Merge tag 'sunxi-dt-for-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt

Allwinner Device Tree changes for 6.18

This tag contains two DT binding header changes that are shared with
the clk tree.

In this cycle we gained support for the MCU PRCM clock and reset
controller on the A523/A527/T527 family of SoCs, the NPU which is a
Vivante GC9000 IP block, and the NPU clock that was missing. The other
PRCM clock controller gained default bus clock rate settings. These
were not configured in the upstream U-boot bootloader, leading to them
running at slower rates. The assigned rates are from the user manual.

There is also a new board, the NetCube Systems Nagami SoM and two of
its carrier boards.

The A523 family development boards now have their internal RTC clocks
configured correctly, so that the RTC does not drift wildly. The missing
functions for the AXP717 on these boards are added. Missing reset GPIOs
and delays for Ethernet PHYs are added. Last, the Cubie A5E now has its
LEDs described and usable.

An overlay for the Orange Pi Zero interface (addon) board was added.
This can be used with the Orange Pi Zero and Zero Plus 2. Default audio
routing for these two boards (to be used with the addon) were added to
complement the overlay.

* tag 'sunxi-dt-for-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: dts: allwinner: sun55i: Complete AXP717A sub-functions
  arm64: dts: allwinner: t527: orangepi-4a: hook up external 32k crystal
  arm64: dts: allwinner: t527: avaota-a1: hook up external 32k crystal
  arm64: dts: allwinner: a527: cubie-a5e: Drop external 32.768 KHz crystal
  arm64: dts: sun55i: a523: Assign standard clock rates to PRCM bus clocks
  ARM: dts: sunxi: add support for NetCube Systems Nagami Keypad Carrier
  ARM: dts: sunxi: add support for NetCube Systems Nagami Basic Carrier
  ARM: dts: sunxi: add support for NetCube Systems Nagami SoM
  riscv: dts: allwinner: d1s-t113: Add pinctrl's required by NetCube Systems Nagami SoM
  dt-bindings: arm: sunxi: Add NetCube Systems Nagami SoM and carrier board bindings
  ARM: dts: allwinner: Add Orange Pi Zero Interface Board overlay
  ARM: dts: allwinner: orangepi-zero-plus2: Add default audio routing
  ARM: dts: allwinner: orangepi-zero: Add default audio routing
  arm64: dts: allwinner: a523: Add NPU device node
  arm64: dts: allwinner: a523: Add MCU PRCM CCU node
  dt-bindings: clock: sun55i-a523-ccu: Add A523 MCU CCU clock controller
  dt-bindings: clock: sun55i-a523-ccu: Add missing NPU module clock
  arm64: dts: allwinner: t527: avaota-a1: Add ethernet PHY reset setting
  arm64: dts: allwinner: a527: cubie-a5e: Add ethernet PHY reset setting
  arm64: dts: allwinner: a527: cubie-a5e: Add LEDs

Link: https://lore.kernel.org/r/aMrtuZg8HlR--TAt@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

7 files changed, 530 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
index d799ad153b37..f71392a55df8 100644
--- a/arch/arm/boot/dts/allwinner/Makefile
+++ b/arch/arm/boot/dts/allwinner/Makefile
@@ -182,6 +182,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-wits-pro-a20-dkt.dtb
 
 # Enables support for device-tree overlays for all pis
+DTC_FLAGS_sun8i-h2-plus-orangepi-zero := -@
 DTC_FLAGS_sun8i-h3-orangepi-lite := -@
 DTC_FLAGS_sun8i-h3-bananapi-m2-plus := -@
 DTC_FLAGS_sun8i-h3-nanopi-m1-plus := -@
@@ -199,6 +200,7 @@ DTC_FLAGS_sun8i-h3-nanopi-r1 := -@
 DTC_FLAGS_sun8i-h3-orangepi-pc := -@
 DTC_FLAGS_sun8i-h3-bananapi-m2-plus-v1.2 := -@
 DTC_FLAGS_sun8i-h3-orangepi-pc-plus := -@
+DTC_FLAGS_sun8i-t113s-netcube-nagami-basic-carrier := -@
 DTC_FLAGS_sun8i-v3s-netcube-kumquat := -@
 dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a23-evb.dtb \
@@ -225,6 +227,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h2-plus-libretech-all-h3-cc.dtb \
 	sun8i-h2-plus-orangepi-r1.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
+	sun8i-h2-plus-orangepi-zero-interface-board.dtb \
 	sun8i-h3-bananapi-m2-plus.dtb \
 	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
 	sun8i-h3-beelink-x2.dtb \
@@ -244,6 +247,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h3-orangepi-plus.dtb \
 	sun8i-h3-orangepi-plus2e.dtb \
 	sun8i-h3-orangepi-zero-plus2.dtb \
+	sun8i-h3-orangepi-zero-plus2-interface-board.dtb \
 	sun8i-h3-rervision-dvk.dtb \
 	sun8i-h3-zeropi.dtb \
 	sun8i-h3-emlid-neutis-n5h3-devboard.dtb \
@@ -257,6 +261,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-s3-lichee-zero-plus.dtb \
 	sun8i-s3-pinecube.dtb \
 	sun8i-t113s-mangopi-mq-r-t113.dtb \
+	sun8i-t113s-netcube-nagami-basic-carrier.dtb \
+	sun8i-t113s-netcube-nagami-keypad-carrier.dtb \
 	sun8i-t3-cqa3t-bv3.dtb \
 	sun8i-v3-sl631-imx179.dtb \
 	sun8i-v3s-anbernic-rg-nano.dtb \
@@ -264,6 +270,10 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-v3s-licheepi-zero-dock.dtb \
 	sun8i-v3s-netcube-kumquat.dtb \
 	sun8i-v40-bananapi-m2-berry.dtb
+sun8i-h2-plus-orangepi-zero-interface-board-dtbs += \
+	sun8i-h2-plus-orangepi-zero.dtb sun8i-orangepi-zero-interface-board.dtbo
+sun8i-h3-orangepi-zero-plus2-interface-board-dtbs += \
+	sun8i-h3-orangepi-zero-plus2.dtb sun8i-orangepi-zero-interface-board.dtbo
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
index 1b001f2ad0ef..b23cec5b89eb 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
@@ -112,6 +112,20 @@
 	};
 };
 
+/*
+ * Audio input/output is exposed on the 13-pin header and can't be used for
+ * anything else. However, adapter boards may use different audio routing.
+ * - https://linux-sunxi.org/Xunlong_Orange_Pi_Zero#Expansion_Port
+ * - Allwinner H3 Datasheet, section 3.1. Pin Characteristics
+ */
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "disabled";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_vdd_cpux>;
 };
diff --git a/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
index 7a6444a10e25..97a3565ac7a8 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
@@ -99,6 +99,20 @@
 	};
 };
 
+/*
+ * Audio input/output is exposed on the 13-pin header and can't be used for
+ * anything else. However, adapter boards may use different audio routing.
+ * - http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-Zero-Plus-2.html
+ * - Allwinner H3 Datasheet, section 3.1. Pin Characteristics
+ */
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "disabled";
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso b/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso
new file mode 100644
index 000000000000..e137eefee341
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
+/*
+ * Copyright (C) 2025 J. Neuschäfer <j.ne@posteo.net>
+ *
+ * Devicetree overlay for the Orange Pi Zero Interface board (OP0014).
+ *
+ *   https://orangepi.com/index.php?route=product/product&product_id=871
+ *
+ * This overlay applies to the following base files:
+ *
+ * - arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+ * - arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
+ */
+
+/dts-v1/;
+/plugin/;
+
+&codec {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_ir_rx_pin>;
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts
new file mode 100644
index 000000000000..5262102a85f6
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s-netcube-nagami.dtsi"
+
+/ {
+	model = "NetCube Systems Nagami Basic Carrier Board";
+	compatible = "netcube,nagami-basic-carrier", "netcube,nagami",
+		     "allwinner,sun8i-t113s";
+};
+
+&can0 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2s1 {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	broken-cd;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts
new file mode 100644
index 000000000000..4ffa6a0216d8
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s-netcube-nagami.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "NetCube Systems Nagami Keypad Carrier Board";
+	compatible = "netcube,nagami-keypad-carrier", "netcube,nagami",
+		     "allwinner,sun8i-t113s";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_red: led-status-red {
+			gpios = <&pio 3 16 GPIO_ACTIVE_HIGH>;  /* PD16 */
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
+		};
+
+		led_status_green: led-status-green {
+			gpios = <&pio 3 22 GPIO_ACTIVE_HIGH>;  /* PD22 */
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	tca8418: keypad@34 {
+		compatible = "ti,tca8418";
+		reg = <0x34>;
+		interrupts-extended = <&pio 5 6 IRQ_TYPE_EDGE_FALLING>;  /* PF6 */
+		linux,keymap = <MATRIX_KEY(0x03, 0x00, KEY_NUMERIC_A)
+				MATRIX_KEY(0x03, 0x01, KEY_NUMERIC_1)
+				MATRIX_KEY(0x03, 0x02, KEY_NUMERIC_2)
+				MATRIX_KEY(0x03, 0x03, KEY_NUMERIC_3)
+				MATRIX_KEY(0x02, 0x00, KEY_NUMERIC_B)
+				MATRIX_KEY(0x02, 0x01, KEY_NUMERIC_4)
+				MATRIX_KEY(0x02, 0x02, KEY_NUMERIC_5)
+				MATRIX_KEY(0x02, 0x03, KEY_NUMERIC_6)
+				MATRIX_KEY(0x01, 0x00, KEY_NUMERIC_C)
+				MATRIX_KEY(0x01, 0x01, KEY_NUMERIC_7)
+				MATRIX_KEY(0x01, 0x02, KEY_NUMERIC_8)
+				MATRIX_KEY(0x01, 0x03, KEY_NUMERIC_9)
+				MATRIX_KEY(0x00, 0x00, KEY_NUMERIC_D)
+				MATRIX_KEY(0x00, 0x01, KEY_CLEAR)
+				MATRIX_KEY(0x00, 0x02, KEY_NUMERIC_0)
+				MATRIX_KEY(0x00, 0x03, KEY_OK)
+		>;
+		keypad,num-rows = <4>;
+		keypad,num-columns = <4>;
+	};
+};
+
+&pio {
+	gpio-line-names = "", "", "", "", // PA
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PB
+			  "", "", "UART3_TX", "UART3_RX",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "eMMC_CLK", "eMMC_CMD", // PC
+			  "eMMC_D2", "eMMC_D1", "eMMC_D0", "eMMC_D3",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PD
+			  "", "", "", "",
+			  "", "USB_SEC_EN", "", "",
+			  "", "", "", "",
+			  "LED_STATUS_RED", "", "", "",
+			  "I2C2_SCL", "I2C2_SDA", "LED_STATUS_GREEN", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ETH_CRSDV", "ETH_RXD0", "ETH_RXD1", "ETH_TXCK", // PE
+			  "ETH_TXD0", "ETH_TXD1", "ETH_TXEN", "",
+			  "ETH_MDC", "ETH_MDIO", "QWIIC_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PF
+			  "", "", "KEY_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG
+			  "ESP_D2", "ESP_D3", "UART1_TXD", "UART1_RXD",
+			  "ESP_nBOOT", "ESP_nRST", "I2C3_SCL", "I2C3_SDA",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi
new file mode 100644
index 000000000000..544d60cfc32e
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi
@@ -0,0 +1,250 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "NetCube Systems Nagami SoM";
+	compatible = "netcube,nagami", "allwinner,sun8i-t113s";
+
+	aliases {
+		serial1 = &uart1; // ESP32 Bootloader UART
+		serial3 = &uart3; // Console UART on Card Edge
+		ethernet0 = &emac;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	/* module wide 3.3V supply directly from the card edge */
+	reg_vcc3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	/* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
+	reg_vcc_core: regulator-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-core";
+		regulator-min-microvolt = <880000>;
+		regulator-max-microvolt = <880000>;
+		vin-supply = <&reg_vcc3v3>;
+	};
+
+	/* USB0 MUX to switch connect to Card-Edge only after BootROM */
+	usb0_sec_mux: mux-controller{
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&pio 3 9 GPIO_ACTIVE_HIGH>; /* PD9 */
+		idle-state = <1>; /* USB connected to Card-Edge by default */
+	};
+
+	/* Reset of ESP32 */
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
+		post-power-on-delay-ms = <1500>;
+		power-off-delay-us = <200>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&emac {
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
+	phy-handle = <&lan8720a>;
+	phy-mode = "rmii";
+	pinctrl-0 = <&rmii_pe_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Default I2C Interface on Card-Edge */
+&i2c2 {
+	pinctrl-0 = <&i2c2_pd_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Exposed as the QWIIC connector and used by the internal EEPROM */
+&i2c3 {
+	pinctrl-0 = <&i2c3_pg_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	eeprom0: eeprom@50 {
+		compatible = "atmel,24c02";		/* actually it's a 24AA02E48 */
+		reg = <0x50>;
+		pagesize = <16>;
+		read-only;
+		vcc-supply = <&reg_vcc3v3>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		eth0_macaddress: macaddress@fa {
+			reg = <0xfa 0x06>;
+		};
+	};
+};
+
+/* Default I2S Interface on Card-Edge */
+&i2s1 {
+	pinctrl-0 = <&i2s1_pins>, <&i2s1_din0_pin>, <&i2s1_dout0_pin>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Phy is on SoM. MDI signals pre-magnetics are on the card edge */
+&mdio {
+	lan8720a: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+/* Default SD Interface on Card-Edge */
+&mmc0 {
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Connected to the on-board ESP32 */
+&mmc1 {
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+};
+
+/* Connected to the on-board eMMC */
+&mmc2 {
+	pinctrl-0 = <&mmc2_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pd-supply = <&reg_vcc3v3>;
+	vcc-pe-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
+
+	gpio-line-names = "", "", "", "", // PA
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "CAN0_TX", "CAN0_RX", // PB
+			  "CAN1_TX", "CAN1_RX", "UART3_TX", "UART3_RX",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "eMMC_CLK", "eMMC_CMD", // PC
+			  "eMMC_D2", "eMMC_D1", "eMMC_D0", "eMMC_D3",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PD
+			  "", "", "", "",
+			  "", "USB_SEC_EN", "SPI1_CS", "SPI1_CLK",
+			  "SPI1_MOSI", "SPI1_MISO", "SPI1_HOLD", "SPI1_WP",
+			  "PD16", "", "", "",
+			  "I2C2_SCL", "I2C2_SDA", "PD22", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ETH_CRSDV", "ETH_RXD0", "ETH_RXD1", "ETH_TXCK", // PE
+			  "ETH_TXD0", "ETH_TXD1", "ETH_TXEN", "",
+			  "ETH_MDC", "ETH_MDIO", "QWIIC_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "SD_D1", "SD_D0", "SD_CLK", "SD_CLK", // PF
+			  "SD_D3", "SD_D2", "PF6", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG
+			  "ESP_D2", "ESP_D3", "UART1_TXD", "UART1_RXD",
+			  "ESP_nBOOT", "ESP_nRST", "I2C3_SCL", "I2C3_SDA",
+			  "I2S1_WS", "I2S1_CLK", "I2S1_DIN0", "I2S1_DOUT0",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+/* Remove the unused CK pin from the pinctl as it is unconnected */
+&rmii_pe_pins {
+	pins = "PE0", "PE1", "PE2", "PE3", "PE4",
+	       "PE5", "PE6", "PE8", "PE9";
+};
+
+/* Default SPI Interface on Card-Edge */
+&spi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&spi1_pins>, <&spi1_hold_pin>, <&spi1_wp_pin>;
+	pinctrl-names = "default";
+	cs-gpios = <0>;
+	status = "disabled";
+};
+
+/* Connected to the Bootloader/Console of the ESP32 */
+&uart1 {
+	pinctrl-0 = <&uart1_pg6_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Console/Debug UART on Card-Edge */
+&uart3 {
+	pinctrl-0 = <&uart3_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};