| Age | Commit message (Collapse) | Author |
|---|
|
J. Neuschäfer <j.ne@posteo.net> says:
This patchset contains a few small fixes/cleanups for the MPC83xx
platform.
Link: https://lore.kernel.org/r/20241220-mpc83xx-misc-v2-0-ff4c17ee5fa4@posteo.net
|
|
The mpc8xxx_gpio driver contains a workaround for certain chips
where the previously written state of outputs cannot be read back
from the GPIO data (GPDAT) register (MPC8572/MPC8536). This workaround
consists of tracking the state of GPDAT in a "shadow register" (i.e. a
software variable). The shadow register is initialized to zero.
This results in a problem w.r.t. outputs that are configured to a
high (1) state before U-Boot runs, but not touched by U-Boot itself:
Due to the zero-initialization, these GPIOs end up being set to zero,
the first time that any other output is set.
To avoid such issues initialize the GPDAT shadow register to the value
previously held by any outputs, if possible. On MPC8572/MPC8536 this
should make no difference, i.e. the shadow register should be
initialized to zero on these chips.
This patch has been tested on a MPC8314E-based board.
Reviewed-by: Sinan Akman <sinan@writeme.com>
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
|
|
Base on GPIO hog to support sgpio persist enable feature.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
Prepare v2025.01-rc5
|
|
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
have_dual_base is set to false, so the 8ulp_data will be put in BSS
section which conflicts with the area of u-boot.dtb which padded just
after u-boot-nodtb.bin. So move 8ulp_data to data section to avoid
its content being corrupted by dtb.
Fixes: 51cfa66f2c4 ("gpio: imx_rgpio2p: support one address")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
not implmentated
Currently in _dm_gpio_set_flags() when set_flags ops is not implemented
direction_output()/_input() is used, but pull up/down is not supported by
these ops.
Signed-off-by: Zixun LI <admin@hifiphile.com>
|
|
Add ops get_dir_flags() to read status from GPIO registers.
Signed-off-by: Zixun LI <admin@hifiphile.com>
|
|
Support GPIO configuration with following flags:
- in, out, out_active
- open_drain, pull_up
Signed-off-by: Zixun LI <admin@hifiphile.com>
|
|
This patch adds support for determining whether a gpio pin is mapped as
peripheral function.
Signed-off-by: Zixun LI <admin@hifiphile.com>
|
|
The qcom_pmic code is broken for new PMICs and should be fixed,
without the QUIRK the code is broken and the GPIOs don't work
anymore on SM8550 and SM8650 platforms.
Partially revert the revert and only add the quirk on the PM8550
PMIC, making the buttons and MMC detect gpio work again.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Billy Tsai <billy_tsai@aspeedtech.com> says:
AST2600 SoC has 2 SGPIO master interfaces one with 128 pins another one
with 80 pins, AST2500/AST2400 SoC has 1 SGPIO master interface that
supports up to 80 pins.
Link: https://lore.kernel.org/r/20241016085955.314236-1-billy_tsai@aspeedtech.com
|
|
The Aspeed SGPIO driver supports the SGPIO controllers found in the
AST2400, AST2500 and AST2600 BMC SoCs. The implementation is a cut-down
copy of the upstream Linux kernel driver, adapted for u-boot.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
|
|
Starting with Linux commit 7569486d79ae ("gpio: dwapb: Add ngpios
DT-property support") the "snps,nr-gpios" property was marked
as deprecated.
And since all newly added dw-apb-gpio nodes are described using generic
"ngpios" property, it's time to add support for it.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
* Fixes a warning about implicit declaration of udelay.
Signed-off-by: Philip Balister <philip@balister.org>
|
|
Assorted Tegra enhancements. Merged with the recent XPL_BUILD changes,
resolve some whitespace issues and fix the name of the new apalis-tk1
env file by Tom.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In some cases access to GPIOs is needed so early that DM
is not ready even nearly. These functions are exactly for
this case.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
|
|
Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
|
|
Use PHASE_ as the symbol to select a particular XPL build. This means
that SPL_TPL_ is no-longer set.
Update the comment in bootstage to refer to this symbol, instead of
SPL_
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Use XPL_ as the symbol to indicate an SPL build. This means that SPL_ is
no-longer set.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/22526
- Add DA9063 watchdog support for the imx6q-lxr2 board.
- Add support for DH electronics i.MX8M Plus DHCOM PicoITX
- Add DH i.MX8MP DHCOM SoM on DRC02 carrier board
- Several fsl_esdhc_imx improvements.
- Pas no-mmc-hs400 to mmc2 on imx8mm-cl-iot-gate.
|
|
This reverts commit 19f000b72b2fa7e4540f7cdb91287aff594239bd.
The bug in writing was caused by a long-standing error in the SPMI
driver which has since been fixed - c2de620d64d4 ("spmi: msm: fix
version 5 support"). We can safely enable writing GPIO configuration
now.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Leverage the data introduced in the struct msm_special_pin_data to allow
setting the gpio direction and value if supported by the pin data.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
So we can disable to build ADP5585 in SPL to save size
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
The PSR register works correctly for GPIO pins in input mode,
but always returns 0 for GPIO pins in output mode unless the SION
bit is set.
The DR register should be used for GPIO pins in output mode
to allow correct getting of previously set output value.
Please note that the Linux gpio-mxc driver and the NXP U-Boot mxc_gpio
driver already use the DR register for all GPIO pins in output mode:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=442b2494b17d1a4f0a14721580271eb23ebffd42
https://github.com/nxp-imx/uboot-imx/commit/4afc3f90943c6b117f79b66d2cd04e64f437b0c2
Signed-off-by: Tomas Paukrt <tomaspaukrt@email.cz>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
|
|
In the 7th generation of the SoC from Aspeed, the control logic of the
GPIO controller has been updated to support per-pin control. Each pin now
has its own 32-bit register, allowing for individual control of the pin’s
value, direction, interrupt type, and other settings.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
|
|
Add Nuvoton BMC NPCM7xx/NPCM8xx sgpio driver.
BMC can use this driver to increase 64 GPI pins and 64 GPO pins to use.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
|
|
Drop all duplicate newlines. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
ZYNQMP_FIRMWARE can be disabled and driver depends on it that's why record
this dependency via Kconfig.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c3ca38fbb2f4e6948a5ef95b369015de96259709.1717685091.git.michal.simek@amd.com
|
|
Add support for AMD Versal Gen 2. SoC is based on Cortex-a78ae 4 cluster/2
cpu core each. A lot of IPs are shared with previous families. There are
couple of new IP blocks where the most interesting from user point of view
is UFS.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/bc2b70831ce1031bd0fac32357bff84936e1310f.1716994063.git.michal.simek@amd.com
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This is used for the volume keys on some SM8150/SM8250 devices.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
As with some other modern PMICs, writing to the GPIOs seems to make the
device reset.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add support for PM8550 GPIO controller variant, keep read-only
until the GPIO and Pinctrl setup is fixed for new PMICs.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
The i.MX8ULP/93 gpio dt-schema have been updated to only have one
address entry, update the driver to support it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-snapdragon
- Ethernet, i2c, and USB support are now enabled by default
- The clock driver gets some bug fixes and cleanup
- Invalid FDTs are now properly detected in board_fdt_blob_setup().
- The pinctrl driver gains preparatory support for per-pin function
muxes.
- Support is added for two generations of Qualcomm HighSpeed USB PHY
- A power domain driver is added for the Globall Distributed Switch
Controllers on the GCC hardware block.
- SDM845 gains USB host mode support.
- OF_LIVE is enabled by default for Qualcomm platforms
- Some U-Boot devicetree compatibility fixups are added during init to
improve compatbility with upstream DT.
|
|
The .direction_input and .direction_output ops are deprecated, and don't
seem to behave properly for us. Implement our own .set_flags op to
handle this correctly.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
|
|
Add support for system power off via UCLASS_SYSRESET. Newer versions of
Turris Omnia MCU firmware can power off the board (MCU will disable
almost all voltage regulators and go into low power mode).
Move the MCU driver into drivers/misc and register it under UCLASS_MISC.
The sysreset and gpio device are bound as child devices of the MCU device.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Update firmware features reading to try reading 32 bits of features and
fallback to reading 16 bits.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Use byteorder conversion function instead of manually assembling data
from/to MCU.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add header containing all MCU command definitions and use it in board
code and in MCU driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
|
|
The U-Boot driver try to base the gpio bank id on the gpio-ranges prop
and fall back to base the bank id on the node name. However, the linux
driver try to base the bank id on the gpio alias id and fall back on
node order.
This can cause issues when SoC DT is synced from linux and gpioX@ nodes
has been renamed to gpio@ and gpio-ranges or a SoC specific alias has
not been assigned.
Try to use the gpio alias id as first fallback when a gpio-ranges prop
is missing to ease sync of updated SoC DT. Keep the current fallback on
node name as a third fallback to not affect any existing unsynced DT.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The different macros use writel which is defined in asm/io.h, so let's
include the header so users of hardware.h do not need to include
asm/io.h as well.
While at it, remove asm/io.h includes wherever
asm/arch-rockchip/hardware.h is included already.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
|
|
Prepare v2024.04-rc4
|
|
Rename ARCH_RMOBILE to ARCH_RENESAS because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'ARCH_RMOBILE' | xargs -I {} sed -i 's@ARCH_RMOBILE@ARCH_RENESAS@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
|
|
- Reworks Qualcomm support to be more generic, dropping board specific
build targets and relying on DT as the only source of truth
- Switches all Qualcomm devices to use upstream devicetree
|
