blob: 66b723d14e9070a66e30032b1af45a78775e07ec (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
|
/*
* Copyright (C) 2014-2015 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _CONFIG_DB_MV7846MP_GP_H
#define _CONFIG_DB_MV7846MP_GP_H
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_DB_784MP_GP /* Board target name for DDR training */
#define CONFIG_DISPLAY_BOARDINFO_LATE
/*
* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
* for DDR ECC byte filling in the SPL before loading the main
* U-Boot into it.
*/
#define CONFIG_SYS_TEXT_BASE 0x00800000
#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
/*
* Commands configuration
*/
#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_ENV
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_EXT4
#define CONFIG_CMD_FAT
#define CONFIG_CMD_FS_GENERIC
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SATA
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_SPEED 100000
/* USB/EHCI configuration */
#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
/* SPI NOR flash default params, used by sf commands */
#define CONFIG_SF_DEFAULT_SPEED 1000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
/* Environment in SPI NOR flash */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */
#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */
#define CONFIG_PHY_MARVELL /* there is a marvell phy */
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */
#define CONFIG_SYS_ALT_MEMTEST
/* SATA support */
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA_MV
#define CONFIG_LIBATA
#define CONFIG_LBA48
#define CONFIG_EFI_PARTITION
#define CONFIG_DOS_PARTITION
/* Additional FS support/configuration */
#define CONFIG_SUPPORT_VFAT
/* PCIe support */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_PCI
#define CONFIG_PCI_MVEBU
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#endif
/* NAND */
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_ONFI_DETECTION
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
/*
* Memory layout while starting into the bin_hdr via the
* BootROM:
*
* 0x4000.4000 - 0x4003.4000 headers space (192KiB)
* 0x4000.4030 bin_hdr start address
* 0x4003.4000 - 0x4004.7c00 BootROM memory allocations (15KiB)
* 0x4007.fffc BootROM stack top
*
* The address space between 0x4007.fffc and 0x400f.fff is not locked in
* L2 cache thus cannot be used.
*/
/* SPL */
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x40004030
#define CONFIG_SPL_MAX_SIZE ((128 << 10) - 0x4030)
#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))
#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
/* SPL related SPI defines */
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_BUS 0
#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
#define CONFIG_SPD_EEPROM 0x4e
#define CONFIG_BOARD_ECC_SUPPORT /* this board supports ECC */
#endif /* _CONFIG_DB_MV7846MP_GP_H */
|
