summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2017-02-17mmc: zynq: Add fdt max-frequency supportStefan Herbrechtsmeier
The maximum supported peripheral clock frequency of the zynq depends on the IO routing. The MIO and EMIO support a maximum frequency of 50 MHz respectively 25 MHz. Use the max-frequency value of the device tree to determine the maximal supported peripheral clock frequency. Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-02-17mmc: zynq: Determine base clock frequency via clock frameworkStefan Herbrechtsmeier
The zynq_sdhci controller driver use CONFIG_ZYNQ_SDHCI_MAX_FREQ as base clock frequency but this clock is not fixed and depends on the hardware configuration. Additionally the value of CONFIG_ZYNQ_SDHCI_MAX_FREQ doesn't match the real base clock frequency of SDIO_FREQ. Use the clock framework to determine the frequency at run time. Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-02-17clk: zynq: Add optional ethernet emio clock source supportStefan Herbrechtsmeier
Add support for the optional ethernet emio clock source to the zynq clock framework driver. Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-02-17zynq: Move zynq to clock frameworkStefan Herbrechtsmeier
Move the zynq to clock framework and remove unused functions as well as the CONFIG_ZYNQ_PS_CLK_FREQ configuration. Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-02-17clk: zynq: Add zynq clock framework driverStefan Herbrechtsmeier
Add a clock framework driver for the zynq platform. The driver is based on the platform zynq clock driver but reworked to use static functions instead of run-time generated objects even for unused clocks. Additionally the CONFIG_ZYNQ_PS_CLK_FREQ is replaced by the ps-clk-frequency from the device tree. Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-02-17net: zynq: Add clk framework support to zynq ethernet driverStefan Herbrechtsmeier
If available use the clock framework to set the tx clock rate of the zynq ethernet controller. Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-02-17net: zynq: Don't overwrite gem_rclk_ctrl with default valueStefan Herbrechtsmeier
The gem[0-1]_rclk_ctrl registers control the source of the rx clock, control and data signals and configure via ps7_init function. Don't overwrite the register with the default value. Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-02-13i2c: sandbox: remove code snippet from Kconfig helpMasahiro Yamada
With the Kconfig re-sync with Linux 4.10, characters such as '}', ';' in Kconfig help message cause warnings: $ make defconfig *** Default configuration is based on 'sandbox_defconfig' drivers/i2c/Kconfig:132:warning: ignoring unsupported character '}' drivers/i2c/Kconfig:132:warning: ignoring unsupported character ';' Drop the Device Tree fragment from the help. Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-12flash: complete CONFIG_SYS_NO_FLASH move with renamingMasahiro Yamada
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-09Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini
2017-02-09omap_hsmmc.c: Fix build warning on non-omap3Tom Rini
It was incorrect to always include "asm/arch-omap3/mux.h" constantly. This introduced warnings on non-omap3 where certain values will conflict between the various families. Conditionally guard the inclusion in order to correct the problem. Fixes: 6aca17c9b7e8 ("drivers: mmc: omap_hsmmc: Fix IO Buffer on OMAP36xx") Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-09Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
2017-02-09mmc: init mmc block devices on probeFiach Antaw
MMC devices accessed exclusively via the driver model were not being initialized before being exposed as block devices, causing issues in scenarios where the MMC device is first accessed via the uclass block interface. Signed-off-by: Fiach Antaw <fiach.antaw@uqconnect.edu.au>
2017-02-09drivers: mmc: omap_hsmmc: Fix IO Buffer on OMAP36xxAdam Ford
On the OMAP36xx/37xx the CONTROL_WKUP_CTRL register has a field (bit 6) named GPIO_IO_PWRDNZ. If 0, the IO buffers which are related to GPIO_126, 127 and 129 are disabled. Some boards may need this for MMC. After the PBIAS is configured, this bit should be set high to enable these GPIO pins. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-02-09mmc: ftsdc021_sdhci: remove the ftsdc021_sdhci.cJaehoon Chung
ftsdc021_sdhci.c is dead file. There is no reason to maintain this host controller. Removes the entire ftsdc021_sdhci.c. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-02-09mmc: mmc-uclass: use the fixed devnum with alias nodeJaehoon Chung
If there are alias nodes as "mmc", use the devnum as alias index number. This patch is for fixing a problem of Exynos4 series. Problem is the below thing. Current legacy mode: EXYNOS DWMMC: 0, SAMSUNG SDHCI: 1 After using DM: SAMSUNG SDHCI: 0, EXYNOS DWMMC: 1 Dev index is swapped. Then u-boot can't find the kernel image..because it is already set to 0 as mmcdev. If change from legacy to DM, also needs to touch all exynos4 config file. For using simply, just supporting the fixed devnum with alias node is better than it. Usage: alaise { .... mmc0 = &sdhci2; /* eMMC */ mmc1 = &sdhci1; /* SD */ ... } Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-02-09power: pmic: add the max8997 controller for DMJaehoon Chung
Add the max8997 controller for Driver model. Exynos4210 is using max8997 pmic controller. (pmic_max8997.c should be deprecated.) Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-02-08net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541John Haechten
Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-08Merge git://git.denx.de/u-boot-dmTom Rini
2017-02-08GPIO: Correct doc typo "confguration" -> "configuration"Robert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2017-02-08regulator: palmas: Fix smps6 - smps9 indicesKeerthy
The array indices used currently are dispalaced by 1 for SMPS6 through SMPS10 in the respective places of voltage and ctrl arrays hence fix the same as to assign the right voltage and ctrl registers. Signed-off-by: Keerthy <j-keerthy@ti.com>
2017-02-08pwm: remove unneeded ifdef CONFIG_DM_PWM ... endifMasahiro Yamada
Both CONFIG_PWM_TEGRA and CONFIG_PWM_EXYNOS depend on CONFIG_DM_PWM, i.e. they are already guarded by Kconfig correctly. Remove unneeded ifdef CONFIG_DM_PWM ... endif. While we are here, let's tidy up alignment and sort the lines alphabetically in Makefile. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-02-08drivers: net: cpsw: Fix reading of mac address for am43 SoCsLokesh Vutla
cpsw driver tries to get macid for am43xx SoCs using the compatible ti,am4372. But not all variants of am43x uses this complatible like epos evm uses ti,am438x. So use a generic compatible ti,am43 to get macid for all am43 based platforms. Tested-by: Aparna Balasubramanian <aparnab@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-02-08aspeed: ast2500: Fix H-PLL and M-PLL clock rate calculationmaxims@google.com
Fix H-PLL and M-PLL rate calculation in ast2500 clock driver. Without this fix, valid setting can lead to division by zero when requesting the rate of H-PLL or M-PLL clocks. Signed-off-by: Maxim Sloyko <maxims@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-02-08cros_ec: i2c: Add support for version 3 of the EC protocolMoritz Fischer
Add support for version 3 of the ec protocol. It basically works by stitching some additional header in front (special command code), and having a result and packet_length stitched on for the reply. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Simon Glass <sjg@chromium.org> Cc: u-boot@lists.denx.de Acked-by: Simon Glass <sjg@chromium.org> Tested on snow: Tested-by: Simon Glass <sjg@chromium.org>
2017-02-08simple-bus: enable support for of-platdataKever Yang
Just do nothing in post_bind if of-platdata enabled, for there is no dm_scan_fdt_dev(). Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Fixed subject line typo: Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08dm: core: Replace of_offset with accessorSimon Glass
At present devices use a simple integer offset to record the device tree node associated with the device. In preparation for supporting a live device tree, which uses a node pointer instead, refactor existing code to access this field through an inline function. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08cros_ec: i2c: Group i2c write / read into single transactionMoritz Fischer
Replace dm_i2c_write() / dm_i2c_read() with transaction using struct i2c_msg[2] in order to allow for i2c controller to detect write/read cycle to emit a repeated start condition. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Simon Glass <sjg@chromium.org> Cc: u-boot@lists.denx.de Acked-by: Simon Glass <sjg@chromium.org> Tested on snow: Tested-by: Simon Glass <sjg@chromium.org>
2017-02-07drivers: net: Provide Kconfig menu for PHYLIBAlex
Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: phy: Improve the Marvell 151x constantsJoe Hershberger
Use some constants for the phy configuration instead of so many magic numbers. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: fec_mxc: Fix corruption of device tree blobDaniel Strnad
Modifying content of dev->name leads to the device tree corruption because it points to the node name located there. Signed-off-by: Daniel Strnad <strnadda@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: designware: Fix for use with current Linux device tree for Meson GXHeiner Kallweit
In Uboot for Meson GX the compatible string in meson-gxbb.dtsi so far is: compatible = "amlogic,meson6-dwmac", "snps,dwmac"; On Linux in the same dt file it's compatible = "amlogic,meson-gx-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac"; To avoid breaking ethernet with the next DT synch from Linux to U-Boot (planned as prerequisite for adding Meson GX MMC driver to U-Boot) add "amlogic,meson-gx-dwmac" to the compatibility list in the designware driver. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: phy: dp83867: Add support for MAC impedance configurationMugunthan V N
Add support for programmable MAC impedance configuration and fix typo in DT impedance parameters names. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: phy: vitesse: Fix cis8204 RGMII_ID codePhil Edworthy
Commit 79e86ccb3786c8b20004db3fa10a70049456f580 "vitesse: remove duplicated argument to ||" correctly removed a redundant check. However, I believe that the original code was simply wrong, and should have been checking against RGMII_ID. To fix this and avoid similar problems in the future, use the phy_interface_is_rgmii helper function. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: phy: Marvell: Use phy_interface_is_rgmii helper functionPhil Edworthy
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: phy: Add support for Marvell M88E1512Phil Edworthy
This device also works with the 88E1518 code, so we just adjust the UID mask accordingly. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: phy: Fix mask so that we can identify Marvell 88E1518Phil Edworthy
The mask for the 88E1510 meant that the 88E1518 code would never be used. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: phy: ti: Fix dp83867 RGMII_TXID interface pathPhil Edworthy
There is code that is specifically for RGMII_TXID interface, but this will never get used because the code checks that the RGMII interface is RGMII_ID to RGMII_RXID; RGMII_TXID is after this. To fix this and avoid similar problems in the future, use the phy_interface_is_rgmii helper function. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: macb: Remove redundant #ifdef CONFIG_DM_ETHWenyou Yang
Remove the redundant #ifdef CONFIG_DM_ETH/#endif. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: macb: Add the clock supportWenyou Yang
Due to introducing the at91 clock driver, add the clock support. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: Kconfig: Add CONFIG_MACB optionWenyou Yang
Add CONFIG_MACB option in KConfig to be used to select the Cadence MACB Ethernet driver. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-02-06x86: Don't try to run the VGA BIOS in 64-bit modeSimon Glass
This is not supported, so disable it for now. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-02-06x86: ivybridge: Fix types for 64-bit compilationSimon Glass
Fix a few types that causes warnings on 64-bit machines. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-02-06x86: ivybridge: Declare global data where it is usedSimon Glass
Some files are missing this declaration. Add it to avoid build errors when we actually need the declaration. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-02-06x86: Use unsigned long for address in table generationSimon Glass
We should use unsigned long rather than u32 for addresses. Update this so that the table-generation code builds correctly on 64-bit machines. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-02-06spl: Allow PCH drivers to be used in SPLSimon Glass
Add an option for building Platorm Controller Hub drivers in SPL. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-02-06spl: Allow timer drivers to be used in SPLSimon Glass
Add a new Kconfig option to allow timer drivers to be used in SPL. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-02-06spl: Allow RTC drivers to be used in SPLSimon Glass
Add a new Kconfig option to allow RTC drivers to be used in SPL. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-02-06spl: Allow PCI drivers to be used in SPLSimon Glass
Add a new Kconfig option to allow PCI drivers to be used in SPL. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-02-06spl: Allow CPU drivers to be used in SPLSimon Glass
Add a new Kconfig option to allow CPU drivers to be used in SPL. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
generated by cgit v1.2.3 (git 2.0.4) at 2025-11-02 20:29:54 +0000