1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
|
NAND FLASH commands and notes
See NOTE below!!!
# (C) Copyright 2003
# Dave Ellis, SIXNET, dge@sixnetio.com
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
Commands:
nand bad
Print a list of all of the bad blocks in the current device.
nand device
Print information about the current NAND device.
nand device num
Make device `num' the current device and print information about it.
nand erase off|partition size
nand erase clean [off|partition size]
Erase `size' bytes starting at offset `off'. Alternatively partition
name can be specified, in this case size will be eventually limited
to not exceed partition size (this behaviour applies also to read
and write commands). Only complete erase blocks can be erased.
If `erase' is specified without an offset or size, the entire flash
is erased. If `erase' is specified with partition but without an
size, the entire partition is erased.
If `clean' is specified, a JFFS2-style clean marker is written to
each block after it is erased.
This command will not erase blocks that are marked bad. There is
a debug option in cmd_nand.c to allow bad blocks to be erased.
Please read the warning there before using it, as blocks marked
bad by the manufacturer must _NEVER_ be erased.
nand info
Print information about all of the NAND devices found.
nand read addr ofs|partition size
Read `size' bytes from `ofs' in NAND flash to `addr'. Blocks that
are marked bad are skipped. If a page cannot be read because an
uncorrectable data error is found, the command stops with an error.
nand read.oob addr ofs|partition size
Read `size' bytes from the out-of-band data area corresponding to
`ofs' in NAND flash to `addr'. This is limited to the 16 bytes of
data for one 512-byte page or 2 256-byte pages. There is no check
for bad blocks or ECC errors.
nand write addr ofs|partition size
Write `size' bytes from `addr' to `ofs' in NAND flash. Blocks that
are marked bad are skipped. If a page cannot be read because an
uncorrectable data error is found, the command stops with an error.
As JFFS2 skips blocks similarly, this allows writing a JFFS2 image,
as long as the image is short enough to fit even after skipping the
bad blocks. Compact images, such as those produced by mkfs.jffs2
should work well, but loading an image copied from another flash is
going to be trouble if there are any bad blocks.
nand write.oob addr ofs|partition size
Write `size' bytes from `addr' to the out-of-band data area
corresponding to `ofs' in NAND flash. This is limited to the 16 bytes
of data for one 512-byte page or 2 256-byte pages. There is no check
for bad blocks.
Configuration Options:
CONFIG_CMD_NAND
Enables NAND support and commmands.
CONFIG_MTD_NAND_ECC_JFFS2
Define this if you want the Error Correction Code information in
the out-of-band data to be formatted to match the JFFS2 file system.
CONFIG_MTD_NAND_ECC_YAFFS would be another useful choice for
someone to implement.
CFG_MAX_NAND_DEVICE
The maximum number of NAND devices you want to support.
NAND Interface:
#define NAND_WAIT_READY(nand)
Wait until the NAND flash is ready. Typically this would be a
loop waiting for the READY/BUSY line from the flash to indicate it
it is ready.
#define WRITE_NAND_COMMAND(d, adr)
Write the command byte `d' to the flash at `adr' with the
CLE (command latch enable) line true. If your board uses writes to
different addresses to control CLE and ALE, you can modify `adr'
to be the appropriate address here. If your board uses I/O registers
to control them, it is probably better to let NAND_CTL_SETCLE()
and company do it.
#define WRITE_NAND_ADDRESS(d, adr)
Write the address byte `d' to the flash at `adr' with the
ALE (address latch enable) line true. If your board uses writes to
different addresses to control CLE and ALE, you can modify `adr'
to be the appropriate address here. If your board uses I/O registers
to control them, it is probably better to let NAND_CTL_SETALE()
and company do it.
#define WRITE_NAND(d, adr)
Write the data byte `d' to the flash at `adr' with the
ALE and CLE lines false. If your board uses writes to
different addresses to control CLE and ALE, you can modify `adr'
to be the appropriate address here. If your board uses I/O registers
to control them, it is probably better to let NAND_CTL_CLRALE()
and company do it.
#define READ_NAND(adr)
Read a data byte from the flash at `adr' with the
ALE and CLE lines false. If your board uses reads from
different addresses to control CLE and ALE, you can modify `adr'
to be the appropriate address here. If your board uses I/O registers
to control them, it is probably better to let NAND_CTL_CLRALE()
and company do it.
#define NAND_DISABLE_CE(nand)
Set CE (Chip Enable) low to enable the NAND flash.
#define NAND_ENABLE_CE(nand)
Set CE (Chip Enable) high to disable the NAND flash.
#define NAND_CTL_CLRALE(nandptr)
Set ALE (address latch enable) low. If ALE control is handled by
WRITE_NAND_ADDRESS() this can be empty.
#define NAND_CTL_SETALE(nandptr)
Set ALE (address latch enable) high. If ALE control is handled by
WRITE_NAND_ADDRESS() this can be empty.
#define NAND_CTL_CLRCLE(nandptr)
Set CLE (command latch enable) low. If CLE control is handled by
WRITE_NAND_ADDRESS() this can be empty.
#define NAND_CTL_SETCLE(nandptr)
Set CLE (command latch enable) high. If CLE control is handled by
WRITE_NAND_ADDRESS() this can be empty.
More Definitions:
These definitions are needed in the board configuration for now, but
may really belong in a header file.
TODO: Figure which ones are truly configuration settings and rename
them to CFG_NAND_... and move the rest somewhere appropriate.
#define SECTORSIZE 512
#define ADDR_COLUMN 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define CFG_DAVINCI_BROKEN_ECC
Versions of U-Boot <= 1.3.3 and Montavista Linux kernels
generated bogus ECCs on large-page NAND. Both large and small page
NAND ECCs were incompatible with the Linux davinci git tree (since
NAND was integrated in 2.6.24).
Turn this ON if you want backwards compatibility.
Turn this OFF if you want U-Boot and the Linux davinci git kernel
to use the same ECC format.
NOTE:
=====
We now use a complete rewrite of the NAND code based on what is in
2.6.12 Linux kernel.
The old NAND handling code has been re-factored and is now confined
to only board-specific files and - unfortunately - to the DoC code
(see below). A new configuration variable has been introduced:
CONFIG_NAND_LEGACY, which has to be defined in the board config file if
that board uses legacy code.
The necessary changes have been made to all affected boards, and no
build breakage has been introduced, except for NETTA and NETTA_ISDN
targets from MAKEALL. This is due to the fact that these two boards
use JFFS, which has been adopted to use the new NAND, and at the same
time use NAND in legacy mode. The breakage will disappear when the
board-specific code is changed to the new NAND.
As mentioned above, the legacy code is still used by the DoC subsystem.
The consequence of this is that the legacy NAND can't be removed from
the tree until the DoC is ported to use the new NAND support (or boards
with DoC will break).
Additional improvements to the NAND subsystem by Guido Classen, 10-10-2006
JFFS2 related commands:
implement "nand erase clean" and old "nand erase"
using both the new code which is able to skip bad blocks
"nand erase clean" additionally writes JFFS2-cleanmarkers in the oob.
Miscellaneous and testing commands:
"markbad [offset]"
create an artificial bad block (for testing bad block handling)
"scrub [offset length]"
like "erase" but don't skip bad block. Instead erase them.
DANGEROUS!!! Factory set bad blocks will be lost. Use only
to remove artificial bad blocks created with the "markbad" command.
NAND locking command (for chips with active LOCKPRE pin)
"nand lock"
set NAND chip to lock state (all pages locked)
"nand lock tight"
set NAND chip to lock tight state (software can't change locking anymore)
"nand lock status"
displays current locking status of all pages
"nand unlock [offset] [size]"
unlock consecutive area (can be called multiple times for different areas)
I have tested the code with board containing 128MiB NAND large page chips
and 32MiB small page chips.
|
