Merge tag 'riscv-dt-for-v6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt

RISC-V Misc Devicetrees for v6.18

Starfive:
The main new addition is support for the JH7110 Milk-V Mars CM lite SoM.
Other than that, there's several cleanups done to the common JH7110 dtsi
file, some relating to properties used by U-Boot or encountered during
U-Boot development. Additionally, there's a binding and devicetree node
for the memory controller on the JH7110. The memory controller only sees
use in U-Boot, so the binding is here rather than in Krzysztof's
branch.

SiFive:
Support for SiFive vendor-specific extensions in the binding file for
extensions. These currently only see use in the SBI implementation.

Microchip:
Addition of support for the PolarFire SoC Discovery kit and
non-engineering sample Icicle kit. The latter differs very slightly from
the final ES devices due to bug fixes affecting functionality, and needs
its own dts. To reduce duplication, the common portion of the two Icicle
kits are moved into a dtsi. There's a few minor fixes here too, mostly
low-hanging fruit detected during the addition of the Discovery kit that
were then applied to the Icicle.

Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

* tag 'riscv-dt-for-v6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
  riscv: dts: starfive: add Milk-V Mars CM Lite system-on-module
  dt-bindings: riscv: starfive: add milkv,marscm-lite
  riscv: dts: starfive: add Milk-V Mars CM system-on-module
  dt-bindings: riscv: starfive: add milkv,marscm-emmc
  riscv: dts: starfive: add common board dtsi for Milk-V Mars CM variants
  riscv: dts: microchip: add a device tree for Discovery Kit
  dt-bindings: riscv: microchip: document Discovery Kit
  riscv: dts: microchip: rename icicle kit ccc clock and other minor fixes
  riscv: dts: microchip: add icicle kit with production device
  dt-bindings: riscv: microchip: document icicle kit with production device
  riscv: dts: microchip: add common board dtsi for icicle kit variants
  riscv: dts: starfive: jh7110-common: drop mmc post-power-on-delay-ms
  riscv: dts: starfive: jh7110-common: drop no-mmc property from mmc1
  riscv: dts: starfive: jh7110: bootph-pre-ram hinting needed by boot loader
  riscv: dts: starfive: jh7110: add DMC memory controller
  dt-bindings: memory-controllers: add StarFive JH7110 SoC DMC
  riscv: dts: starfive: jh7110-common: drop no-sdio property from mmc1
  riscv: dts: microchip: Minor whitespace cleanup
  dt-bindings: riscv: Add SiFive vendor extensions description

Link: https://lore.kernel.org/r/20250924-frighten-magazine-ee2f16e64638@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

18 files changed, 876 insertions, 250 deletions

diff --git a/Documentation/devicetree/bindings/memory-controllers/starfive,jh7110-dmc.yaml b/Documentation/devicetree/bindings/memory-controllers/starfive,jh7110-dmc.yaml
new file mode 100644
index 000000000000..d65313b33a3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/starfive,jh7110-dmc.yaml
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/starfive,jh7110-dmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 DMC
+
+maintainers:
+  - E Shattow <e@freeshell.de>
+
+description:
+  JH7110 DDR external memory interface LPDDR4/DDR4/DDR3/LPDDR3 32-bit at
+  2133Mbps (up to 2800Mbps).
+
+properties:
+  compatible:
+    items:
+      - const: starfive,jh7110-dmc
+
+  reg:
+    items:
+      - description: controller registers
+      - description: phy registers
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: pll
+
+  resets:
+    items:
+      - description: axi
+      - description: osc
+      - description: apb
+
+  reset-names:
+    items:
+      - const: axi
+      - const: osc
+      - const: apb
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/starfive,jh7110-crg.h>
+    #include <dt-bindings/reset/starfive,jh7110-crg.h>
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      memory-controller@15700000 {
+        compatible = "starfive,jh7110-dmc";
+        reg = <0x0 0x15700000 0x0 0x10000>,
+              <0x0 0x13000000 0x0 0x10000>;
+        clocks = <&syscrg JH7110_PLLCLK_PLL1_OUT>;
+        clock-names = "pll";
+        resets = <&syscrg JH7110_SYSRST_DDR_AXI>,
+                 <&syscrg JH7110_SYSRST_DDR_OSC>,
+                 <&syscrg JH7110_SYSRST_DDR_APB>;
+        reset-names = "axi", "osc", "apb";
+      };
+    };
diff --git a/Documentation/devicetree/bindings/riscv/extensions.yaml b/Documentation/devicetree/bindings/riscv/extensions.yaml
index ede6a58ccf53..5638297759df 100644
--- a/Documentation/devicetree/bindings/riscv/extensions.yaml
+++ b/Documentation/devicetree/bindings/riscv/extensions.yaml
@@ -663,6 +663,24 @@ properties:
             https://www.andestech.com/wp-content/uploads/AX45MP-1C-Rev.-5.0.0-Datasheet.pdf
 
         # SiFive
+        - const: xsfcease
+          description:
+            SiFive CEASE Instruction Extensions Specification.
+            See more details in
+            https://www.sifive.com/document-file/freedom-u740-c000-manual
+
+        - const: xsfcflushdlone
+          description:
+            SiFive L1D Cache Flush Instruction Extensions Specification.
+            See more details in
+            https://www.sifive.com/document-file/freedom-u740-c000-manual
+
+        - const: xsfpgflushdlone
+          description:
+            SiFive PGFLUSH Instruction Extensions for the power management. The
+            CPU will flush the L1D and enter the cease state after executing
+            the instruction.
+
         - const: xsfvqmaccdod
           description:
             SiFive Int8 Matrix Multiplication Extensions Specification.
diff --git a/Documentation/devicetree/bindings/riscv/microchip.yaml b/Documentation/devicetree/bindings/riscv/microchip.yaml
index 78ce76ae1b6d..381d6eb6672e 100644
--- a/Documentation/devicetree/bindings/riscv/microchip.yaml
+++ b/Documentation/devicetree/bindings/riscv/microchip.yaml
@@ -19,13 +19,26 @@ properties:
   compatible:
     oneOf:
       - items:
+          - const: microchip,mpfs-icicle-prod-reference-rtl-v2507
+          - const: microchip,mpfs-icicle-kit-prod
+          - const: microchip,mpfs-icicle-kit
+          - const: microchip,mpfs-prod
+          - const: microchip,mpfs
+
+      - items:
           - enum:
               - microchip,mpfs-icicle-reference-rtlv2203
               - microchip,mpfs-icicle-reference-rtlv2210
+              - microchip,mpfs-icicle-es-reference-rtl-v2507
           - const: microchip,mpfs-icicle-kit
           - const: microchip,mpfs
 
       - items:
+          - const: microchip,mpfs-disco-kit-reference-rtl-v2507
+          - const: microchip,mpfs-disco-kit
+          - const: microchip,mpfs
+
+      - items:
           - enum:
               - aldec,tysom-m-mpfs250t-rev2
               - aries,m100pfsevp
diff --git a/Documentation/devicetree/bindings/riscv/starfive.yaml b/Documentation/devicetree/bindings/riscv/starfive.yaml
index 7ef85174353d..04510341a71e 100644
--- a/Documentation/devicetree/bindings/riscv/starfive.yaml
+++ b/Documentation/devicetree/bindings/riscv/starfive.yaml
@@ -28,6 +28,8 @@ properties:
           - enum:
               - deepcomputing,fml13v01
               - milkv,mars
+              - milkv,marscm-emmc
+              - milkv,marscm-lite
               - pine64,star64
               - starfive,visionfive-2-v1.2a
               - starfive,visionfive-2-v1.3b
diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
index f51aeeb9fd3b..345ed7a48cc1 100644
--- a/arch/riscv/boot/dts/microchip/Makefile
+++ b/arch/riscv/boot/dts/microchip/Makefile
@@ -1,6 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-beaglev-fire.dtb
+dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-disco-kit.dtb
 dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-icicle-kit.dtb
+dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-icicle-kit-prod.dtb
 dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-m100pfsevp.dtb
 dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-polarberry.dtb
 dtb-$(CONFIG_ARCH_MICROCHIP_POLARFIRE) += mpfs-sev-kit.dtb
diff --git a/arch/riscv/boot/dts/microchip/mpfs-beaglev-fire.dts b/arch/riscv/boot/dts/microchip/mpfs-beaglev-fire.dts
index 47cf693beb68..55e30f3636df 100644
--- a/arch/riscv/boot/dts/microchip/mpfs-beaglev-fire.dts
+++ b/arch/riscv/boot/dts/microchip/mpfs-beaglev-fire.dts
@@ -88,7 +88,7 @@
 		     <53>, <53>, <53>, <53>,
 		     <53>, <53>, <53>, <53>,
 		     <53>, <53>, <53>, <53>;
-	ngpios=<32>;
+	ngpios = <32>;
 	gpio-line-names = "P8_PIN3_USER_LED_0", "P8_PIN4_USER_LED_1", "P8_PIN5_USER_LED_2",
 			  "P8_PIN6_USER_LED_3", "P8_PIN7_USER_LED_4", "P8_PIN8_USER_LED_5",
 			  "P8_PIN9_USER_LED_6", "P8_PIN10_USER_LED_7", "P8_PIN11_USER_LED_8",
diff --git a/arch/riscv/boot/dts/microchip/mpfs-disco-kit-fabric.dtsi b/arch/riscv/boot/dts/microchip/mpfs-disco-kit-fabric.dtsi
new file mode 100644
index 000000000000..ae8be7d6f392
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/mpfs-disco-kit-fabric.dtsi
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2020-2025 Microchip Technology Inc */
+
+/ {
+	core_pwm0: pwm@40000000 {
+		compatible = "microchip,corepwm-rtl-v4";
+		reg = <0x0 0x40000000 0x0 0xF0>;
+		microchip,sync-update-mask = /bits/ 32 <0>;
+		#pwm-cells = <3>;
+		clocks = <&ccc_sw CLK_CCC_PLL0_OUT3>;
+		status = "disabled";
+	};
+
+	i2c2: i2c@40000200 {
+		compatible = "microchip,corei2c-rtl-v7";
+		reg = <0x0 0x40000200 0x0 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&ccc_sw CLK_CCC_PLL0_OUT3>;
+		interrupt-parent = <&plic>;
+		interrupts = <122>;
+		clock-frequency = <100000>;
+		status = "disabled";
+	};
+
+	ihc: mailbox {
+		compatible = "microchip,sbi-ipc";
+		interrupt-parent = <&plic>;
+		interrupts = <180>, <179>, <178>, <177>;
+		interrupt-names = "hart-1", "hart-2", "hart-3", "hart-4";
+		#mbox-cells = <1>;
+		status = "disabled";
+	};
+
+	mailbox@50000000 {
+		compatible = "microchip,miv-ihc-rtl-v2";
+		reg = <0x0 0x50000000 0x0 0x1c000>;
+		interrupt-parent = <&plic>;
+		interrupts = <180>, <179>, <178>, <177>;
+		interrupt-names = "hart-1", "hart-2", "hart-3", "hart-4";
+		#mbox-cells = <1>;
+		microchip,ihc-chan-disabled-mask = /bits/ 16 <0>;
+		status = "disabled";
+	};
+
+	refclk_ccc: clock-cccref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+};
+
+&ccc_sw {
+	clocks = <&refclk_ccc>, <&refclk_ccc>, <&refclk_ccc>, <&refclk_ccc>,
+		 <&refclk_ccc>, <&refclk_ccc>;
+	clock-names = "pll0_ref0", "pll0_ref1", "pll1_ref0", "pll1_ref1",
+		      "dll0_ref", "dll1_ref";
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/microchip/mpfs-disco-kit.dts b/arch/riscv/boot/dts/microchip/mpfs-disco-kit.dts
new file mode 100644
index 000000000000..c068b9bb5bfd
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/mpfs-disco-kit.dts
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2020-2025 Microchip Technology Inc */
+
+/dts-v1/;
+
+#include "mpfs.dtsi"
+#include "mpfs-disco-kit-fabric.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Microchip PolarFire-SoC Discovery Kit";
+	compatible = "microchip,mpfs-disco-kit-reference-rtl-v2507",
+		     "microchip,mpfs-disco-kit",
+		     "microchip,mpfs";
+
+	aliases {
+		ethernet0 = &mac0;
+		serial4 = &mmuart4;
+	};
+
+	chosen {
+		stdout-path = "serial4:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-1 {
+			gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_AMBER>;
+			label = "led1";
+		};
+
+		led-2 {
+			gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+			label = "led2";
+		};
+
+		led-3 {
+			gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_AMBER>;
+			label = "led3";
+		};
+
+		led-4 {
+			gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+			label = "led4";
+		};
+
+		led-5 {
+			gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_AMBER>;
+			label = "led5";
+		};
+
+		led-6 {
+			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+			label = "led6";
+		};
+
+		led-7 {
+			gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_AMBER>;
+			label = "led7";
+		};
+
+		led-8 {
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+			label = "led8";
+		};
+	};
+
+	ddrc_cache_lo: memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hss_payload: region@bfc00000 {
+			reg = <0x0 0xbfc00000 0x0 0x400000>;
+			no-map;
+		};
+	};
+};
+
+&core_pwm0 {
+	status = "okay";
+};
+
+&gpio1 {
+	interrupts = <27>, <28>, <29>, <30>,
+		     <31>, <32>, <33>, <47>,
+		     <35>, <36>, <37>, <38>,
+		     <39>, <40>, <41>, <42>,
+		     <43>, <44>, <45>, <46>,
+		     <47>, <48>, <49>, <50>;
+	status = "okay";
+};
+
+&gpio2 {
+	interrupts = <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&ihc {
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "sgmii";
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy@b {
+		reg = <0xb>;
+	};
+};
+
+&mbox {
+	status = "okay";
+};
+
+&mmc {
+	bus-width = <4>;
+	disable-wp;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	no-1-8-v;
+	status = "okay";
+};
+
+&mmuart1 {
+	status = "okay";
+};
+
+&mmuart4 {
+	status = "okay";
+};
+
+&refclk {
+	clock-frequency = <125000000>;
+};
+
+&refclk_ccc {
+	clock-frequency = <50000000>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+};
+
+&syscontroller {
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-common.dtsi b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-common.dtsi
new file mode 100644
index 000000000000..e01a216e6c3a
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-common.dtsi
@@ -0,0 +1,249 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2025 Microchip Technology Inc */
+
+/dts-v1/;
+
+#include "mpfs.dtsi"
+#include "mpfs-icicle-kit-fabric.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		ethernet0 = &mac1;
+		serial0 = &mmuart0;
+		serial1 = &mmuart1;
+		serial2 = &mmuart2;
+		serial3 = &mmuart3;
+		serial4 = &mmuart4;
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-1 {
+			gpios = <&gpio2 16 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+			label = "led1";
+		};
+
+		led-2 {
+			gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+			label = "led2";
+		};
+
+		led-3 {
+			gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_AMBER>;
+			label = "led3";
+		};
+
+		led-4 {
+			gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_AMBER>;
+			label = "led4";
+		};
+	};
+
+	ddrc_cache_lo: memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x40000000>;
+	};
+
+	ddrc_cache_hi: memory@1040000000 {
+		device_type = "memory";
+		reg = <0x10 0x40000000 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hss_payload: region@bfc00000 {
+			reg = <0x0 0xbfc00000 0x0 0x400000>;
+			no-map;
+		};
+	};
+};
+
+&core_pwm0 {
+	status = "okay";
+};
+
+&gpio2 {
+	interrupts = <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>,
+		     <53>, <53>, <53>, <53>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	power-monitor@10 {
+		compatible = "microchip,pac1934";
+		reg = <0x10>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <0x1>;
+			shunt-resistor-micro-ohms = <10000>;
+			label = "VDDREG";
+		};
+
+		channel@2 {
+			reg = <0x2>;
+			shunt-resistor-micro-ohms = <10000>;
+			label = "VDDA25";
+		};
+
+		channel@3 {
+			reg = <0x3>;
+			shunt-resistor-micro-ohms = <10000>;
+			label = "VDD25";
+		};
+
+		channel@4 {
+			reg = <0x4>;
+			shunt-resistor-micro-ohms = <10000>;
+			label = "VDDA_REG";
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&ihc {
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "sgmii";
+	phy-handle = <&phy0>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "sgmii";
+	phy-handle = <&phy1>;
+	status = "okay";
+
+	phy1: ethernet-phy@9 {
+		reg = <9>;
+	};
+
+	phy0: ethernet-phy@8 {
+		reg = <8>;
+	};
+};
+
+&mbox {
+	status = "okay";
+};
+
+&mmc {
+	bus-width = <4>;
+	disable-wp;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&mmuart1 {
+	status = "okay";
+};
+
+&mmuart2 {
+	status = "okay";
+};
+
+&mmuart3 {
+	status = "okay";
+};
+
+&mmuart4 {
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+};
+
+&refclk {
+	clock-frequency = <125000000>;
+};
+
+&refclk_ccc {
+	clock-frequency = <50000000>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+};
+
+&syscontroller {
+	status = "okay";
+};
+
+&syscontroller_qspi {
+	/*
+	 * The flash *is* there, but Icicle kits that have engineering sample
+	 * silicon (write?) access to this flash to non-functional. The system
+	 * controller itself can actually access it, but the MSS cannot write
+	 * an image there. Instantiating a coreQSPI in the fabric & connecting
+	 * it to the flash instead should work though. Pre-production or later
+	 * silicon does not have this issue.
+	 */
+	status = "disabled";
+
+	sys_ctrl_flash: flash@0 { // MT25QL01GBBB8ESF-0SIT
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <20000000>;
+		spi-rx-bus-width = <1>;
+		reg = <0>;
+	};
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "host";
+};
diff --git a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
index a6dda55a2d1d..71f724325578 100644
--- a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
+++ b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
@@ -2,9 +2,6 @@
 /* Copyright (c) 2020-2021 Microchip Technology Inc */
 
 / {
-	compatible = "microchip,mpfs-icicle-reference-rtlv2210", "microchip,mpfs-icicle-kit",
-		     "microchip,mpfs";
-
 	core_pwm0: pwm@40000000 {
 		compatible = "microchip,corepwm-rtl-v4";
 		reg = <0x0 0x40000000 0x0 0xF0>;
@@ -26,6 +23,26 @@
 		status = "disabled";
 	};
 
+	ihc: mailbox {
+		compatible = "microchip,sbi-ipc";
+		interrupt-parent = <&plic>;
+		interrupts = <180>, <179>, <178>, <177>;
+		interrupt-names = "hart-1", "hart-2", "hart-3", "hart-4";
+		#mbox-cells = <1>;
+		status = "disabled";
+	};
+
+	mailbox@50000000 {
+		compatible = "microchip,miv-ihc-rtl-v2";
+		reg = <0x0 0x50000000 0x0 0x1c000>;
+		interrupt-parent = <&plic>;
+		interrupts = <180>, <179>, <178>, <177>;
+		interrupt-names = "hart-1", "hart-2", "hart-3", "hart-4";
+		#mbox-cells = <1>;
+		microchip,ihc-chan-disabled-mask = /bits/ 16 <0>;
+		status = "disabled";
+	};
+
 	pcie: pcie@3000000000 {
 		compatible = "microchip,pcie-host-1.0";
 		#address-cells = <0x3>;
@@ -57,7 +74,7 @@
 		};
 	};
 
-	refclk_ccc: cccrefclk {
+	refclk_ccc: clock-cccref {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 	};
diff --git a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-prod.dts b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-prod.dts
new file mode 100644
index 000000000000..8afedece89d1
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-prod.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2025 Microchip Technology Inc */
+
+/dts-v1/;
+
+#include "mpfs-icicle-kit-common.dtsi"
+
+/ {
+	model = "Microchip PolarFire-SoC Icicle Kit (Production Silicon)";
+	compatible = "microchip,mpfs-icicle-prod-reference-rtl-v2507",
+		     "microchip,mpfs-icicle-kit-prod",
+		     "microchip,mpfs-icicle-kit",
+		     "microchip,mpfs-prod",
+		     "microchip,mpfs";
+};
+
+&syscontroller {
+	microchip,bitstream-flash = <&sys_ctrl_flash>;
+};
+
+&syscontroller_qspi {
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts
index f80df225f72b..556aa9638282 100644
--- a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts
+++ b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts
@@ -3,249 +3,11 @@
 
 /dts-v1/;
 
-#include "mpfs.dtsi"
-#include "mpfs-icicle-kit-fabric.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/leds/common.h>
+#include "mpfs-icicle-kit-common.dtsi"
 
 / {
 	model = "Microchip PolarFire-SoC Icicle Kit";
-	compatible = "microchip,mpfs-icicle-reference-rtlv2210", "microchip,mpfs-icicle-kit",
+	compatible = "microchip,mpfs-icicle-es-reference-rtl-v2507",
+		     "microchip,mpfs-icicle-kit",
 		     "microchip,mpfs";
-
-	aliases {
-		ethernet0 = &mac1;
-		serial0 = &mmuart0;
-		serial1 = &mmuart1;
-		serial2 = &mmuart2;
-		serial3 = &mmuart3;
-		serial4 = &mmuart4;
-	};
-
-	chosen {
-		stdout-path = "serial1:115200n8";
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led-1 {
-			gpios = <&gpio2 16 GPIO_ACTIVE_HIGH>;
-			color = <LED_COLOR_ID_RED>;
-			label = "led1";
-		};
-
-		led-2 {
-			gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
-			color = <LED_COLOR_ID_RED>;
-			label = "led2";
-		};
-
-		led-3 {
-			gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
-			color = <LED_COLOR_ID_AMBER>;
-			label = "led3";
-		};
-
-		led-4 {
-			gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>;
-			color = <LED_COLOR_ID_AMBER>;
-			label = "led4";
-		};
-	};
-
-	ddrc_cache_lo: memory@80000000 {
-		device_type = "memory";
-		reg = <0x0 0x80000000 0x0 0x40000000>;
-		status = "okay";
-	};
-
-	ddrc_cache_hi: memory@1040000000 {
-		device_type = "memory";
-		reg = <0x10 0x40000000 0x0 0x40000000>;
-		status = "okay";
-	};
-
-	reserved-memory {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		hss_payload: region@BFC00000 {
-			reg = <0x0 0xBFC00000 0x0 0x400000>;
-			no-map;
-		};
-	};
-};
-
-&core_pwm0 {
-	status = "okay";
-};
-
-&gpio2 {
-	interrupts = <53>, <53>, <53>, <53>,
-		     <53>, <53>, <53>, <53>,
-		     <53>, <53>, <53>, <53>,
-		     <53>, <53>, <53>, <53>,
-		     <53>, <53>, <53>, <53>,
-		     <53>, <53>, <53>, <53>,
-		     <53>, <53>, <53>, <53>,
-		     <53>, <53>, <53>, <53>;
-	status = "okay";
-};
-
-&i2c0 {
-	status = "okay";
-};
-
-&i2c1 {
-	status = "okay";
-
-	power-monitor@10 {
-		compatible = "microchip,pac1934";
-		reg = <0x10>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		channel@1 {
-			reg = <0x1>;
-			shunt-resistor-micro-ohms = <10000>;
-			label = "VDDREG";
-		};
-
-		channel@2 {
-			reg = <0x2>;
-			shunt-resistor-micro-ohms = <10000>;
-			label = "VDDA25";
-		};
-
-		channel@3 {
-			reg = <0x3>;
-			shunt-resistor-micro-ohms = <10000>;
-			label = "VDD25";
-		};
-
-		channel@4 {
-			reg = <0x4>;
-			shunt-resistor-micro-ohms = <10000>;
-			label = "VDDA_REG";
-		};
-	};
-};
-
-&i2c2 {
-	status = "okay";
-};
-
-&mac0 {
-	phy-mode = "sgmii";
-	phy-handle = <&phy0>;
-	status = "okay";
-};
-
-&mac1 {
-	phy-mode = "sgmii";
-	phy-handle = <&phy1>;
-	status = "okay";
-
-	phy1: ethernet-phy@9 {
-		reg = <9>;
-	};
-
-	phy0: ethernet-phy@8 {
-		reg = <8>;
-	};
-};
-
-&mbox {
-	status = "okay";
-};
-
-&mmc {
-	bus-width = <4>;
-	disable-wp;
-	cap-sd-highspeed;
-	cap-mmc-highspeed;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-	status = "okay";
-};
-
-&mmuart1 {
-	status = "okay";
-};
-
-&mmuart2 {
-	status = "okay";
-};
-
-&mmuart3 {
-	status = "okay";
-};
-
-&mmuart4 {
-	status = "okay";
-};
-
-&pcie {
-	status = "okay";
-};
-
-&qspi {
-	status = "okay";
-};
-
-&refclk {
-	clock-frequency = <125000000>;
-};
-
-&refclk_ccc {
-	clock-frequency = <50000000>;
-};
-
-&rtc {
-	status = "okay";
-};
-
-&spi0 {
-	status = "okay";
-};
-
-&spi1 {
-	status = "okay";
-};
-
-&syscontroller {
-	status = "okay";
-};
-
-&syscontroller_qspi {
-	/*
-	 * The flash *is* there, but Icicle kits that have engineering sample
-	 * silicon (write?) access to this flash to non-functional. The system
-	 * controller itself can actually access it, but the MSS cannot write
-	 * an image there. Instantiating a coreQSPI in the fabric & connecting
-	 * it to the flash instead should work though. Pre-production or later
-	 * silicon does not have this issue.
-	 */
-	status = "disabled";
-
-	sys_ctrl_flash: flash@0 { // MT25QL01GBBB8ESF-0SIT
-		compatible = "jedec,spi-nor";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		spi-max-frequency = <20000000>;
-		spi-rx-bus-width = <1>;
-		reg = <0>;
-	};
-};
-
-&usb {
-	status = "okay";
-	dr_mode = "host";
 };
diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile
index b3bb12f78e7d..62b659f89ba7 100644
--- a/arch/riscv/boot/dts/starfive/Makefile
+++ b/arch/riscv/boot/dts/starfive/Makefile
@@ -10,6 +10,8 @@ dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-starfive-visionfive-v1.dtb
 
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-deepcomputing-fml13v01.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-mars.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-emmc.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-lite.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-pine64-star64.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb
diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
index 2eaf01775ef5..5dc15e48b74b 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
@@ -285,7 +285,6 @@
 	mmc-ddr-1_8v;
 	mmc-hs200-1_8v;
 	cap-mmc-hw-reset;
-	post-power-on-delay-ms = <200>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&vcc_3v3>;
@@ -299,12 +298,9 @@
 	assigned-clock-rates = <50000000>;
 	bus-width = <4>;
 	bootph-pre-ram;
-	no-sdio;
-	no-mmc;
 	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	cap-sd-highspeed;
-	post-power-on-delay-ms = <200>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
 	status = "okay";
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts
new file mode 100644
index 000000000000..e568537af2c4
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 E Shattow <e@freeshell.de>
+ */
+
+/dts-v1/;
+#include "jh7110-milkv-marscm.dtsi"
+
+/ {
+	model = "Milk-V Mars CM";
+	compatible = "milkv,marscm-emmc", "starfive,jh7110";
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
new file mode 100644
index 000000000000..6c40d0ec4011
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 E Shattow <e@freeshell.de>
+ */
+
+/dts-v1/;
+#include "jh7110-milkv-marscm.dtsi"
+
+/ {
+	model = "Milk-V Mars CM Lite";
+	compatible = "milkv,marscm-lite", "starfive,jh7110";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+};
+
+&mmc0_pins {
+	pwren-pins {
+		pinmux = <GPIOMUX(22, GPOUT_HIGH,
+				      GPOEN_ENABLE,
+				      GPI_NONE)>;
+	};
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi
new file mode 100644
index 000000000000..25b70af564ee
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 E Shattow <e@freeshell.de>
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "jh7110-common.dtsi"
+
+/ {
+	aliases {
+		i2c1 = &i2c1;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		serial3 = &uart3;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&sysgpio 33 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&gmac0 {
+	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
+	assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
+	starfive,tx-use-rgmii-clk;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "disabled";
+};
+
+&i2c6 {
+	status = "disabled";
+};
+
+&mmc1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	status = "okay";
+
+	ap6256: wifi@1 {
+		compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+		interrupt-parent = <&sysgpio>;
+		interrupts = <34 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+		pinctrl-0 = <&wifi_host_wake_irq>;
+		pinctrl-names = "default";
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&phy0 {
+	rx-internal-delay-ps = <1500>;
+	tx-internal-delay-ps = <1500>;
+	motorcomm,rx-clk-drv-microamp = <3970>;
+	motorcomm,rx-data-drv-microamp = <2910>;
+	motorcomm,tx-clk-10-inverted;
+	motorcomm,tx-clk-100-inverted;
+	motorcomm,tx-clk-1000-inverted;
+	motorcomm,tx-clk-adj-enabled;
+};
+
+&pwm {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+};
+
+&sysgpio {
+	uart1_pins: uart1-0 {
+		tx-pins {
+			pinmux = <GPIOMUX(16, GPOUT_SYS_UART1_TX,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-disable;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+		};
+
+		rx-pins {
+			pinmux = <GPIOMUX(17, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_UART1_RX)>;
+			bias-pull-up;
+			input-enable;
+			input-schmitt-enable;
+		};
+
+		cts-pins {
+			pinmux = <GPIOMUX(3, GPOUT_LOW,
+					     GPOEN_DISABLE,
+					     GPI_SYS_UART1_CTS)>;
+			bias-disable;
+			input-enable;
+			input-schmitt-enable;
+		};
+
+		rts-pins {
+			pinmux = <GPIOMUX(2, GPOUT_SYS_UART1_RTS,
+					     GPOEN_ENABLE,
+					     GPI_NONE)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+		};
+	};
+
+	usb0_pins: usb0-0 {
+		vbus-pins {
+			pinmux = <GPIOMUX(25, GPOUT_SYS_USB_DRIVE_VBUS,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
+	wifi_host_wake_irq: wifi-host-wake-irq-0 {
+		wake-pins {
+			pinmux = <GPIOMUX(34, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_NONE)>;
+			input-enable;
+		};
+	};
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins>;
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 0ba74ef04679..6e56e9d20bb0 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -35,6 +35,7 @@
 
 			cpu0_intc: interrupt-controller {
 				compatible = "riscv,cpu-intc";
+				bootph-pre-ram;
 				interrupt-controller;
 				#interrupt-cells = <1>;
 			};
@@ -68,6 +69,7 @@
 
 			cpu1_intc: interrupt-controller {
 				compatible = "riscv,cpu-intc";
+				bootph-pre-ram;
 				interrupt-controller;
 				#interrupt-cells = <1>;
 			};
@@ -101,6 +103,7 @@
 
 			cpu2_intc: interrupt-controller {
 				compatible = "riscv,cpu-intc";
+				bootph-pre-ram;
 				interrupt-controller;
 				#interrupt-cells = <1>;
 			};
@@ -134,6 +137,7 @@
 
 			cpu3_intc: interrupt-controller {
 				compatible = "riscv,cpu-intc";
+				bootph-pre-ram;
 				interrupt-controller;
 				#interrupt-cells = <1>;
 			};
@@ -167,6 +171,7 @@
 
 			cpu4_intc: interrupt-controller {
 				compatible = "riscv,cpu-intc";
+				bootph-pre-ram;
 				interrupt-controller;
 				#interrupt-cells = <1>;
 			};
@@ -273,12 +278,14 @@
 
 	gmac1_rgmii_rxin: gmac1-rgmii-rxin-clock {
 		compatible = "fixed-clock";
+		bootph-pre-ram;
 		clock-output-names = "gmac1_rgmii_rxin";
 		#clock-cells = <0>;
 	};
 
 	gmac1_rmii_refin: gmac1-rmii-refin-clock {
 		compatible = "fixed-clock";
+		bootph-pre-ram;
 		clock-output-names = "gmac1_rmii_refin";
 		#clock-cells = <0>;
 	};
@@ -321,6 +328,7 @@
 
 	osc: oscillator {
 		compatible = "fixed-clock";
+		bootph-pre-ram;
 		clock-output-names = "osc";
 		#clock-cells = <0>;
 	};
@@ -354,6 +362,7 @@
 		clint: timer@2000000 {
 			compatible = "starfive,jh7110-clint", "sifive,clint0";
 			reg = <0x0 0x2000000 0x0 0x10000>;
+			bootph-pre-ram;
 			interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>,
 					      <&cpu1_intc 3>, <&cpu1_intc 7>,
 					      <&cpu2_intc 3>, <&cpu2_intc 7>,
@@ -880,6 +889,7 @@
 		syscrg: clock-controller@13020000 {
 			compatible = "starfive,jh7110-syscrg";
 			reg = <0x0 0x13020000 0x0 0x10000>;
+			bootph-pre-ram;
 			clocks = <&osc>, <&gmac1_rmii_refin>,
 				 <&gmac1_rgmii_rxin>,
 				 <&i2stx_bclk_ext>, <&i2stx_lrck_ext>,
@@ -904,6 +914,7 @@
 
 			pllclk: clock-controller {
 				compatible = "starfive,jh7110-pll";
+				bootph-pre-ram;
 				clocks = <&osc>;
 				#clock-cells = <1>;
 			};
@@ -931,6 +942,19 @@
 				 <&syscrg JH7110_SYSRST_WDT_CORE>;
 		};
 
+		memory-controller@15700000 {
+			compatible = "starfive,jh7110-dmc";
+			reg = <0x0 0x15700000 0x0 0x10000>,
+			      <0x0 0x13000000 0x0 0x10000>;
+			bootph-pre-ram;
+			clocks = <&syscrg JH7110_PLLCLK_PLL1_OUT>;
+			clock-names = "pll";
+			resets = <&syscrg JH7110_SYSRST_DDR_AXI>,
+				 <&syscrg JH7110_SYSRST_DDR_OSC>,
+				 <&syscrg JH7110_SYSRST_DDR_APB>;
+			reset-names = "axi", "osc", "apb";
+		};
+
 		crypto: crypto@16000000 {
 			compatible = "starfive,jh7110-crypto";
 			reg = <0x0 0x16000000 0x0 0x4000>;