| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Andrew Davis <afd@ti.com>
|
|
I updated the mailmap a while back but it's nice to have authorship
comments adjusted too.
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
|
|
Add the basic Kconfig options, addresses and other values for the
existing Kconfig settings for the new Allwinner A523/T527/H728 SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Add reverse engineered code to add support for DDR3 DRAM chips on the
Allwinner A523 DRAM controller.
The timings are copying what boot0 set up on the X96QPro+ TV box, though
they seem quite suboptimal, with longer latencies that would be required
for DDR3-1600. The chips are also actually capable of DDR3-1833, so
there is room for future improvement.
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
[Andre: rework to copy from H616 DDR3 driver, calculate timings]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
DRAM init code, as per reverse engineering and matching against
previous SoCs. As usual no real documentation, and the DRAM controller
is the usual mixture of close-to-previous IP and new inventions.
This version supports LPDDR4 for now only, as seen on the early boards.
This needs improvements, but it can be done later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
This adds the early A523 clock setup code, for the basic peripheral PLL
and the basic bus clocks (APB/AHB). This is quite close to the existing
H6 and H616 clock code, so this shares the same file. A few bits and bobs
are different, though, so filter for the A523 in a few occasions.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
The cpu_sunxi_ncat2.h header file contains addresses of some peripherals
that are needed for the SPL, for chips that belong to the "NCAT2"
generation.
The Allwinner A523 is a member of this group, but a few addresses
differ, and we need a few more addresses, for playing with the core
reset, for instance.
Add the new addresses needed for the A523 and guard existing definitions
that conflict with that new chip.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
The watchdog in the Allwinner A523 SoC differs a bit from the one in the
previous SoCs: it lives in a separate register frame, so no longer
inside some timer device, and it manages to shuffle around some
registers a bit. But it also conveniently adds a direct reset
functionality, so we don't need to use a dummy timeout period.
Avoid introducing a new MMIO register frame C struct, but just define
the one needed register offset as a macro. Then just trigger this new
direct reset functionality in the A523 specific reset_cpu()
implementation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
The Allwinner A523 features 8 CPU cores, organised in two clusters, both
driven by separate PLLs. Also there is the DSU PLL, which clocks the
hardware that connects the cores to the rest of the system.
And while the PLL registers itself are very similar, they are located in
a separate register frame, outside the main CCU, and also the register
controlling the CPU clock source (mux) is different.
Provide a separate function that reparents the two clusters and the DSU,
while their PLLs are programmed. For the actual PLL programming, we rely
on the existing shared routine.
The selection between the new A523 routine and the existing code is made
with C if statements, but since the choice is effectively made at compile
time already, the compiler optimises away the other code paths, leaving
just the one required function in.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
When we program the CPU PLL, we need to switch the CPU clock source away
from the PLL temporarily, then switch it back, once the PLL has
stabilised.
The CPU CLK register will be different on the A523, so move the current
code into a separate function, to allow using a different version of
that later for the A523.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
The SPL initial clock setup code for the Allwinner H6 and H616 SoCs uses
a simple CPU PLL setup routine, which programs all register bits at once,
then waits for the LOCK bit to clear.
The manual suggests to follow a certain procedure for bringing up any
PLLs, which involves several register writes, one at a time, and some
delays. Also the H616 and the new A523 require some tiny changes in this
sequence, and the different SoCs also feature some extra bits here and
there, which we should not just clear.
So factor out the PLL setup routine, and make it follow the manual's
suggestion. This will read the PLL register at the beginning, then tweak
the bits we need to manipulate, and writes the register several times on
the way. This allows to cover the specific bits for different SoCs.
Besides improving the reliability of the PLL setup, this helps with the
A523, which requires *three* CPU PLLs to be programmed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
The Allwinner PLLs share most of their control bits, they differ mostly
in the factors and dividers.
Drop the PLL specific definition of those common bits, and use one
shared macro, for all PLLs.
This requires changing the users in the SPL clock and DRAM code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
The generic name 'EFI' would be more useful for common EFI features. At
present it just refers to the EFI app and stub, which is confusing.
Rename it to EFI_CLIENT
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27149
- Add support for the NXP imx93 frdm board.
- imx93_evk and phycore-imx93 cleanups.
- Convert imx6dl-sielaff to OF_UPSTREAM and fix serial download mode boot.
- Fix crash in imx power-domain.
- Migrate Phytec imx8mm boards to standard boot.
- Fix smatch warnings.
|
|
Neha Malcom Francis <n-francis@ti.com> says:
This series implements a driver for the BIST (Built-In Self Test) module
for K3 devices. The BIST driver must ideally support triggering of BIST
tests, both PBIST (Memory BIST) and LBIST (Logic BIST) on a core. Both
tests are destructive in nature. Please see links [1] and [2] for
further information regarding the two.
At boot up, BIST is executed by hardware for the MCU domain
automatically as part of HW POST. So BIST has been checked only for the
MCU domain when U-Boot comes up in the usual U-Boot to Linux boot flow.
To facilitate the use-case where some safe firmware is intended to be
run on a safe core, it is best to have triggered the BIST tests on that
core. As an example, we take triggering the BIST tests on the MAIN R52_x
cores. The triggering patch is kept as DONOTMERGE.
The general procedure for triggering BIST on a core is:
1. Power on the core under test following a sequence
2. Trigger the BIST test
3. Reset the core under test following a sequence
BIST tests are triggered from A72 SPL where the DM (Device Manager
firmware that handles power management) is already up and can perform
these power sequences for us.
Boot logs (with LOG_DEBUG and CONFIG_K3_BIST enabled) and DT node kept (already
merged to ti-k3-dts-next [3]):
https://gist.github.com/nehamalcom/3fed504d038b54e3e05ba3874d73d603
[1] https://software-dl.ti.com/jacinto7/esd/processor-sdk-rtos-jacinto7/latest/exports/docs/sdl/sdl_docs/userguide/j721e/modules/pbist.html#introduction
[2] https://software-dl.ti.com/jacinto7/esd/processor-sdk-rtos-jacinto7/latest/exports/docs/sdl/sdl_docs/userguide/j721e/modules/lbist.html#introduction
[3] https://lore.kernel.org/all/175205725858.918402.3771835070085533874.b4-ty@ti.com/
Link: https://lore.kernel.org/r/20250716062156.2564297-1-n-francis@ti.com
|
|
The load address for the R5's SPL is defined in Kconfig by
SPL_TEXT_BASE. Rather than hard coding the load address which could
lead to hard to debug issues if this value is changed, just use the
SPL_TEXT_BASE value.
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
|
|
The uart11 reg address was a copy of the value for uart10.
Update it to the correct value.
Signed-off-by: Rebecca Cran <rebecca@os.amperecomputing.com>
|
|
Trigger all tests of PBIST and LBIST using appropriate calls to set the
core under test (MAIN R5 2_0) to it's required state.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
|
|
Add the initial board support for the NXP i.MX93 FRDM board:
https://www.nxp.com/design/design-center/development-boards-and-designs/frdm-i-mx-93-development-board:FRDM-IMX93
Based on the NXP U-Boot code.
There were attempts to upstream the board devicetree, but it has not been
accepted upstream yet:
https://lore.kernel.org/linux-arm-kernel/20250526-fpg-nxp-imx93-frdm-v2-2-e5ad0efaec33@pengutronix.de/
Once it reaches upstream, we can switch to OF_UPSTREAM.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Switch to OF_UPSTREAM to make use of the upstream devicetree.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
There is a value to generate fit-dtb.blob even for cases without SPL
because flows with FSBL also require it.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c2952da3c064d67821cd166d2392db39c1d23b2c.1752822270.git.michal.simek@amd.com
|
|
Aristo Chen <jj251510319013@gmail.com> says:
This patch series introduces a validation step in `mkimage` to ensure that
the `default` property under the `/configurations` node in a FIT image
references a valid subnode. If the referenced node does not exist, mkimage
now prints an error and fails early. This helps prevent runtime failures
when U-Boot attempts to boot using an undefined configuration.
The first patch implements the validation logic in `fit_image.c`. The second
patch fixes an invalid default configuration reference exposed by this new
check in the `k3-am65-iot2050-boot-image.dtsi`. The final patch adds a test
case to verify that mkimage correctly fails when an invalid default
configuration is present in the ITS file.
This series improves the robustness of FIT image generation and helps
catch malformed image trees during build time.
Link: https://lore.kernel.org/r/20250715130317.3886-1-aristo.chen@canonical.com
|
|
mkimage introduced a validation step to ensure that the 'default'
property under the /configurations node in a FIT image refers to a
valid subnode. This exposed an issue in the
k3-am65-iot2050-boot-image.dtsi, where the 'default' property was set to
"ti/k3-am6528-iot2050-basic" and "ti/k3-am6528-iot2050-basic-pg2", which
do not correspond to actual configuration node names.
This patch updates both /configurations nodes to reference the correct
subnode.
Without this fix, mkimage will fail with an error:
"ERROR: Default configuration 'ti/k3-am6528-iot2050-basic' not found
under /configurations"
An upcoming commit will validate the if the default configuration exists
Signed-off-by: Aristo Chen <aristo.chen@canonical.com>
|
|
We are now using the DM code for the i2c mux and to read out the
inventory eeprom. Therefore we need to add the nodes to the specific DTS
files.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
|
|
KASLR, or Kernel Address Space Layout Randomization, is a security
feature in the Linux kernel that randomizes the memory location
where the kernel is loaded during boot.
OP-TEE RNG is a Random Number Generator (RNG) component within the
Open Portable Trusted Execution Environment (OP-TEE) which provides
a random number to U-BOOT and U-BOOT provides this random number
as seed value to the LINUX kernel for KASLR.
Add KASLR OPTEE RNG support across K3 devices by enabling the required
configs.
Signed-off-by: Gokul Praveen <g-praveen@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
|
|
In order to compile more drivers, add an empty sync() function.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27088
- Add support for the i.MX95 B0 version.
- Enable standard boot for phycore-imx8mp.
- Kconfig fixes for i.MX MMC and FSL_SEC_MON.
- Support 4Gb single die variant of the i.MX8MM Venice board.
|
|
These erratas are only useful if USB is enabled. If it is disabled
these erratas might cause issues.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
|
|
Make temperature unit (celsius) more clear to reduce confusion.
Signed-off-by: David Zang <davidzangcs@gmail.com>
|
|
The options related to FSL_SEC_MON are part of the chain of trust
related options and should be under that menu, so move it there.
Furthermore we don't need to prompt for the driver itself but do need to
allow for configuration of the monitor endianess.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As no platforms use this driver anymore, remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
i.MX95 B0 uses image container format v2 and needs DUMMY_DDR so that
update imximage.cfg and container.cfg for it.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
|
|
To support PQC container format which is used for post quantum
authentication on new i.MX parts like i.MX94
The major changes compared to legacy container format is in
signature block, new container tag and version, and new alignment
of container header.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
|
|
Since i.MX94, the ELE get_info structure is updated to add
OEM PQC SRK hash, so update it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
|
|
TH1520 SoC ships two MAC controllers based on Designware Ethernet IP
that are capable of Gigabit operation. Describe them in SoC devicetree
and enable them for Lichee Pi 4A.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
TH1520 SoC ships DMA peripherals that could only reach the first 32-bit
range of memory, for example, the GMAC controllers. Let's limit the
usable top of RAM below 4GiB to ensure DMA allocations are accessible to
all peripherals.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
The stdout-path property is already set to this value in the other
chosen node ~15 lines above.
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
|
|
This symbol is not something that the user should be enabling or
disabling but rather the developer for a particular board should select
it when required.
This is mostly size neutral, however a few places do have changes. In
the case of i.MX6ULL systems, it is always the case that
arch_misc_init() could call setup_serial_number() and do useful work,
but was not enabled widely, but now is. In the case of i.MX23/28
systems, we should be able to call mx28_fixup_vt() again here, so do so.
Finally, some platforms were calling arch_misc_init() and then not doing
anything and this results in removing the option.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Svyatoslav Ryhel <clamor95@gmail.com> says:
Add uclass for HW AES cryptographic devices found on some devices, like
Tegra20/Tegra30 SoC AES engine.
Link: https://lore.kernel.org/r/20250629105711.24687-1-clamor95@gmail.com
|
|
Create a basic test suit for AES DM uclass that covers all available
operations.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27010
- Fix the i.MX8M Nano GPU path.
- Enable RNG support for KASLR on Toradex i.MX8 boards.
- Enable watchdog and clock driver for imx6ulz_smm_m2b.
- Tighten dependencies on CMD_BLOB.
- Remove the rest of i.MX31 support.
|
|
- SH Ether clean ups, RZ/A1 clean ups, RZ/A1 Genmai support
- Gen3 EEPROM DT node clean up
- V4H SA0 BootROM compatible binman etype, SCIF compatible SREC
generation for Gen4
|
|
Add r7s72100 Genmai board support. Serial console, NOR Flash and
Ethernet are known to work however on-board SDRAM is not yet enabled.
Signed-off-by: Magnus Damm <damm@opensource.se>
|
|
Replace current ad-hoc generation of SA0 header with renesas_rcar4_sa0 binman
etype on Renesas R-Car V4H. The new binman etype generates header which is
almost identical to the current ad-hoc SA0 header, with one difference, the
load length matches the actual payload size, which slightly improves boot time.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Most of the sysinfo EEPROM node eeprom@50 is now part of the core DTs,
remove duplicate DT properties from *-u-boot.dtsi . Adjust the phandle
reference to i2c-eeprom in sysinfo node using <&{i2c_*/eeprom@50}> to
avoid need for DT label. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Add Renesas R-Car Gen4 SCIF/HSCIF loader compatible SREC generation.
This is a regular U-Boot SPL SREC augmented with a short header which
describes where to store the received data and how much data to store.
This header is interpreted by the R-Car Gen4 BootROM SCIF/HSCIF loader.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Convert u-boot-spl.bin instead of u-boot-spl ELF into SCIF loader
compatible SREC. The u-boot-spl.bin includes SPL DT, while the ELF
does not, which leads to failure to start SPL via SCIF loader due
to missing SPL DT. Fix this by using u-boot-spl.bin which includes
the DT.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Add the 16, 32 and 64bit versions of the non-endian {clr,set,clrset}bits
macros.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The SoC node is called 'soc@0', even on NXP branch 6.6-fslc. This fixes
the boot on i.MX8M Nano DualLite, as there is no GPU.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
|
|
With the removal of the last i.MX31 platform we can remove the rest of
the underlying architecture code as well.
Fixes: f247354708ec ("arm: Remove mx31pdk board")
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
|
