller splits the data
evenly between both the flashes so, both the flashes that are connected
in parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can differ
in sizes. So, except the sizes all other flash parameters of both the flashes
are identical.
Spi-nor will pass on the appropriate flash select flag to low level driver,
and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling the
address space each operation is performed at addr/2 flash offset, where addr
is the address specified by the user.
Similarly for read and erase operations it will read from both flashes, so
size and offset are divided by 2 and send to flash.
|
|
Enable the SPI_ADVANCE config option for all xilinx platforms, as
this is required for parallel-memories.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
|
|
Add support for parallel memories in zynq_qspi.c driver. In case of
parallel memories STRIPE bit is set and sent to the qspi ip, which will
send data bits to both the flashes in parallel. However for few commands
we should not use stripe, instead send same data to both the flashes.
Those commands are exclueded by using zynqmp_qspi_update_stripe().
Also update copyright info for this file.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
|
|
Add support for parallel memories in zynqmp_gqspi.c driver. In case of
parallel memories STRIPE bit is set and sent to the qspi ip, which will
send data bits to both the flashes in parallel. However for few commands
we should not use stripe, instead send same data to both the flashes.
Those commands are exclueded by using zynqmp_qspi_update_stripe().
Also update copyright info for this file.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
|
|
Read chipselect properties from DT which are populated using 'reg'
property and save it in plat->cs[] array for later use.
Also read multi chipselect capability which is used for
parallel-memories and return errors if they are passed on using DT but
driver is not capable of handling it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
|
|
write_bar
Add support for parallel memories and stacked memories configuration
in read_bar and write_bar functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
|
|
Add support for parallel memories flash configuration in read status
register and read flag status register functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
|
|
In parallel mode, the current implementation assumes that a maximum of
two flashes are connected. The QSPI controller splits the data evenly
between both the flashes so, both the flashes that are connected in
parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can
differ in sizes. So, except the sizes all other flash parameters of both
the flashes are identical
Spi-nor will pass on the appropriate flash select flag to low level
driver, and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling
the address space each operation is performed at addr/2 flash offset,
where addr is the address specified by the user.
Similarly for read and erase operations it will read from both flashes,
so size and offset are divided by 2 and send to flash.
Adding the config option SPI_ADVANCE for non SPL code.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
|
|
By default flash lock option is enabled, enable this option only
when it is required. By disabling the lock config will save some
amount of memory.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
|
|
During DT sync with kernel 6.6, AVS feature was removed by mistake.
So adding back AVS feature.
Fixes: df73e791ce09("arm: dts: j7200: dts sync with Linux 6.6-rc1")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
There are lots of usecases for running baremetal ELF
binaries via bootelf but if you enable bootelf you
get bootvx as well and you probably don't want or need
it.
Hide bootvx behind it's own configuration option.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
|
|
Add the "required", "algo", and "key-name-hint" nodes to the
signature/key node if ecdsa256 is used.
This change is mainly copy&paste from rsa_add_verify_data which already
adds these nodes.
Signed-off-by: Matthias Pritschet <matthias.pritschet@itk-engineering.de>
|
|
If the signature/key node(s) are not yet present in the U-Boot device
tree, ecdsa_add_verify_data simply fails if it can't find the nodes.
This behaviour differs from rsa_add_verify_data, wich does add the missing
nodes and proceeds in that case.
This change is mainly copy&paste from rsa_add_verify_data to add the
same behaviour to ecdsa_add_verify_data.
Signed-off-by: Matthias Pritschet <matthias.pritschet@itk-engineering.de>
|
|
There is no need to define a default for bootcmd in R5 u-boot because
the R5 is directly booting into the next stage A53 bootloader.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Initializing a clock driver to read a known static clock rate can take
some time at U-Boot proper pre-reloc phase.
Change to first try and read clock rate from DT to speed up boot time,
fall back to getting the clock rate from clock driver.
This help reduce boot time by around:
- ~35ms on a Radxa ROCK Pi 4 (RK3399)
- ~15ms on a Radxa ZERO 3W (RK3566)
Time that is wasted getting a static rate known at compile time.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Mediatek pinctrl drivers call mtk_gpiochip_register() to bind the child
gpio controller as part of mtk_pinctrl_common_probe(). This breaks
gpiohog support because the gpio controller is bound too late for
DM_FLAG_PROBE_AFTER_BIND (set while binding hogs) to work.
Move the mtk_gpiochip_register() to mtk_pinctrl_common_bind() and call
this as the .bind method of each of the mediatek pinctrl drivers.
Signed-off-by: Chris Webb <chris@arachsys.com>
|
|
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The SSCG is active with MDSEL[12] is not set. Previous commit
99c7e031196d ("clk: renesas: rcar-gen3: Replace SSCG caching
with MDSEL/PE caching") inverted the conditional assignment
of priv->sscg = !(cpg_mode & BIT(12)) during conversion from
(priv->sscg ? 16 : 0) to priv->cpg_mode & BIT(core->offset) ? 16 : 0;
Invert the assignment back to the correct state.
This fixes R8A77980, R8A77990, R8A77995 and R8A774C0.
Fixes: 99c7e031196d ("clk: renesas: rcar-gen3: Replace SSCG caching with MDSEL/PE caching")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-nand-flash into next
These are a number of assorted upstream Linux fixes to the
BRCMNAND driver.
This patch set lowers the hamming distance between the Linux
and U-Boot drivers a bit as well, while we deviate quite
a bit it is still possible to bring fixes over thanks to
exercises like this.
The patches pass the pipeline CI:
https://source.denx.de/u-boot/custodians/u-boot-nand-flash/-/pipelines/22535
|
|
Backport from the upstream Linux kernel
commit c2cf7e25eb2a3c915a420fb8ceed8912add7f36c
"mtd: rawnand: brcmnand: Add support for getting ecc setting from strap"
Note: the upstream kernel introduces a new
bool brcmnand_get_sector_size_1k() function because the int
version in U-Boot has been removed in Linux. I kept the old
int-returning version that is already in U-Boot as we depend
on that in other code.
BCMBCA broadband SoC based board design does not specify ecc setting in
dts but rather use the SoC NAND strap info to obtain the ecc strength
and spare area size setting. Add brcm,nand-ecc-use-strap dts propety for
this purpose and update driver to support this option. However these two
options can not be used at the same time.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240301173308.226004-1-william.zhang@broadcom.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Tested-by: William Zhang <william.zhang@broadcom.com>
|
