drivers/net: delete old DEC depca ISA drivers support.

These are old ISA 10Mbit cards from the 1st 1/2 of the 1990s and
required manual jumper settings in order to configure them.  Here
we remove them on the premise that they are no longer used in any
modern 3.9+ kernels.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

6 files changed, 0 insertions, 2201 deletions

diff --git a/Documentation/networking/00-INDEX b/Documentation/networking/00-INDEX
index 1abfff26f8a0..6ec1d6f368af 100644
--- a/Documentation/networking/00-INDEX
+++ b/Documentation/networking/00-INDEX
@@ -52,8 +52,6 @@ de4x5.txt
 	- the Digital EtherWORKS DE4?? and DE5?? PCI Ethernet driver
 decnet.txt
 	- info on using the DECnet networking layer in Linux.
-depca.txt
-	- the Digital DEPCA/EtherWORKS DE1?? and DE2?? LANCE Ethernet driver
 dl2k.txt
 	- README for D-Link DL2000-based Gigabit Ethernet Adapters (dl2k.ko).
 dm9000.txt
diff --git a/Documentation/networking/depca.txt b/Documentation/networking/depca.txt
deleted file mode 100644
index 24c6b26e5658..000000000000
--- a/Documentation/networking/depca.txt
+++ /dev/null
@@ -1,92 +0,0 @@
-
-DE10x
-=====
-
-Memory Addresses:
-
-	SW1	SW2	SW3	SW4
-64K	on	on	on	on	d0000	dbfff
-	off	on	on	on	c0000	cbfff
-	off	off	on	on	e0000	ebfff
-
-32K	on	on	off	on	d8000	dbfff
-	off	on	off	on	c8000	cbfff
-	off	off	off	on	e8000	ebfff
-
-DBR ROM	on	on			dc000	dffff
-	off	on			cc000	cffff
-	off	off			ec000	effff
-
-Note  that the 2K  mode   is set  by   SW3/SW4  on/off or  off/off.  Address
-assignment is through the RBSA register.
-
-I/O Address:
-	SW5
-0x300	on
-0x200	off
-
-Remote Boot:
-	SW6
-Disable	on
-Enable	off
-
-Remote Boot Timeout:
-	SW7
-2.5min	on
-30s	off
-
-IRQ:
-	SW8	SW9	SW10	SW11	SW12
-2	on	off	off	off	off
-3	off	on	off	off	off
-4	off	off	on	off	off
-5	off	off	off	on	off
-7	off	off	off	off	on
-
-DE20x
-=====
-
-Memory Size:
-
-	SW3	SW4
-64K	on	on
-32K	off	on
-2K	on 	off
-2K	off	off
-
-Start Addresses:
-
-	SW1	SW2	SW3	SW4
-64K	on	on	on	on	c0000	cffff
-	on	off	on	on	d0000	dffff
-	off	on	on	on	e0000	effff
-
-32K	on	on	off	off	c8000	cffff
-	on	off	off	off	d8000	dffff
-	off	on	off	off	e8000	effff
-
-Illegal	off	off	 -	 -	  -	  -
-
-I/O Address:
-	SW5
-0x300	on
-0x200	off
-
-Remote Boot:
-	SW6
-Disable	on
-Enable	off
-
-Remote Boot Timeout:
-	SW7
-2.5min	on
-30s	off
-
-IRQ:
-	SW8	SW9	SW10	SW11	SW12
-5	on	off	off	off	off
-9	off	on	off	off	off
-10	off	off	on	off	off
-11	off	off	off	on	off
-15	off	off	off	off	on
-
diff --git a/drivers/net/ethernet/amd/Kconfig b/drivers/net/ethernet/amd/Kconfig
index 304613302f01..13d74aa4033d 100644
--- a/drivers/net/ethernet/amd/Kconfig
+++ b/drivers/net/ethernet/amd/Kconfig
@@ -105,19 +105,6 @@ config DECLANCE
 	  DEC (now Compaq) based on the AMD LANCE chipset, including the
 	  DEPCA series.  (This chipset is better known via the NE2100 cards.)
 
-config DEPCA
-	tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
-	depends on (ISA || EISA)
-	select CRC32
-	---help---
-	  If you have a network (Ethernet) card of this type, say Y and read
-	  the Ethernet-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto> as well as
-	  <file:drivers/net/ethernet/amd/depca.c>.
-
-	  To compile this driver as a module, choose M here. The module
-	  will be called depca.
-
 config HPLANCE
 	bool "HP on-board LANCE support"
 	depends on DIO
diff --git a/drivers/net/ethernet/amd/Makefile b/drivers/net/ethernet/amd/Makefile
index 175caa5328c9..cdd4301a973d 100644
--- a/drivers/net/ethernet/amd/Makefile
+++ b/drivers/net/ethernet/amd/Makefile
@@ -8,7 +8,6 @@ obj-$(CONFIG_ARM_AM79C961A) += am79c961a.o
 obj-$(CONFIG_ARIADNE) += ariadne.o
 obj-$(CONFIG_ATARILANCE) += atarilance.o
 obj-$(CONFIG_DECLANCE) += declance.o
-obj-$(CONFIG_DEPCA) += depca.o
 obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
 obj-$(CONFIG_LANCE) += lance.o
 obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
diff --git a/drivers/net/ethernet/amd/depca.c b/drivers/net/ethernet/amd/depca.c
deleted file mode 100644
index 34a485363d5b..000000000000
--- a/drivers/net/ethernet/amd/depca.c
+++ /dev/null
@@ -1,1910 +0,0 @@
-/*  depca.c: A DIGITAL DEPCA & EtherWORKS ethernet driver for linux.
-
-    Written 1994, 1995 by David C. Davies.
-
-
-                      Copyright 1994 David C. Davies
-		                   and
-			 United States Government
-	 (as represented by the Director, National Security Agency).
-
-               Copyright 1995  Digital Equipment Corporation.
-
-
-    This software may be used and distributed according to the terms of
-    the GNU General Public License, incorporated herein by reference.
-
-    This driver is written for the Digital Equipment Corporation series
-    of DEPCA and EtherWORKS ethernet cards:
-
-        DEPCA       (the original)
-    	DE100
-    	DE101
-	DE200 Turbo
-	DE201 Turbo
-	DE202 Turbo (TP BNC)
-	DE210
-	DE422       (EISA)
-
-    The  driver has been tested on DE100, DE200 and DE202 cards  in  a
-    relatively busy network. The DE422 has been tested a little.
-
-    This  driver will NOT work   for the DE203,  DE204  and DE205 series  of
-    cards,  since they have  a  new custom ASIC in   place of the AMD  LANCE
-    chip.  See the 'ewrk3.c'   driver in the  Linux  source tree for running
-    those cards.
-
-    I have benchmarked the driver with a  DE100 at 595kB/s to (542kB/s from)
-    a DECstation 5000/200.
-
-    The author may be reached at davies@maniac.ultranet.com
-
-    =========================================================================
-
-    The  driver was originally based  on   the 'lance.c' driver from  Donald
-    Becker   which  is included with  the  standard  driver distribution for
-    linux.  V0.4  is  a complete  re-write  with only  the kernel  interface
-    remaining from the original code.
-
-    1) Lance.c code in /linux/drivers/net/
-    2) "Ethernet/IEEE 802.3 Family. 1992 World Network Data Book/Handbook",
-       AMD, 1992 [(800) 222-9323].
-    3) "Am79C90 CMOS Local Area Network Controller for Ethernet (C-LANCE)",
-       AMD, Pub. #17881, May 1993.
-    4) "Am79C960 PCnet-ISA(tm), Single-Chip Ethernet Controller for ISA",
-       AMD, Pub. #16907, May 1992
-    5) "DEC EtherWORKS LC Ethernet Controller Owners Manual",
-       Digital Equipment corporation, 1990, Pub. #EK-DE100-OM.003
-    6) "DEC EtherWORKS Turbo Ethernet Controller Owners Manual",
-       Digital Equipment corporation, 1990, Pub. #EK-DE200-OM.003
-    7) "DEPCA Hardware Reference Manual", Pub. #EK-DEPCA-PR
-       Digital Equipment Corporation, 1989
-    8) "DEC EtherWORKS Turbo_(TP BNC) Ethernet Controller Owners Manual",
-       Digital Equipment corporation, 1991, Pub. #EK-DE202-OM.001
-
-
-    Peter Bauer's depca.c (V0.5) was referred to when debugging V0.1 of this
-    driver.
-
-    The original DEPCA  card requires that the  ethernet ROM address counter
-    be enabled to count and has an 8 bit NICSR.  The ROM counter enabling is
-    only  done when a  0x08 is read as the  first address octet (to minimise
-    the chances  of writing over some  other hardware's  I/O register).  The
-    NICSR accesses   have been changed  to  byte accesses  for all the cards
-    supported by this driver, since there is only one  useful bit in the MSB
-    (remote boot timeout) and it  is not used.  Also, there  is a maximum of
-    only 48kB network  RAM for this  card.  My thanks  to Torbjorn Lindh for
-    help debugging all this (and holding my feet to  the fire until I got it
-    right).
-
-    The DE200  series  boards have  on-board 64kB  RAM for  use  as a shared
-    memory network  buffer. Only the DE100  cards make use  of a  2kB buffer
-    mode which has not  been implemented in  this driver (only the 32kB  and
-    64kB modes are supported [16kB/48kB for the original DEPCA]).
-
-    At the most only 2 DEPCA cards can  be supported on  the ISA bus because
-    there is only provision  for two I/O base addresses  on each card (0x300
-    and 0x200). The I/O address is detected by searching for a byte sequence
-    in the Ethernet station address PROM at the expected I/O address for the
-    Ethernet  PROM.   The shared memory  base   address  is 'autoprobed'  by
-    looking  for the self  test PROM  and detecting the  card name.   When a
-    second  DEPCA is  detected,  information  is   placed in the   base_addr
-    variable of the  next device structure (which  is created if necessary),
-    thus  enabling ethif_probe  initialization  for the device.  More than 2
-    EISA cards can  be  supported, but  care will  be  needed assigning  the
-    shared memory to ensure that each slot has the  correct IRQ, I/O address
-    and shared memory address assigned.
-
-    ************************************************************************
-
-    NOTE: If you are using two  ISA DEPCAs, it is  important that you assign
-    the base memory addresses correctly.   The  driver autoprobes I/O  0x300
-    then 0x200.  The  base memory address for  the first device must be less
-    than that of the second so that the auto probe will correctly assign the
-    I/O and memory addresses on the same card.  I can't think of a way to do
-    this unambiguously at the moment, since there is nothing on the cards to
-    tie I/O and memory information together.
-
-    I am unable  to  test  2 cards   together for now,    so this  code   is
-    unchecked. All reports, good or bad, are welcome.
-
-    ************************************************************************
-
-    The board IRQ   setting must be  at an  unused IRQ which  is auto-probed
-    using Donald Becker's autoprobe routines. DEPCA and DE100 board IRQs are
-    {2,3,4,5,7}, whereas the  DE200 is at {5,9,10,11,15}.  Note that IRQ2 is
-    really IRQ9 in machines with 16 IRQ lines.
-
-    No 16MB memory  limitation should exist with this  driver as DMA is  not
-    used and the common memory area is in low memory on the network card (my
-    current system has 20MB and I've not had problems yet).
-
-    The ability to load this driver as a loadable module has been added. To
-    utilise this ability, you have to do <8 things:
-
-    0) have a copy of the loadable modules code installed on your system.
-    1) copy depca.c from the  /linux/drivers/net directory to your favourite
-    temporary directory.
-    2) if you wish, edit the  source code near  line 1530 to reflect the I/O
-    address and IRQ you're using (see also 5).
-    3) compile  depca.c, but include -DMODULE in  the command line to ensure
-    that the correct bits are compiled (see end of source code).
-    4) if you are wanting to add a new  card, goto 5. Otherwise, recompile a
-    kernel with the depca configuration turned off and reboot.
-    5) insmod depca.o [irq=7] [io=0x200] [mem=0xd0000] [adapter_name=DE100]
-       [Alan Cox: Changed the code to allow command line irq/io assignments]
-       [Dave Davies: Changed the code to allow command line mem/name
-                                                                assignments]
-    6) run the net startup bits for your eth?? interface manually
-    (usually /etc/rc.inet[12] at boot time).
-    7) enjoy!
-
-    Note that autoprobing is not allowed in loadable modules - the system is
-    already up and running and you're messing with interrupts.
-
-    To unload a module, turn off the associated interface
-    'ifconfig eth?? down' then 'rmmod depca'.
-
-    To assign a base memory address for the shared memory  when running as a
-    loadable module, see 5 above.  To include the adapter  name (if you have
-    no PROM  but know the card name)  also see 5  above. Note that this last
-    option  will not work  with kernel  built-in  depca's.
-
-    The shared memory assignment for a loadable module  makes sense to avoid
-    the 'memory autoprobe' picking the wrong shared memory  (for the case of
-    2 depca's in a PC).
-
-    ************************************************************************
-    Support for MCA EtherWORKS cards added 11-3-98. (MCA since deleted)
-    Verified to work with up to 2 DE212 cards in a system (although not
-      fully stress-tested).
-
-    Revision History
-    ----------------
-
-    Version   Date        Description
-
-      0.1     25-jan-94   Initial writing.
-      0.2     27-jan-94   Added LANCE TX hardware buffer chaining.
-      0.3      1-feb-94   Added multiple DEPCA support.
-      0.31     4-feb-94   Added DE202 recognition.
-      0.32    19-feb-94   Tidy up. Improve multi-DEPCA support.
-      0.33    25-feb-94   Fix DEPCA ethernet ROM counter enable.
-                          Add jabber packet fix from murf@perftech.com
-			  and becker@super.org
-      0.34     7-mar-94   Fix DEPCA max network memory RAM & NICSR access.
-      0.35     8-mar-94   Added DE201 recognition. Tidied up.
-      0.351   30-apr-94   Added EISA support. Added DE422 recognition.
-      0.36    16-may-94   DE422 fix released.
-      0.37    22-jul-94   Added MODULE support
-      0.38    15-aug-94   Added DBR ROM switch in depca_close().
-                          Multi DEPCA bug fix.
-      0.38axp 15-sep-94   Special version for Alpha AXP Linux V1.0.
-      0.381   12-dec-94   Added DE101 recognition, fix multicast bug.
-      0.382    9-feb-95   Fix recognition bug reported by <bkm@star.rl.ac.uk>.
-      0.383   22-feb-95   Fix for conflict with VESA SCSI reported by
-                          <stromain@alf.dec.com>
-      0.384   17-mar-95   Fix a ring full bug reported by <bkm@star.rl.ac.uk>
-      0.385    3-apr-95   Fix a recognition bug reported by
-                                                <ryan.niemi@lastfrontier.com>
-      0.386   21-apr-95   Fix the last fix...sorry, must be galloping senility
-      0.40    25-May-95   Rewrite for portability & updated.
-                          ALPHA support from <jestabro@amt.tay1.dec.com>
-      0.41    26-Jun-95   Added verify_area() calls in depca_ioctl() from
-                          suggestion by <heiko@colossus.escape.de>
-      0.42    27-Dec-95   Add 'mem' shared memory assignment for loadable
-                          modules.
-                          Add 'adapter_name' for loadable modules when no PROM.
-			  Both above from a suggestion by
-			  <pchen@woodruffs121.residence.gatech.edu>.
-			  Add new multicasting code.
-      0.421   22-Apr-96	  Fix alloc_device() bug <jari@markkus2.fimr.fi>
-      0.422   29-Apr-96	  Fix depca_hw_init() bug <jari@markkus2.fimr.fi>
-      0.423    7-Jun-96   Fix module load bug <kmg@barco.be>
-      0.43    16-Aug-96   Update alloc_device() to conform to de4x5.c
-      0.44     1-Sep-97   Fix *_probe() to test check_region() first - bug
-                           reported by <mmogilvi@elbert.uccs.edu>
-      0.45     3-Nov-98   Added support for MCA EtherWORKS (DE210/DE212) cards
-                           by <tymm@computer.org>
-      0.451    5-Nov-98   Fixed mca stuff cuz I'm a dummy. <tymm@computer.org>
-      0.5     14-Nov-98   Re-spin for 2.1.x kernels.
-      0.51    27-Jun-99   Correct received packet length for CRC from
-                           report by <worm@dkik.dk>
-      0.52    16-Oct-00   Fixes for 2.3 io memory accesses
-                          Fix show-stopper (ints left masked) in depca_interrupt
-			   by <peterd@pnd-pc.demon.co.uk>
-      0.53    12-Jan-01	  Release resources on failure, bss tidbits
-      			   by acme@conectiva.com.br
-      0.54    08-Nov-01	  use library crc32 functions
-      			   by Matt_Domsch@dell.com
-      0.55    01-Mar-03   Use EISA/sysfs framework <maz@wild-wind.fr.eu.org>
-
-    =========================================================================
-*/
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/crc32.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/time.h>
-#include <linux/types.h>
-#include <linux/unistd.h>
-#include <linux/ctype.h>
-#include <linux/moduleparam.h>
-#include <linux/platform_device.h>
-#include <linux/bitops.h>
-
-#include <asm/uaccess.h>
-#include <asm/io.h>
-#include <asm/dma.h>
-
-#ifdef CONFIG_EISA
-#include <linux/eisa.h>
-#endif
-
-#include "depca.h"
-
-static char version[] __initdata = "depca.c:v0.53 2001/1/12 davies@maniac.ultranet.com\n";
-
-#ifdef DEPCA_DEBUG
-static int depca_debug = DEPCA_DEBUG;
-#else
-static int depca_debug = 1;
-#endif
-
-#define DEPCA_NDA 0xffe0	/* No Device Address */
-
-#define TX_TIMEOUT (1*HZ)
-
-/*
-** Ethernet PROM defines
-*/
-#define PROBE_LENGTH    32
-#define ETH_PROM_SIG    0xAA5500FFUL
-
-/*
-** Set the number of Tx and Rx buffers. Ensure that the memory requested
-** here is <= to the amount of shared memory set up by the board switches.
-** The number of descriptors MUST BE A POWER OF 2.
-**
-** total_memory = NUM_RX_DESC*(8+RX_BUFF_SZ) + NUM_TX_DESC*(8+TX_BUFF_SZ)
-*/
-#define NUM_RX_DESC     8	/* Number of RX descriptors */
-#define NUM_TX_DESC     8	/* Number of TX descriptors */
-#define RX_BUFF_SZ	1536	/* Buffer size for each Rx buffer */
-#define TX_BUFF_SZ	1536	/* Buffer size for each Tx buffer */
-
-/*
-** EISA bus defines
-*/
-#define DEPCA_EISA_IO_PORTS 0x0c00	/* I/O port base address, slot 0 */
-
-/*
-** ISA Bus defines
-*/
-#define DEPCA_RAM_BASE_ADDRESSES {0xc0000,0xd0000,0xe0000,0x00000}
-#define DEPCA_TOTAL_SIZE 0x10
-
-static struct {
-	u_long iobase;
-	struct platform_device *device;
-} depca_io_ports[] = {
-	{ 0x300, NULL },
-	{ 0x200, NULL },
-	{ 0    , NULL },
-};
-
-/*
-** Name <-> Adapter mapping
-*/
-#define DEPCA_SIGNATURE {"DEPCA",\
-			 "DE100","DE101",\
-                         "DE200","DE201","DE202",\
-			 "DE210","DE212",\
-                         "DE422",\
-                         ""}
-
-static char* __initdata depca_signature[] = DEPCA_SIGNATURE;
-
-enum depca_type {
-	DEPCA, de100, de101, de200, de201, de202, de210, de212, de422, unknown
-};
-
-static char depca_string[] = "depca";
-
-static int depca_device_remove (struct device *device);
-
-#ifdef CONFIG_EISA
-static struct eisa_device_id depca_eisa_ids[] = {
-	{ "DEC4220", de422 },
-	{ "" }
-};
-MODULE_DEVICE_TABLE(eisa, depca_eisa_ids);
-
-static int depca_eisa_probe  (struct device *device);
-
-static struct eisa_driver depca_eisa_driver = {
-	.id_table = depca_eisa_ids,
-	.driver   = {
-		.name    = depca_string,
-		.probe   = depca_eisa_probe,
-		.remove  = depca_device_remove
-	}
-};
-#endif
-
-static int depca_isa_probe (struct platform_device *);
-
-static int depca_isa_remove(struct platform_device *pdev)
-{
-	return depca_device_remove(&pdev->dev);
-}
-
-static struct platform_driver depca_isa_driver = {
-	.probe  = depca_isa_probe,
-	.remove = depca_isa_remove,
-	.driver	= {
-		.name   = depca_string,
-	},
-};
-
-/*
-** Miscellaneous info...
-*/
-#define DEPCA_STRLEN 16
-
-/*
-** Memory Alignment. Each descriptor is 4 longwords long. To force a
-** particular alignment on the TX descriptor, adjust DESC_SKIP_LEN and
-** DESC_ALIGN. DEPCA_ALIGN aligns the start address of the private memory area
-** and hence the RX descriptor ring's first entry.
-*/
-#define DEPCA_ALIGN4      ((u_long)4 - 1)	/* 1 longword align */
-#define DEPCA_ALIGN8      ((u_long)8 - 1)	/* 2 longword (quadword) align */
-#define DEPCA_ALIGN         DEPCA_ALIGN8	/* Keep the LANCE happy... */
-
-/*
-** The DEPCA Rx and Tx ring descriptors.
-*/
-struct depca_rx_desc {
-	volatile s32 base;
-	s16 buf_length;		/* This length is negative 2's complement! */
-	s16 msg_length;		/* This length is "normal". */
-};
-
-struct depca_tx_desc {
-	volatile s32 base;
-	s16 length;		/* This length is negative 2's complement! */
-	s16 misc;		/* Errors and TDR info */
-};
-
-#define LA_MASK 0x0000ffff	/* LANCE address mask for mapping network RAM
-				   to LANCE memory address space */
-
-/*
-** The Lance initialization block, described in databook, in common memory.
-*/
-struct depca_init {
-	u16 mode;		/* Mode register */
-	u8 phys_addr[ETH_ALEN];	/* Physical ethernet address */
-	u8 mcast_table[8];	/* Multicast Hash Table. */
-	u32 rx_ring;		/* Rx ring base pointer & ring length */
-	u32 tx_ring;		/* Tx ring base pointer & ring length */
-};
-
-#define DEPCA_PKT_STAT_SZ 16
-#define DEPCA_PKT_BIN_SZ  128	/* Should be >=100 unless you
-				   increase DEPCA_PKT_STAT_SZ */
-struct depca_private {
-	char adapter_name[DEPCA_STRLEN];	/* /proc/ioports string                  */
-	enum depca_type adapter;		/* Adapter type */
-	enum {
-                DEPCA_BUS_ISA = 1,
-                DEPCA_BUS_EISA,
-        } depca_bus;	        /* type of bus */
-	struct depca_init init_block;	/* Shadow Initialization block            */
-/* CPU address space fields */
-	struct depca_rx_desc __iomem *rx_ring;	/* Pointer to start of RX descriptor ring */
-	struct depca_tx_desc __iomem *tx_ring;	/* Pointer to start of TX descriptor ring */
-	void __iomem *rx_buff[NUM_RX_DESC];	/* CPU virt address of sh'd memory buffs  */
-	void __iomem *tx_buff[NUM_TX_DESC];	/* CPU virt address of sh'd memory buffs  */
-	void __iomem *sh_mem;	/* CPU mapped virt address of device RAM  */
-	u_long mem_start;	/* Bus address of device RAM (before remap) */
-	u_long mem_len;		/* device memory size */
-/* Device address space fields */
-	u_long device_ram_start;	/* Start of RAM in device addr space      */
-/* Offsets used in both address spaces */
-	u_long rx_ring_offset;	/* Offset from start of RAM to rx_ring    */
-	u_long tx_ring_offset;	/* Offset from start of RAM to tx_ring    */
-	u_long buffs_offset;	/* LANCE Rx and Tx buffers start address. */
-/* Kernel-only (not device) fields */
-	int rx_new, tx_new;	/* The next free ring entry               */
-	int rx_old, tx_old;	/* The ring entries to be free()ed.       */
-	spinlock_t lock;
-	struct {		/* Private stats counters                 */
-		u32 bins[DEPCA_PKT_STAT_SZ];
-		u32 unicast;
-		u32 multicast;
-		u32 broadcast;
-		u32 excessive_collisions;
-		u32 tx_underruns;
-		u32 excessive_underruns;
-	} pktStats;
-	int txRingMask;		/* TX ring mask                           */
-	int rxRingMask;		/* RX ring mask                           */
-	s32 rx_rlen;		/* log2(rxRingMask+1) for the descriptors */
-	s32 tx_rlen;		/* log2(txRingMask+1) for the descriptors */
-};
-
-/*
-** The transmit ring full condition is described by the tx_old and tx_new
-** pointers by:
-**    tx_old            = tx_new    Empty ring
-**    tx_old            = tx_new+1  Full ring
-**    tx_old+txRingMask = tx_new    Full ring  (wrapped condition)
-*/
-#define TX_BUFFS_AVAIL ((lp->tx_old<=lp->tx_new)?\
-			 lp->tx_old+lp->txRingMask-lp->tx_new:\
-                         lp->tx_old               -lp->tx_new-1)
-
-/*
-** Public Functions
-*/
-static int depca_open(struct net_device *dev);
-static netdev_tx_t depca_start_xmit(struct sk_buff *skb,
-				    struct net_device *dev);
-static irqreturn_t depca_interrupt(int irq, void *dev_id);
-static int depca_close(struct net_device *dev);
-static int depca_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
-static void depca_tx_timeout(struct net_device *dev);
-static void set_multicast_list(struct net_device *dev);
-
-/*
-** Private functions
-*/
-static void depca_init_ring(struct net_device *dev);
-static int depca_rx(struct net_device *dev);
-static int depca_tx(struct net_device *dev);
-
-static void LoadCSRs(struct net_device *dev);
-static int InitRestartDepca(struct net_device *dev);
-static int DepcaSignature(char *name, u_long paddr);
-static int DevicePresent(u_long ioaddr);
-static int get_hw_addr(struct net_device *dev);
-static void SetMulticastFilter(struct net_device *dev);
-static int load_packet(struct net_device *dev, struct sk_buff *skb);
-static void depca_dbg_open(struct net_device *dev);
-
-static u_char de1xx_irq[] __initdata = { 2, 3, 4, 5, 7, 9, 0 };
-static u_char de2xx_irq[] __initdata = { 5, 9, 10, 11, 15, 0 };
-static u_char de422_irq[] __initdata = { 5, 9, 10, 11, 0 };
-static u_char *depca_irq;
-
-static int irq;
-static int io;
-static char *adapter_name;
-static int mem;			/* For loadable module assignment
-				   use insmod mem=0x????? .... */
-module_param (irq, int, 0);
-module_param (io, int, 0);
-module_param (adapter_name, charp, 0);
-module_param (mem, int, 0);
-MODULE_PARM_DESC(irq, "DEPCA IRQ number");
-MODULE_PARM_DESC(io, "DEPCA I/O base address");
-MODULE_PARM_DESC(adapter_name, "DEPCA adapter name");
-MODULE_PARM_DESC(mem, "DEPCA shared memory address");
-MODULE_LICENSE("GPL");
-
-/*
-** Miscellaneous defines...
-*/
-#define STOP_DEPCA \
-    outw(CSR0, DEPCA_ADDR);\
-    outw(STOP, DEPCA_DATA)
-
-static const struct net_device_ops depca_netdev_ops = {
-	.ndo_open 		= depca_open,
-	.ndo_start_xmit 	= depca_start_xmit,
-	.ndo_stop 		= depca_close,
-	.ndo_set_rx_mode	= set_multicast_list,
-	.ndo_do_ioctl 		= depca_ioctl,
-	.ndo_tx_timeout 	= depca_tx_timeout,
-	.ndo_change_mtu		= eth_change_mtu,
-	.ndo_set_mac_address 	= eth_mac_addr,
-	.ndo_validate_addr	= eth_validate_addr,
-};
-
-static int __init depca_hw_init (struct net_device *dev, struct device *device)
-{
-	struct depca_private *lp;
-	int i, j, offset, netRAM, mem_len, status = 0;
-	s16 nicsr;
-	u_long ioaddr;
-	u_long mem_start;
-
-	/*
-	 * We are now supposed to enter this function with the
-	 * following fields filled with proper values :
-	 *
-	 * dev->base_addr
-	 * lp->mem_start
-	 * lp->depca_bus
-	 * lp->adapter
-	 *
-	 * dev->irq can be set if known from device configuration (on
-	 * MCA or EISA) or module option. Otherwise, it will be auto
-	 * detected.
-	 */
-
-	ioaddr = dev->base_addr;
-
-	STOP_DEPCA;
-
-	nicsr = inb(DEPCA_NICSR);
-	nicsr = ((nicsr & ~SHE & ~RBE & ~IEN) | IM);
-	outb(nicsr, DEPCA_NICSR);
-
-	if (inw(DEPCA_DATA) != STOP) {
-		return -ENXIO;
-	}
-
-	lp = netdev_priv(dev);
-	mem_start = lp->mem_start;
-
-	if (!mem_start || lp->adapter < DEPCA || lp->adapter >=unknown)
-		return -ENXIO;
-
-	printk("%s: %s at 0x%04lx",
-	       dev_name(device), depca_signature[lp->adapter], ioaddr);
-
-	switch (lp->depca_bus) {
-#ifdef CONFIG_EISA
-	case DEPCA_BUS_EISA:
-		printk(" (EISA slot %d)", to_eisa_device(device)->slot);
-		break;
-#endif
-
-	case DEPCA_BUS_ISA:
-		break;
-
-	default:
-		printk("Unknown DEPCA bus %d\n", lp->depca_bus);
-		return -ENXIO;
-	}
-
-	printk(", h/w address ");
-	status = get_hw_addr(dev);
-	printk("%pM", dev->dev_addr);
-	if (status != 0) {
-		printk("      which has an Ethernet PROM CRC error.\n");
-		return -ENXIO;
-	}
-
-	/* Set up the maximum amount of network RAM(kB) */
-	netRAM = ((lp->adapter != DEPCA) ? 64 : 48);
-	if ((nicsr & _128KB) && (lp->adapter == de422))
-		netRAM = 128;
-
-	/* Shared Memory Base Address */
-	if (nicsr & BUF) {
-		nicsr &= ~BS;	/* DEPCA RAM in top 32k */
-		netRAM -= 32;
-		mem_start += 0x8000;
-	}
-
-	if ((mem_len = (NUM_RX_DESC * (sizeof(struct depca_rx_desc) + RX_BUFF_SZ) + NUM_TX_DESC * (sizeof(struct depca_tx_desc) + TX_BUFF_SZ) + sizeof(struct depca_init)))
-	    > (netRAM << 10)) {
-		printk(",\n       requests %dkB RAM: only %dkB is available!\n", (mem_len >> 10), netRAM);
-		return -ENXIO;
-	}
-
-	printk(",\n      has %dkB RAM at 0x%.5lx", netRAM, mem_start);
-
-	/* Enable the shadow RAM. */
-	if (lp->adapter != DEPCA) {
-		nicsr |= SHE;
-		outb(nicsr, DEPCA_NICSR);
-	}
-
-	spin_lock_init(&lp->lock);
-	sprintf(lp->adapter_name, "%s (%s)",
-		depca_signature[lp->adapter], dev_name(device));
-	status = -EBUSY;
-
-	/* Initialisation Block */
-	if (!request_mem_region (mem_start, mem_len, lp->adapter_name)) {
-		printk(KERN_ERR "depca: cannot request ISA memory, aborting\n");
-		goto out_priv;
-	}
-
-	status = -EIO;
-	lp->sh_mem = ioremap(mem_start, mem_len);
-	if (lp->sh_mem == NULL) {
-		printk(KERN_ERR "depca: cannot remap ISA memory, aborting\n");
-		goto out1;
-	}
-
-	lp->mem_start = mem_start;
-	lp->mem_len   = mem_len;
-	lp->device_ram_start = mem_start & LA_MASK;
-
-	offset = 0;
-	offset += sizeof(struct depca_init);
-
-	/* Tx & Rx descriptors (aligned to a quadword boundary) */
-	offset = (offset + DEPCA_ALIGN) & ~DEPCA_ALIGN;
-	lp->rx_ring = lp->sh_mem + offset;
-	lp->rx_ring_offset = offset;
-
-	offset += (sizeof(struct depca_rx_desc) * NUM_RX_DESC);
-	lp->tx_ring = lp->sh_mem + offset;
-	lp->tx_ring_offset = offset;
-
-	offset += (sizeof(struct depca_tx_desc) * NUM_TX_DESC);
-
-	lp->buffs_offset = offset;
-
-	/* Finish initialising the ring information. */
-	lp->rxRingMask = NUM_RX_DESC - 1;
-	lp->txRingMask = NUM_TX_DESC - 1;
-
-	/* Calculate Tx/Rx RLEN size for the descriptors. */
-	for (i = 0, j = lp->rxRingMask; j > 0; i++) {
-		j >>= 1;
-	}
-	lp->rx_rlen = (s32) (i << 29);
-	for (i = 0, j = lp->txRingMask; j > 0; i++) {
-		j >>= 1;
-	}
-	lp->tx_rlen = (s32) (i << 29);
-
-	/* Load the initialisation block */
-	depca_init_ring(dev);
-
-	/* Initialise the control and status registers */
-	LoadCSRs(dev);
-
-	/* Enable DEPCA board interrupts for autoprobing */
-	nicsr = ((nicsr & ~IM) | IEN);
-	outb(nicsr, DEPCA_NICSR);
-
-	/* To auto-IRQ we enable the initialization-done and DMA err,
-	   interrupts. For now we will always get a DMA error. */
-	if (dev->irq < 2) {
-		unsigned char irqnum;
-		unsigned long irq_mask, delay;
-
-		irq_mask = probe_irq_on();
-
-		/* Assign the correct irq list */
-		switch (lp->adapter) {
-		case DEPCA:
-		case de100:
-		case de101:
-			depca_irq = de1xx_irq;
-			break;
-		case de200:
-		case de201:
-		case de202:
-		case de210:
-		case de212:
-			depca_irq = de2xx_irq;
-			break;
-		case de422:
-			depca_irq = de422_irq;
-			break;
-
-		default:
-			break;	/* Not reached */
-		}
-
-		/* Trigger an initialization just for the interrupt. */
-		outw(INEA | INIT, DEPCA_DATA);
-
-		delay = jiffies + HZ/50;
-		while (time_before(jiffies, delay))
-			yield();
-
-		irqnum = probe_irq_off(irq_mask);
-
-		status = -ENXIO;
-		if (!irqnum) {
-			printk(" and failed to detect IRQ line.\n");
-			goto out2;
-		} else {
-			for (dev->irq = 0, i = 0; (depca_irq[i]) && (!dev->irq); i++)
-				if (irqnum == depca_irq[i]) {
-					dev->irq = irqnum;
-					printk(" and uses IRQ%d.\n", dev->irq);
-				}
-
-			if (!dev->irq) {
-				printk(" but incorrect IRQ line detected.\n");
-				goto out2;
-			}
-		}
-	} else {
-		printk(" and assigned IRQ%d.\n", dev->irq);
-	}
-
-	if (depca_debug > 1) {
-		printk(version);
-	}
-
-	/* The DEPCA-specific entries in the device structure. */
-	dev->netdev_ops = &depca_netdev_ops;
-	dev->watchdog_timeo = TX_TIMEOUT;
-
-	dev->mem_start = 0;
-
-	dev_set_drvdata(device, dev);
-	SET_NETDEV_DEV (dev, device);
-
-	status = register_netdev(dev);
-	if (status == 0)
-		return 0;
-out2:
-	iounmap(lp->sh_mem);
-out1:
-	release_mem_region (mem_start, mem_len);
-out_priv:
-	return status;
-}
-
-
-static int depca_open(struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	u_long ioaddr = dev->base_addr;
-	s16 nicsr;
-	int status = 0;
-
-	STOP_DEPCA;
-	nicsr = inb(DEPCA_NICSR);
-
-	/* Make sure the shadow RAM is enabled */
-	if (lp->adapter != DEPCA) {
-		nicsr |= SHE;
-		outb(nicsr, DEPCA_NICSR);
-	}
-
-	/* Re-initialize the DEPCA... */
-	depca_init_ring(dev);
-	LoadCSRs(dev);
-
-	depca_dbg_open(dev);
-
-	if (request_irq(dev->irq, depca_interrupt, 0, lp->adapter_name, dev)) {
-		printk("depca_open(): Requested IRQ%d is busy\n", dev->irq);
-		status = -EAGAIN;
-	} else {
-
-		/* Enable DEPCA board interrupts and turn off LED */
-		nicsr = ((nicsr & ~IM & ~LED) | IEN);
-		outb(nicsr, DEPCA_NICSR);
-		outw(CSR0, DEPCA_ADDR);
-
-		netif_start_queue(dev);
-
-		status = InitRestartDepca(dev);
-
-		if (depca_debug > 1) {
-			printk("CSR0: 0x%4.4x\n", inw(DEPCA_DATA));
-			printk("nicsr: 0x%02x\n", inb(DEPCA_NICSR));
-		}
-	}
-	return status;
-}
-
-/* Initialize the lance Rx and Tx descriptor rings. */
-static void depca_init_ring(struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	u_int i;
-	u_long offset;
-
-	/* Lock out other processes whilst setting up the hardware */
-	netif_stop_queue(dev);
-
-	lp->rx_new = lp->tx_new = 0;
-	lp->rx_old = lp->tx_old = 0;
-
-	/* Initialize the base address and length of each buffer in the ring */
-	for (i = 0; i <= lp->rxRingMask; i++) {
-		offset = lp->buffs_offset + i * RX_BUFF_SZ;
-		writel((lp->device_ram_start + offset) | R_OWN, &lp->rx_ring[i].base);
-		writew(-RX_BUFF_SZ, &lp->rx_ring[i].buf_length);
-		lp->rx_buff[i] = lp->sh_mem + offset;
-	}
-
-	for (i = 0; i <= lp->txRingMask; i++) {
-		offset = lp->buffs_offset + (i + lp->rxRingMask + 1) * TX_BUFF_SZ;
-		writel((lp->device_ram_start + offset) & 0x00ffffff, &lp->tx_ring[i].base);
-		lp->tx_buff[i] = lp->sh_mem + offset;
-	}
-
-	/* Set up the initialization block */
-	lp->init_block.rx_ring = (lp->device_ram_start + lp->rx_ring_offset) | lp->rx_rlen;
-	lp->init_block.tx_ring = (lp->device_ram_start + lp->tx_ring_offset) | lp->tx_rlen;
-
-	SetMulticastFilter(dev);
-
-	for (i = 0; i < ETH_ALEN; i++) {
-		lp->init_block.phys_addr[i] = dev->dev_addr[i];
-	}
-
-	lp->init_block.mode = 0x0000;	/* Enable the Tx and Rx */
-}
-
-
-static void depca_tx_timeout(struct net_device *dev)
-{
-	u_long ioaddr = dev->base_addr;
-
-	printk("%s: transmit timed out, status %04x, resetting.\n", dev->name, inw(DEPCA_DATA));
-
-	STOP_DEPCA;
-	depca_init_ring(dev);
-	LoadCSRs(dev);
-	dev->trans_start = jiffies; /* prevent tx timeout */
-	netif_wake_queue(dev);
-	InitRestartDepca(dev);
-}
-
-
-/*
-** Writes a socket buffer to TX descriptor ring and starts transmission
-*/
-static netdev_tx_t depca_start_xmit(struct sk_buff *skb,
-				    struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	u_long ioaddr = dev->base_addr;
-	int status = 0;
-
-	/* Transmitter timeout, serious problems. */
-	if (skb->len < 1)
-		goto out;
-
-	if (skb_padto(skb, ETH_ZLEN))
-		goto out;
-
-	netif_stop_queue(dev);
-
-	if (TX_BUFFS_AVAIL) {	/* Fill in a Tx ring entry */
-		status = load_packet(dev, skb);
-
-		if (!status) {
-			/* Trigger an immediate send demand. */
-			outw(CSR0, DEPCA_ADDR);
-			outw(INEA | TDMD, DEPCA_DATA);
-
-			dev_kfree_skb(skb);
-		}
-		if (TX_BUFFS_AVAIL)
-			netif_start_queue(dev);
-	} else
-		status = NETDEV_TX_LOCKED;
-
-      out:
-	return status;
-}
-
-/*
-** The DEPCA interrupt handler.
-*/
-static irqreturn_t depca_interrupt(int irq, void *dev_id)
-{
-	struct net_device *dev = dev_id;
-	struct depca_private *lp;
-	s16 csr0, nicsr;
-	u_long ioaddr;
-
-	if (dev == NULL) {
-		printk("depca_interrupt(): irq %d for unknown device.\n", irq);
-		return IRQ_NONE;
-	}
-
-	lp = netdev_priv(dev);
-	ioaddr = dev->base_addr;
-
-	spin_lock(&lp->lock);
-
-	/* mask the DEPCA board interrupts and turn on the LED */
-	nicsr = inb(DEPCA_NICSR);
-	nicsr |= (IM | LED);
-	outb(nicsr, DEPCA_NICSR);
-
-	outw(CSR0, DEPCA_ADDR);
-	csr0 = inw(DEPCA_DATA);
-
-	/* Acknowledge all of the current interrupt sources ASAP. */
-	outw(csr0 & INTE, DEPCA_DATA);
-
-	if (csr0 & RINT)	/* Rx interrupt (packet arrived) */
-		depca_rx(dev);
-
-	if (csr0 & TINT)	/* Tx interrupt (packet sent) */
-		depca_tx(dev);
-
-	/* Any resources available? */
-	if ((TX_BUFFS_AVAIL >= 0) && netif_queue_stopped(dev)) {
-		netif_wake_queue(dev);
-	}
-
-	/* Unmask the DEPCA board interrupts and turn off the LED */
-	nicsr = (nicsr & ~IM & ~LED);
-	outb(nicsr, DEPCA_NICSR);
-
-	spin_unlock(&lp->lock);
-	return IRQ_HANDLED;
-}
-
-/* Called with lp->lock held */
-static int depca_rx(struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	int i, entry;
-	s32 status;
-
-	for (entry = lp->rx_new; !(readl(&lp->rx_ring[entry].base) & R_OWN); entry = lp->rx_new) {
-		status = readl(&lp->rx_ring[entry].base) >> 16;
-		if (status & R_STP) {	/* Remember start of frame */
-			lp->rx_old = entry;
-		}
-		if (status & R_ENP) {	/* Valid frame status */
-			if (status & R_ERR) {	/* There was an error. */
-				dev->stats.rx_errors++;	/* Update the error stats. */
-				if (status & R_FRAM)
-					dev->stats.rx_frame_errors++;
-				if (status & R_OFLO)
-					dev->stats.rx_over_errors++;
-				if (status & R_CRC)
-					dev->stats.rx_crc_errors++;
-				if (status & R_BUFF)
-					dev->stats.rx_fifo_errors++;
-			} else {
-				short len, pkt_len = readw(&lp->rx_ring[entry].msg_length) - 4;
-				struct sk_buff *skb;
-
-				skb = netdev_alloc_skb(dev, pkt_len + 2);
-				if (skb != NULL) {
-					unsigned char *buf;
-					skb_reserve(skb, 2);	/* 16 byte align the IP header */
-					buf = skb_put(skb, pkt_len);
-					if (entry < lp->rx_old) {	/* Wrapped buffer */
-						len = (lp->rxRingMask - lp->rx_old + 1) * RX_BUFF_SZ;
-						memcpy_fromio(buf, lp->rx_buff[lp->rx_old], len);
-						memcpy_fromio(buf + len, lp->rx_buff[0], pkt_len - len);
-					} else {	/* Linear buffer */
-						memcpy_fromio(buf, lp->rx_buff[lp->rx_old], pkt_len);
-					}
-
-					/*
-					   ** Notify the upper protocol layers that there is another
-					   ** packet to handle
-					 */
-					skb->protocol = eth_type_trans(skb, dev);
-					netif_rx(skb);
-
-					/*
-					   ** Update stats
-					 */
-					dev->stats.rx_packets++;
-					dev->stats.rx_bytes += pkt_len;
-					for (i = 1; i < DEPCA_PKT_STAT_SZ - 1; i++) {
-						if (pkt_len < (i * DEPCA_PKT_BIN_SZ)) {
-							lp->pktStats.bins[i]++;
-							i = DEPCA_PKT_STAT_SZ;
-						}
-					}
-					if (is_multicast_ether_addr(buf)) {
-						if (is_broadcast_ether_addr(buf)) {
-							lp->pktStats.broadcast++;
-						} else {
-							lp->pktStats.multicast++;
-						}
-					} else if (ether_addr_equal(buf,
-								    dev->dev_addr)) {
-						lp->pktStats.unicast++;
-					}
-
-					lp->pktStats.bins[0]++;	/* Duplicates stats.rx_packets */
-					if (lp->pktStats.bins[0] == 0) {	/* Reset counters */
-						memset((char *) &lp->pktStats, 0, sizeof(lp->pktStats));
-					}
-				} else {
-					printk("%s: Memory squeeze, deferring packet.\n", dev->name);
-					dev->stats.rx_dropped++;	/* Really, deferred. */
-					break;
-				}
-			}
-			/* Change buffer ownership for this last frame, back to the adapter */
-			for (; lp->rx_old != entry; lp->rx_old = (lp->rx_old + 1) & lp->rxRingMask) {
-				writel(readl(&lp->rx_ring[lp->rx_old].base) | R_OWN, &lp->rx_ring[lp->rx_old].base);
-			}
-			writel(readl(&lp->rx_ring[entry].base) | R_OWN, &lp->rx_ring[entry].base);
-		}
-
-		/*
-		   ** Update entry information
-		 */
-		lp->rx_new = (lp->rx_new + 1) & lp->rxRingMask;
-	}
-
-	return 0;
-}
-
-/*
-** Buffer sent - check for buffer errors.
-** Called with lp->lock held
-*/
-static int depca_tx(struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	int entry;
-	s32 status;
-	u_long ioaddr = dev->base_addr;
-
-	for (entry = lp->tx_old; entry != lp->tx_new; entry = lp->tx_old) {
-		status = readl(&lp->tx_ring[entry].base) >> 16;
-
-		if (status < 0) {	/* Packet not yet sent! */
-			break;
-		} else if (status & T_ERR) {	/* An error occurred. */
-			status = readl(&lp->tx_ring[entry].misc);
-			dev->stats.tx_errors++;
-			if (status & TMD3_RTRY)
-				dev->stats.tx_aborted_errors++;
-			if (status & TMD3_LCAR)
-				dev->stats.tx_carrier_errors++;
-			if (status & TMD3_LCOL)
-				dev->stats.tx_window_errors++;
-			if (status & TMD3_UFLO)
-				dev->stats.tx_fifo_errors++;
-			if (status & (TMD3_BUFF | TMD3_UFLO)) {
-				/* Trigger an immediate send demand. */
-				outw(CSR0, DEPCA_ADDR);
-				outw(INEA | TDMD, DEPCA_DATA);
-			}
-		} else if (status & (T_MORE | T_ONE)) {
-			dev->stats.collisions++;
-		} else {
-			dev->stats.tx_packets++;
-		}
-
-		/* Update all the pointers */
-		lp->tx_old = (lp->tx_old + 1) & lp->txRingMask;
-	}
-
-	return 0;
-}
-
-static int depca_close(struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	s16 nicsr;
-	u_long ioaddr = dev->base_addr;
-
-	netif_stop_queue(dev);
-
-	outw(CSR0, DEPCA_ADDR);
-
-	if (depca_debug > 1) {
-		printk("%s: Shutting down ethercard, status was %2.2x.\n", dev->name, inw(DEPCA_DATA));
-	}
-
-	/*
-	   ** We stop the DEPCA here -- it occasionally polls
-	   ** memory if we don't.
-	 */
-	outw(STOP, DEPCA_DATA);
-
-	/*
-	   ** Give back the ROM in case the user wants to go to DOS
-	 */
-	if (lp->adapter != DEPCA) {
-		nicsr = inb(DEPCA_NICSR);
-		nicsr &= ~SHE;
-		outb(nicsr, DEPCA_NICSR);
-	}
-
-	/*
-	   ** Free the associated irq
-	 */
-	free_irq(dev->irq, dev);
-	return 0;
-}
-
-static void LoadCSRs(struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	u_long ioaddr = dev->base_addr;
-
-	outw(CSR1, DEPCA_ADDR);	/* initialisation block address LSW */
-	outw((u16) lp->device_ram_start, DEPCA_DATA);
-	outw(CSR2, DEPCA_ADDR);	/* initialisation block address MSW */
-	outw((u16) (lp->device_ram_start >> 16), DEPCA_DATA);
-	outw(CSR3, DEPCA_ADDR);	/* ALE control */
-	outw(ACON, DEPCA_DATA);
-
-	outw(CSR0, DEPCA_ADDR);	/* Point back to CSR0 */
-}
-
-static int InitRestartDepca(struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	u_long ioaddr = dev->base_addr;
-	int i, status = 0;
-
-	/* Copy the shadow init_block to shared memory */
-	memcpy_toio(lp->sh_mem, &lp->init_block, sizeof(struct depca_init));
-
-	outw(CSR0, DEPCA_ADDR);	/* point back to CSR0 */
-	outw(INIT, DEPCA_DATA);	/* initialize DEPCA */
-
-	/* wait for lance to complete initialisation */
-	for (i = 0; (i < 100) && !(inw(DEPCA_DATA) & IDON); i++);
-
-	if (i != 100) {
-		/* clear IDON by writing a "1", enable interrupts and start lance */
-		outw(IDON | INEA | STRT, DEPCA_DATA);
-		if (depca_debug > 2) {
-			printk("%s: DEPCA open after %d ticks, init block 0x%08lx csr0 %4.4x.\n", dev->name, i, lp->mem_start, inw(DEPCA_DATA));
-		}
-	} else {
-		printk("%s: DEPCA unopen after %d ticks, init block 0x%08lx csr0 %4.4x.\n", dev->name, i, lp->mem_start, inw(DEPCA_DATA));
-		status = -1;
-	}
-
-	return status;
-}
-
-/*
-** Set or clear the multicast filter for this adaptor.
-*/
-static void set_multicast_list(struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	u_long ioaddr = dev->base_addr;
-
-	netif_stop_queue(dev);
-	while (lp->tx_old != lp->tx_new);	/* Wait for the ring to empty */
-
-	STOP_DEPCA;	/* Temporarily stop the depca.  */
-	depca_init_ring(dev);	/* Initialize the descriptor rings */
-
-	if (dev->flags & IFF_PROMISC) {	/* Set promiscuous mode */
-		lp->init_block.mode |= PROM;
-	} else {
-		SetMulticastFilter(dev);
-		lp->init_block.mode &= ~PROM;	/* Unset promiscuous mode */
-	}
-
-	LoadCSRs(dev);	/* Reload CSR3 */
-	InitRestartDepca(dev);	/* Resume normal operation. */
-	netif_start_queue(dev);	/* Unlock the TX ring */
-}
-
-/*
-** Calculate the hash code and update the logical address filter
-** from a list of ethernet multicast addresses.
-** Big endian crc one liner is mine, all mine, ha ha ha ha!
-** LANCE calculates its hash codes big endian.
-*/
-static void SetMulticastFilter(struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	struct netdev_hw_addr *ha;
-	int i, j, bit, byte;
-	u16 hashcode;
-	u32 crc;
-
-	if (dev->flags & IFF_ALLMULTI) {	/* Set all multicast bits */
-		for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
-			lp->init_block.mcast_table[i] = (char) 0xff;
-		}
-	} else {
-		for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {	/* Clear the multicast table */
-			lp->init_block.mcast_table[i] = 0;
-		}
-		/* Add multicast addresses */
-		netdev_for_each_mc_addr(ha, dev) {
-			crc = ether_crc(ETH_ALEN, ha->addr);
-			hashcode = (crc & 1);	/* hashcode is 6 LSb of CRC ... */
-			for (j = 0; j < 5; j++) {	/* ... in reverse order. */
-				hashcode = (hashcode << 1) | ((crc >>= 1) & 1);
-			}
-
-			byte = hashcode >> 3;	/* bit[3-5] -> byte in filter */
-			bit = 1 << (hashcode & 0x07);	/* bit[0-2] -> bit in byte */
-			lp->init_block.mcast_table[byte] |= bit;
-		}
-	}
-}
-
-static int __init depca_common_init (u_long ioaddr, struct net_device **devp)
-{
-	int status = 0;
-
-	if (!request_region (ioaddr, DEPCA_TOTAL_SIZE, depca_string)) {
-		status = -EBUSY;
-		goto out;
-	}
-
-	if (DevicePresent(ioaddr)) {
-		status = -ENODEV;
-		goto out_release;
-	}
-
-	if (!(*devp = alloc_etherdev (sizeof (struct depca_private)))) {
-		status = -ENOMEM;
-		goto out_release;
-	}
-
-	return 0;
-
- out_release:
-	release_region (ioaddr, DEPCA_TOTAL_SIZE);
- out:
-	return status;
-}
-
-/*
-** ISA bus I/O device probe
-*/
-
-static void __init depca_platform_probe (void)
-{
-	int i;
-	struct platform_device *pldev;
-
-	for (i = 0; depca_io_ports[i].iobase; i++) {
-		depca_io_ports[i].device = NULL;
-
-		/* if an address has been specified on the command
-		 * line, use it (if valid) */
-		if (io && io != depca_io_ports[i].iobase)
-			continue;
-
-		pldev = platform_device_alloc(depca_string, i);
-		if (!pldev)
-			continue;
-
-		pldev->dev.platform_data = (void *) depca_io_ports[i].iobase;
-		depca_io_ports[i].device = pldev;
-
-		if (platform_device_add(pldev)) {
-			depca_io_ports[i].device = NULL;
-			pldev->dev.platform_data = NULL;
-			platform_device_put(pldev);
-			continue;
-		}
-
-		if (!pldev->dev.driver) {
-		/* The driver was not bound to this device, there was
-		 * no hardware at this address. Unregister it, as the
-		 * release function will take care of freeing the
-		 * allocated structure */
-
-			depca_io_ports[i].device = NULL;
-			pldev->dev.platform_data = NULL;
-			platform_device_unregister (pldev);
-		}
-	}
-}
-
-static enum depca_type __init depca_shmem_probe (ulong *mem_start)
-{
-	u_long mem_base[] = DEPCA_RAM_BASE_ADDRESSES;
-	enum depca_type adapter = unknown;
-	int i;
-
-	for (i = 0; mem_base[i]; i++) {
-		*mem_start = mem ? mem : mem_base[i];
-		adapter = DepcaSignature (adapter_name, *mem_start);
-		if (adapter != unknown)
-			break;
-	}
-
-	return adapter;
-}
-
-static int depca_isa_probe(struct platform_device *device)
-{
-	struct net_device *dev;
-	struct depca_private *lp;
-	u_long ioaddr, mem_start = 0;
-	enum depca_type adapter = unknown;
-	int status = 0;
-
-	ioaddr = (u_long) device->dev.platform_data;
-
-	if ((status = depca_common_init (ioaddr, &dev)))
-		goto out;
-
-	adapter = depca_shmem_probe (&mem_start);
-
-	if (adapter == unknown) {
-		status = -ENODEV;
-		goto out_free;
-	}
-
-	dev->base_addr = ioaddr;
-	dev->irq = irq;		/* Use whatever value the user gave
-				 * us, and 0 if he didn't. */
-	lp = netdev_priv(dev);
-	lp->depca_bus = DEPCA_BUS_ISA;
-	lp->adapter = adapter;
-	lp->mem_start = mem_start;
-
-	if ((status = depca_hw_init(dev, &device->dev)))
-		goto out_free;
-
-	return 0;
-
- out_free:
-	free_netdev (dev);
-	release_region (ioaddr, DEPCA_TOTAL_SIZE);
- out:
-	return status;
-}
-
-/*
-** EISA callbacks from sysfs.
-*/
-
-#ifdef CONFIG_EISA
-static int __init depca_eisa_probe (struct device *device)
-{
-	enum depca_type adapter = unknown;
-	struct eisa_device *edev;
-	struct net_device *dev;
-	struct depca_private *lp;
-	u_long ioaddr, mem_start;
-	int status = 0;
-
-	edev = to_eisa_device (device);
-	ioaddr = edev->base_addr + DEPCA_EISA_IO_PORTS;
-
-	if ((status = depca_common_init (ioaddr, &dev)))
-		goto out;
-
-	/* It would have been nice to get card configuration from the
-	 * card. Unfortunately, this register is write-only (shares
-	 * it's address with the ethernet prom)... As we don't parse
-	 * the EISA configuration structures (yet... :-), just rely on
-	 * the ISA probing to sort it out... */
-
-	adapter = depca_shmem_probe (&mem_start);
-	if (adapter == unknown) {
-		status = -ENODEV;
-		goto out_free;
-	}
-
-	dev->base_addr = ioaddr;
-	dev->irq = irq;
-	lp = netdev_priv(dev);
-	lp->depca_bus = DEPCA_BUS_EISA;
-	lp->adapter = edev->id.driver_data;
-	lp->mem_start = mem_start;
-
-	if ((status = depca_hw_init(dev, device)))
-		goto out_free;
-
-	return 0;
-
- out_free:
-	free_netdev (dev);
-	release_region (ioaddr, DEPCA_TOTAL_SIZE);
- out:
-	return status;
-}
-#endif
-
-static int depca_device_remove(struct device *device)
-{
-	struct net_device *dev;
-	struct depca_private *lp;
-	int bus;
-
-	dev  = dev_get_drvdata(device);
-	lp   = netdev_priv(dev);
-
-	unregister_netdev (dev);
-	iounmap (lp->sh_mem);
-	release_mem_region (lp->mem_start, lp->mem_len);
-	release_region (dev->base_addr, DEPCA_TOTAL_SIZE);
-	bus = lp->depca_bus;
-	free_netdev (dev);
-
-	return 0;
-}
-
-/*
-** Look for a particular board name in the on-board Remote Diagnostics
-** and Boot (readb) ROM. This will also give us a clue to the network RAM
-** base address.
-*/
-static int __init DepcaSignature(char *name, u_long base_addr)
-{
-	u_int i, j, k;
-	void __iomem *ptr;
-	char tmpstr[16];
-	u_long prom_addr = base_addr + 0xc000;
-	u_long mem_addr = base_addr + 0x8000; /* 32KB */
-
-	/* Can't reserve the prom region, it is already marked as
-	 * used, at least on x86. Instead, reserve a memory region a
-	 * board would certainly use. If it works, go ahead. If not,
-	 * run like hell... */
-
-	if (!request_mem_region (mem_addr, 16, depca_string))
-		return unknown;
-
-	/* Copy the first 16 bytes of ROM */
-
-	ptr = ioremap(prom_addr, 16);
-	if (ptr == NULL) {
-		printk(KERN_ERR "depca: I/O remap failed at %lx\n", prom_addr);
-		return unknown;
-	}
-	for (i = 0; i < 16; i++) {
-		tmpstr[i] = readb(ptr + i);
-	}
-	iounmap(ptr);
-
-	release_mem_region (mem_addr, 16);
-
-	/* Check if PROM contains a valid string */
-	for (i = 0; *depca_signature[i] != '\0'; i++) {
-		for (j = 0, k = 0; j < 16 && k < strlen(depca_signature[i]); j++) {
-			if (depca_signature[i][k] == tmpstr[j]) {	/* track signature */
-				k++;
-			} else {	/* lost signature; begin search again */
-				k = 0;
-			}
-		}
-		if (k == strlen(depca_signature[i]))
-			break;
-	}
-
-	/* Check if name string is valid, provided there's no PROM */
-	if (name && *name && (i == unknown)) {
-		for (i = 0; *depca_signature[i] != '\0'; i++) {
-			if (strcmp(name, depca_signature[i]) == 0)
-				break;
-		}
-	}
-
-	return i;
-}
-
-/*
-** Look for a special sequence in the Ethernet station address PROM that
-** is common across all DEPCA products. Note that the original DEPCA needs
-** its ROM address counter to be initialized and enabled. Only enable
-** if the first address octet is a 0x08 - this minimises the chances of
-** messing around with some other hardware, but it assumes that this DEPCA
-** card initialized itself correctly.
-**
-** Search the Ethernet address ROM for the signature. Since the ROM address
-** counter can start at an arbitrary point, the search must include the entire
-** probe sequence length plus the (length_of_the_signature - 1).
-** Stop the search IMMEDIATELY after the signature is found so that the
-** PROM address counter is correctly positioned at the start of the
-** ethernet address for later read out.
-*/
-static int __init DevicePresent(u_long ioaddr)
-{
-	union {
-		struct {
-			u32 a;
-			u32 b;
-		} llsig;
-		char Sig[sizeof(u32) << 1];
-	}
-	dev;
-	short sigLength = 0;
-	s8 data;
-	s16 nicsr;
-	int i, j, status = 0;
-
-	data = inb(DEPCA_PROM);	/* clear counter on DEPCA */
-	data = inb(DEPCA_PROM);	/* read data */
-
-	if (data == 0x08) {	/* Enable counter on DEPCA */
-		nicsr = inb(DEPCA_NICSR);
-		nicsr |= AAC;
-		outb(nicsr, DEPCA_NICSR);
-	}
-
-	dev.llsig.a = ETH_PROM_SIG;
-	dev.llsig.b = ETH_PROM_SIG;
-	sigLength = sizeof(u32) << 1;
-
-	for (i = 0, j = 0; j < sigLength && i < PROBE_LENGTH + sigLength - 1; i++) {
-		data = inb(DEPCA_PROM);
-		if (dev.Sig[j] == data) {	/* track signature */
-			j++;
-		} else {	/* lost signature; begin search again */
-			if (data == dev.Sig[0]) {	/* rare case.... */
-				j = 1;
-			} else {
-				j = 0;
-			}
-		}
-	}
-
-	if (j != sigLength) {
-		status = -ENODEV;	/* search failed */
-	}
-
-	return status;
-}
-
-/*
-** The DE100 and DE101 PROM accesses were made non-standard for some bizarre
-** reason: access the upper half of the PROM with x=0; access the lower half
-** with x=1.
-*/
-static int __init get_hw_addr(struct net_device *dev)
-{
-	u_long ioaddr = dev->base_addr;
-	struct depca_private *lp = netdev_priv(dev);
-	int i, k, tmp, status = 0;
-	u_short j, x, chksum;
-
-	x = (((lp->adapter == de100) || (lp->adapter == de101)) ? 1 : 0);
-
-	for (i = 0, k = 0, j = 0; j < 3; j++) {
-		k <<= 1;
-		if (k > 0xffff)
-			k -= 0xffff;
-
-		k += (u_char) (tmp = inb(DEPCA_PROM + x));
-		dev->dev_addr[i++] = (u_char) tmp;
-		k += (u_short) ((tmp = inb(DEPCA_PROM + x)) << 8);
-		dev->dev_addr[i++] = (u_char) tmp;
-
-		if (k > 0xffff)
-			k -= 0xffff;
-	}
-	if (k == 0xffff)
-		k = 0;
-
-	chksum = (u_char) inb(DEPCA_PROM + x);
-	chksum |= (u_short) (inb(DEPCA_PROM + x) << 8);
-	if (k != chksum)
-		status = -1;
-
-	return status;
-}
-
-/*
-** Load a packet into the shared memory
-*/
-static int load_packet(struct net_device *dev, struct sk_buff *skb)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	int i, entry, end, len, status = NETDEV_TX_OK;
-
-	entry = lp->tx_new;	/* Ring around buffer number. */
-	end = (entry + (skb->len - 1) / TX_BUFF_SZ) & lp->txRingMask;
-	if (!(readl(&lp->tx_ring[end].base) & T_OWN)) {	/* Enough room? */
-		/*
-		   ** Caution: the write order is important here... don't set up the
-		   ** ownership rights until all the other information is in place.
-		 */
-		if (end < entry) {	/* wrapped buffer */
-			len = (lp->txRingMask - entry + 1) * TX_BUFF_SZ;
-			memcpy_toio(lp->tx_buff[entry], skb->data, len);
-			memcpy_toio(lp->tx_buff[0], skb->data + len, skb->len - len);
-		} else {	/* linear buffer */
-			memcpy_toio(lp->tx_buff[entry], skb->data, skb->len);
-		}
-
-		/* set up the buffer descriptors */
-		len = (skb->len < ETH_ZLEN) ? ETH_ZLEN : skb->len;
-		for (i = entry; i != end; i = (i+1) & lp->txRingMask) {
-			/* clean out flags */
-			writel(readl(&lp->tx_ring[i].base) & ~T_FLAGS, &lp->tx_ring[i].base);
-			writew(0x0000, &lp->tx_ring[i].misc);	/* clears other error flags */
-			writew(-TX_BUFF_SZ, &lp->tx_ring[i].length);	/* packet length in buffer */
-			len -= TX_BUFF_SZ;
-		}
-		/* clean out flags */
-		writel(readl(&lp->tx_ring[end].base) & ~T_FLAGS, &lp->tx_ring[end].base);
-		writew(0x0000, &lp->tx_ring[end].misc);	/* clears other error flags */
-		writew(-len, &lp->tx_ring[end].length);	/* packet length in last buff */
-
-		/* start of packet */
-		writel(readl(&lp->tx_ring[entry].base) | T_STP, &lp->tx_ring[entry].base);
-		/* end of packet */
-		writel(readl(&lp->tx_ring[end].base) | T_ENP, &lp->tx_ring[end].base);
-
-		for (i = end; i != entry; --i) {
-			/* ownership of packet */
-			writel(readl(&lp->tx_ring[i].base) | T_OWN, &lp->tx_ring[i].base);
-			if (i == 0)
-				i = lp->txRingMask + 1;
-		}
-		writel(readl(&lp->tx_ring[entry].base) | T_OWN, &lp->tx_ring[entry].base);
-
-		lp->tx_new = (++end) & lp->txRingMask;	/* update current pointers */
-	} else {
-		status = NETDEV_TX_LOCKED;
-	}
-
-	return status;
-}
-
-static void depca_dbg_open(struct net_device *dev)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	u_long ioaddr = dev->base_addr;
-	struct depca_init *p = &lp->init_block;
-	int i;
-
-	if (depca_debug > 1) {
-		/* Do not copy the shadow init block into shared memory */
-		/* Debugging should not affect normal operation! */
-		/* The shadow init block will get copied across during InitRestartDepca */
-		printk("%s: depca open with irq %d\n", dev->name, dev->irq);
-		printk("Descriptor head addresses (CPU):\n");
-		printk("        0x%lx  0x%lx\n", (u_long) lp->rx_ring, (u_long) lp->tx_ring);
-		printk("Descriptor addresses (CPU):\nRX: ");
-		for (i = 0; i < lp->rxRingMask; i++) {
-			if (i < 3) {
-				printk("%p ", &lp->rx_ring[i].base);
-			}
-		}
-		printk("...%p\n", &lp->rx_ring[i].base);
-		printk("TX: ");
-		for (i = 0; i < lp->txRingMask; i++) {
-			if (i < 3) {
-				printk("%p ", &lp->tx_ring[i].base);
-			}
-		}
-		printk("...%p\n", &lp->tx_ring[i].base);
-		printk("\nDescriptor buffers (Device):\nRX: ");
-		for (i = 0; i < lp->rxRingMask; i++) {
-			if (i < 3) {
-				printk("0x%8.8x  ", readl(&lp->rx_ring[i].base));
-			}
-		}
-		printk("...0x%8.8x\n", readl(&lp->rx_ring[i].base));
-		printk("TX: ");
-		for (i = 0; i < lp->txRingMask; i++) {
-			if (i < 3) {
-				printk("0x%8.8x  ", readl(&lp->tx_ring[i].base));
-			}
-		}
-		printk("...0x%8.8x\n", readl(&lp->tx_ring[i].base));
-		printk("Initialisation block at 0x%8.8lx(Phys)\n", lp->mem_start);
-		printk("        mode: 0x%4.4x\n", p->mode);
-		printk("        physical address: %pM\n", p->phys_addr);
-		printk("        multicast hash table: ");
-		for (i = 0; i < (HASH_TABLE_LEN >> 3) - 1; i++) {
-			printk("%2.2x:", p->mcast_table[i]);
-		}
-		printk("%2.2x\n", p->mcast_table[i]);
-		printk("        rx_ring at: 0x%8.8x\n", p->rx_ring);
-		printk("        tx_ring at: 0x%8.8x\n", p->tx_ring);
-		printk("buffers (Phys): 0x%8.8lx\n", lp->mem_start + lp->buffs_offset);
-		printk("Ring size:\nRX: %d  Log2(rxRingMask): 0x%8.8x\n", (int) lp->rxRingMask + 1, lp->rx_rlen);
-		printk("TX: %d  Log2(txRingMask): 0x%8.8x\n", (int) lp->txRingMask + 1, lp->tx_rlen);
-		outw(CSR2, DEPCA_ADDR);
-		printk("CSR2&1: 0x%4.4x", inw(DEPCA_DATA));
-		outw(CSR1, DEPCA_ADDR);
-		printk("%4.4x\n", inw(DEPCA_DATA));
-		outw(CSR3, DEPCA_ADDR);
-		printk("CSR3: 0x%4.4x\n", inw(DEPCA_DATA));
-	}
-}
-
-/*
-** Perform IOCTL call functions here. Some are privileged operations and the
-** effective uid is checked in those cases.
-** All multicast IOCTLs will not work here and are for testing purposes only.
-*/
-static int depca_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
-{
-	struct depca_private *lp = netdev_priv(dev);
-	struct depca_ioctl *ioc = (struct depca_ioctl *) &rq->ifr_ifru;
-	int i, status = 0;
-	u_long ioaddr = dev->base_addr;
-	union {
-		u8 addr[(HASH_TABLE_LEN * ETH_ALEN)];
-		u16 sval[(HASH_TABLE_LEN * ETH_ALEN) >> 1];
-		u32 lval[(HASH_TABLE_LEN * ETH_ALEN) >> 2];
-	} tmp;
-	unsigned long flags;
-	void *buf;
-
-	switch (ioc->cmd) {
-	case DEPCA_GET_HWADDR:	/* Get the hardware address */
-		for (i = 0; i < ETH_ALEN; i++) {
-			tmp.addr[i] = dev->dev_addr[i];
-		}
-		ioc->len = ETH_ALEN;
-		if (copy_to_user(ioc->data, tmp.addr, ioc->len))
-			return -EFAULT;
-		break;
-
-	case DEPCA_SET_HWADDR:	/* Set the hardware address */
-		if (!capable(CAP_NET_ADMIN))
-			return -EPERM;
-		if (copy_from_user(tmp.addr, ioc->data, ETH_ALEN))
-			return -EFAULT;
-		for (i = 0; i < ETH_ALEN; i++) {
-			dev->dev_addr[i] = tmp.addr[i];
-		}
-		netif_stop_queue(dev);
-		while (lp->tx_old != lp->tx_new)
-			cpu_relax();	/* Wait for the ring to empty */
-
-		STOP_DEPCA;	/* Temporarily stop the depca.  */
-		depca_init_ring(dev);	/* Initialize the descriptor rings */
-		LoadCSRs(dev);	/* Reload CSR3 */
-		InitRestartDepca(dev);	/* Resume normal operation. */
-		netif_start_queue(dev);	/* Unlock the TX ring */
-		break;
-
-	case DEPCA_SET_PROM:	/* Set Promiscuous Mode */
-		if (!capable(CAP_NET_ADMIN))
-			return -EPERM;
-		netif_stop_queue(dev);
-		while (lp->tx_old != lp->tx_new)
-			cpu_relax();	/* Wait for the ring to empty */
-
-		STOP_DEPCA;	/* Temporarily stop the depca.  */
-		depca_init_ring(dev);	/* Initialize the descriptor rings */
-		lp->init_block.mode |= PROM;	/* Set promiscuous mode */
-
-		LoadCSRs(dev);	/* Reload CSR3 */
-		InitRestartDepca(dev);	/* Resume normal operation. */
-		netif_start_queue(dev);	/* Unlock the TX ring */
-		break;
-
-	case DEPCA_CLR_PROM:	/* Clear Promiscuous Mode */
-		if (!capable(CAP_NET_ADMIN))
-			return -EPERM;
-		netif_stop_queue(dev);
-		while (lp->tx_old != lp->tx_new)
-			cpu_relax();	/* Wait for the ring to empty */
-
-		STOP_DEPCA;	/* Temporarily stop the depca.  */
-		depca_init_ring(dev);	/* Initialize the descriptor rings */
-		lp->init_block.mode &= ~PROM;	/* Clear promiscuous mode */
-
-		LoadCSRs(dev);	/* Reload CSR3 */
-		InitRestartDepca(dev);	/* Resume normal operation. */
-		netif_start_queue(dev);	/* Unlock the TX ring */
-		break;
-
-	case DEPCA_SAY_BOO:	/* Say "Boo!" to the kernel log file */
-		if(!capable(CAP_NET_ADMIN))
-			return -EPERM;
-		printk("%s: Boo!\n", dev->name);
-		break;
-
-	case DEPCA_GET_MCA:	/* Get the multicast address table */
-		ioc->len = (HASH_TABLE_LEN >> 3);
-		if (copy_to_user(ioc->data, lp->init_block.mcast_table, ioc->len))
-			return -EFAULT;
-		break;
-
-	case DEPCA_SET_MCA:	/* Set a multicast address */
-		if (!capable(CAP_NET_ADMIN))
-			return -EPERM;
-		if (ioc->len >= HASH_TABLE_LEN)
-			return -EINVAL;
-		if (copy_from_user(tmp.addr, ioc->data, ETH_ALEN * ioc->len))
-			return -EFAULT;
-		set_multicast_list(dev);
-		break;
-
-	case DEPCA_CLR_MCA:	/* Clear all multicast addresses */
-		if (!capable(CAP_NET_ADMIN))
-			return -EPERM;
-		set_multicast_list(dev);
-		break;
-
-	case DEPCA_MCA_EN:	/* Enable pass all multicast addressing */
-		if (!capable(CAP_NET_ADMIN))
-			return -EPERM;
-		set_multicast_list(dev);
-		break;
-
-	case DEPCA_GET_STATS:	/* Get the driver statistics */
-		ioc->len = sizeof(lp->pktStats);
-		buf = kmalloc(ioc->len, GFP_KERNEL);
-		if(!buf)
-			return -ENOMEM;
-		spin_lock_irqsave(&lp->lock, flags);
-		memcpy(buf, &lp->pktStats, ioc->len);
-		spin_unlock_irqrestore(&lp->lock, flags);
-		if (copy_to_user(ioc->data, buf, ioc->len))
-			status = -EFAULT;
-		kfree(buf);
-		break;
-
-	case DEPCA_CLR_STATS:	/* Zero out the driver statistics */
-		if (!capable(CAP_NET_ADMIN))
-			return -EPERM;
-		spin_lock_irqsave(&lp->lock, flags);
-		memset(&lp->pktStats, 0, sizeof(lp->pktStats));
-		spin_unlock_irqrestore(&lp->lock, flags);
-		break;
-
-	case DEPCA_GET_REG:	/* Get the DEPCA Registers */
-		i = 0;
-		tmp.sval[i++] = inw(DEPCA_NICSR);
-		outw(CSR0, DEPCA_ADDR);	/* status register */
-		tmp.sval[i++] = inw(DEPCA_DATA);
-		memcpy(&tmp.sval[i], &lp->init_block, sizeof(struct depca_init));
-		ioc->len = i + sizeof(struct depca_init);
-		if (copy_to_user(ioc->data, tmp.addr, ioc->len))
-			return -EFAULT;
-		break;
-
-	default:
-		return -EOPNOTSUPP;
-	}
-
-	return status;
-}
-
-static int __init depca_module_init (void)
-{
-	int err = 0;
-
-#ifdef CONFIG_EISA
-	err = eisa_driver_register(&depca_eisa_driver);
-	if (err)
-		goto err_eisa;
-#endif
-	err = platform_driver_register(&depca_isa_driver);
-	if (err)
-		goto err_eisa;
-
-	depca_platform_probe();
-	return 0;
-
-err_eisa:
-#ifdef CONFIG_EISA
-	eisa_driver_unregister(&depca_eisa_driver);
-#endif
-	return err;
-}
-
-static void __exit depca_module_exit (void)
-{
-	int i;
-#ifdef CONFIG_EISA
-        eisa_driver_unregister (&depca_eisa_driver);
-#endif
-	platform_driver_unregister (&depca_isa_driver);
-
-	for (i = 0; depca_io_ports[i].iobase; i++) {
-		if (depca_io_ports[i].device) {
-			depca_io_ports[i].device->dev.platform_data = NULL;
-			platform_device_unregister (depca_io_ports[i].device);
-			depca_io_ports[i].device = NULL;
-		}
-	}
-}
-
-module_init (depca_module_init);
-module_exit (depca_module_exit);
diff --git a/drivers/net/ethernet/amd/depca.h b/drivers/net/ethernet/amd/depca.h
deleted file mode 100644
index cdcfe4252c16..000000000000
--- a/drivers/net/ethernet/amd/depca.h
+++ /dev/null
@@ -1,183 +0,0 @@
-/*
-    Written 1994 by David C. Davies.
-
-    Copyright 1994 David C. Davies. This software may be used and distributed
-    according to the terms of the GNU General Public License, incorporated herein by
-    reference.
-*/
-
-/*
-** I/O addresses. Note that the 2k buffer option is not supported in
-** this driver.
-*/
-#define DEPCA_NICSR ioaddr+0x00   /* Network interface CSR */
-#define DEPCA_RBI   ioaddr+0x02   /* RAM buffer index (2k buffer mode) */
-#define DEPCA_DATA  ioaddr+0x04   /* LANCE registers' data port */
-#define DEPCA_ADDR  ioaddr+0x06   /* LANCE registers' address port */
-#define DEPCA_HBASE ioaddr+0x08   /* EISA high memory base address reg. */
-#define DEPCA_PROM  ioaddr+0x0c   /* Ethernet address ROM data port */
-#define DEPCA_CNFG  ioaddr+0x0c   /* EISA Configuration port */
-#define DEPCA_RBSA  ioaddr+0x0e   /* RAM buffer starting address (2k buff.) */
-
-/*
-** These are LANCE registers addressable through DEPCA_ADDR
-*/
-#define CSR0       0
-#define CSR1       1
-#define CSR2       2
-#define CSR3       3
-
-/*
-** NETWORK INTERFACE CSR (NI_CSR) bit definitions
-*/
-
-#define TO       	0x0100	/* Time Out for remote boot */
-#define SHE      	0x0080  /* SHadow memory Enable */
-#define BS       	0x0040  /* Bank Select */
-#define BUF      	0x0020	/* BUFfer size (1->32k, 0->64k) */
-#define RBE      	0x0010	/* Remote Boot Enable (1->net boot) */
-#define AAC      	0x0008  /* Address ROM Address Counter (1->enable) */
-#define _128KB      	0x0008  /* 128kB Network RAM (1->enable) */
-#define IM       	0x0004	/* Interrupt Mask (1->mask) */
-#define IEN      	0x0002	/* Interrupt tristate ENable (1->enable) */
-#define LED      	0x0001	/* LED control */
-
-/*
-** Control and Status Register 0 (CSR0) bit definitions
-*/
-
-#define ERR     	0x8000 	/* Error summary */
-#define BABL    	0x4000 	/* Babble transmitter timeout error  */
-#define CERR    	0x2000 	/* Collision Error */
-#define MISS    	0x1000 	/* Missed packet */
-#define MERR    	0x0800 	/* Memory Error */
-#define RINT    	0x0400 	/* Receiver Interrupt */
-#define TINT    	0x0200 	/* Transmit Interrupt */
-#define IDON    	0x0100 	/* Initialization Done */
-#define INTR    	0x0080 	/* Interrupt Flag */
-#define INEA    	0x0040 	/* Interrupt Enable */
-#define RXON    	0x0020 	/* Receiver on */
-#define TXON    	0x0010 	/* Transmitter on */
-#define TDMD    	0x0008 	/* Transmit Demand */
-#define STOP    	0x0004 	/* Stop */
-#define STRT    	0x0002 	/* Start */
-#define INIT    	0x0001 	/* Initialize */
-#define INTM            0xff00  /* Interrupt Mask */
-#define INTE            0xfff0  /* Interrupt Enable */
-
-/*
-** CONTROL AND STATUS REGISTER 3 (CSR3)
-*/
-
-#define BSWP    	0x0004	/* Byte SWaP */
-#define ACON    	0x0002	/* ALE control */
-#define BCON    	0x0001	/* Byte CONtrol */
-
-/*
-** Initialization Block Mode Register
-*/
-
-#define PROM       	0x8000 	/* Promiscuous Mode */
-#define EMBA       	0x0080	/* Enable Modified Back-off Algorithm */
-#define INTL       	0x0040 	/* Internal Loopback */
-#define DRTY       	0x0020 	/* Disable Retry */
-#define COLL       	0x0010 	/* Force Collision */
-#define DTCR       	0x0008 	/* Disable Transmit CRC */
-#define LOOP       	0x0004 	/* Loopback */
-#define DTX        	0x0002 	/* Disable the Transmitter */
-#define DRX        	0x0001 	/* Disable the Receiver */
-
-/*
-** Receive Message Descriptor 1 (RMD1) bit definitions.
-*/
-
-#define R_OWN       0x80000000 	/* Owner bit 0 = host, 1 = lance */
-#define R_ERR     	0x4000 	/* Error Summary */
-#define R_FRAM    	0x2000 	/* Framing Error */
-#define R_OFLO    	0x1000 	/* Overflow Error */
-#define R_CRC     	0x0800 	/* CRC Error */
-#define R_BUFF    	0x0400 	/* Buffer Error */
-#define R_STP     	0x0200 	/* Start of Packet */
-#define R_ENP     	0x0100 	/* End of Packet */
-
-/*
-** Transmit Message Descriptor 1 (TMD1) bit definitions.
-*/
-
-#define T_OWN       0x80000000 	/* Owner bit 0 = host, 1 = lance */
-#define T_ERR     	0x4000 	/* Error Summary */
-#define T_ADD_FCS 	0x2000 	/* More the 1 retry needed to Xmit */
-#define T_MORE    	0x1000	/* >1 retry to transmit packet */
-#define T_ONE     	0x0800 	/* 1 try needed to transmit the packet */
-#define T_DEF     	0x0400 	/* Deferred */
-#define T_STP       0x02000000 	/* Start of Packet */
-#define T_ENP       0x01000000	/* End of Packet */
-#define T_FLAGS     0xff000000  /* TX Flags Field */
-
-/*
-** Transmit Message Descriptor 3 (TMD3) bit definitions.
-*/
-
-#define TMD3_BUFF    0x8000	/* BUFFer error */
-#define TMD3_UFLO    0x4000	/* UnderFLOw error */
-#define TMD3_RES     0x2000	/* REServed */
-#define TMD3_LCOL    0x1000	/* Late COLlision */
-#define TMD3_LCAR    0x0800	/* Loss of CARrier */
-#define TMD3_RTRY    0x0400	/* ReTRY error */
-
-/*
-** EISA configuration Register (CNFG) bit definitions
-*/
-
-#define TIMEOUT       	0x0100	/* 0:2.5 mins, 1: 30 secs */
-#define REMOTE      	0x0080  /* Remote Boot Enable -> 1 */
-#define IRQ11       	0x0040  /* Enable -> 1 */
-#define IRQ10    	0x0020	/* Enable -> 1 */
-#define IRQ9    	0x0010	/* Enable -> 1 */
-#define IRQ5      	0x0008  /* Enable -> 1 */
-#define BUFF     	0x0004	/* 0: 64kB or 128kB, 1: 32kB */
-#define PADR16   	0x0002	/* RAM on 64kB boundary */
-#define PADR17    	0x0001	/* RAM on 128kB boundary */
-
-/*
-** Miscellaneous
-*/
-#define HASH_TABLE_LEN   64           /* Bits */
-#define HASH_BITS        0x003f       /* 6 LS bits */
-
-#define MASK_INTERRUPTS   1
-#define UNMASK_INTERRUPTS 0
-
-#define EISA_EN         0x0001        /* Enable EISA bus buffers */
-#define EISA_ID         iobase+0x0080 /* ID long word for EISA card */
-#define EISA_CTRL       iobase+0x0084 /* Control word for EISA card */
-
-/*
-** Include the IOCTL stuff
-*/
-#include <linux/sockios.h>
-
-struct depca_ioctl {
-	unsigned short cmd;                /* Command to run */
-	unsigned short len;                /* Length of the data buffer */
-	unsigned char  __user *data;       /* Pointer to the data buffer */
-};
-
-/*
-** Recognised commands for the driver
-*/
-#define DEPCA_GET_HWADDR	0x01 /* Get the hardware address */
-#define DEPCA_SET_HWADDR	0x02 /* Get the hardware address */
-#define DEPCA_SET_PROM  	0x03 /* Set Promiscuous Mode */
-#define DEPCA_CLR_PROM  	0x04 /* Clear Promiscuous Mode */
-#define DEPCA_SAY_BOO	        0x05 /* Say "Boo!" to the kernel log file */
-#define DEPCA_GET_MCA   	0x06 /* Get a multicast address */
-#define DEPCA_SET_MCA   	0x07 /* Set a multicast address */
-#define DEPCA_CLR_MCA    	0x08 /* Clear a multicast address */
-#define DEPCA_MCA_EN    	0x09 /* Enable a multicast address group */
-#define DEPCA_GET_STATS  	0x0a /* Get the driver statistics */
-#define DEPCA_CLR_STATS 	0x0b /* Zero out the driver statistics */
-#define DEPCA_GET_REG   	0x0c /* Get the Register contents */
-#define DEPCA_SET_REG   	0x0d /* Set the Register contents */
-#define DEPCA_DUMP              0x0f /* Dump the DEPCA Status */
-