From c74b2108e31fe09bd1c5d291c3cf360510d4f13e Mon Sep 17 00:00:00 2001 From: Sergey Kubushyn Date: Fri, 10 Aug 2007 20:26:18 +0200 Subject: [ARM] TI DaVinci support, hopefully final Add support for the following DaVinci boards: - DV_EVM - SCHMOOGIE - SONATA Changes: - Split into separate board directories - Removed changes to MTD_DEBUG (or whatever it's called) - New CONFIG_CMD party line followed - Some cosmetic fixes, cleanup etc. - Patches against the latest U-Boot tree as of now. - Fixed CONFIG_CMD_NET in net files. - Fixed CONFIG_CMD_EEPROM for schmoogie. - Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and DV_EVM. Can't check if it works on SONATA, don't have a board any more, but it at least compiles. Here is an excerpt from session log on SCHMOOGIE... U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17) DRAM: 128 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock : 297MHz DDR Clock : 162MHz ETH PHY : DP83848 @ 0x01 U-Boot > iprobe Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F U-Boot > ping 192.168.253.10 host 192.168.253.10 is alive U-Boot > Signed-off-by: Sergey Kubushyn Acked-by: Dirk Behme Acked-by: Zach Sadecki Acked-by: Stefan Roese --- board/davinci/dv-evm/Makefile | 52 +++++++ board/davinci/dv-evm/board_init.S | 29 ++++ board/davinci/dv-evm/config.mk | 39 ++++++ board/davinci/dv-evm/dv_board.c | 211 +++++++++++++++++++++++++++++ board/davinci/dv-evm/u-boot.lds | 52 +++++++ board/davinci/schmoogie/Makefile | 52 +++++++ board/davinci/schmoogie/board_init.S | 29 ++++ board/davinci/schmoogie/config.mk | 39 ++++++ board/davinci/schmoogie/dv_board.c | 253 +++++++++++++++++++++++++++++++++++ board/davinci/schmoogie/u-boot.lds | 52 +++++++ board/davinci/sonata/Makefile | 52 +++++++ board/davinci/sonata/board_init.S | 100 ++++++++++++++ board/davinci/sonata/config.mk | 39 ++++++ board/davinci/sonata/dv_board.c | 208 ++++++++++++++++++++++++++++ board/davinci/sonata/u-boot.lds | 52 +++++++ 15 files changed, 1259 insertions(+) create mode 100644 board/davinci/dv-evm/Makefile create mode 100644 board/davinci/dv-evm/board_init.S create mode 100644 board/davinci/dv-evm/config.mk create mode 100644 board/davinci/dv-evm/dv_board.c create mode 100644 board/davinci/dv-evm/u-boot.lds create mode 100644 board/davinci/schmoogie/Makefile create mode 100644 board/davinci/schmoogie/board_init.S create mode 100644 board/davinci/schmoogie/config.mk create mode 100644 board/davinci/schmoogie/dv_board.c create mode 100644 board/davinci/schmoogie/u-boot.lds create mode 100644 board/davinci/sonata/Makefile create mode 100644 board/davinci/sonata/board_init.S create mode 100644 board/davinci/sonata/config.mk create mode 100644 board/davinci/sonata/dv_board.c create mode 100644 board/davinci/sonata/u-boot.lds (limited to 'board') diff --git a/board/davinci/dv-evm/Makefile b/board/davinci/dv-evm/Makefile new file mode 100644 index 0000000000..fa0013811d --- /dev/null +++ b/board/davinci/dv-evm/Makefile @@ -0,0 +1,52 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# Copyright (C) 2007 Sergey Kubushyn +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := dv_board.o +SOBJS := board_init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak *~ .depend + +######################################################################### +# This is for $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/davinci/dv-evm/board_init.S b/board/davinci/dv-evm/board_init.S new file mode 100644 index 0000000000..22d8adc18c --- /dev/null +++ b/board/davinci/dv-evm/board_init.S @@ -0,0 +1,29 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn + * + * Board-specific low level initialization code. Called at the very end + * of cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no + * initialization required. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + +.globl dv_board_init +dv_board_init: + + mov pc, lr diff --git a/board/davinci/dv-evm/config.mk b/board/davinci/dv-evm/config.mk new file mode 100644 index 0000000000..aa89d0ec8a --- /dev/null +++ b/board/davinci/dv-evm/config.mk @@ -0,0 +1,39 @@ +# +# (C) Copyright 2002 +# Gary Jennejohn, DENX Software Engineering, +# David Mueller, ELSOFT AG, +# +# (C) Copyright 2003 +# Texas Instruments, +# Swaminathan +# +# Davinci EVM board (ARM925EJS) cpu +# see http://www.ti.com/ for more information on Texas Instruments +# +# Davinci EVM has 1 bank of 256 MB DDR RAM +# Physical Address: +# 8000'0000 to 9000'0000 +# +# Copyright (C) 2007 Sergey Kubushyn +# +# Visioneering Corp. Sonata board (ARM926EJS) cpu +# +# Sonata board has 1 bank of 128 MB DDR RAM +# Physical Address: +# 8000'0000 to 8800'0000 +# +# Razorstream, LLC. SCHMOOGIE board (ARM926EJS) cpu +# +# Schmoogie board has 1 bank of 128 MB DDR RAM +# Physical Address: +# 8000'0000 to 8800'0000 +# +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) +# +# we load ourself to 8108 '0000 +# +# + +#Provide at least 16MB spacing between us and the Linux Kernel image +TEXT_BASE = 0x81080000 diff --git a/board/davinci/dv-evm/dv_board.c b/board/davinci/dv-evm/dv_board.c new file mode 100644 index 0000000000..94925ecfb1 --- /dev/null +++ b/board/davinci/dv-evm/dv_board.c @@ -0,0 +1,211 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn + * + * Parts are shamelessly stolen from various TI sources, original copyright + * follows: + * ----------------------------------------------------------------- + * + * Copyright (C) 2004 Texas Instruments. + * + * ---------------------------------------------------------------------------- + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + */ + +#include +#include +#include +#include + +#define MACH_TYPE_DAVINCI_EVM 901 + +extern void i2c_init(int speed, int slaveaddr); +extern void timer_init(void); +extern int eth_hw_init(void); +extern phy_t phy; + + +/* Works on Always On power domain only (no PD argument) */ +void lpsc_on(unsigned int id) +{ + dv_reg_p mdstat, mdctl; + + if (id >= DAVINCI_LPSC_GEM) + return; /* Don't work on DSP Power Domain */ + + mdstat = REG_P(PSC_MDSTAT_BASE + (id * 4)); + mdctl = REG_P(PSC_MDCTL_BASE + (id * 4)); + + while (REG(PSC_PTSTAT) & 0x01) {;} + + if ((*mdstat & 0x1f) == 0x03) + return; /* Already on and enabled */ + + *mdctl |= 0x03; + + /* Special treatment for some modules as for sprue14 p.7.4.2 */ + if ( (id == DAVINCI_LPSC_VPSSSLV) || + (id == DAVINCI_LPSC_EMAC) || + (id == DAVINCI_LPSC_EMAC_WRAPPER) || + (id == DAVINCI_LPSC_MDIO) || + (id == DAVINCI_LPSC_USB) || + (id == DAVINCI_LPSC_ATA) || + (id == DAVINCI_LPSC_VLYNQ) || + (id == DAVINCI_LPSC_UHPI) || + (id == DAVINCI_LPSC_DDR_EMIF) || + (id == DAVINCI_LPSC_AEMIF) || + (id == DAVINCI_LPSC_MMC_SD) || + (id == DAVINCI_LPSC_MEMSTICK) || + (id == DAVINCI_LPSC_McBSP) || + (id == DAVINCI_LPSC_GPIO) + ) + *mdctl |= 0x200; + + REG(PSC_PTCMD) = 0x01; + + while (REG(PSC_PTSTAT) & 0x03) {;} + while ((*mdstat & 0x1f) != 0x03) {;} /* Probably an overkill... */ +} + +void dsp_on(void) +{ + int i; + + if (REG(PSC_PDSTAT1) & 0x1f) + return; /* Already on */ + + REG(PSC_GBLCTL) |= 0x01; + REG(PSC_PDCTL1) |= 0x01; + REG(PSC_PDCTL1) &= ~0x100; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) |= 0x03; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) &= 0xfffffeff; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) |= 0x03; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) &= 0xfffffeff; + REG(PSC_PTCMD) = 0x02; + + for (i = 0; i < 100; i++) { + if (REG(PSC_EPCPR) & 0x02) + break; + } + + REG(PSC_CHP_SHRTSW) = 0x01; + REG(PSC_PDCTL1) |= 0x100; + REG(PSC_EPCCR) = 0x02; + + for (i = 0; i < 100; i++) { + if (!(REG(PSC_PTSTAT) & 0x02)) + break; + } + + REG(PSC_GBLCTL) &= ~0x1f; +} + + +int board_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + + /* arch number of the board */ + gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_EVM; + + /* address of boot parameters */ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + + /* Workaround for TMS320DM6446 errata 1.3.22 */ + REG(PSC_SILVER_BULLET) = 0; + + /* Power on required peripherals */ + lpsc_on(DAVINCI_LPSC_EMAC); + lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER); + lpsc_on(DAVINCI_LPSC_MDIO); + lpsc_on(DAVINCI_LPSC_I2C); + lpsc_on(DAVINCI_LPSC_UART0); + lpsc_on(DAVINCI_LPSC_TIMER1); + lpsc_on(DAVINCI_LPSC_GPIO); + + /* Powerup the DSP */ + dsp_on(); + + /* Bringup UART0 out of reset */ + REG(UART0_PWREMU_MGMT) = 0x0000e003; + + /* Enable GIO3.3V cells used for EMAC */ + REG(VDD3P3V_PWDN) = 0; + + /* Enable UART0 MUX lines */ + REG(PINMUX1) |= 1; + + /* Enable EMAC and AEMIF pins */ + REG(PINMUX0) = 0x80000c1f; + + /* Enable I2C pin Mux */ + REG(PINMUX1) |= (1 << 7); + + /* Set the Bus Priority Register to appropriate value */ + REG(VBPR) = 0x20; + + timer_init(); + + return(0); +} + +int misc_init_r (void) +{ + u_int8_t tmp[20], buf[10]; + int i = 0; + int clk = 0; + + clk = ((REG(PLL2_PLLM) + 1) * 27) / ((REG(PLL2_DIV2) & 0x1f) + 1); + + printf ("ARM Clock : %dMHz\n", ((REG(PLL1_PLLM) + 1) * 27 ) / 2); + printf ("DDR Clock : %dMHz\n", (clk / 2)); + + /* Set Ethernet MAC address from EEPROM */ + if (i2c_read(CFG_I2C_EEPROM_ADDR, 0x7f00, CFG_I2C_EEPROM_ADDR_LEN, buf, 6)) { + printf("\nEEPROM @ 0x%02x read FAILED!!!\n", CFG_I2C_EEPROM_ADDR); + } else { + tmp[0] = 0xff; + for (i = 0; i < 6; i++) + tmp[0] &= buf[i]; + + if ((tmp[0] != 0xff) && (getenv("ethaddr") == NULL)) { + sprintf((char *)&tmp[0], "%02hhx:%02hhx:%02hhx:%02hhx:%02hhx:%02hhx", + buf[0], buf[1], buf[2], buf[3], buf[4], buf[5]); + setenv("ethaddr", (char *)&tmp[0]); + } + } + + if (!eth_hw_init()) { + printf("ethernet init failed!\n"); + } else { + printf("ETH PHY : %s\n", phy.name); + } + + i2c_read (0x39, 0x00, 1, (u_int8_t *)&i, 1); + + setenv ("videostd", ((i & 0x80) ? "pal" : "ntsc")); + + return(0); +} + +int dram_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + + return(0); +} diff --git a/board/davinci/dv-evm/u-boot.lds b/board/davinci/dv-evm/u-boot.lds new file mode 100644 index 0000000000..710b2a2d6e --- /dev/null +++ b/board/davinci/dv-evm/u-boot.lds @@ -0,0 +1,52 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + . = ALIGN(4); + .text : + { + cpu/arm926ejs/start.o (.text) + *(.text) + } + . = ALIGN(4); + .rodata : { *(.rodata) } + . = ALIGN(4); + .data : { *(.data) } + . = ALIGN(4); + .got : { *(.got) } + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/board/davinci/schmoogie/Makefile b/board/davinci/schmoogie/Makefile new file mode 100644 index 0000000000..fa0013811d --- /dev/null +++ b/board/davinci/schmoogie/Makefile @@ -0,0 +1,52 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# Copyright (C) 2007 Sergey Kubushyn +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := dv_board.o +SOBJS := board_init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak *~ .depend + +######################################################################### +# This is for $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/davinci/schmoogie/board_init.S b/board/davinci/schmoogie/board_init.S new file mode 100644 index 0000000000..22d8adc18c --- /dev/null +++ b/board/davinci/schmoogie/board_init.S @@ -0,0 +1,29 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn + * + * Board-specific low level initialization code. Called at the very end + * of cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no + * initialization required. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + +.globl dv_board_init +dv_board_init: + + mov pc, lr diff --git a/board/davinci/schmoogie/config.mk b/board/davinci/schmoogie/config.mk new file mode 100644 index 0000000000..aa89d0ec8a --- /dev/null +++ b/board/davinci/schmoogie/config.mk @@ -0,0 +1,39 @@ +# +# (C) Copyright 2002 +# Gary Jennejohn, DENX Software Engineering, +# David Mueller, ELSOFT AG, +# +# (C) Copyright 2003 +# Texas Instruments, +# Swaminathan +# +# Davinci EVM board (ARM925EJS) cpu +# see http://www.ti.com/ for more information on Texas Instruments +# +# Davinci EVM has 1 bank of 256 MB DDR RAM +# Physical Address: +# 8000'0000 to 9000'0000 +# +# Copyright (C) 2007 Sergey Kubushyn +# +# Visioneering Corp. Sonata board (ARM926EJS) cpu +# +# Sonata board has 1 bank of 128 MB DDR RAM +# Physical Address: +# 8000'0000 to 8800'0000 +# +# Razorstream, LLC. SCHMOOGIE board (ARM926EJS) cpu +# +# Schmoogie board has 1 bank of 128 MB DDR RAM +# Physical Address: +# 8000'0000 to 8800'0000 +# +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) +# +# we load ourself to 8108 '0000 +# +# + +#Provide at least 16MB spacing between us and the Linux Kernel image +TEXT_BASE = 0x81080000 diff --git a/board/davinci/schmoogie/dv_board.c b/board/davinci/schmoogie/dv_board.c new file mode 100644 index 0000000000..b15c5f7189 --- /dev/null +++ b/board/davinci/schmoogie/dv_board.c @@ -0,0 +1,253 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn + * + * Parts are shamelessly stolen from various TI sources, original copyright + * follows: + * ----------------------------------------------------------------- + * + * Copyright (C) 2004 Texas Instruments. + * + * ---------------------------------------------------------------------------- + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + */ + +#include +#include +#include +#include + +#define MACH_TYPE_SCHMOOGIE 1255 + +extern void i2c_init(int speed, int slaveaddr); +extern void timer_init(void); +extern int eth_hw_init(void); +extern phy_t phy; + + +/* Works on Always On power domain only (no PD argument) */ +void lpsc_on(unsigned int id) +{ + dv_reg_p mdstat, mdctl; + + if (id >= DAVINCI_LPSC_GEM) + return; /* Don't work on DSP Power Domain */ + + mdstat = REG_P(PSC_MDSTAT_BASE + (id * 4)); + mdctl = REG_P(PSC_MDCTL_BASE + (id * 4)); + + while (REG(PSC_PTSTAT) & 0x01) {;} + + if ((*mdstat & 0x1f) == 0x03) + return; /* Already on and enabled */ + + *mdctl |= 0x03; + + /* Special treatment for some modules as for sprue14 p.7.4.2 */ + if ( (id == DAVINCI_LPSC_VPSSSLV) || + (id == DAVINCI_LPSC_EMAC) || + (id == DAVINCI_LPSC_EMAC_WRAPPER) || + (id == DAVINCI_LPSC_MDIO) || + (id == DAVINCI_LPSC_USB) || + (id == DAVINCI_LPSC_ATA) || + (id == DAVINCI_LPSC_VLYNQ) || + (id == DAVINCI_LPSC_UHPI) || + (id == DAVINCI_LPSC_DDR_EMIF) || + (id == DAVINCI_LPSC_AEMIF) || + (id == DAVINCI_LPSC_MMC_SD) || + (id == DAVINCI_LPSC_MEMSTICK) || + (id == DAVINCI_LPSC_McBSP) || + (id == DAVINCI_LPSC_GPIO) + ) + *mdctl |= 0x200; + + REG(PSC_PTCMD) = 0x01; + + while (REG(PSC_PTSTAT) & 0x03) {;} + while ((*mdstat & 0x1f) != 0x03) {;} /* Probably an overkill... */ +} + +void dsp_on(void) +{ + int i; + + if (REG(PSC_PDSTAT1) & 0x1f) + return; /* Already on */ + + REG(PSC_GBLCTL) |= 0x01; + REG(PSC_PDCTL1) |= 0x01; + REG(PSC_PDCTL1) &= ~0x100; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) |= 0x03; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) &= 0xfffffeff; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) |= 0x03; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) &= 0xfffffeff; + REG(PSC_PTCMD) = 0x02; + + for (i = 0; i < 100; i++) { + if (REG(PSC_EPCPR) & 0x02) + break; + } + + REG(PSC_CHP_SHRTSW) = 0x01; + REG(PSC_PDCTL1) |= 0x100; + REG(PSC_EPCCR) = 0x02; + + for (i = 0; i < 100; i++) { + if (!(REG(PSC_PTSTAT) & 0x02)) + break; + } + + REG(PSC_GBLCTL) &= ~0x1f; +} + + +int board_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + + /* arch number of the board */ + gd->bd->bi_arch_number = MACH_TYPE_SCHMOOGIE; + + /* address of boot parameters */ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + + /* Workaround for TMS320DM6446 errata 1.3.22 */ + REG(PSC_SILVER_BULLET) = 0; + + /* Power on required peripherals */ + lpsc_on(DAVINCI_LPSC_EMAC); + lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER); + lpsc_on(DAVINCI_LPSC_MDIO); + lpsc_on(DAVINCI_LPSC_I2C); + lpsc_on(DAVINCI_LPSC_UART0); + lpsc_on(DAVINCI_LPSC_TIMER1); + lpsc_on(DAVINCI_LPSC_GPIO); + + /* Powerup the DSP */ + dsp_on(); + + /* Bringup UART0 out of reset */ + REG(UART0_PWREMU_MGMT) = 0x0000e003; + + /* Enable GIO3.3V cells used for EMAC */ + REG(VDD3P3V_PWDN) = 0; + + /* Enable UART0 MUX lines */ + REG(PINMUX1) |= 1; + + /* Enable EMAC and AEMIF pins */ + REG(PINMUX0) = 0x80000c1f; + + /* Enable I2C pin Mux */ + REG(PINMUX1) |= (1 << 7); + + /* Set the Bus Priority Register to appropriate value */ + REG(VBPR) = 0x20; + + timer_init(); + + return(0); +} + +int misc_init_r (void) +{ + u_int8_t tmp[20], buf[10]; + int i = 0; + int clk = 0; + + /* Set serial number from UID chip */ + u_int8_t crc_tbl[256] = { + 0x00, 0x5e, 0xbc, 0xe2, 0x61, 0x3f, 0xdd, 0x83, + 0xc2, 0x9c, 0x7e, 0x20, 0xa3, 0xfd, 0x1f, 0x41, + 0x9d, 0xc3, 0x21, 0x7f, 0xfc, 0xa2, 0x40, 0x1e, + 0x5f, 0x01, 0xe3, 0xbd, 0x3e, 0x60, 0x82, 0xdc, + 0x23, 0x7d, 0x9f, 0xc1, 0x42, 0x1c, 0xfe, 0xa0, + 0xe1, 0xbf, 0x5d, 0x03, 0x80, 0xde, 0x3c, 0x62, + 0xbe, 0xe0, 0x02, 0x5c, 0xdf, 0x81, 0x63, 0x3d, + 0x7c, 0x22, 0xc0, 0x9e, 0x1d, 0x43, 0xa1, 0xff, + 0x46, 0x18, 0xfa, 0xa4, 0x27, 0x79, 0x9b, 0xc5, + 0x84, 0xda, 0x38, 0x66, 0xe5, 0xbb, 0x59, 0x07, + 0xdb, 0x85, 0x67, 0x39, 0xba, 0xe4, 0x06, 0x58, + 0x19, 0x47, 0xa5, 0xfb, 0x78, 0x26, 0xc4, 0x9a, + 0x65, 0x3b, 0xd9, 0x87, 0x04, 0x5a, 0xb8, 0xe6, + 0xa7, 0xf9, 0x1b, 0x45, 0xc6, 0x98, 0x7a, 0x24, + 0xf8, 0xa6, 0x44, 0x1a, 0x99, 0xc7, 0x25, 0x7b, + 0x3a, 0x64, 0x86, 0xd8, 0x5b, 0x05, 0xe7, 0xb9, + 0x8c, 0xd2, 0x30, 0x6e, 0xed, 0xb3, 0x51, 0x0f, + 0x4e, 0x10, 0xf2, 0xac, 0x2f, 0x71, 0x93, 0xcd, + 0x11, 0x4f, 0xad, 0xf3, 0x70, 0x2e, 0xcc, 0x92, + 0xd3, 0x8d, 0x6f, 0x31, 0xb2, 0xec, 0x0e, 0x50, + 0xaf, 0xf1, 0x13, 0x4d, 0xce, 0x90, 0x72, 0x2c, + 0x6d, 0x33, 0xd1, 0x8f, 0x0c, 0x52, 0xb0, 0xee, + 0x32, 0x6c, 0x8e, 0xd0, 0x53, 0x0d, 0xef, 0xb1, + 0xf0, 0xae, 0x4c, 0x12, 0x91, 0xcf, 0x2d, 0x73, + 0xca, 0x94, 0x76, 0x28, 0xab, 0xf5, 0x17, 0x49, + 0x08, 0x56, 0xb4, 0xea, 0x69, 0x37, 0xd5, 0x8b, + 0x57, 0x09, 0xeb, 0xb5, 0x36, 0x68, 0x8a, 0xd4, + 0x95, 0xcb, 0x29, 0x77, 0xf4, 0xaa, 0x48, 0x16, + 0xe9, 0xb7, 0x55, 0x0b, 0x88, 0xd6, 0x34, 0x6a, + 0x2b, 0x75, 0x97, 0xc9, 0x4a, 0x14, 0xf6, 0xa8, + 0x74, 0x2a, 0xc8, 0x96, 0x15, 0x4b, 0xa9, 0xf7, + 0xb6, 0xe8, 0x0a, 0x54, 0xd7, 0x89, 0x6b, 0x35 + }; + + clk = ((REG(PLL2_PLLM) + 1) * 27) / ((REG(PLL2_DIV2) & 0x1f) + 1); + + printf ("ARM Clock : %dMHz\n", ((REG(PLL1_PLLM) + 1) * 27 ) / 2); + printf ("DDR Clock : %dMHz\n", (clk / 2)); + + /* Set serial number from UID chip */ + if (i2c_read(CFG_UID_ADDR, 0, 1, buf, 8)) { + printf("\nUID @ 0x%02x read FAILED!!!\n", CFG_UID_ADDR); + forceenv("serial#", "FAILED"); + } else { + if (buf[0] != 0x70) { /* Device Family Code */ + printf("\nUID @ 0x%02x read FAILED!!!\n", CFG_UID_ADDR); + forceenv("serial#", "FAILED"); + } + } + /* Now check CRC */ + tmp[0] = 0; + for (i = 0; i < 8; i++) + tmp[0] = crc_tbl[tmp[0] ^ buf[i]]; + + if (tmp[0] != 0) { + printf("\nUID @ 0x%02x - BAD CRC!!!\n", CFG_UID_ADDR); + forceenv("serial#", "FAILED"); + } else { + /* CRC OK, set "serial" env variable */ + sprintf((char *)&tmp[0], "%02hhx%02hhx%02hhx%02hhx%02hhx%02hhx", + buf[6], buf[5], buf[4], buf[3], buf[2], buf[1]); + forceenv("serial#", (char *)&tmp[0]); + } + + if (!eth_hw_init()) { + printf("ethernet init failed!\n"); + } else { + printf("ETH PHY : %s\n", phy.name); + } + + return(0); +} + +int dram_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + + return(0); +} diff --git a/board/davinci/schmoogie/u-boot.lds b/board/davinci/schmoogie/u-boot.lds new file mode 100644 index 0000000000..710b2a2d6e --- /dev/null +++ b/board/davinci/schmoogie/u-boot.lds @@ -0,0 +1,52 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + . = ALIGN(4); + .text : + { + cpu/arm926ejs/start.o (.text) + *(.text) + } + . = ALIGN(4); + .rodata : { *(.rodata) } + . = ALIGN(4); + .data : { *(.data) } + . = ALIGN(4); + .got : { *(.got) } + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/board/davinci/sonata/Makefile b/board/davinci/sonata/Makefile new file mode 100644 index 0000000000..fa0013811d --- /dev/null +++ b/board/davinci/sonata/Makefile @@ -0,0 +1,52 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# Copyright (C) 2007 Sergey Kubushyn +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := dv_board.o +SOBJS := board_init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak *~ .depend + +######################################################################### +# This is for $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/davinci/sonata/board_init.S b/board/davinci/sonata/board_init.S new file mode 100644 index 0000000000..fbb9ea73e9 --- /dev/null +++ b/board/davinci/sonata/board_init.S @@ -0,0 +1,100 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn + * + * Board-specific low level initialization code. Called at the very end + * of cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no + * initialization required. + * + * For _OLDER_ Sonata boards sets up GPIO4 to control NAND WP line. Newer + * Sonata boards, AFAIK, don't use this so it's just return by default. Ask + * Visioneering if they reinvented the wheel once again to make sure :) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + +.globl dv_board_init +dv_board_init: +#ifdef SONATA_BOARD_GPIOWP + /* Set PINMUX0 to enable GPIO4 */ + ldr r0, _PINMUX0 + ldr r1, GPIO4_EN_MASK + ldr r2, [r0] + and r2, r2, r1 + str r2, [r0] + + /* Enable GPIO LPSC module */ + ldr r0, PTSTAT + +gpio_ptstat_loop1: + ldr r2, [r0] + tst r2, $0x00000001 + bne gpio_ptstat_loop1 + + ldr r1, MDCTL_GPIO + ldr r2, [r1] + and r2, r2, $0xfffffff8 + orr r2, r2, $0x00000003 + str r2, [r1] + + orr r2, r2, $0x00000200 + str r2, [r1] + + ldr r1, PTCMD + mov r2, $0x00000001 + str r2, [r1] + +gpio_ptstat_loop2: + ldr r2, [r0] + tst r2, $0x00000001 + bne gpio_ptstat_loop2 + + ldr r0, MDSTAT_GPIO +gpio_mdstat_loop: + ldr r2, [r0] + and r2, r2, $0x0000001f + teq r2, $0x00000003 + bne gpio_mdstat_loop + + /* GPIO4 -> output */ + ldr r0, GPIO_DIR01 + mov r1, $0x10 + ldr r2, [r0] + bic r2, r2, r0 + str r2, [r0] + + /* Set it to 0 (Write Protect) */ + ldr r0, GPIO_CLR_DATA01 + str r1, [r0] +#endif + + mov pc, lr + +#ifdef SONATA_BOARD_GPIOWP +.ltorg + +GPIO4_EN_MASK: + .word 0xf77fffff +MDCTL_GPIO: + .word 0x01c41a68 +MDSTAT_GPIO: + .word 0x01c41868 +GPIO_DIR01: + .word 0x01c67010 +GPIO_CLR_DATA01: + .word 0x01c6701c +#endif diff --git a/board/davinci/sonata/config.mk b/board/davinci/sonata/config.mk new file mode 100644 index 0000000000..aa89d0ec8a --- /dev/null +++ b/board/davinci/sonata/config.mk @@ -0,0 +1,39 @@ +# +# (C) Copyright 2002 +# Gary Jennejohn, DENX Software Engineering, +# David Mueller, ELSOFT AG, +# +# (C) Copyright 2003 +# Texas Instruments, +# Swaminathan +# +# Davinci EVM board (ARM925EJS) cpu +# see http://www.ti.com/ for more information on Texas Instruments +# +# Davinci EVM has 1 bank of 256 MB DDR RAM +# Physical Address: +# 8000'0000 to 9000'0000 +# +# Copyright (C) 2007 Sergey Kubushyn +# +# Visioneering Corp. Sonata board (ARM926EJS) cpu +# +# Sonata board has 1 bank of 128 MB DDR RAM +# Physical Address: +# 8000'0000 to 8800'0000 +# +# Razorstream, LLC. SCHMOOGIE board (ARM926EJS) cpu +# +# Schmoogie board has 1 bank of 128 MB DDR RAM +# Physical Address: +# 8000'0000 to 8800'0000 +# +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) +# +# we load ourself to 8108 '0000 +# +# + +#Provide at least 16MB spacing between us and the Linux Kernel image +TEXT_BASE = 0x81080000 diff --git a/board/davinci/sonata/dv_board.c b/board/davinci/sonata/dv_board.c new file mode 100644 index 0000000000..7b0a459fa3 --- /dev/null +++ b/board/davinci/sonata/dv_board.c @@ -0,0 +1,208 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn + * + * Parts are shamelessly stolen from various TI sources, original copyright + * follows: + * ----------------------------------------------------------------- + * + * Copyright (C) 2004 Texas Instruments. + * + * ---------------------------------------------------------------------------- + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + */ + +#include +#include +#include +#include + +#define MACH_TYPE_SONATA 1254 + +extern void i2c_init(int speed, int slaveaddr); +extern void timer_init(void); +extern int eth_hw_init(void); +extern phy_t phy; + + +/* Works on Always On power domain only (no PD argument) */ +void lpsc_on(unsigned int id) +{ + dv_reg_p mdstat, mdctl; + + if (id >= DAVINCI_LPSC_GEM) + return; /* Don't work on DSP Power Domain */ + + mdstat = REG_P(PSC_MDSTAT_BASE + (id * 4)); + mdctl = REG_P(PSC_MDCTL_BASE + (id * 4)); + + while (REG(PSC_PTSTAT) & 0x01) {;} + + if ((*mdstat & 0x1f) == 0x03) + return; /* Already on and enabled */ + + *mdctl |= 0x03; + + /* Special treatment for some modules as for sprue14 p.7.4.2 */ + if ( (id == DAVINCI_LPSC_VPSSSLV) || + (id == DAVINCI_LPSC_EMAC) || + (id == DAVINCI_LPSC_EMAC_WRAPPER) || + (id == DAVINCI_LPSC_MDIO) || + (id == DAVINCI_LPSC_USB) || + (id == DAVINCI_LPSC_ATA) || + (id == DAVINCI_LPSC_VLYNQ) || + (id == DAVINCI_LPSC_UHPI) || + (id == DAVINCI_LPSC_DDR_EMIF) || + (id == DAVINCI_LPSC_AEMIF) || + (id == DAVINCI_LPSC_MMC_SD) || + (id == DAVINCI_LPSC_MEMSTICK) || + (id == DAVINCI_LPSC_McBSP) || + (id == DAVINCI_LPSC_GPIO) + ) + *mdctl |= 0x200; + + REG(PSC_PTCMD) = 0x01; + + while (REG(PSC_PTSTAT) & 0x03) {;} + while ((*mdstat & 0x1f) != 0x03) {;} /* Probably an overkill... */ +} + +void dsp_on(void) +{ + int i; + + if (REG(PSC_PDSTAT1) & 0x1f) + return; /* Already on */ + + REG(PSC_GBLCTL) |= 0x01; + REG(PSC_PDCTL1) |= 0x01; + REG(PSC_PDCTL1) &= ~0x100; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) |= 0x03; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) &= 0xfffffeff; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) |= 0x03; + REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) &= 0xfffffeff; + REG(PSC_PTCMD) = 0x02; + + for (i = 0; i < 100; i++) { + if (REG(PSC_EPCPR) & 0x02) + break; + } + + REG(PSC_CHP_SHRTSW) = 0x01; + REG(PSC_PDCTL1) |= 0x100; + REG(PSC_EPCCR) = 0x02; + + for (i = 0; i < 100; i++) { + if (!(REG(PSC_PTSTAT) & 0x02)) + break; + } + + REG(PSC_GBLCTL) &= ~0x1f; +} + + +int board_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + + /* arch number of the board */ + gd->bd->bi_arch_number = MACH_TYPE_SONATA; + + /* address of boot parameters */ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + + /* Workaround for TMS320DM6446 errata 1.3.22 */ + REG(PSC_SILVER_BULLET) = 0; + + /* Power on required peripherals */ + lpsc_on(DAVINCI_LPSC_EMAC); + lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER); + lpsc_on(DAVINCI_LPSC_MDIO); + lpsc_on(DAVINCI_LPSC_I2C); + lpsc_on(DAVINCI_LPSC_UART0); + lpsc_on(DAVINCI_LPSC_TIMER1); + lpsc_on(DAVINCI_LPSC_GPIO); + + /* Powerup the DSP */ + dsp_on(); + + /* Bringup UART0 out of reset */ + REG(UART0_PWREMU_MGMT) = 0x0000e003; + + /* Enable GIO3.3V cells used for EMAC */ + REG(VDD3P3V_PWDN) = 0; + + /* Enable UART0 MUX lines */ + REG(PINMUX1) |= 1; + + /* Enable EMAC and AEMIF pins */ + REG(PINMUX0) = 0x80000c1f; + + /* Enable I2C pin Mux */ + REG(PINMUX1) |= (1 << 7); + + /* Set the Bus Priority Register to appropriate value */ + REG(VBPR) = 0x20; + + timer_init(); + + return(0); +} + +int misc_init_r (void) +{ + u_int8_t tmp[20], buf[10]; + int i = 0; + int clk = 0; + + + clk = ((REG(PLL2_PLLM) + 1) * 27) / ((REG(PLL2_DIV2) & 0x1f) + 1); + + printf ("ARM Clock : %dMHz\n", ((REG(PLL1_PLLM) + 1) * 27 ) / 2); + printf ("DDR Clock : %dMHz\n", (clk / 2)); + + /* Set Ethernet MAC address from EEPROM */ + if (i2c_read(CFG_I2C_EEPROM_ADDR, 0x7f00, CFG_I2C_EEPROM_ADDR_LEN, buf, 6)) { + printf("\nEEPROM @ 0x%02x read FAILED!!!\n", CFG_I2C_EEPROM_ADDR); + } else { + tmp[0] = 0xff; + for (i = 0; i < 6; i++) + tmp[0] &= buf[i]; + + if ((tmp[0] != 0xff) && (getenv("ethaddr") == NULL)) { + sprintf((char *)&tmp[0], "%02hhx:%02hhx:%02hhx:%02hhx:%02hhx:%02hhx", + buf[0], buf[1], buf[2], buf[3], buf[4], buf[5]); + setenv("ethaddr", (char *)&tmp[0]); + } + } + + if (!eth_hw_init()) { + printf("ethernet init failed!\n"); + } else { + printf("ETH PHY : %s\n", phy.name); + } + + return(0); +} + +int dram_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + + return(0); +} diff --git a/board/davinci/sonata/u-boot.lds b/board/davinci/sonata/u-boot.lds new file mode 100644 index 0000000000..710b2a2d6e --- /dev/null +++ b/board/davinci/sonata/u-boot.lds @@ -0,0 +1,52 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + . = ALIGN(4); + .text : + { + cpu/arm926ejs/start.o (.text) + *(.text) + } + . = ALIGN(4); + .rodata : { *(.rodata) } + . = ALIGN(4); + .data : { *(.data) } + . = ALIGN(4); + .got : { *(.got) } + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} -- cgit v1.2.3 From afaac86fe2948ac84cd9a12bbed883b3c683e7d9 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Sun, 12 Aug 2007 14:27:39 +0200 Subject: Clean up some remaining CFG_CMD_ -> CONFIG_CMD_ issues. Signed-off-by: Wolfgang Denk --- board/cm5200/cmd_cm5200.c | 4 ++-- board/pcs440ep/pcs440ep.c | 4 ++-- 2 files changed, 4 insertions(+), 4 deletions(-) (limited to 'board') diff --git a/board/cm5200/cmd_cm5200.c b/board/cm5200/cmd_cm5200.c index 5119a99ca2..fd9b914ae3 100644 --- a/board/cm5200/cmd_cm5200.c +++ b/board/cm5200/cmd_cm5200.c @@ -27,7 +27,7 @@ #include #include -#if (CONFIG_COMMANDS & CFG_CMD_BSP) +#ifdef CONFIG_CMD_BSB int do_i2c(char *argv[]) { @@ -445,4 +445,4 @@ U_BOOT_CMD( "fkt usb\n" " - Test USB communication\n" ); -#endif /* CFG_CMD_BSP */ +#endif /* CONFIG_CMD_BSP */ diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c index 696423eacb..e247fee0c1 100644 --- a/board/pcs440ep/pcs440ep.c +++ b/board/pcs440ep/pcs440ep.c @@ -879,7 +879,7 @@ int ide_preinit (void) } #endif -#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) +#if defined (CONFIG_CMD_IDE) && defined (CONFIG_IDE_RESET) void ide_set_reset (int idereset) { debug ("ide_reset(%d)\n", idereset); @@ -890,4 +890,4 @@ void ide_set_reset (int idereset) } udelay (10000); } -#endif /* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */ +#endif /* defined (CONFIG_CMD_IDE) && defined (CONFIG_IDE_RESET) */ -- cgit v1.2.3 From a4d2636f2a859245ed3a401f26189da2dfda4ceb Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Sun, 12 Aug 2007 15:11:38 +0200 Subject: Adapt board configuration and fix kernel crash on MCC200 board. The update procedure was modified to turn off the USB subsystem before exit for MCC200 and TRAB. This is necessary as otherwise the USB controller continues to write periodically to system memory! MCC200-specific notes: - the patch disables the magic key check for MCC200 - the patch contains the configuration changes made for the new revision of the board. Signed-off-by: Sergei Poselenov Signed-off-by: Wolfgang Denk --- board/mcc200/auto_update.c | 18 +++++++++++++----- board/trab/auto_update.c | 16 ++++++++++------ 2 files changed, 23 insertions(+), 11 deletions(-) (limited to 'board') diff --git a/board/mcc200/auto_update.c b/board/mcc200/auto_update.c index 6044565ff0..28e4c877b5 100644 --- a/board/mcc200/auto_update.c +++ b/board/mcc200/auto_update.c @@ -330,6 +330,8 @@ int do_auto_update(void) int i, res = 0, bitmap_first, cnt, old_ctrlc, got_ctrlc; char *env; long start, end; + +#if 0 /* disable key-press detection to speed up boot-up time */ uchar keypad_status1[2] = {0,0}, keypad_status2[2] = {0,0}; /* @@ -347,6 +349,7 @@ int do_auto_update(void) return 0; } +#endif au_usb_stor_curr_dev = -1; /* start USB */ if (usb_stop() < 0) { @@ -364,18 +367,21 @@ int do_auto_update(void) au_usb_stor_curr_dev = usb_stor_scan(0); if (au_usb_stor_curr_dev == -1) { debug ("No device found. Not initialized?\n"); - return -1; + res = -1; + goto xit; } /* check whether it has a partition table */ stor_dev = get_dev("usb", 0); if (stor_dev == NULL) { debug ("uknown device type\n"); - return -1; + res = -1; + goto xit; } if (fat_register_device(stor_dev, 1) != 0) { debug ("Unable to use USB %d:%d for fatls\n", au_usb_stor_curr_dev, 1); - return -1; + res = -1; + goto xit; } if (file_fat_detectfs() != 0) { debug ("file_fat_detectfs failed\n"); @@ -504,7 +510,7 @@ int do_auto_update(void) } while (res < 0); #endif } - usb_stop(); + /* restore the old state */ disable_ctrlc(old_ctrlc); #ifdef CONFIG_PROGRESSBAR @@ -517,6 +523,8 @@ int do_auto_update(void) lcd_enable(); } #endif - return 0; + xit: + usb_stop(); + return res; } #endif /* CONFIG_AUTO_UPDATE */ diff --git a/board/trab/auto_update.c b/board/trab/auto_update.c index 92120b0d01..54d3645ffa 100644 --- a/board/trab/auto_update.c +++ b/board/trab/auto_update.c @@ -450,7 +450,7 @@ do_auto_update(void) { block_dev_desc_t *stor_dev; long sz; - int i, res, bitmap_first, cnt, old_ctrlc, got_ctrlc; + int i, res = 0, bitmap_first, cnt, old_ctrlc, got_ctrlc; char *env; long start, end; @@ -477,18 +477,21 @@ do_auto_update(void) au_usb_stor_curr_dev = usb_stor_scan(0); if (au_usb_stor_curr_dev == -1) { debug ("No device found. Not initialized?\n"); - return -1; + res = -1; + goto xit; } /* check whether it has a partition table */ stor_dev = get_dev("usb", 0); if (stor_dev == NULL) { debug ("uknown device type\n"); - return -1; + res = -1; + goto xit; } if (fat_register_device(stor_dev, 1) != 0) { debug ("Unable to use USB %d:%d for fatls\n", au_usb_stor_curr_dev, 1); - return -1; + res = -1; + goto xit; } if (file_fat_detectfs() != 0) { debug ("file_fat_detectfs failed\n"); @@ -648,9 +651,10 @@ do_auto_update(void) /* enable the power switch */ *CPLD_VFD_BK &= ~POWER_OFF; } - usb_stop(); /* restore the old state */ disable_ctrlc(old_ctrlc); - return 0; +xit: + usb_stop(); + return res; } #endif /* CONFIG_AUTO_UPDATE */ -- cgit v1.2.3 From 6f6d7b9c8559e241e8d232621542b8b59699b07b Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Sun, 12 Aug 2007 18:28:18 +0200 Subject: Cleanup output on ADS5121 board Signed-off-by: Wolfgang Denk --- board/ads5121/ads5121.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'board') diff --git a/board/ads5121/ads5121.c b/board/ads5121/ads5121.c index c8bfdb8692..f275ce7de0 100644 --- a/board/ads5121/ads5121.c +++ b/board/ads5121/ads5121.c @@ -85,9 +85,7 @@ long int initdram (int board_type) { u32 msize = 0; - puts ("Initializing\n"); msize = fixed_sdram (); - puts (" DDR RAM: "); return msize; } -- cgit v1.2.3