summaryrefslogtreecommitdiff
path: root/include/configs/am43xx_evm.h
AgeCommit message (Collapse)Author
2015-07-27configs: split ti_armv7_common into a omap generic headerNishanth Menon
TI armv7 based SoCs are based on two architectures - one based on OMAP generation architecture and others based on Keystone architecture. Many of the options are architecture specific, however a lot are common with v7 architecture. So, step 1 will be to move out OMAP specific stuff from ti_armv7_common into a ti_armv7_omap.h header which is then used by all the relevant architecture headers. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Nishanth Menon <nm@ti.com>
2015-07-22usb: USB download gadget and functions config options coherent namingPaul Kocialkowski
This introduces a coherent scheme for naming USB download gadget and functions config options. The download USB gadget config option is moved to CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each function's config option is moved to a CONFIG_USB_FUNCTION_ prefix. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
2015-07-22usb: xhci: omap: Remove common dwc3 drv functions callsRamneek Mehresh
Remove all redundant dwc3 driver function calls that are defined by dwc3 driver Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2015-07-01defconfig: Move CONFIG_SPI_FLASH_BAR from configsJagan Teki
This commit moves: - CONFIG_SPI_FLASH_BAR from include/configs/*.h into configs/*_defconfigs Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-06-25Move defaults from config_cmd_default.h to KconfigJoe Hershberger
This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25Move default y configs out of arch/board KconfigJoe Hershberger
Some archs/boards specify their own default by pre-defining the config which causes the Kconfig system to mix up the order of the configs in the defconfigs... This will cause merge pain if allowed to proliferate. Remove the configs that behave this way from the archs. A few configs still remain, but that is because they only exist as defaults and do not have a proper Kconfig entry. Those appear to be: SPIFLASH DISPLAY_BOARDINFO Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates, drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-19am43xx_evm: add eth boot supportMugunthan V N
add cpsw ethernet boot mode support to download spl and u-boot.img via tftp protocol. Also adding a seperate config for ethernet boot mode as the default build falcon mode and environment on MMC is defined for ethernet boot mode environment should be set to nowhere. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19am43xx_evm: add usb host boot supportMugunthan V N
While booting via usb host mode, ROM uses DMA to copy MLO over USB so ARM internal RAM cannot be used. Adding USB host boot support by introducing new config target which sets SPL_TEXT_BASE to OCMC ram. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-19am43xx: Update CONFIG_SPL_TEXT_BASETom Rini
With 1.2 silicon this is now the documented starting usable point for downloading images to (and corrects a problem with peripheral booting with prior silicon). Prior silicon is OK using this address as well. Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-06-15ARM: AM43x: Fix MAX_RAM_BANK_SIZELokesh Vutla
On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf. But MAX_RAM_BANK_SIZE is defined as 1GB. Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx. Reported-by: Shivasharan Nagalikar <shivasharan.nagalikar@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-15am43xx_evm: Enable NAND bootTom Rini
Enable booting from NAND on the am437xx-evm. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-15am335x_evm: am44xx_evm: dra7xx_evm: nand: Fix file-system partition nameRoger Quadros
We almost always use UBIFS for user accessible NAND file systems and the UBIFS file system might contain more than one volume within the single NAND partition. The last NAND partition is therefore more appropriately named as "NAND.file-system" instead of "NAND.rootfs" The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the last NAND partition. This patch makes the partition name consistent between u-boot and the kernel. Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-06-02configs: remove CONFIG_NET_MULTILars Poeschel
CONFIG_NET_MULTI is not used anywhere and thus can safely be removed from the configs. Acked-by: Marek Vasut <marex@denx.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
2015-06-01net: Move the CMD_NET config to defconfigsJoe Hershberger
This also selects CONFIG_NET for any CONFIG_CMD_NET board. Remove the imx default for CONFIG_NET. This moves the config that was defined by 60296a8 (commands: add more command entries in Kconfig). Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-05-08ti: am335x/am437x/omap5 devices: Unify network environment variablesCooper Jr., Franklin
Across several devices network environment variables are duplicated. Move these variables to a common include file which insures the environment variables are reused and insures devices across product lines share the same values. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-14include: configs: Enable DWC3 and DFU in AM43xxKishon Vijay Abraham I
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled support for DFU. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-01-13board: ti: am43xx: add support for AM43xx Industrial Development KitFelipe Balbi
AM43xx Industrial Development Kit is a new board based on AM437x line of SoCs. Targetted at Industrial Automation applications, it comes with EtherCAT, motor control and other goodies. Thanks to James Doublesin for all the help. Cc: James Doublesin <doublesin@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-05TI: armv7: enable UUID and PARTNishanth Menon
Enable UUID and partition support for scripted handling platforms with MMC and eMMC and varied partitioning schemes And remove it from headers that end up redefining it. Signed-off-by: Nishanth Menon <nm@ti.com>
2014-10-23arm: am43xx: switch over to CONFIG_ENV_IS_IN_FATFelipe Balbi
By using CONFIG_ENV_IS_IN_FAT it's far easier to have a private, minimal environment for e.g. booting off of network or mounting rootfs on NFS without having to modify the configuration header. Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-08-25board/ti/am43xx: add support for parallel NANDpekon gupta
This patch adds support for NAND device connected to GPMC chip-select on following AM43xx EVM boards. am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a time either eMMC or NAND can be enabled. Selection between eMMC and NAND is controlled by: (a) Statically using Jumper on connecter (J89) present on board. (a) If Jumper on J89 is NOT used, then selection can be dynamically controlled by driving SPI2_CS0[MUX_MODE=GPIO] pin via software: SPI2_CS0 == 0: NAND (default) SPI2_CS0 == 1: eMMC am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI, Thus only one of the two can be used at a time. Selection is controlled by: (a) Dynamically driving following GPIO pin from software GPMC_A0(GPIO) == 0 NAND is selected (default) NAND device (MT29F4G08AB) on these boards has: - data-width=8bits - blocksize=256KB - pagesize=4KB - oobsize=224 bytes For above NAND device, ROM code expects the boot-loader to be flashed in BCH16 ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs. Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25tps65218/am43xx_evm: Add power framework support to TPS65218Tom Rini
Add in an init function for the drivers/power framework so we can dump and read the registers via i2c. Cc: Ɓukasz Majewski <l.majewski@samsung.com> Signed-off-by: Tom Rini <trini@ti.com>
2014-06-19board: ti: am43xx: add support for AM43xx Starter KitFelipe Balbi
AM43xx Starter Kit is a new board based on AM437x line of SoCs. Being a low-cost EVM and small size EVM are intended to provide an entry level development platform on a full fledged Hardware System. Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-06-06arm:am43xx: Add TPS65218 support to scale voltages upTom Rini
This family is supported by the TPS65218 PMIC. Implement a scale_vcores to set the MPU and CORE voltage correctly to the max frequency that is supported (and what we will be scaling them to in setup_dplls()). Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06ARM: AM43xx: Fix mmcboot command in EXTRA_ENV_SETTINGSLokesh Vutla
loadbootenv expects devtype variable to be set. This is missing in mmcboot command. With this the following error comes: U-Boot# run mmcboot mmc0 is current device SD/MMC found on device 0 ** Bad device usb 0 ** ** Bad device usb 0 ** Fixing this by setting devtype as mmc. Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-06-06arm:am33xx: Rework s_init and add board_early_init_fTom Rini
With the changes to the i2c framework (and adopting the omap24xx_i2c driver to them) we can no longer call i2c functions prior to gd having been set and cleared. When SPL booting, this is handled by setting gd to point to SRAM in s_init. However in the cases where we are loaded directly by ROM (memory mapped NOR or QSPI) we need to make use of the normal hooks to slightly delay these calls. Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06am43xx_evm: Add qspiboot targetSourav Poddar
The ePOS EVM and EVM SK have QSPI as an option to boot. Add a qspiboot target that utilizes QSPI for env and so forth as an example of best practices. As QSPI is booted from directly we need to chang CONFIG_SYS_TEXT_BASE. Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices we need to handle that elsewhere, once NAND support is also added. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17am43xx_evm: Drop SPI SPLTom Rini
QSPI booting on this board does not use SPL, so drop SPI-SPL related options. Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17TI:armv7: Change Falcon Mode DT load addressTom Rini
In general, we want to load the DT at base+128MB, so that we ahve sufficient room for the kernel and a larger device tree. In the case of OMAP3, use 64MB instead as we have a number of boards with 128MB DDR. Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17am43xx_evm: Update the ramdisk args, we pass things in just fine via DTTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17TI: Add, use a DEFAULT_LINUX_BOOT_ENV environment stringTom Rini
To deal with a reoccurring problem properly we need to specify addresses for the Linux kernel, Flatted Device Tree and ramdisk that obey the constraints within the kernel's Documentation/arm/Booting file but also make sure that we relocate things within a valid address range. It is possible with these addresses to also set fdt_high and initrd_high to the value of 0xffffffff. We don't do this by default to allow for the most likely success of people using custom addresses however. Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04ARM: AM43xx: Add Ethernet boot support to SPLMugunthan V N
Add Ethernet Boot support to SPL Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04ARM: AM43xx: Add CPSW support to AM43xx EPOS and GP EVMMugunthan V N
Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected to RMII and RGMII phy respectively and enable cpsw in config. Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-02-26Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
Conflicts: arch/arm/cpu/armv7/config.mk board/ti/am43xx/mux.c include/configs/am43xx_evm.h Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21am43xx_evm: Enable GPT commandsTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
2014-02-18am437x_epos_evm: add SPL API, QSPI, and serial flash supportSourav Poddar
Enables support for SPI SPL, QSPI and Spansion serial flash device on the EVM. Configures pin muxes for QSPI mode. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-29Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-01-24arm: am43xx: Add USB spl boot supportDan Murphy
Add the USB host boot support for the am43xx evm Add the macros to boot from a usb drive in uBoot Signed-off-by: Dan Murphy <dmurphy@ti.com>
2014-01-24am43xx_evm.h: Correct SPL max sizeTom Rini
Upon further inspection of relevant parts of the architecture, the maximum SPL binary size is 220KiB. Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-12-18ARM: AM43XX: board: add support for reading onboard EEPROMSekhar Nori
Add support for reading onboard EEPROM to enable board detection. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: Add extra ENV settingsLokesh Vutla
Add Extra env settings. This is derived from am335x Extra ENV settings. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: Add L2 SupportLokesh Vutla
AM4372 uses PL310 L2 Cache. Enable the configs for the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: Adapt to ti_armv7_common.h config fileLokesh Vutla
Use ti_armv7_common.h config file to inclde the common configs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-11-04config: remove platform CONFIG_SYS_HZ definition part 2/2Rob Herring
Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-10-20usb: am437x: Add support for am437x xhci USB hostDan Murphy
Add the support for the am437x xhci usb host. The xHCI host on AM437 is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-15ARM: AM43xx: Add config fileLokesh Vutla
Add config file Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>