| Age | Commit message (Collapse) | Author |
|---|
|
Add initial support for SAMA7G54 Curiosity board.
Hardware:
SoC: SAMA7G54D2G SiP 1000 MHz
DRAM: DDR3 256 MiB
PMIC: MCP16502
Debug: UART3
Flash: QSPI NOR 8 MiB, SLC NAND 512 MiB
M.2 slot for wireless
Mikrobus connectors x 2
SD-Card connectors x 1
USB 2.0 x 3
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
|
|
Add initial device tree of the SAMA7G54 Curiosity board.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
|
|
Add flexcom 10 node for usage on the SAMA7G54 Curiosity board.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
|
|
Prepare v2024.04-rc4
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Use TF-A on imx8mp_beacon to fix boot regression.
- Use latest 6.8 dts for imx8mp_beacon.
- Fix the RAM initialization for phycore_imx8mp PCL-070 rev 1.
- Describe the 0087 i.mx8m mini product variant in tdx-cfg-block.
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The device tree has evolved over time, so re-sync. This also
partial reverts one change on the PCIe, because U-Boot doesn't
have a proper driver. However, since the clock is configured
to generate a 100MHz reference clock by default, a proper driver
isn't really necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
|
|
Add new product id 0087 Verdin iMX8M Mini Quad 2GB IT.
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
|
|
When the board was originally added, it enabled some features which
allowed it to bypass Trusted Firmware, but as the feature set of
Linux grew and more features became available, the U-Boot config
options which bypassed TF-A caused issues, so it needs to return
to the standard operating mode of using TF-A or the system no
longer boots.
Fixes: ab53bd43dbde ("arm64: imx: Add support for imx8mp-beacon-kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
We need to differ between PCL-070 and PCM-070. PCL-070 supports 2GHz RAM
timings from pcb rev 1 or newer. PCM-070 supports 2GHz RAM timings from
pcb rev 3 or newer.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
|
|
Add a function that gets the som_type from the EEPROM.
Add an enum for the som_type.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
|
|
- Singular quirk DT property rename.
|
|
In case the PHY is fully described in DT, use PHY MDIO address
from DT directly instead of always using auto-detection. This
also fixes the behavior of 'mdio list' in such DT setup, which
now prints the PHY connected to the MAC correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
- Add phytec am64x platform, update am65-cpsw and a few other assorted
fixes.
|
|
Drop old implementation and use hash_command() instead, as
how it's currently done for crc32 and sha1sum cmds.
Test:
=> md5sum 0x60000000 0x200
md5 for 60000000 ... 600001ff ==> e6bbbe95f5b41996f4a9b9af7bbd4050
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
|
|
Return value of a function 'malloc_cache_aligned'
is dereferenced at autoboot.c:207 without checking for NULL,
but it is usually checked for this function.
Found by RASU JSC.
Signed-off-by: Maks Mishin <maks.mishinFZ@gmail.com>
|
|
It is found that when DM is enabled, only generic init function is
called in .probe(). Baudrate is never honored. Add a function call
to .setbrg() when probing so that we can update the baudrate of the
serial device.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
|
|
Add a new Kconfig symbol MDIO_TI_CPSW for the CPSW MDIO
driver and build it with proper DM support if enabled.
If MDIO_TI_CPSW is not enabled then we continue to
behave like before.
Clean up MDIO custom handling in am65-cpsw and use
dm_eth_phy_connect() to get the PHY.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
|
|
Some platforms have bus level Reset controlled
by a GPIO line. If available then handle bus reset
via GPIO.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
|
|
Add documentation for PHYTEC phyCORE-AM64x SoM.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
Add support for PHYTEC phyCORE-AM64x SoM.
Supported features:
- 2GB DDR4 RAM
- eMMC Flash
- external uSD
- OSPI NOR Flash
- debug UART
Product page SoM: https://www.phytec.com/product/phycore-am64x
Device trees were taken from Linux v6.8-rc2.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
If mixed rsa and ecdsa keys are specified in dtsi, an rsa key can be sent
into the ecdsa verify. Without the ecdsa,curve property, this function will
crash due to lack of checking the null pointer return.
Signed-off-by: Bob Wolff <bob.wolff68@gmail.com>
|
|
Andrew Davis <afd@ti.com> says:
Explanation for this series is mostly in [4/6]. First 3
patches should be safe to take independent of the last 3.
|
|
The current address of TF-A in DRAM is just below the 512MB address line.
This means if the DRAM in a system is 512MB then TF-A is right at the
end of memory which is often reused, for instance U-Boot relocates itself
here. If a system has less than 512MB then that system wouldn't work at
all as TF-A would fail to load.
To avoid the issues above, move TF-A to the start of DRAM, which doesn't
change from system to system.
As TF-A is position independent, this has no dependency on TF-A. We
also fixup DT as needed when TF-A address is moved, so this change also
has no dependency on Linux and is fully forward/backward compatible.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
|
|
The address we load TFA and OP-TEE to is configurable by
CONFIG_K3_{ATF,OPTEE}_LOAD_ADDR, but the DT nodes reserving this memory
are static. Fix that by updating this node when the loaded address
does not match the address in DT.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
|
|
The address we load TF-A and OP-TEE to is configurable by Kconfig
CONFIG_K3_{ATF,OPTEE}_LOAD_ADDR, but the DT nodes reserving this memory
are often statically defined. As these binaries are dynamically loadable,
and in the case of OP-TEE may not even be loaded at all, hard-coding these
addresses is not a hardware description, but rather a configuration.
If the address that U-Boot loaded TF-A or OP-TEE does not match the
address in hard-coded in DT, then fix that node address. This also handles
the case when no reserved memory for these is provided by DT, which is
more correct as explained above.
Add this fixup function, and enable it for AM62.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
|
|
The fixups provided by ft_system_setup() are applicable for all AM62 based
boards. Select this at the target selection level for all AM62 boards and
remove it from any specific defconfig.
Signed-off-by: Andrew Davis <afd@ti.com>
|
|
Much like we have for ATF, OP-TEE has a standard address that we load
it too and run it from. Add a Kconfig item for this to remove some
hard-coding and allow this address to be more easily changed.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
|
|
There is a default ATF load address that is used for devices that have
ATF running in SRAM. For AM62 and AM62a, ATF runs from DRAM. Instead
of having to override the address in every defconfig, make add a
default for these ATF in DRAM devices.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
|
|
Allow boards that use ti_spl_template to not use optee part in
configuration.
Vendor can have module with 256 Mb of memory and they try to optimize
the available memory just using the essential components.
This change allow to remove tee from configuration without binman
fail.
configurations {
default = "conf-0";
conf-0 {
description = "k3-am62_ccm_m3";
firmware = "atf";
loadables = "dm", "spl";
fdt = "fdt-0";
};
};
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
Jonathan Humphreys <j-humphreys@ti.com> says:
This series enables OSPI storage and boot.
|
|
The phy calibration pattern partition isn't needed as the Cadence driver isn't
calibrating the phys.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Fixes: 58d61fb5a77e ("arm: dts: k3-j721e-sk: Add initial A72 specific dts support")
|
|
Add boot ROM XSPI bootmode, and set to BOOT_DEVICE_SPI if detected.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
|
|
Set config values to enable OSPI functionality.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
|
|
Jonathan Humphreys <j-humphreys@ti.com> says:
This series enables OSPI support for AM64x by setting the proper configs, and DT
entries for SPL.
|
|
Add bootph DT tags to enable OSPI in SPL.
Set OSPI regs for R5 SPL to address OSPI's boot region.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
Add configs to support OSPI flash.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
|
|
property as fallback (kernel 5.19+)
Clock names has been updated in kernel 5.19+ with the removal of
non-standard node names [1]. Due to this change, ft_opp_clock_fixups()
doesn't work anymore since ft_fixup_clocks() is looking to the clock
name and ft_opp_clock_fixups() error out with the following message:
ft_fixup_clocks failed for DSP voltage domain: <valid offset/length>
We can't use the new clock name since several clock are using the same
generic name "clock". ft_opp_clock_fixups() is looking at the clocks
node in cm_core_aon@0:
/sys/firmware/devicetree/base/ocp/interconnect@4a000000/segment@0/target-module@5000/cm_core_aon@0/clocks
...
clock@120
clock@160
clock@1a0
clock@1e0
clock@210
clock@234
clock@284
clock@2a8
clock@2d8
When fdt_subnode_offset() fail, we can look at clock-output-names
property as fallback since it contain the previous clock name.
libfdt doesn't provide any support to replace fdt_subnode_offset() by
a new function looking for clock-output-names property instead of the
node name. So we have to implement it in arch/arm/mach-omap2/omap5/fdt.c
for now.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=e4920169e7a2a839836d3a0d8cda1bae8caa3056
Cc: Suman Anna <s-anna@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Andrew Davis <afd@ti.com>
Signed-off-by: Romain Naour <romain.naour@skf.com>
|
|
The functions virtio_pci_get_config() and virtio_pci_set_config() don't
take the offset into account when reading the config space. For example
this manifests when U-Boot tries to read the MAC address of the VirtIO
networking device. It reads 6 equa bytes instead of the proper addess.
Fix those functions by taking the offset in the config space into
account.
Fixes: 4135e10732a0 ("virtio: Add virtio over pci transport driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Michał Barnaś <barnas@google.com> says:
Fix the driver to behave like the chip datasheet requires.
Improve wake up function to send low signal on SDA line for at least
60us as chip requires to wake up. Fix sleep function to move the chip
into sleep mode, not into idle mode. Remove unnecessary for loop,
which would never run for more than one iteration.
|
|
The ATSHA204A chip requires SDA line to go low for at least 60us to
wake up the chip. Previous implementation did not meet this requirement
due to the NAK received on bus and not sending the zeroes.
The function to ignore the NAK and send bytes regardless is not
supported in the u-boot making it impossible to wake up the chip
this way.
Instead, the bus speed, if needed, is set to lowest value and the
message is sent to the address 0x0. This way, the address of zero
makes the SDA line go low for about 80us, meeting the required time
to wake up the chip. The zero length packet is not sent by the i2c,
so the one byte is sent to the transfer function, but only the address
is sent anyway.
After sending the zero address, the bus speed is restored to the
previous value if it was slowed down to wake up the chip.
Signed-off-by: Michał Barnaś <barnas@google.com>
|
|
Fix the sleep function to issue the sleep command instead of idle one.
Signed-off-by: Michał Barnaś <barnas@google.com>
|
|
Some previous commit changed the continue statement to return,
making the for loop used to retry waking up the chip to always
return after one iteration. This commit removes the loop, cleaning
the code a little.
Signed-off-by: Michał Barnaś <barnas@google.com>
|
|
- net: mv88e6xxx: fix missing SMI address initialization (Marek)
- mvebu: turris_omnia: Enable networking via ethernet switch (Marek)
- mvebu: helios-4: add config fragment for spi booting et al (Josua)
- rng: Add Turris Mox rTWM RNG driver (Max)
|
|
One fix makes the reboot more robust on some older board, another one
stabilises the initial clock setup on the A10/A20.
Two patches make sure our DRAM init does not actually change the content
of the DRAM array, which allows to use DRAM for Linux' pstore
functionality.
We get SPI support for U-Boot proper for one more SoC, that patch was
lingering around for a while, and should not affect other SoCs, so I am
merging this now.
As an added bonus, we get the defconfig file for a new board, the DT was
already synced from the kernel tree.
The CI looked happy with changes, and I tested them on five different
boards with different SoCs.
|
|
A RNG driver for Armada 3720 boards running the Turris Mox rWTM firmware
from CZ.NIC in the secure processor.
Signed-off-by: Max Resch <resch.max@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add a config fragment with required differences for booting from spi
flash instead of sd-card (default).
Settings for environment location are based on vendor u-boot:
https://github.com/kobol-io/u-boot/blob/helios4/include/configs/helios4.h#L59
The fragment can be applied on top of helios4_defconfig by make:
make helios4_defconfig spiboot.config
Signed-off-by: Josua Mayer <josua@solid-run.com>
|
|
Update the helios4 defconfig to enable the 'setexpr' command, which is a
default and useful for various complex boot-scripts.
Signed-off-by: Josua Mayer <josua@solid-run.com>
|
|
SolidRun Armada-388 SoM has an i2c bus supporting on-som eeprom, and
peripherals on a carrier.
armada-38x.dtsi disables this bus by default, it should be enabled by
som or carrier dts.
Linux has moved i2c0 from helios-4 board dts to som dtsi, including
status, pinctrl and clock speed.
Copy these settings from mainline.
This fixes accessing i2c bus from u-boot commandline.
Signed-off-by: Josua Mayer <josua@solid-run.com>
|
