| Age | Commit message (Collapse) | Author |
|---|
|
https://source.denx.de/u-boot/custodians/u-boot-socfpga into next
- A new driver in the misc to register setting from device tree. This
also provides user a clean interface and all register settings are
centralized in one place, device tree.
- Enable Agilex5 platform for Intel product. Changes, modification and
new files are created for board, dts, configs and makefile to create
the base for Agilex5.
Build-tested on SoC64 boards, boot tested on some of them.
|
|
Add socfpga_dtreg driver enablement for Intel SoCFPGA.
Signed-off-by: Wan Yee Lau <wan.yee.lau@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip into next
Please pull the updates for rockchip platform:
- Add board: rk3588 Generic, Cool Pi CM5, Theobroma-Systems RK3588 Jaguar SBC,
Toybrick TB-RK3588X;
rk3588s Cool Pi 4B;
rk3566 Pine64 PineTab2;
- Add saradc v2 support;
- Add PMIC RK806 support;
- rk3588 disable force_jtag by default;
- Migrate to use IO-domain driver for all boards;
- Use common bss and stack addresses for rk33xx and rk35xx boards;
- Other updates for driver, config and dts;
|
|
Add support to the RGxx3 device for the Powkiddy RGB10MAX3. This device
is extremely similar to all the other devices and can use the same
bootloader with the same detection logic.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The Pine64 PineTab2 is a tablet computer based on the Rockchip RK3566
SoC. The table features 4/8 GB LPDDR4 RAM and 64/128 GB eMMC storage.
Features tested on a Pine64 PineTab2 8GB v2.0:
- SD-card boot
- eMMC boot
- SPI Flash boot
- USB host
Device tree is imported from linux maintainer branch v6.9-armsoc/dts64,
commit 1b7e19448f8f ("arm64: dts: rockchip: Add devicetree for Pine64
PineTab2").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add a minimal generic RK3588S/RK3588 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3588S/RK3588 boards that follow reference board design.
Also fix the alphabetical order of RK3588 boards listed in Makefile and
documentation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
|
|
TB-RK3588X board is a Rockchip Toybrick RK3588 based development board.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB Memory LPDDR4x
Mali G610MC4 GPU
2× MIPI-CSI0 Connector
1x 2Lanes PCIe3.0 Connector
1x SATA3.0 Connector
32GB eMMC Module
2x USB 2.0, 2x USB 3.0
1x HDMI Output, 1x HDMI Input
2x Ethernet Port
Functions work normally:
[1] USB2.0 Host
[2] Ethernet0 with PHY RTL8211F
More information can be obtained from the following websites:
[1] https://t.rock-chips.com/en/wiki/EN/tb-rk3588x_en/index.html
[2] http://t.rock-chips.com/
Kernel commits:
8ffe365f8dc7 ("arm64: dts: rockchip: Add devicetree support for TB-RK3588X board")
7140387ff49d ("dt-bindings: arm: rockchip: Add Toybrick TB-RK3588X")
Reviewed-by: Weizhao Ouyang <weizhao.ouyang@arm.com>
Signed-off-by: Elon Zhang <zhangzj@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Update defconfig for rk3328-orangepi-r1-plus boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Add PHY_ROCKCHIP_INNO_USB2=y option to support the onboard USB PHY.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Update defconfig for rk3328-nanopi-r2* boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add DM_REGULATOR_GPIO=y and SPL_DM_REGULATOR_GPIO=y to support the
regulator-gpio compatible.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Update defconfig for rk3328-rock-pi-e with new defaults.
Remove the xPL_DRIVERS_MISC=y option, no misc driver is used in xPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_MDIO=y to ensure device tree props can be used by PHY driver.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add myself as a reviewer for this board.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Update defconfig for rk3328-roc-cc with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands. Also add CMD_POWEROFF=y to be able to use the poweroff command.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_MOTORCOMM=y and PHY_REALTEK=y to support common
ethernet PHYs.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree file to MAINTAINERS and add myself as a
reviewer for this board.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The 'rng list' command probes all RNG devices and list those devices
that are successfully probed. Also update the help info.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
|
|
Introduce basic documentation for the am62p family of SoCs.
Signed-off-by: Bryan Brattlof <bb@ti.com>
|
|
This migrates the plaintext README in
board/theobroma-systems/ringneck_px30 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
This migrates the plaintext README in
board/theobroma-systems/puma_rk3399 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
JAGUAR is a Single-Board Computer (SBC) based around the rk3588 SoC and
is targeting Autonomous Mobile Robots (AMR).
It features:
* LPDDR4X (up to 16GB)
* 1Gbps Ethernet on RJ45 connector (KSZ9031 or KSZ9131)
* PCIe 3.0 4-lane on M.2 M-key connector
* PCIe 2.1 1-lane on M.2 E-key
* USB 2.0 on M.2 E-key
* 2x USB3 OTG type-c ports with DP Alt-Mode
* USB2 host port
* HDMI output
* 2x camera connectors, each exposing:
* 2-lane MIPI-CSI
* 1v2, 1v8, 2v8 power rails
* I2C bus
* GPIOs
* PPS input
* CAN
* RS485 UART
* FAN connector
* SD card slot
* eMMC (up to 256GB)
* RTC backup battery
* Companion microcontroller
* ISL1208 RTC emulation
* AMC6821 PWM emulation
* On/off buzzer control
* Secure Element
* 80-pin Mezzanine connector for daughterboards:
* GPIOs
* 1Gbps Ethernet
* PCIe 2.1 1-lane
* 2x 2-lane MIPI-CSI
* ADC channel
* I2C bus
* PWM
* UART
* SPI
* SDIO
* CAN
* I2S
* 1v8, 3v3, 5v0, dc-in (12-24V) power rails
The Device Tree comes from next-20240110 Linux kernel.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
When copying the build system for Linux we missed to replace some
instances of 'Documentation' by 'doc'.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Python 3.6 introduced a DeprecationWarning for invalid escape sequences.
This is upgraded to a SyntaxWarning in Python 3.12, and will eventually
be a syntax error.
Fix these now to get ahead of it before it's an error.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Message-ID: <20230912060801.95533-3-bgray@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Adapted for U-Boot
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Use proper binary artifact names for HSFS devices.
Do not use the *_unsigned binaries.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
When using the previous prototype you got a compiler warning like this:
warning: initialization of 'int (*)(struct cmd_tbl *, int, int, char * const*)' from incompatible pointer type 'int (*)(struct cmd_tbl *, int, int, const char **)' [-Wincompatible-pointer-types]
Fixes: 3d9640f55cb2 ("doc: expand README.commands")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
|
|
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Prepare v2024.04-rc4
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add documentation for PHYTEC phyCORE-AM64x SoM.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
TI K3 J784S4 and AM69 are new additions to the K3 SoC family.
Add documentation about the J784S4 EVM and AM69 SK.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
|
|
The "bootflow" command currently doesn't support scanning a single
partition. This is inconvenient in setups with multiple bootable
partitions within a single disk, but only one is desired.
Support scanning a single disk partition. Specifically, support the
syntax:
bootflow scan mmc1:4
which scans only mmc device 1, partition 4.
Signed-off-by: Nam Cao <namcao@linutronix.de>
|
|
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
|
|
Marek Vasut <marek.vasut+renesas@mailbox.org> says:
Rename R-Mobile to Renesas all over the place because the chips are
made by Renesas, while only a subset of them is from the R-Mobile line.
|
|
Add new renesas entry and update rmobile entry to match.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
In gsub, when the destination string is empty, the string 't' is
provided and the regular expression doesn't match, then the final result
is an empty string.
Example:
=> echo ${foo}
=> setenv foo
=> setexpr foo gsub e a bar
=> echo ${foo}
=>
The variable ${foo} should contain "bar" and the lack of match shouldn't
be considered an error.
This patch fixes the erroneous behavior by removing the return
statement and breaking out of the loop in case of lack of match.
Also add a test for the no match case.
Signed-off-by: Massimiliano Minella <massimiliano.minella@se.com>
|
|
Currently, if boot with extlinux.conf and do not set the fdt
U-Boot will provide its own device tree. This behavior is
beneficial if the U-Boot device tree is in sync with Linux,
but it totally halts the booting of pre-dtb kernels (3.4 for
example) since it uses ATAGs. To fix this, pass `-` in the
fdt extlinux field as a signal that no tree should be used.
Suggested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
The MSM8916/APQ8016 Technical Reference Manual is publicly available and
contains a lot of useful register maps for many core parts of the SoC.
Include an archive.org link to it in the dragonboard410c documentation.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Replace the board specific docs with a generic board.rst file which
documents the build/boot process for the sdm845 and qcs404 boards now
that the only differences are the DTB in use.
At the same time, create a debugging page to document some useful
snippets and tips for working with Qualcomm platforms.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Use the root compatible strings from upstream Linux, add missing
'#clock-cells' property to the gcc node.
Adjust some of the msm8916/apq8016 drivers to use the correct upstream
compatible properties and DT bindings.
This prepares us to switch to upstream DT in a future patch.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The upstream DT is supported here, so drop the U-Boot specific binding
docs.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Encourage SoC/board maintainers to migrate to using devicetree-rebasing
subtree and maintain a regular sync with Linux kernel devicetree files
and bindings.
Along with that add documentation regarding how to run DT bindings
schema checks.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
|
|
Since U-Boot switched away from manual CONFIG_* defines to Kconfig
options, align devicetree documentation accordingly.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add documentation for SPI boot.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
|
|
|
|
Describe how to build and boot for the Sielaff i.MX6 Solo board.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
|
|
Sync usage info with the one cmd/avb.c.
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240209192045.3961832-8-igor.opaniuk@foundries.io
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
With the relatively new button API in U-Boot, it's now much easier to
model the common usecase of mapping arbitrary actions to different
buttons during boot - for example entering fastboot mode, setting some
additional kernel cmdline arguments, or booting with a custom recovery
ramdisk, to name a few.
Historically, this functionality has been implemented in board code,
making it fixed for a given U-Boot binary and requiring the code be
duplicated and modified for every board.
Implement a generic abstraction to run an arbitrary command during boot
when a specific button is pressed. The button -> command mapping is
configured via environment variables with the following format:
button_cmd_N_name=<button label>
button_cmd_N=<command to run>
Where N is the mapping number starting from 0. For example:
button_cmd_0_name=vol_down
button_cmd_0=fastboot usb 0
This will cause the device to enter fastboot mode if volume down is held
during boot.
After we enter the cli loop the button commands are no longer valid,
this allows the buttons to additionally be used for navigating a boot
menu.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Tegra30
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Rework the section about includes slightly. We should not be using
common.h anywhere, so remove that from examples and ask people to send
patches removing it when found. Doing this also means we need to reword
other parts of this section. Be clearer about using alphabetical
ordering.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
|
|
The rendering of the OpenSBI logo should look like the screen output.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Add documentation for imxrt1170-evk.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Add index page entry, adjust formatting.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Add initial support for the PHYTEC phyBOARD-Segin-i.MX93 board based on
the PHYTEC phyCORE-i.MX93 SoM.
Supported features:
- 1GB LPDDR4 RAM
- eMMC
- external SD
- FEC Ethernet
- debug UART
- watchdog
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Tested-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
|
|
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC however this works with the same
config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add document for Milk-V Duo board which based on Sophgo's CV1800B SoC.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
