Merge branch 'riscv-jh7110_initial_dts' into riscv-dt-for-next

Merge Hal's series adding support for the new StarFive JH7110 SoC.
There's a few bindings here for core components that were not picked up
by the various maintainers for the subsystems (previously Palmer would
pick these up via the RISC-V tree) & the first two commits in the branch
are shared with the clk tree, since the dts depends on defines in the
dt-binding headers.

This is based on -rc2, as the board does not actually boot on -rc1
due to the bug Linus introduced.

Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

32 files changed, 1154 insertions, 35 deletions

diff --git a/arch/alpha/lib/fpreg.c b/arch/alpha/lib/fpreg.c
index 612c5eca71bc..7c08b225261c 100644
--- a/arch/alpha/lib/fpreg.c
+++ b/arch/alpha/lib/fpreg.c
@@ -23,7 +23,7 @@ alpha_read_fp_reg (unsigned long reg)
 
 	if (unlikely(reg >= 32))
 		return 0;
-	preempt_enable();
+	preempt_disable();
 	if (current_thread_info()->status & TS_SAVED_FP)
 		val = current_thread_info()->fp[reg];
 	else switch (reg) {
@@ -133,7 +133,7 @@ alpha_read_fp_reg_s (unsigned long reg)
 	if (unlikely(reg >= 32))
 		return 0;
 
-	preempt_enable();
+	preempt_disable();
 	if (current_thread_info()->status & TS_SAVED_FP) {
 		LDT(0, current_thread_info()->fp[reg]);
 		STS(0, val);
diff --git a/arch/m68k/kernel/setup_mm.c b/arch/m68k/kernel/setup_mm.c
index 3a2bb2e8fdad..fbff1cea62ca 100644
--- a/arch/m68k/kernel/setup_mm.c
+++ b/arch/m68k/kernel/setup_mm.c
@@ -326,16 +326,16 @@ void __init setup_arch(char **cmdline_p)
 		panic("No configuration setup");
 	}
 
-#ifdef CONFIG_BLK_DEV_INITRD
-	if (m68k_ramdisk.size) {
+	if (IS_ENABLED(CONFIG_BLK_DEV_INITRD) && m68k_ramdisk.size)
 		memblock_reserve(m68k_ramdisk.addr, m68k_ramdisk.size);
+
+	paging_init();
+
+	if (IS_ENABLED(CONFIG_BLK_DEV_INITRD) && m68k_ramdisk.size) {
 		initrd_start = (unsigned long)phys_to_virt(m68k_ramdisk.addr);
 		initrd_end = initrd_start + m68k_ramdisk.size;
 		pr_info("initrd: %08lx - %08lx\n", initrd_start, initrd_end);
 	}
-#endif
-
-	paging_init();
 
 #ifdef CONFIG_NATFEAT
 	nf_init();
diff --git a/arch/m68k/kernel/traps.c b/arch/m68k/kernel/traps.c
index 5c8cba0efc63..a700807c9b6d 100644
--- a/arch/m68k/kernel/traps.c
+++ b/arch/m68k/kernel/traps.c
@@ -30,6 +30,7 @@
 #include <linux/init.h>
 #include <linux/ptrace.h>
 #include <linux/kallsyms.h>
+#include <linux/extable.h>
 
 #include <asm/setup.h>
 #include <asm/fpu.h>
@@ -545,7 +546,8 @@ static inline void bus_error030 (struct frame *fp)
 			errorcode |= 2;
 
 		if (mmusr & (MMU_I | MMU_WP)) {
-			if (ssw & 4) {
+			/* We might have an exception table for this PC */
+			if (ssw & 4 && !search_exception_tables(fp->ptregs.pc)) {
 				pr_err("Data %s fault at %#010lx in %s (pc=%#lx)\n",
 				       ssw & RW ? "read" : "write",
 				       fp->un.fmtb.daddr,
diff --git a/arch/m68k/mm/motorola.c b/arch/m68k/mm/motorola.c
index 2a375637e007..911301224078 100644
--- a/arch/m68k/mm/motorola.c
+++ b/arch/m68k/mm/motorola.c
@@ -437,7 +437,7 @@ void __init paging_init(void)
 	}
 
 	min_addr = m68k_memory[0].addr;
-	max_addr = min_addr + m68k_memory[0].size;
+	max_addr = min_addr + m68k_memory[0].size - 1;
 	memblock_add_node(m68k_memory[0].addr, m68k_memory[0].size, 0,
 			  MEMBLOCK_NONE);
 	for (i = 1; i < m68k_num_memory;) {
@@ -452,21 +452,21 @@ void __init paging_init(void)
 		}
 		memblock_add_node(m68k_memory[i].addr, m68k_memory[i].size, i,
 				  MEMBLOCK_NONE);
-		addr = m68k_memory[i].addr + m68k_memory[i].size;
+		addr = m68k_memory[i].addr + m68k_memory[i].size - 1;
 		if (addr > max_addr)
 			max_addr = addr;
 		i++;
 	}
 	m68k_memoffset = min_addr - PAGE_OFFSET;
-	m68k_virt_to_node_shift = fls(max_addr - min_addr - 1) - 6;
+	m68k_virt_to_node_shift = fls(max_addr - min_addr) - 6;
 
 	module_fixup(NULL, __start_fixup, __stop_fixup);
 	flush_icache();
 
-	high_memory = phys_to_virt(max_addr);
+	high_memory = phys_to_virt(max_addr) + 1;
 
 	min_low_pfn = availmem >> PAGE_SHIFT;
-	max_pfn = max_low_pfn = max_addr >> PAGE_SHIFT;
+	max_pfn = max_low_pfn = (max_addr >> PAGE_SHIFT) + 1;
 
 	/* Reserve kernel text/data/bss and the memory allocated in head.S */
 	memblock_reserve(m68k_memory[0].addr, availmem - m68k_memory[0].addr);
diff --git a/arch/mips/configs/mtx1_defconfig b/arch/mips/configs/mtx1_defconfig
index 89a1511d2ee4..edf9634aa8ee 100644
--- a/arch/mips/configs/mtx1_defconfig
+++ b/arch/mips/configs/mtx1_defconfig
@@ -284,6 +284,7 @@ CONFIG_IXGB=m
 CONFIG_SKGE=m
 CONFIG_SKY2=m
 CONFIG_MYRI10GE=m
+CONFIG_FEALNX=m
 CONFIG_NATSEMI=m
 CONFIG_NS83820=m
 CONFIG_S2IO=m
diff --git a/arch/powerpc/boot/dts/fsl/t1040rdb-rev-a.dts b/arch/powerpc/boot/dts/fsl/t1040rdb-rev-a.dts
index 73f8c998c64d..d4f5f159d6f2 100644
--- a/arch/powerpc/boot/dts/fsl/t1040rdb-rev-a.dts
+++ b/arch/powerpc/boot/dts/fsl/t1040rdb-rev-a.dts
@@ -10,7 +10,6 @@
 
 / {
 	model = "fsl,T1040RDB-REV-A";
-	compatible = "fsl,T1040RDB-REV-A";
 };
 
 &seville_port0 {
diff --git a/arch/powerpc/boot/dts/fsl/t1040rdb.dts b/arch/powerpc/boot/dts/fsl/t1040rdb.dts
index b6733e7e6580..dd3aab81e9de 100644
--- a/arch/powerpc/boot/dts/fsl/t1040rdb.dts
+++ b/arch/powerpc/boot/dts/fsl/t1040rdb.dts
@@ -180,6 +180,9 @@
 };
 
 &seville_port8 {
-	ethernet = <&enet0>;
+	status = "okay";
+};
+
+&seville_port9 {
 	status = "okay";
 };
diff --git a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
index f58eb820eb5e..ad0ab33336b8 100644
--- a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
+++ b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
@@ -686,6 +686,7 @@
 			seville_port8: port@8 {
 				reg = <8>;
 				phy-mode = "internal";
+				ethernet = <&enet0>;
 				status = "disabled";
 
 				fixed-link {
@@ -697,6 +698,7 @@
 			seville_port9: port@9 {
 				reg = <9>;
 				phy-mode = "internal";
+				ethernet = <&enet1>;
 				status = "disabled";
 
 				fixed-link {
diff --git a/arch/powerpc/configs/ppc6xx_defconfig b/arch/powerpc/configs/ppc6xx_defconfig
index 110258277959..f73c98be56c8 100644
--- a/arch/powerpc/configs/ppc6xx_defconfig
+++ b/arch/powerpc/configs/ppc6xx_defconfig
@@ -461,6 +461,7 @@ CONFIG_MV643XX_ETH=m
 CONFIG_SKGE=m
 CONFIG_SKY2=m
 CONFIG_MYRI10GE=m
+CONFIG_FEALNX=m
 CONFIG_NATSEMI=m
 CONFIG_NS83820=m
 CONFIG_PCMCIA_AXNET=m
diff --git a/arch/powerpc/xmon/xmon.c b/arch/powerpc/xmon/xmon.c
index 73c620c2a3a1..e753a6bd4888 100644
--- a/arch/powerpc/xmon/xmon.c
+++ b/arch/powerpc/xmon/xmon.c
@@ -1275,7 +1275,7 @@ static int xmon_batch_next_cpu(void)
 	while (!cpumask_empty(&xmon_batch_cpus)) {
 		cpu = cpumask_next_wrap(smp_processor_id(), &xmon_batch_cpus,
 					xmon_batch_start_cpu, true);
-		if (cpu == nr_cpumask_bits)
+		if (cpu >= nr_cpu_ids)
 			break;
 		if (xmon_batch_start_cpu == -1)
 			xmon_batch_start_cpu = cpu;
diff --git a/arch/riscv/Makefile b/arch/riscv/Makefile
index 6203c3378922..4de83b9b1772 100644
--- a/arch/riscv/Makefile
+++ b/arch/riscv/Makefile
@@ -84,6 +84,13 @@ endif
 # Avoid generating .eh_frame sections.
 KBUILD_CFLAGS += -fno-asynchronous-unwind-tables -fno-unwind-tables
 
+# The RISC-V attributes frequently cause compatibility issues and provide no
+# information, so just turn them off.
+KBUILD_CFLAGS += $(call cc-option,-mno-riscv-attribute)
+KBUILD_AFLAGS += $(call cc-option,-mno-riscv-attribute)
+KBUILD_CFLAGS += $(call as-option,-Wa$(comma)-mno-arch-attr)
+KBUILD_AFLAGS += $(call as-option,-Wa$(comma)-mno-arch-attr)
+
 KBUILD_CFLAGS_MODULE += $(call cc-option,-mno-relax)
 KBUILD_AFLAGS_MODULE += $(call as-option,-Wa$(comma)-mno-relax)
 
diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile
index 7b00a48580ca..170956846d49 100644
--- a/arch/riscv/boot/dts/starfive/Makefile
+++ b/arch/riscv/boot/dts/starfive/Makefile
@@ -1,2 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
-dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-beaglev-starlight.dtb jh7100-starfive-visionfive-v1.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-beaglev-starlight.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-starfive-visionfive-v1.dtb
+
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb
diff --git a/arch/riscv/boot/dts/starfive/jh7110-pinfunc.h b/arch/riscv/boot/dts/starfive/jh7110-pinfunc.h
new file mode 100644
index 000000000000..fb0139b56723
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7110-pinfunc.h
@@ -0,0 +1,308 @@
+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/*
+ * Copyright (C) 2022 Emil Renner Berthing <kernel@esmil.dk>
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
+ */
+
+#ifndef __JH7110_PINFUNC_H__
+#define __JH7110_PINFUNC_H__
+
+/*
+ * mux bits:
+ *  | 31 - 24 | 23 - 16 | 15 - 10 |  9 - 8   |  7 - 0  |
+ *  |  din    |  dout   |  doen   | function | gpio nr |
+ *
+ * dout:     output signal
+ * doen:     output enable signal
+ * din:      optional input signal, 0xff = none
+ * function: function selector
+ * gpio nr:  gpio number, 0 - 63
+ */
+#define GPIOMUX(n, dout, doen, din) ( \
+		(((din)  & 0xff) << 24) | \
+		(((dout) & 0xff) << 16) | \
+		(((doen) & 0x3f) << 10) | \
+		((n) & 0x3f))
+
+#define PINMUX(n, func) ((1 << 10) | (((func) & 0x3) << 8) | ((n) & 0xff))
+
+/* sys_iomux dout */
+#define GPOUT_LOW				0
+#define GPOUT_HIGH				1
+#define GPOUT_SYS_WAVE511_UART_TX		2
+#define GPOUT_SYS_CAN0_STBY			3
+#define GPOUT_SYS_CAN0_TST_NEXT_BIT		4
+#define GPOUT_SYS_CAN0_TST_SAMPLE_POINT		5
+#define GPOUT_SYS_CAN0_TXD			6
+#define GPOUT_SYS_USB_DRIVE_VBUS		7
+#define GPOUT_SYS_QSPI_CS1			8
+#define GPOUT_SYS_SPDIF				9
+#define GPOUT_SYS_HDMI_CEC_SDA			10
+#define GPOUT_SYS_HDMI_DDC_SCL			11
+#define GPOUT_SYS_HDMI_DDC_SDA			12
+#define GPOUT_SYS_WATCHDOG			13
+#define GPOUT_SYS_I2C0_CLK			14
+#define GPOUT_SYS_I2C0_DATA			15
+#define GPOUT_SYS_SDIO0_BACK_END_POWER		16
+#define GPOUT_SYS_SDIO0_CARD_POWER_EN		17
+#define GPOUT_SYS_SDIO0_CCMD_OD_PULLUP_EN	18
+#define GPOUT_SYS_SDIO0_RST			19
+#define GPOUT_SYS_UART0_TX			20
+#define GPOUT_SYS_HIFI4_JTAG_TDO		21
+#define GPOUT_SYS_JTAG_TDO			22
+#define GPOUT_SYS_PDM_MCLK			23
+#define GPOUT_SYS_PWM_CHANNEL0			24
+#define GPOUT_SYS_PWM_CHANNEL1			25
+#define GPOUT_SYS_PWM_CHANNEL2			26
+#define GPOUT_SYS_PWM_CHANNEL3			27
+#define GPOUT_SYS_PWMDAC_LEFT			28
+#define GPOUT_SYS_PWMDAC_RIGHT			29
+#define GPOUT_SYS_SPI0_CLK			30
+#define GPOUT_SYS_SPI0_FSS			31
+#define GPOUT_SYS_SPI0_TXD			32
+#define GPOUT_SYS_GMAC_PHYCLK			33
+#define GPOUT_SYS_I2SRX_BCLK			34
+#define GPOUT_SYS_I2SRX_LRCK			35
+#define GPOUT_SYS_I2STX0_BCLK			36
+#define GPOUT_SYS_I2STX0_LRCK			37
+#define GPOUT_SYS_MCLK				38
+#define GPOUT_SYS_TDM_CLK			39
+#define GPOUT_SYS_TDM_SYNC			40
+#define GPOUT_SYS_TDM_TXD			41
+#define GPOUT_SYS_TRACE_DATA0			42
+#define GPOUT_SYS_TRACE_DATA1			43
+#define GPOUT_SYS_TRACE_DATA2			44
+#define GPOUT_SYS_TRACE_DATA3			45
+#define GPOUT_SYS_TRACE_REF			46
+#define GPOUT_SYS_CAN1_STBY			47
+#define GPOUT_SYS_CAN1_TST_NEXT_BIT		48
+#define GPOUT_SYS_CAN1_TST_SAMPLE_POINT		49
+#define GPOUT_SYS_CAN1_TXD			50
+#define GPOUT_SYS_I2C1_CLK			51
+#define GPOUT_SYS_I2C1_DATA			52
+#define GPOUT_SYS_SDIO1_BACK_END_POWER		53
+#define GPOUT_SYS_SDIO1_CARD_POWER_EN		54
+#define GPOUT_SYS_SDIO1_CLK			55
+#define GPOUT_SYS_SDIO1_CMD_OD_PULLUP_EN	56
+#define GPOUT_SYS_SDIO1_CMD			57
+#define GPOUT_SYS_SDIO1_DATA0			58
+#define GPOUT_SYS_SDIO1_DATA1			59
+#define GPOUT_SYS_SDIO1_DATA2			60
+#define GPOUT_SYS_SDIO1_DATA3			61
+#define GPOUT_SYS_SDIO1_DATA4			63
+#define GPOUT_SYS_SDIO1_DATA5			63
+#define GPOUT_SYS_SDIO1_DATA6			64
+#define GPOUT_SYS_SDIO1_DATA7			65
+#define GPOUT_SYS_SDIO1_RST			66
+#define GPOUT_SYS_UART1_RTS			67
+#define GPOUT_SYS_UART1_TX			68
+#define GPOUT_SYS_I2STX1_SDO0			69
+#define GPOUT_SYS_I2STX1_SDO1			70
+#define GPOUT_SYS_I2STX1_SDO2			71
+#define GPOUT_SYS_I2STX1_SDO3			72
+#define GPOUT_SYS_SPI1_CLK			73
+#define GPOUT_SYS_SPI1_FSS			74
+#define GPOUT_SYS_SPI1_TXD			75
+#define GPOUT_SYS_I2C2_CLK			76
+#define GPOUT_SYS_I2C2_DATA			77
+#define GPOUT_SYS_UART2_RTS			78
+#define GPOUT_SYS_UART2_TX			79
+#define GPOUT_SYS_SPI2_CLK			80
+#define GPOUT_SYS_SPI2_FSS			81
+#define GPOUT_SYS_SPI2_TXD			82
+#define GPOUT_SYS_I2C3_CLK			83
+#define GPOUT_SYS_I2C3_DATA			84
+#define GPOUT_SYS_UART3_TX			85
+#define GPOUT_SYS_SPI3_CLK			86
+#define GPOUT_SYS_SPI3_FSS			87
+#define GPOUT_SYS_SPI3_TXD			88
+#define GPOUT_SYS_I2C4_CLK			89
+#define GPOUT_SYS_I2C4_DATA			90
+#define GPOUT_SYS_UART4_RTS			91
+#define GPOUT_SYS_UART4_TX			92
+#define GPOUT_SYS_SPI4_CLK			93
+#define GPOUT_SYS_SPI4_FSS			94
+#define GPOUT_SYS_SPI4_TXD			95
+#define GPOUT_SYS_I2C5_CLK			96
+#define GPOUT_SYS_I2C5_DATA			97
+#define GPOUT_SYS_UART5_RTS			98
+#define GPOUT_SYS_UART5_TX			99
+#define GPOUT_SYS_SPI5_CLK			100
+#define GPOUT_SYS_SPI5_FSS			101
+#define GPOUT_SYS_SPI5_TXD			102
+#define GPOUT_SYS_I2C6_CLK			103
+#define GPOUT_SYS_I2C6_DATA			104
+#define GPOUT_SYS_SPI6_CLK			105
+#define GPOUT_SYS_SPI6_FSS			106
+#define GPOUT_SYS_SPI6_TXD			107
+
+/* aon_iomux dout */
+#define GPOUT_AON_CLK_32K_OUT			2
+#define GPOUT_AON_PTC0_PWM4			3
+#define GPOUT_AON_PTC0_PWM5			4
+#define GPOUT_AON_PTC0_PWM6			5
+#define GPOUT_AON_PTC0_PWM7			6
+#define GPOUT_AON_CLK_GCLK0			7
+#define GPOUT_AON_CLK_GCLK1			8
+#define GPOUT_AON_CLK_GCLK2			9
+
+/* sys_iomux doen */
+#define GPOEN_ENABLE				0
+#define GPOEN_DISABLE				1
+#define GPOEN_SYS_HDMI_CEC_SDA			2
+#define GPOEN_SYS_HDMI_DDC_SCL			3
+#define GPOEN_SYS_HDMI_DDC_SDA			4
+#define GPOEN_SYS_I2C0_CLK			5
+#define GPOEN_SYS_I2C0_DATA			6
+#define GPOEN_SYS_HIFI4_JTAG_TDO		7
+#define GPOEN_SYS_JTAG_TDO			8
+#define GPOEN_SYS_PWM0_CHANNEL0			9
+#define GPOEN_SYS_PWM0_CHANNEL1			10
+#define GPOEN_SYS_PWM0_CHANNEL2			11
+#define GPOEN_SYS_PWM0_CHANNEL3			12
+#define GPOEN_SYS_SPI0_NSSPCTL			13
+#define GPOEN_SYS_SPI0_NSSP			14
+#define GPOEN_SYS_TDM_SYNC			15
+#define GPOEN_SYS_TDM_TXD			16
+#define GPOEN_SYS_I2C1_CLK			17
+#define GPOEN_SYS_I2C1_DATA			18
+#define GPOEN_SYS_SDIO1_CMD			19
+#define GPOEN_SYS_SDIO1_DATA0			20
+#define GPOEN_SYS_SDIO1_DATA1			21
+#define GPOEN_SYS_SDIO1_DATA2			22
+#define GPOEN_SYS_SDIO1_DATA3			23
+#define GPOEN_SYS_SDIO1_DATA4			24
+#define GPOEN_SYS_SDIO1_DATA5			25
+#define GPOEN_SYS_SDIO1_DATA6			26
+#define GPOEN_SYS_SDIO1_DATA7			27
+#define GPOEN_SYS_SPI1_NSSPCTL			28
+#define GPOEN_SYS_SPI1_NSSP			29
+#define GPOEN_SYS_I2C2_CLK			30
+#define GPOEN_SYS_I2C2_DATA			31
+#define GPOEN_SYS_SPI2_NSSPCTL			32
+#define GPOEN_SYS_SPI2_NSSP			33
+#define GPOEN_SYS_I2C3_CLK			34
+#define GPOEN_SYS_I2C3_DATA			35
+#define GPOEN_SYS_SPI3_NSSPCTL			36
+#define GPOEN_SYS_SPI3_NSSP			37
+#define GPOEN_SYS_I2C4_CLK			38
+#define GPOEN_SYS_I2C4_DATA			39
+#define GPOEN_SYS_SPI4_NSSPCTL			40
+#define GPOEN_SYS_SPI4_NSSP			41
+#define GPOEN_SYS_I2C5_CLK			42
+#define GPOEN_SYS_I2C5_DATA			43
+#define GPOEN_SYS_SPI5_NSSPCTL			44
+#define GPOEN_SYS_SPI5_NSSP			45
+#define GPOEN_SYS_I2C6_CLK			46
+#define GPOEN_SYS_I2C6_DATA			47
+#define GPOEN_SYS_SPI6_NSSPCTL			48
+#define GPOEN_SYS_SPI6_NSSP			49
+
+/* aon_iomux doen */
+#define GPOEN_AON_PTC0_OE_N_4			2
+#define GPOEN_AON_PTC0_OE_N_5			3
+#define GPOEN_AON_PTC0_OE_N_6			4
+#define GPOEN_AON_PTC0_OE_N_7			5
+
+/* sys_iomux gin */
+#define GPI_NONE				255
+
+#define GPI_SYS_WAVE511_UART_RX			0
+#define GPI_SYS_CAN0_RXD			1
+#define GPI_SYS_USB_OVERCURRENT			2
+#define GPI_SYS_SPDIF				3
+#define GPI_SYS_JTAG_RST			4
+#define GPI_SYS_HDMI_CEC_SDA			5
+#define GPI_SYS_HDMI_DDC_SCL			6
+#define GPI_SYS_HDMI_DDC_SDA			7
+#define GPI_SYS_HDMI_HPD			8
+#define GPI_SYS_I2C0_CLK			9
+#define GPI_SYS_I2C0_DATA			10
+#define GPI_SYS_SDIO0_CD			11
+#define GPI_SYS_SDIO0_INT			12
+#define GPI_SYS_SDIO0_WP			13
+#define GPI_SYS_UART0_RX			14
+#define GPI_SYS_HIFI4_JTAG_TCK			15
+#define GPI_SYS_HIFI4_JTAG_TDI			16
+#define GPI_SYS_HIFI4_JTAG_TMS			17
+#define GPI_SYS_HIFI4_JTAG_RST			18
+#define GPI_SYS_JTAG_TDI			19
+#define GPI_SYS_JTAG_TMS			20
+#define GPI_SYS_PDM_DMIC0			21
+#define GPI_SYS_PDM_DMIC1			22
+#define GPI_SYS_I2SRX_SDIN0			23
+#define GPI_SYS_I2SRX_SDIN1			24
+#define GPI_SYS_I2SRX_SDIN2			25
+#define GPI_SYS_SPI0_CLK			26
+#define GPI_SYS_SPI0_FSS			27
+#define GPI_SYS_SPI0_RXD			28
+#define GPI_SYS_JTAG_TCK			29
+#define GPI_SYS_MCLK_EXT			30
+#define GPI_SYS_I2SRX_BCLK			31
+#define GPI_SYS_I2SRX_LRCK			32
+#define GPI_SYS_I2STX0_BCLK			33
+#define GPI_SYS_I2STX0_LRCK			34
+#define GPI_SYS_TDM_CLK				35
+#define GPI_SYS_TDM_RXD				36
+#define GPI_SYS_TDM_SYNC			37
+#define GPI_SYS_CAN1_RXD			38
+#define GPI_SYS_I2C1_CLK			39
+#define GPI_SYS_I2C1_DATA			40
+#define GPI_SYS_SDIO1_CD			41
+#define GPI_SYS_SDIO1_INT			42
+#define GPI_SYS_SDIO1_WP			43
+#define GPI_SYS_SDIO1_CMD			44
+#define GPI_SYS_SDIO1_DATA0			45
+#define GPI_SYS_SDIO1_DATA1			46
+#define GPI_SYS_SDIO1_DATA2			47
+#define GPI_SYS_SDIO1_DATA3			48
+#define GPI_SYS_SDIO1_DATA4			49
+#define GPI_SYS_SDIO1_DATA5			50
+#define GPI_SYS_SDIO1_DATA6			51
+#define GPI_SYS_SDIO1_DATA7			52
+#define GPI_SYS_SDIO1_STRB			53
+#define GPI_SYS_UART1_CTS			54
+#define GPI_SYS_UART1_RX			55
+#define GPI_SYS_SPI1_CLK			56
+#define GPI_SYS_SPI1_FSS			57
+#define GPI_SYS_SPI1_RXD			58
+#define GPI_SYS_I2C2_CLK			59
+#define GPI_SYS_I2C2_DATA			60
+#define GPI_SYS_UART2_CTS			61
+#define GPI_SYS_UART2_RX			62
+#define GPI_SYS_SPI2_CLK			63
+#define GPI_SYS_SPI2_FSS			64
+#define GPI_SYS_SPI2_RXD			65
+#define GPI_SYS_I2C3_CLK			66
+#define GPI_SYS_I2C3_DATA			67
+#define GPI_SYS_UART3_RX			68
+#define GPI_SYS_SPI3_CLK			69
+#define GPI_SYS_SPI3_FSS			70
+#define GPI_SYS_SPI3_RXD			71
+#define GPI_SYS_I2C4_CLK			72
+#define GPI_SYS_I2C4_DATA			73
+#define GPI_SYS_UART4_CTS			74
+#define GPI_SYS_UART4_RX			75
+#define GPI_SYS_SPI4_CLK			76
+#define GPI_SYS_SPI4_FSS			77
+#define GPI_SYS_SPI4_RXD			78
+#define GPI_SYS_I2C5_CLK			79
+#define GPI_SYS_I2C5_DATA			80
+#define GPI_SYS_UART5_CTS			81
+#define GPI_SYS_UART5_RX			82
+#define GPI_SYS_SPI5_CLK			83
+#define GPI_SYS_SPI5_FSS			84
+#define GPI_SYS_SPI5_RXD			85
+#define GPI_SYS_I2C6_CLK			86
+#define GPI_SYS_I2C6_DATA			87
+#define GPI_SYS_SPI6_CLK			88
+#define GPI_SYS_SPI6_FSS			89
+#define GPI_SYS_SPI6_RXD			90
+
+/* aon_iomux gin */
+#define GPI_AON_PMU_GPIO_WAKEUP_0		0
+#define GPI_AON_PMU_GPIO_WAKEUP_1		1
+#define GPI_AON_PMU_GPIO_WAKEUP_2		2
+#define GPI_AON_PMU_GPIO_WAKEUP_3		3
+
+#endif
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts
new file mode 100644
index 000000000000..4af3300f3cf3
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
+ * Copyright (C) 2022 Emil Renner Berthing <kernel@esmil.dk>
+ */
+
+/dts-v1/;
+#include "jh7110-starfive-visionfive-2.dtsi"
+
+/ {
+	model = "StarFive VisionFive 2 v1.2A";
+	compatible = "starfive,visionfive-2-v1.2a", "starfive,jh7110";
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts
new file mode 100644
index 000000000000..9230cc3d8946
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
+ * Copyright (C) 2022 Emil Renner Berthing <kernel@esmil.dk>
+ */
+
+/dts-v1/;
+#include "jh7110-starfive-visionfive-2.dtsi"
+
+/ {
+	model = "StarFive VisionFive 2 v1.3B";
+	compatible = "starfive,visionfive-2-v1.3b", "starfive,jh7110";
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
new file mode 100644
index 000000000000..2a6d81609284
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
+ * Copyright (C) 2022 Emil Renner Berthing <kernel@esmil.dk>
+ */
+
+/dts-v1/;
+#include "jh7110.dtsi"
+#include "jh7110-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		i2c0 = &i2c0;
+		i2c2 = &i2c2;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cpus {
+		timebase-frequency = <4000000>;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0x1 0x0>;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&sysgpio 35 GPIO_ACTIVE_HIGH>;
+		priority = <224>;
+	};
+};
+
+&gmac0_rgmii_rxin {
+	clock-frequency = <125000000>;
+};
+
+&gmac0_rmii_refin {
+	clock-frequency = <50000000>;
+};
+
+&gmac1_rgmii_rxin {
+	clock-frequency = <125000000>;
+};
+
+&gmac1_rmii_refin {
+	clock-frequency = <50000000>;
+};
+
+&i2srx_bclk_ext {
+	clock-frequency = <12288000>;
+};
+
+&i2srx_lrck_ext {
+	clock-frequency = <192000>;
+};
+
+&i2stx_bclk_ext {
+	clock-frequency = <12288000>;
+};
+
+&i2stx_lrck_ext {
+	clock-frequency = <192000>;
+};
+
+&mclk_ext {
+	clock-frequency = <12288000>;
+};
+
+&osc {
+	clock-frequency = <24000000>;
+};
+
+&rtc_osc {
+	clock-frequency = <32768>;
+};
+
+&tdm_ext {
+	clock-frequency = <49152000>;
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	status = "okay";
+};
+
+&i2c5 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins>;
+	status = "okay";
+};
+
+&i2c6 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c6_pins>;
+	status = "okay";
+};
+
+&sysgpio {
+	i2c0_pins: i2c0-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(57, GPOUT_LOW,
+					      GPOEN_SYS_I2C0_CLK,
+					      GPI_SYS_I2C0_CLK)>,
+				 <GPIOMUX(58, GPOUT_LOW,
+					      GPOEN_SYS_I2C0_DATA,
+					      GPI_SYS_I2C0_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c2_pins: i2c2-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(3, GPOUT_LOW,
+					     GPOEN_SYS_I2C2_CLK,
+					     GPI_SYS_I2C2_CLK)>,
+				 <GPIOMUX(2, GPOUT_LOW,
+					     GPOEN_SYS_I2C2_DATA,
+					     GPI_SYS_I2C2_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c5_pins: i2c5-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(19, GPOUT_LOW,
+					      GPOEN_SYS_I2C5_CLK,
+					      GPI_SYS_I2C5_CLK)>,
+				 <GPIOMUX(20, GPOUT_LOW,
+					      GPOEN_SYS_I2C5_DATA,
+					      GPI_SYS_I2C5_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c6_pins: i2c6-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(16, GPOUT_LOW,
+					      GPOEN_SYS_I2C6_CLK,
+					      GPI_SYS_I2C6_CLK)>,
+				 <GPIOMUX(17, GPOUT_LOW,
+					      GPOEN_SYS_I2C6_DATA,
+					      GPI_SYS_I2C6_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	uart0_pins: uart0-0 {
+		tx-pins {
+			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
+					     GPOEN_ENABLE,
+					     GPI_NONE)>;
+			bias-disable;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		rx-pins {
+			pinmux = <GPIOMUX(6, GPOUT_LOW,
+					     GPOEN_DISABLE,
+					     GPI_SYS_UART0_RX)>;
+			bias-disable; /* external pull-up */
+			drive-strength = <2>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
new file mode 100644
index 000000000000..4c5fdb905da8
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -0,0 +1,500 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
+ * Copyright (C) 2022 Emil Renner Berthing <kernel@esmil.dk>
+ */
+
+/dts-v1/;
+#include <dt-bindings/clock/starfive,jh7110-crg.h>
+#include <dt-bindings/reset/starfive,jh7110-crg.h>
+
+/ {
+	compatible = "starfive,jh7110";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		S7_0: cpu@0 {
+			compatible = "sifive,s7", "riscv";
+			reg = <0>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <16384>;
+			next-level-cache = <&ccache>;
+			riscv,isa = "rv64imac_zba_zbb";
+			status = "disabled";
+
+			cpu0_intc: interrupt-controller {
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+		};
+
+		U74_1: cpu@1 {
+			compatible = "sifive,u74-mc", "riscv";
+			reg = <1>;
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <40>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <40>;
+			mmu-type = "riscv,sv39";
+			next-level-cache = <&ccache>;
+			riscv,isa = "rv64imafdc_zba_zbb";
+			tlb-split;
+
+			cpu1_intc: interrupt-controller {
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+		};
+
+		U74_2: cpu@2 {
+			compatible = "sifive,u74-mc", "riscv";
+			reg = <2>;
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <40>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <40>;
+			mmu-type = "riscv,sv39";
+			next-level-cache = <&ccache>;
+			riscv,isa = "rv64imafdc_zba_zbb";
+			tlb-split;
+
+			cpu2_intc: interrupt-controller {
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+		};
+
+		U74_3: cpu@3 {
+			compatible = "sifive,u74-mc", "riscv";
+			reg = <3>;
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <40>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <40>;
+			mmu-type = "riscv,sv39";
+			next-level-cache = <&ccache>;
+			riscv,isa = "rv64imafdc_zba_zbb";
+			tlb-split;
+
+			cpu3_intc: interrupt-controller {
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+		};
+
+		U74_4: cpu@4 {
+			compatible = "sifive,u74-mc", "riscv";
+			reg = <4>;
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <40>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <40>;
+			mmu-type = "riscv,sv39";
+			next-level-cache = <&ccache>;
+			riscv,isa = "rv64imafdc_zba_zbb";
+			tlb-split;
+
+			cpu4_intc: interrupt-controller {
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&S7_0>;
+				};
+
+				core1 {
+					cpu = <&U74_1>;
+				};
+
+				core2 {
+					cpu = <&U74_2>;
+				};
+
+				core3 {
+					cpu = <&U74_3>;
+				};
+
+				core4 {
+					cpu = <&U74_4>;
+				};
+			};
+		};
+	};
+
+	gmac0_rgmii_rxin: gmac0-rgmii-rxin-clock {
+		compatible = "fixed-clock";
+		clock-output-names = "gmac0_rgmii_rxin";
+		#clock-cells = <0>;
+	};
+
+	gmac0_rmii_refin: gmac0-rmii-refin-clock {
+		compatible = "fixed-clock";
+		clock-output-names = "gmac0_rmii_refin";
+		#clock-cells = <0>;
+	};
+
+	gmac1_rgmii_rxin: gmac1-rgmii-rxin-clock {
+		compatible = "fixed-clock";
+		clock-output-names = "gmac1_rgmii_rxin";
+		#clock-cells = <0>;
+	};
+
+	gmac1_rmii_refin: gmac1-rmii-refin-clock {
+		compatible = "fixed-clock";
+		clock-output-names = "gmac1_rmii_refin";
+		#clock-cells = <0>;
+	};
+
+	i2srx_bclk_ext: i2srx-bclk-ext-clock {
+		compatible = "fixed-clock";
+		clock-output-names = "i2srx_bclk_ext";
+		#clock-cells = <0>;
+	};
+
+	i2srx_lrck_ext: i2srx-lrck-ext-clock {
+		compatible = "fixed-clock";
+		clock-output-names = "i2srx_lrck_ext";
+		#clock-cells = <0>;
+	};
+
+	i2stx_bclk_ext: i2stx-bclk-ext-clock {
+		compatible = "fixed-clock";
+		clock-output-names = "i2stx_bclk_ext";
+		#clock-cells = <0>;
+	};
+
+	i2stx_lrck_ext: i2stx-lrck-ext-clock {
+		compatible = "fixed-clock";
+		clock-output-names = "i2stx_lrck_ext";
+		#clock-cells = <0>;
+	};
+
+	mclk_ext: mclk-ext-clock {
+		compatible = "fixed-clock";
+		clock-output-names = "mclk_ext";
+		#clock-cells = <0>;
+	};
+
+	osc: oscillator {
+		compatible = "fixed-clock";
+		clock-output-names = "osc";
+		#clock-cells = <0>;
+	};
+
+	rtc_osc: rtc-oscillator {
+		compatible = "fixed-clock";
+		clock-output-names = "rtc_osc";
+		#clock-cells = <0>;
+	};
+
+	tdm_ext: tdm-ext-clock {
+		compatible = "fixed-clock";
+		clock-output-names = "tdm_ext";
+		#clock-cells = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&plic>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		clint: timer@2000000 {
+			compatible = "starfive,jh7110-clint", "sifive,clint0";
+			reg = <0x0 0x2000000 0x0 0x10000>;
+			interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>,
+					      <&cpu1_intc 3>, <&cpu1_intc 7>,
+					      <&cpu2_intc 3>, <&cpu2_intc 7>,
+					      <&cpu3_intc 3>, <&cpu3_intc 7>,
+					      <&cpu4_intc 3>, <&cpu4_intc 7>;
+		};
+
+		ccache: cache-controller@2010000 {
+			compatible = "starfive,jh7110-ccache", "sifive,ccache0", "cache";
+			reg = <0x0 0x2010000 0x0 0x4000>;
+			interrupts = <1>, <3>, <4>, <2>;
+			cache-block-size = <64>;
+			cache-level = <2>;
+			cache-sets = <2048>;
+			cache-size = <2097152>;
+			cache-unified;
+		};
+
+		plic: interrupt-controller@c000000 {
+			compatible = "starfive,jh7110-plic", "sifive,plic-1.0.0";
+			reg = <0x0 0xc000000 0x0 0x4000000>;
+			interrupts-extended = <&cpu0_intc 11>,
+					      <&cpu1_intc 11>, <&cpu1_intc 9>,
+					      <&cpu2_intc 11>, <&cpu2_intc 9>,
+					      <&cpu3_intc 11>, <&cpu3_intc 9>,
+					      <&cpu4_intc 11>, <&cpu4_intc 9>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			#address-cells = <0>;
+			riscv,ndev = <136>;
+		};
+
+		uart0: serial@10000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x0 0x10000000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_UART0_CORE>,
+				 <&syscrg JH7110_SYSCLK_UART0_APB>;
+			clock-names = "baudclk", "apb_pclk";
+			resets = <&syscrg JH7110_SYSRST_UART0_APB>;
+			interrupts = <32>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			status = "disabled";
+		};
+
+		uart1: serial@10010000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x0 0x10010000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_UART1_CORE>,
+				 <&syscrg JH7110_SYSCLK_UART1_APB>;
+			clock-names = "baudclk", "apb_pclk";
+			resets = <&syscrg JH7110_SYSRST_UART1_APB>;
+			interrupts = <33>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			status = "disabled";
+		};
+
+		uart2: serial@10020000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x0 0x10020000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_UART2_CORE>,
+				 <&syscrg JH7110_SYSCLK_UART2_APB>;
+			clock-names = "baudclk", "apb_pclk";
+			resets = <&syscrg JH7110_SYSRST_UART2_APB>;
+			interrupts = <34>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@10030000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x10030000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_I2C0_APB>;
+			clock-names = "ref";
+			resets = <&syscrg JH7110_SYSRST_I2C0_APB>;
+			interrupts = <35>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@10040000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x10040000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_I2C1_APB>;
+			clock-names = "ref";
+			resets = <&syscrg JH7110_SYSRST_I2C1_APB>;
+			interrupts = <36>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@10050000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x10050000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_I2C2_APB>;
+			clock-names = "ref";
+			resets = <&syscrg JH7110_SYSRST_I2C2_APB>;
+			interrupts = <37>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		uart3: serial@12000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x0 0x12000000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_UART3_CORE>,
+				 <&syscrg JH7110_SYSCLK_UART3_APB>;
+			clock-names = "baudclk", "apb_pclk";
+			resets = <&syscrg JH7110_SYSRST_UART3_APB>;
+			interrupts = <45>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			status = "disabled";
+		};
+
+		uart4: serial@12010000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x0 0x12010000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_UART4_CORE>,
+				 <&syscrg JH7110_SYSCLK_UART4_APB>;
+			clock-names = "baudclk", "apb_pclk";
+			resets = <&syscrg JH7110_SYSRST_UART4_APB>;
+			interrupts = <46>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			status = "disabled";
+		};
+
+		uart5: serial@12020000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x0 0x12020000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_UART5_CORE>,
+				 <&syscrg JH7110_SYSCLK_UART5_APB>;
+			clock-names = "baudclk", "apb_pclk";
+			resets = <&syscrg JH7110_SYSRST_UART5_APB>;
+			interrupts = <47>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@12030000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x12030000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_I2C3_APB>;
+			clock-names = "ref";
+			resets = <&syscrg JH7110_SYSRST_I2C3_APB>;
+			interrupts = <48>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@12040000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x12040000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_I2C4_APB>;
+			clock-names = "ref";
+			resets = <&syscrg JH7110_SYSRST_I2C4_APB>;
+			interrupts = <49>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c5: i2c@12050000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x12050000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_I2C5_APB>;
+			clock-names = "ref";
+			resets = <&syscrg JH7110_SYSRST_I2C5_APB>;
+			interrupts = <50>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c6: i2c@12060000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x12060000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_I2C6_APB>;
+			clock-names = "ref";
+			resets = <&syscrg JH7110_SYSRST_I2C6_APB>;
+			interrupts = <51>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		syscrg: clock-controller@13020000 {
+			compatible = "starfive,jh7110-syscrg";
+			reg = <0x0 0x13020000 0x0 0x10000>;
+			clocks = <&osc>, <&gmac1_rmii_refin>,
+				 <&gmac1_rgmii_rxin>,
+				 <&i2stx_bclk_ext>, <&i2stx_lrck_ext>,
+				 <&i2srx_bclk_ext>, <&i2srx_lrck_ext>,
+				 <&tdm_ext>, <&mclk_ext>;
+			clock-names = "osc", "gmac1_rmii_refin",
+				      "gmac1_rgmii_rxin",
+				      "i2stx_bclk_ext", "i2stx_lrck_ext",
+				      "i2srx_bclk_ext", "i2srx_lrck_ext",
+				      "tdm_ext", "mclk_ext";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		sysgpio: pinctrl@13040000 {
+			compatible = "starfive,jh7110-sys-pinctrl";
+			reg = <0x0 0x13040000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_IOMUX_APB>;
+			resets = <&syscrg JH7110_SYSRST_IOMUX_APB>;
+			interrupts = <86>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		aoncrg: clock-controller@17000000 {
+			compatible = "starfive,jh7110-aoncrg";
+			reg = <0x0 0x17000000 0x0 0x10000>;
+			clocks = <&osc>, <&gmac0_rmii_refin>,
+				 <&gmac0_rgmii_rxin>,
+				 <&syscrg JH7110_SYSCLK_STG_AXIAHB>,
+				 <&syscrg JH7110_SYSCLK_APB_BUS>,
+				 <&syscrg JH7110_SYSCLK_GMAC0_GTXCLK>,
+				 <&rtc_osc>;
+			clock-names = "osc", "gmac0_rmii_refin",
+				      "gmac0_rgmii_rxin", "stg_axiahb",
+				      "apb_bus", "gmac0_gtxclk",
+				      "rtc_osc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		aongpio: pinctrl@17020000 {
+			compatible = "starfive,jh7110-aon-pinctrl";
+			reg = <0x0 0x17020000 0x0 0x10000>;
+			resets = <&aoncrg JH7110_AONRST_IOMUX>;
+			interrupts = <85>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+	};
+};
diff --git a/arch/riscv/errata/sifive/errata.c b/arch/riscv/errata/sifive/errata.c
index da55cb247e89..31d2ebea4286 100644
--- a/arch/riscv/errata/sifive/errata.c
+++ b/arch/riscv/errata/sifive/errata.c
@@ -111,7 +111,7 @@ void __init_or_module sifive_errata_patch_func(struct alt_entry *begin,
 			mutex_lock(&text_mutex);
 			patch_text_nosync(ALT_OLD_PTR(alt), ALT_ALT_PTR(alt),
 					  alt->alt_len);
-			mutex_lock(&text_mutex);
+			mutex_unlock(&text_mutex);
 			cpu_apply_errata |= tmp;
 		}
 	}
diff --git a/arch/riscv/include/asm/ftrace.h b/arch/riscv/include/asm/ftrace.h
index 9e73922e1e2e..d47d87c2d7e3 100644
--- a/arch/riscv/include/asm/ftrace.h
+++ b/arch/riscv/include/asm/ftrace.h
@@ -109,6 +109,6 @@ int ftrace_init_nop(struct module *mod, struct dyn_ftrace *rec);
 #define ftrace_init_nop ftrace_init_nop
 #endif
 
-#endif
+#endif /* CONFIG_DYNAMIC_FTRACE */
 
 #endif /* _ASM_RISCV_FTRACE_H */
diff --git a/arch/riscv/include/asm/patch.h b/arch/riscv/include/asm/patch.h
index f433121774c0..63c98833d510 100644
--- a/arch/riscv/include/asm/patch.h
+++ b/arch/riscv/include/asm/patch.h
@@ -9,4 +9,6 @@
 int patch_text_nosync(void *addr, const void *insns, size_t len);
 int patch_text(void *addr, u32 *insns, int ninsns);
 
+extern int riscv_patch_in_stop_machine;
+
 #endif /* _ASM_RISCV_PATCH_H */
diff --git a/arch/riscv/kernel/compat_vdso/Makefile b/arch/riscv/kernel/compat_vdso/Makefile
index 260daf3236d3..7f34f3c7c882 100644
--- a/arch/riscv/kernel/compat_vdso/Makefile
+++ b/arch/riscv/kernel/compat_vdso/Makefile
@@ -14,6 +14,10 @@ COMPAT_LD := $(LD)
 COMPAT_CC_FLAGS := -march=rv32g -mabi=ilp32
 COMPAT_LD_FLAGS := -melf32lriscv
 
+# Disable attributes, as they're useless and break the build.
+COMPAT_CC_FLAGS += $(call cc-option,-mno-riscv-attribute)
+COMPAT_CC_FLAGS += $(call as-option,-Wa$(comma)-mno-arch-attr)
+
 # Files to link into the compat_vdso
 obj-compat_vdso = $(patsubst %, %.o, $(compat_vdso-syms)) note.o
 
diff --git a/arch/riscv/kernel/ftrace.c b/arch/riscv/kernel/ftrace.c
index 5bff37af4770..03a6434a8cdd 100644
--- a/arch/riscv/kernel/ftrace.c
+++ b/arch/riscv/kernel/ftrace.c
@@ -15,10 +15,19 @@
 void ftrace_arch_code_modify_prepare(void) __acquires(&text_mutex)
 {
 	mutex_lock(&text_mutex);
+
+	/*
+	 * The code sequences we use for ftrace can't be patched while the
+	 * kernel is running, so we need to use stop_machine() to modify them
+	 * for now.  This doesn't play nice with text_mutex, we use this flag
+	 * to elide the check.
+	 */
+	riscv_patch_in_stop_machine = true;
 }
 
 void ftrace_arch_code_modify_post_process(void) __releases(&text_mutex)
 {
+	riscv_patch_in_stop_machine = false;
 	mutex_unlock(&text_mutex);
 }
 
@@ -107,9 +116,9 @@ int ftrace_init_nop(struct module *mod, struct dyn_ftrace *rec)
 {
 	int out;
 
-	ftrace_arch_code_modify_prepare();
+	mutex_lock(&text_mutex);
 	out = ftrace_make_nop(mod, rec, MCOUNT_ADDR);
-	ftrace_arch_code_modify_post_process();
+	mutex_unlock(&text_mutex);
 
 	return out;
 }
diff --git a/arch/riscv/kernel/patch.c b/arch/riscv/kernel/patch.c
index 8086d1a281cd..575e71d6c8ae 100644
--- a/arch/riscv/kernel/patch.c
+++ b/arch/riscv/kernel/patch.c
@@ -11,6 +11,7 @@
 #include <asm/kprobes.h>
 #include <asm/cacheflush.h>
 #include <asm/fixmap.h>
+#include <asm/ftrace.h>
 #include <asm/patch.h>
 
 struct patch_insn {
@@ -20,6 +21,8 @@ struct patch_insn {
 	atomic_t cpu_count;
 };
 
+int riscv_patch_in_stop_machine = false;
+
 #ifdef CONFIG_MMU
 /*
  * The fix_to_virt(, idx) needs a const value (not a dynamic variable of
@@ -60,8 +63,15 @@ static int patch_insn_write(void *addr, const void *insn, size_t len)
 	 * Before reaching here, it was expected to lock the text_mutex
 	 * already, so we don't need to give another lock here and could
 	 * ensure that it was safe between each cores.
+	 *
+	 * We're currently using stop_machine() for ftrace & kprobes, and while
+	 * that ensures text_mutex is held before installing the mappings it
+	 * does not ensure text_mutex is held by the calling thread.  That's
+	 * safe but triggers a lockdep failure, so just elide it for that
+	 * specific case.
 	 */
-	lockdep_assert_held(&text_mutex);
+	if (!riscv_patch_in_stop_machine)
+		lockdep_assert_held(&text_mutex);
 
 	if (across_pages)
 		patch_map(addr + len, FIX_TEXT_POKE1);
@@ -125,6 +135,7 @@ NOKPROBE_SYMBOL(patch_text_cb);
 
 int patch_text(void *addr, u32 *insns, int ninsns)
 {
+	int ret;
 	struct patch_insn patch = {
 		.addr = addr,
 		.insns = insns,
@@ -132,7 +143,18 @@ int patch_text(void *addr, u32 *insns, int ninsns)
 		.cpu_count = ATOMIC_INIT(0),
 	};
 
-	return stop_machine_cpuslocked(patch_text_cb,
-				       &patch, cpu_online_mask);
+	/*
+	 * kprobes takes text_mutex, before calling patch_text(), but as we call
+	 * calls stop_machine(), the lockdep assertion in patch_insn_write()
+	 * gets confused by the context in which the lock is taken.
+	 * Instead, ensure the lock is held before calling stop_machine(), and
+	 * set riscv_patch_in_stop_machine to skip the check in
+	 * patch_insn_write().
+	 */
+	lockdep_assert_held(&text_mutex);
+	riscv_patch_in_stop_machine = true;
+	ret = stop_machine_cpuslocked(patch_text_cb, &patch, cpu_online_mask);
+	riscv_patch_in_stop_machine = false;
+	return ret;
 }
 NOKPROBE_SYMBOL(patch_text);
diff --git a/arch/riscv/kernel/stacktrace.c b/arch/riscv/kernel/stacktrace.c
index f9a5a7c90ff0..64a9c093aef9 100644
--- a/arch/riscv/kernel/stacktrace.c
+++ b/arch/riscv/kernel/stacktrace.c
@@ -101,7 +101,7 @@ void notrace walk_stackframe(struct task_struct *task,
 	while (!kstack_end(ksp)) {
 		if (__kernel_text_address(pc) && unlikely(!fn(arg, pc)))
 			break;
-		pc = (*ksp++) - 0x4;
+		pc = READ_ONCE_NOCHECK(*ksp++) - 0x4;
 	}
 }
 
diff --git a/arch/riscv/net/bpf_jit_comp64.c b/arch/riscv/net/bpf_jit_comp64.c
index f5a668736c79..acdc3f040195 100644
--- a/arch/riscv/net/bpf_jit_comp64.c
+++ b/arch/riscv/net/bpf_jit_comp64.c
@@ -10,6 +10,7 @@
 #include <linux/filter.h>
 #include <linux/memory.h>
 #include <linux/stop_machine.h>
+#include <asm/patch.h>
 #include "bpf_jit.h"
 
 #define RV_REG_TCC RV_REG_A6
diff --git a/arch/sh/include/asm/processor_32.h b/arch/sh/include/asm/processor_32.h
index 27aebf1e75a2..3ef7adf739c8 100644
--- a/arch/sh/include/asm/processor_32.h
+++ b/arch/sh/include/asm/processor_32.h
@@ -50,6 +50,7 @@
 #define SR_FD		0x00008000
 #define SR_MD		0x40000000
 
+#define SR_USER_MASK	0x00000303	// M, Q, S, T bits
 /*
  * DSP structure and data
  */
diff --git a/arch/sh/kernel/signal_32.c b/arch/sh/kernel/signal_32.c
index 90f495d35db2..a6bfc6f37491 100644
--- a/arch/sh/kernel/signal_32.c
+++ b/arch/sh/kernel/signal_32.c
@@ -115,6 +115,7 @@ static int
 restore_sigcontext(struct pt_regs *regs, struct sigcontext __user *sc, int *r0_p)
 {
 	unsigned int err = 0;
+	unsigned int sr = regs->sr & ~SR_USER_MASK;
 
 #define COPY(x)		err |= __get_user(regs->x, &sc->sc_##x)
 			COPY(regs[1]);
@@ -130,6 +131,8 @@ restore_sigcontext(struct pt_regs *regs, struct sigcontext __user *sc, int *r0_p
 	COPY(sr);	COPY(pc);
 #undef COPY
 
+	regs->sr = (regs->sr & SR_USER_MASK) | sr;
+
 #ifdef CONFIG_SH_FPU
 	if (boot_cpu_data.flags & CPU_HAS_FPU) {
 		int owned_fp;
diff --git a/arch/x86/include/asm/resctrl.h b/arch/x86/include/asm/resctrl.h
index 52788f79786f..255a78d9d906 100644
--- a/arch/x86/include/asm/resctrl.h
+++ b/arch/x86/include/asm/resctrl.h
@@ -49,7 +49,7 @@ DECLARE_STATIC_KEY_FALSE(rdt_mon_enable_key);
  *   simple as possible.
  * Must be called with preemption disabled.
  */
-static void __resctrl_sched_in(void)
+static inline void __resctrl_sched_in(struct task_struct *tsk)
 {
 	struct resctrl_pqr_state *state = this_cpu_ptr(&pqr_state);
 	u32 closid = state->default_closid;
@@ -61,13 +61,13 @@ static void __resctrl_sched_in(void)
 	 * Else use the closid/rmid assigned to this cpu.
 	 */
 	if (static_branch_likely(&rdt_alloc_enable_key)) {
-		tmp = READ_ONCE(current->closid);
+		tmp = READ_ONCE(tsk->closid);
 		if (tmp)
 			closid = tmp;
 	}
 
 	if (static_branch_likely(&rdt_mon_enable_key)) {
-		tmp = READ_ONCE(current->rmid);
+		tmp = READ_ONCE(tsk->rmid);
 		if (tmp)
 			rmid = tmp;
 	}
@@ -88,17 +88,17 @@ static inline unsigned int resctrl_arch_round_mon_val(unsigned int val)
 	return val * scale;
 }
 
-static inline void resctrl_sched_in(void)
+static inline void resctrl_sched_in(struct task_struct *tsk)
 {
 	if (static_branch_likely(&rdt_enable_key))
-		__resctrl_sched_in();
+		__resctrl_sched_in(tsk);
 }
 
 void resctrl_cpu_detect(struct cpuinfo_x86 *c);
 
 #else
 
-static inline void resctrl_sched_in(void) {}
+static inline void resctrl_sched_in(struct task_struct *tsk) {}
 static inline void resctrl_cpu_detect(struct cpuinfo_x86 *c) {}
 
 #endif /* CONFIG_X86_CPU_RESCTRL */
diff --git a/arch/x86/kernel/cpu/amd.c b/arch/x86/kernel/cpu/amd.c
index 380753b14cab..95cdd08c4cbb 100644
--- a/arch/x86/kernel/cpu/amd.c
+++ b/arch/x86/kernel/cpu/amd.c
@@ -880,6 +880,15 @@ void init_spectral_chicken(struct cpuinfo_x86 *c)
 		}
 	}
 #endif
+	/*
+	 * Work around Erratum 1386.  The XSAVES instruction malfunctions in
+	 * certain circumstances on Zen1/2 uarch, and not all parts have had
+	 * updated microcode at the time of writing (March 2023).
+	 *
+	 * Affected parts all have no supervisor XSAVE states, meaning that
+	 * the XSAVEC instruction (which works fine) is equivalent.
+	 */
+	clear_cpu_cap(c, X86_FEATURE_XSAVES);
 }
 
 static void init_amd_zn(struct cpuinfo_x86 *c)
diff --git a/arch/x86/kernel/cpu/resctrl/rdtgroup.c b/arch/x86/kernel/cpu/resctrl/rdtgroup.c
index e2c1599d1b37..884b6e9a7e31 100644
--- a/arch/x86/kernel/cpu/resctrl/rdtgroup.c
+++ b/arch/x86/kernel/cpu/resctrl/rdtgroup.c
@@ -314,7 +314,7 @@ static void update_cpu_closid_rmid(void *info)
 	 * executing task might have its own closid selected. Just reuse
 	 * the context switch code.
 	 */
-	resctrl_sched_in();
+	resctrl_sched_in(current);
 }
 
 /*
@@ -530,7 +530,7 @@ static void _update_task_closid_rmid(void *task)
 	 * Otherwise, the MSR is updated when the task is scheduled in.
 	 */
 	if (task == current)
-		resctrl_sched_in();
+		resctrl_sched_in(task);
 }
 
 static void update_task_closid_rmid(struct task_struct *t)
diff --git a/arch/x86/kernel/process_32.c b/arch/x86/kernel/process_32.c
index 470c128759ea..708c87b88cc1 100644
--- a/arch/x86/kernel/process_32.c
+++ b/arch/x86/kernel/process_32.c
@@ -212,7 +212,7 @@ __switch_to(struct task_struct *prev_p, struct task_struct *next_p)
 	switch_fpu_finish();
 
 	/* Load the Intel cache allocation PQR MSR. */
-	resctrl_sched_in();
+	resctrl_sched_in(next_p);
 
 	return prev_p;
 }
diff --git a/arch/x86/kernel/process_64.c b/arch/x86/kernel/process_64.c
index 4e34b3b68ebd..bb65a68b4b49 100644
--- a/arch/x86/kernel/process_64.c
+++ b/arch/x86/kernel/process_64.c
@@ -656,7 +656,7 @@ __switch_to(struct task_struct *prev_p, struct task_struct *next_p)
 	}
 
 	/* Load the Intel cache allocation PQR MSR. */
-	resctrl_sched_in();
+	resctrl_sched_in(next_p);
 
 	return prev_p;
 }