| Age | Commit message (Collapse) | Author |
|---|
|
In case of an OTP-CLOSED STM32MP15xx system, the CPU core 1 cannot be
released from endless loop in BootROM only by populating TAMP BKPxR 4
and 5 with magic and branch address and sending SGI0 interrupt from
core 0 to core 1 twice. TAMP_SMCR BKP..PROT fields must be initialized
as well to release the core 1 from endless loop during the second SGI0
handling on core 1. Initialize TAMP_SMCR to protect the first 32 backup
registers, the ones which contain the core 1 magic, branch address and
boot information.
This requirement seems to be undocumented, therefore it was necessary
to trace and analyze the STM32MP15xx BootROM using OpenOCD and objdump.
Ultimately, it turns out that a certain BootROM function reads out the
TAMP_SMCR register and tests whether the BKP..PROT fields are non-zero.
If they are zero, the BootROM code again waits for SGI0 using WFI, else
the execution moves forward until it reaches handoff to the TAMP BKPxR 5
branch address.
This fixes CPU core 1 release using U-Boot PSCI implementation on an
OTP-CLOSED system, i.e. system with fuse 0 bit 6 set.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
SoC revision is only accessible via DBUMCU IDC register,
which requires BSEC.DENABLE DBGSWENABLE bit to be set to
make the register accessible, otherwise an access to the
register triggers bus fault. As BSEC.DBGSWENABLE is zero
in case of an OTP-CLOSED system, do NOT set DBGSWENABLE
bit as this might open a brief window for timing attacks.
Instead, report that this system is OTP-CLOSED and do not
report any SoC revision to avoid confusing users. Use an
SEC/C abbreviation to avoid growing SOC_NAME_SIZE .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The source file is in arch/arm/mach-stm32mp/ecdsa_romapi.c and not
in arch/arm/mach-stm32mp/stm32mp1/ecdsa_romapi.c . There are two
Makefile entries in each subdirectory. Drop the bogus one and keep
only the correct one, the one in arch/arm/mach-stm32mp/Makefile .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
In case the system has resumed successfully, the PSCI suspend resume
code has to jump to the 'ep' successful resume entry point code path,
otherwise the code has to jump to content of the LR register, which
points to failed resume code path.
To implement this distinction, rewrite LR register stored on stack
with 'ep' value in case of a successful resume, which is really in
every case unless some catastrophic failure occurred during suspend.
Without this change, Linux counts every resume as failed in
/sys/power/suspend_stats/fail
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
|
|
Add a function setup_mac_address() to update the MAC address from the
default location in OTP for stm32mp2 platform.
The max number of OTP for MAC address is increased to 8 for STM32MP25,
defined with get_eth_nb() and checked in setup_mac_address.
The MAC address FF:FF:FF:FF:FF:FF, the broadcast ethaddr, is a invalid
value used for unused MAC address slot in OTP, for example for board
with STM32MP25x part number allows up to 5 ethernet ports but it is not
supported by the hardware, without switch; the associated variable
"enetaddr%d" is not created.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Add support of serial number for stm32mp25, gets from OTP with BSEC driver.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
|
|
Add a new file soc.c for common functions between stm32mp1 and stm32mp2
family and move print_cpuinfo() in this new file.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
|
|
Prepare v2024.01-rc3
|
|
Add initial support for STM32MP2 SoCs family.
SoCs information are available here :
https://www.st.com/content/st_com/en/campaigns/microprocessor-stm32mp2.html
Migrate all MP1 related code into stm32mp1/ directory
Create stm32mp2 directory dedicated for STM32MP2 SoCs.
Common code to MP1, MP13 and MP25 is kept into
arch/arm/mach-stm32/mach-stm32mp directory :
- boot_params.c
- bsec
- cmd_stm32key
- cmd_stm32prog
- dram_init.c
- syscon.c
- ecdsa_romapi.c
For STM32MP2, it also :
- adds memory region description needed for ARMv8 MMU.
- enables early data cache before relocation.
During the transition before/after relocation, the MMU, initially setup
at the beginning of DDR, must be setup again at a correct address after
relocation. This is done in enables_caches() by disabling cache, force
arch.tlb_fillptr to NULL which will force the MMU to be setup again but
with a new value for gd->arch.tlb_addr. gd->arch.tlb_addr has been
updated after relocation in arm_reserve_mmu().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
