summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2022-09-16blk: Enable CONFIG_BLK for all mediaSimon Glass
Enable this option on all boards which support block devices. Drop the related depencies on BLK since these are not needed anymore. Disable BLOCK_CACHE on M5253DEMO as this causes a build error. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-09-15brppt1: Cleanup device treeBernhard Messerklinger
* Remove unnecessary device tree nodes which are not needed in U-Boot directly. * Move all U-Boot specific device tree properties to u-boot dtsi. Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
2022-09-15brppt1: Fix SPL boot stageBernhard Messerklinger
Commit 6337d53fdf45 ("arm: dts: sync am33xx with Linux 5.9-rc7") syncs the am335x device tree with the latest linux kernel am335x device tree. That causes problems with device tree in SPL stage. To fix the issues CONFIG_SPL_OF_TRANSLATE must be set to handle the synced bus addresses correctly. A custom U-Boot device tree is also needed since the SPL build removes bus properties from bus nodes which are not explicitly marked with the u-boot,dm-spl or u-boot,dm-pre-reloc flag. Therefore all parent buses of the in the SPL needed devices must be marked with u-boot,dm-pre-reloc. Also since there is no driver for "ti,sysc" compatible property in SPL the buses marked with this compatible string must also be marked with compatible = "simple-bus" to make the underlying devices visible in SPL. Otherwise the matching device drivers aren't found and the uclass drivers are dropped. Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
2022-09-15brppt1: Remove unused board variantsBernhard Messerklinger
The SPI and NAND board variants never went into production. Drop those board variants. Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
2022-09-14Add in the ability to load and boot an uncompressed kernel image during the ↵Nathan Barrett-Morrison
Falcon Mode boot sequence. This is required for architectures which do not support compressed kernel images (i.e. ARM64). This is only used while not booting via FIT image. Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2022-09-13arm: dts: aspeed: Update SPI flash node settingsChin-Ting Kuo
For both AST2500 and AST2600, there are three SPI controllers, FMC(Firmware Memory Controller), SPI1 and SPI2. The clock source is HCLK. Following is the basic information for ASPEED SPI controller. AST2500: - FMC: CS number: 3 controller reg: 0x1e620000 - 0x1e62ffff decoded address: 0x20000000 - 0x2fffffff - SPI1: CS number: 2 controller reg: 0x1e630000 - 0x1e630fff decoded address: 0x30000000 - 0x37ffffff - SPI2: CS number: 2 controller reg: 0x1e631000 - 0x1e631fff decoded address: 0x38000000 - 0x3fffffff AST2600: - FMC: CS number: 3 controller reg: 0x1e620000 - 0x1e62ffff decoded address: 0x20000000 - 0x2fffffff - SPI1: CS number: 2 controller reg: 0x1e630000 - 0x1e630fff decoded address: 0x30000000 - 0x3fffffff - SPI2: CS number: 3 controller reg: 0x1e631000 - 0x1e631fff decoded address: 0x50000000 - 0x5fffffff Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
2022-09-13xilinx: Fix mdio bus description for vck190-scMichal Simek
Current behavior is that eth_phy_get_mdio_bus Net: FEC: can't find phy-handle ZYNQ GEM: ff0b0000, mdio bus ff0b0000, phyaddr 0, interface sgmii eth0: ethernet@ff0b0000 Net: ZYNQ GEM: ff0b0000, mdio bus ff0b0000, phyaddr 0, interface sgmii eth0: ethernet@ff0b0000 Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/5b7da5808136b3f579c0cf7a3431b56c758655e9.1662460749.git.michal.simek@amd.com
2022-09-13ARM: zynq: DT: List OCM memoryMichal Simek
Description OCM with mmio-sram driver. In 99% use cases OCM is mapped high that's why it is placed on fixed location. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/a951dbe885640197efe3e91bb9fa5caedb54b387.1662460712.git.michal.simek@amd.com
2022-09-13ARM: zynq: Align qspi node name with Linux kernelMichal Simek
Nodes should follow generic rules where compatible and reg properties should be listed on the top of node. That's why sync it up. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/922dca6227cb0aa4f79e6d3595c5f280ba020684.1662460540.git.michal.simek@amd.com
2022-09-13arm64: versal: Define zynqmp_mmio_write() for versalMichal Simek
GQSPI driver is using it but this function is never called for Versal because it is removed by linker. But function should be declared to avoid this build warning: drivers/spi/zynqmp_gqspi.c: In function 'zynqmp_qspi_set_tapdelay': drivers/spi/zynqmp_gqspi.c:378:3: warning: implicit declaration of function 'zynqmp_mmio_write' [-Wimplicit-function-declaration] 378 | zynqmp_mmio_write(IOU_TAPDLY_BYPASS_OFST, Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com> Link: https://lore.kernel.org/r/20220825125906.11581-3-ashok.reddy.soma@amd.com Signed-off-by: Michal Simek <michal.simek@amd.com>
2022-09-13ARM: zynq: Align bss and end of u-boot image to 64bitsMichal Simek
The main reason is that DT memory reserved code is expecting DT to be 64bit aligned. For more information take a look at commit 5bd5ee02b23b ("xilinx: zynqmp: Check that DT is 64bit aligned"). Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/9f3688cda188d8ea0b462df2aa08a10ddcc9c149.1661938136.git.michal.simek@amd.com
2022-09-13arm64: zynqmp: add ref_clk property for REFCLKPER calculationPiyush Mehta
Added ref_clk 'ref' property for GUCTL_REFCLKPER and GFLADJ_REFCLK_FLADJ calculation. This property configure correct value for SOF/ITP counter and period of ref_clk. This patch adds 'ref' property for both dwc3_0 and dwc3_1 cores. Signed-off-by: Piyush Mehta <piyush.mehta@amd.com> Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/417545b948ea12a9301a5e80851f98523be2b443.1661259809.git.michal.simek@amd.com
2022-09-13arm64: zynqmp: Add missing tca6416 to zynqmp SCMichal Simek
Add missing tca6416 i2c gpio controller to SC dts file. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/a19c191d0dffb213d9dc8809d22728d79cf73a22.1661259623.git.michal.simek@amd.com
2022-09-13arm: dts: Add xlnx prefix to GEM compatible stringHarini Katakam
cdns,zynq/zynqmp were recentle deprecated in Linux in favour of xlnx prefix. Add this new compatible string and retain the existing string for compatibility with uboot drivers. Signed-off-by: Harini Katakam <harini.katakam@amd.com> Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/a38b1b55132fc026cc09224dba61e42fd03b1a36.1661259558.git.michal.simek@amd.com
2022-09-13arm64: zynqmp: Add mtd partition for secure OS storage areaAmit Kumar Mahapatra
Update MTD partitions of Kria device trees to allocate 128KB of QSPI memory for secure OS. Increased "SHA256" partition size & changed starting address of "User" partition to accommodate the new partition "Secure OS Storage" Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/9cc64b8c731d11439de73d0af54c65080068f00b.1661242681.git.michal.simek@amd.com
2022-09-12zynq: Convert arm twd timer to DM driverStefan Herbrechtsmeier
Move arm twd timer driver from zynq to generic location. DM timer drivers are designed differently to original driver. Timer is counting up and not down. Information about clock rates are find out in timer_pre_probe() that's why there is no need to get any additional information from DT in the driver itself (only register offset). Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com> Link: https://lore.kernel.org/r/20220805061629.1207-1-stefan.herbrechtsmeier-oss@weidmueller.com Signed-off-by: Michal Simek <michal.simek@amd.com>
2022-09-02Makefile: Allow LTO to be disabled for a buildSimon Glass
LTO (Link-Time Optimisation) is an very useful feature which can significantly reduce the size of U-Boot binaries. So far it has been made available for selected ARM boards and sandbox. However, incremental builds are much slower when LTO is used. For example, an incremental build of sandbox takes 2.1 seconds on my machine, but 6.7 seconds with LTO enabled. Add a NO_LTO parameter to the build, similar to NO_SDL, so it can be disabled during development if needed, for faster builds. Add some documentation about LTO while we are here. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-09-02arm: ARMv4 assembly compatibilitySergei Antonov
There is currently a problem that U-Boot can not work on ARMv4 because assembly imlementations of memcpy() and some other functions use "bx lr" instruction that is not available on ARMv4 ("mov pc, lr" should be used instead). A working preprocessor-based solution to this problem is found in arch/arm/lib/relocate.S. Move it to the "ret" macro in arch/arm/include/asm/assembler.h and change all "bx lr" code to "ret lr" in functions that may run on ARMv4. Linux source code deals with this problem in the same manner. v1 -> v2: Comment update. Pointed out by Andre Przywara. Signed-off-by: Sergei Antonov <saproj@gmail.com> CC: Samuel Holland <samuel@sholland.org> CC: Ye Li <ye.li@nxp.com> CC: Simon Glass <sjg@chromium.org> CC: Andre Przywara <andre.przywara@arm.com> CC: Marek Vasut <marex@denx.de> CC: Sean Anderson <sean.anderson@seco.com> CC: Tom Rini <trini@konsulko.com>
2022-09-01ARM: cache: Allow SPL to build cache-pl310.cPhilip Oberfichtner
Introduce the new Kconfig symbol CONFIG_SPL_SYS_L2_PL310 to allow the SPL to build cache-pl310.c. Before this commit, the SPL could enable the PL310 L2 cache [1], but the cache maintenance functions from cache-pl310.c were only useable for non-SPL builds. After enabling the cache one must be able to flush it, too. Thus this commit allows cache-pl310.c to be included in the SPL build. [1] See for example arch/arm/mach-imx/cache.c: v7_outer_cache_enable() Signed-off-by: Philip Oberfichtner <pro@denx.de>
2022-09-01Convert CONFIG_SYS_L2_PL310 to KconfigPhilip Oberfichtner
This converts CONFIG_SYS_L2_PL310 to Kconfig. For omap2 and mvebu the 'select SYS_L2_PL310' locations were determined using ./tools/moveconfig -i CONFIG_SYS_L2_PL310. For mx6 I manually chose ARCH_MX6 as 'select' location. The correctness has been verified using $ ./tools/moveconfig.py -f ARCH_MX6 ~SYS_L2_PL310 ~SYS_L2CACHE_OFF 0 matches That means whenever an ARCH_MX6 board had SYS_L2_PL310 disabled, this was correctly reflected in SYS_L2CACHE_OFF. Thus it's safe to insert the 'select' statement under ARCH_MX6. Signed-off-by: Philip Oberfichtner <pro@denx.de>
2022-08-26arm: dts: qcom: Sync pinctrl DT nodes with Linux bindingsSumit Garg
Currently for all Qcom SoCs/boards there are separate compatibles for GPIO and pinctrl. But this is inconsistent with official (upstream) Linux bindings which requires only a single compatible "qcom,<SoC name>-pinctrl" and there is no such compatible property as "qcom,tlmm-<SoC name>". So fix this inconsistency for Qcom SoCs in order to comply with upstream DT bindings. This is done via removing compatibles from "msm_gpio" driver and via binding to "msm_gpio" driver from pinctrl driver in case "gpio-controller" property is specified for pinctrl node. Suggested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2022-08-26pinctrl: sdm845: Remove redundant CONFIG_SDM845 checkSumit Garg
DT compatible is sufficient to make platform specific differentiation, so remove redundant CONFIG_SDM845 check. Signed-off-by: Sumit Garg <sumit.garg@linaro.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-08-26board: qcs404-evb: Enable USB3 specific PMIC GPIOSumit Garg
For USB3 host controller to detect devices on the bus it is required to enable a PMIC GPIO: usb_vbus_boost_pin. So enable that during board specific initialization. And since this PMIC GPIO parsing is quite u-boot specific, so add a DT override to qcs404-evb-uboot.dtsi to represent usb_vbus_boost_pin. Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2022-08-26dts: qcs404-evb: Add PMIC GPIO controller nodeSumit Garg
PMIC GPIOs are special GPIOs which are accessible through SPMI bus. So add corresponding DT nodes. Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2022-08-26dts: qcs404-evb: Add USB controller and PHY nodesSumit Garg
QCS404 SoC provides support for two USB controllers: one USB3 and the other one being USB2. The USB3 controller supports further 2 PHY: one high speed PHY and the other super speed PHY. The USB2 controller supports a single high speed PHY. So add corresponding DT nodes. Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2022-08-26clocks: qcs404: Add support for USB clocksSumit Garg
Add support for USB controller and PHY clocks for QCS404 SoC. Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2022-08-26clocks: qcom: Add clock enable callback supportSumit Garg
Drivers like USB, ethernet etc. uses ".enable" hook to enable clocks. So add corresponding support for Qcom clock drivers. Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2022-08-26dts: qcs404-evb: Add reset controller nodeSumit Garg
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
2022-08-26arm: total_compute: enable psciDavidson K
psci is used for system reset Signed-off-by: Davidson K <davidson.kumaresan@arm.com>
2022-08-23board: lsxl: disable eth0Michael Walle
The board has only one network interface. The linux kernel will gracefully skip a the ethernet interface if no connected PHY could be probed. u-boot on the other hand will throw an error message. The kernel device tree is about to be fixed. For now, just disable the ethernet interface in our -u-boot.dtsi. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Stefan Roese <sr@denx.de>
2022-08-23board: lsxl: convert to DM_GPIOMichael Walle
Use the new mvebu GPIO driver and convert all the function calls to the former kirkwood GPIO driver. This means that we are now using the LED uclass and the regulator uclass. Unfortunately, the GPIO LED doesn't offer a blinking method. Thus we are now stuck with solid on and off states, which makes debugging a bit harder. Also, there is no GPIO fan driver for now. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Stefan Roese <sr@denx.de>
2022-08-23board: lsxl: make last resort recovery more reliableMichael Walle
If something is wrong with the environment, we cannot rely on a proper u-boot operation anymore. In fact, it is possible, that we never reach misc_init_r() with a broken environment. Also don't enable the netconsole by environment settings. This way the user don't have to reconfigure the environment. Instead the network console is only enabled when the push button is pressed during boot. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Stefan Roese <sr@denx.de>
2022-08-23board: lsxl: automatically select CONFIG_MISC_INIT_RMichael Walle
The board code needs this to be set. Otherwise, the recovery mechanism doesn't work. Therefore, select this option automatically with the board. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Stefan Roese <sr@denx.de>
2022-08-23arm: kirkwood: make it CONFIG_TIMER awareMichael Walle
If we switch to CONFIG_TIMER, we don't need the legacy timer macros and functions anymore. Add the proper guards to exclude them from compiling. Cc: Pali Rohár <pali@kernel.org> Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-08-23arm: kirkwood: 88f6281: Detect CONFIG_SYS_TCLK from SAR registerPali Rohár
Bit 21 in SAR register specifies if TCLK is running at 166 MHz or 200 MHz. This information is undocumented in public Marvell Kirkwood Functional Specifications [2], but is available in Linux v3.15 kirkwood code [1]. Commit 8ac303d49f89 ("arm: kirkwood: Do not overwrite CONFIG_SYS_TCLK") broke support for Marvell 88F6281 SoCs because it was expected that all those SoCs have TCLK running at 200 MHz as specified in Marvell 88F6281 Hardware Specifications [3]. Fix broken support for 88F6281 by detecting CONFIG_SYS_TCLK from SAR register, like it was doing Linux v3.15. [1] - https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/arch/arm/mach-kirkwood/common.c?h=v3.15#n542 [2] - https://web.archive.org/web/20130730091033/http://www.marvell.com/embedded-processors/kirkwood/assets/FS_88F6180_9x_6281_OpenSource.pdf [3] - https://web.archive.org/web/20120620073511/http://www.marvell.com/embedded-processors/kirkwood/assets/HW_88F6281_OpenSource.pdf Update by Stefan 2022-08-23: - Fix compilation error for ds109 Fixes: 8ac303d49f89 ("arm: kirkwood: Do not overwrite CONFIG_SYS_TCLK") Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-08-23arm: mvebu: mbus: Fix mbus driver to work also after U-Boot relocationPali Rohár
mbus driver is initialized from arch_cpu_init() callback which is called before relocation. This driver stores lot of functions and structure pointers into global variables, so it is data position dependent. Therefore after relocations all pointers are invalid and driver does not work anymore as all pointers referes to the old memory, which overlaps with CONFIG_SYS_LOAD_ADDR and ${loadaddr}. For example U-Boot fuse command crashes if loadaddr memory is cleared or rewritten by some image loaded by U-Boot load command. mw.w ${loadaddr} 0x0 10000 fuse read 0 1 2 Fix this issue by removing of all mbus global variables in which are stored pointers to structures or functions which changes during relocation. And replace it by direct function calls (not via pointers). With this change fuse command finally works. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Stefan Roese <sr@denx.de>
2022-08-23arm: mvebu: Define env_sf_get_env_addr() for all Armada boards in SPLPali Rohár
SPI0 CS0 Flash is mapped to address range 0xD4000000 - 0xD7FFFFFF by BootROM. Proper U-Boot removes this direct mapping. So it is available only in SPL. This applies for all 32-bit Armada BootROMs. SPL mvebu code is used only on 32-bit Armada SoCs. So move env_sf_get_env_addr() function from Turris Omnia board to common SPL mvebu code and add proper checks for SPI0 CS0. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-08-20arm: Remove warp boardTom Rini
This board is missing migration to CONFIG_DM, which had a deadline of v2020.01, which is now more than 2 years passed due. Remove it. Cc: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-20layerscape: Disable CONFIG_FMAN_ENET on *aqds* platformsTom Rini
The *aqds* platforms have not been migrated to be able to enable CONFIG_DM_ETH with CONFIG_FMAN_ENET. Disable CONFIG_FMAN_ENET on these platforms. Cc: Mingkai Hu <mingkai.hu@nxp.com> Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com> Cc: Pramod Kumar <pramod.kumar_1@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-20net: lpc32xx_eth.c ethernet driverTom Rini
This driver has not been converted to DM_ETH. The migration deadline passed 2 years ago. Cc: Trevor Woerner <twoerner@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Ramon Fried <rfried.dev@gmail.com>
2022-08-20arm: Remove kzm9g boardTom Rini
This board is behind on several mandatory DM migrations and is missing OF_CONTROL support that makes other conversions impossible. Remove it. Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-20arm: Remove armadillo-800eva boardTom Rini
This board is behind on several mandatory DM migrations and is missing OF_CONTROL support that makes other conversions impossible. Remove it. Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-20arm: Remove cm_t335 boardTom Rini
This board is behind on several mandatory DM migrations and is missing OF_CONTROL support that makes other conversions impossible. Remove it. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Uri Mashiach <uri.mashiach@compulab.co.il> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-20arm: Remove edminiv2 boardTom Rini
This board is not converted to use CONFIG_DM, well passed the migration deadline. Remove it. Cc: Simon Guinot <simon.guinot@sequanux.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-08-20arm64: explicitly disable pointer authentication instructionsRasmus Villemoes
The Yocto project builds their aarch64 cross-compiler with the configure knob --enable-standard-branch-protection, which means that their gcc behaves as if -mbranch-protection=standard is passed; the default (lacking that configure knob) is -mbranch-protection=none. This means that when building U-Boot using the Yocto toolchain, most functions end up containing paciasp/autiasp/bti instructions. However, since U-Boot is not an ordinary userspace application, there's no OS kernel which has set up the required authentication keys, so these instructions do nothing at all (even on arm64 hardware that does have the pointer authentication capability). They do however make the image larger. It is theoretically possible for U-Boot to make use of the pointer authentication protection - cf. the linux kernel's CONFIG_ARM64_PTR_AUTH_KERNEL - but it is far from trivial, and it's hard to see just what threat model it would protect against in a bootloader context. Regardless, we certainly have none of the required infrastructure now, so explicitly pass -mbranch-protection=none to ensure those useless instructions do not get emitted. For a toolchain not configured with --enable-standard-branch-protection, this changes nothing. For the Yocto toolchain, this reduces the size of both SPL and U-Boot proper by about 3% for my imx8mp target. If you don't have a Yocto toolchain, the effect can easily be reproduced by applying this patch and changing =none to =standard. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-08-20Restore pcm051_rev3_defconfig configMatwey V. Kornilov
pcm051_rev3_defconfig config (Phytec Wega board) has been dropped in 64efd11d ("arm: Remove pcm051 board") due to expired migration deadlines. Here, pcm051_rev3_defconfig support is reintroduced. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2022-08-20Nokia RX-51: Move board required options from defconfig to KconfigPali Rohár
Some of config options are board specific and should be set in into their default values automatically. So move them from defconfig file to Kconfig definitions to ensure that possible user custom defconfig files would have these required options also enabled. Signed-off-by: Pali Rohár <pali@kernel.org>
2022-08-20Nokia RX-51: Use U-Boot generic position independent codePali Rohár
Switch from custom board specific fixup/copy code to U-Boot generic position independent code provided by config option POSITION_INDEPENDENT. This also slightly decrease size of u-boot.bin binary (by 52 bytes). Note that option POSITION_INDEPENDENT increase size but not more than custom board fixup/copy code which is being deleted (as it is not needed anymore). Signed-off-by: Pali Rohár <pali@kernel.org>
2022-08-20arm: Set default MACH_TYPE in KconfigPali Rohár
For boards which requires correct MACH_TYPE, set their correct default values directly in Kconfig. Signed-off-by: Pali Rohár <pali@kernel.org>
2022-08-16ls1021atwr: caam: Enable Uboot validaion in SPL.Gaurav Jain
caam driver model enabled in spl for secure boot. fsl_rsa_mod_exp driver enabled in spl for validating uboot image. Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
generated by cgit v1.2.3 (git 2.0.4) at 2025-08-06 20:09:55 +0000