Merge tag 'mfd-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull mfd updates from Lee Jones:

 - Fix race in device_node_get_regmap() using more extensive locking

 - Remove unused platform driver support for syscon

 - Allow syscon nodes to be registered without a "syscon" compatible
   string

 - Make `platform_data` pointer const in struct mfd_cell

 - Revert support for multiple AXP PMICs to avoid regressions

 - Increase SoundWire attach timeout and use gpiod_set_raw() for GPIO
   operation

 - Store the result from fault_log() for use by other sub-components

 - Fix an invalid regmap-config max_register value

 - Add another Gemini Lake ISA bridge PCI device ID

 - Use devm_register_power_off_handler() to simplify code

 - Add support for QNAP microcontroller units, including LEDs, input,
   and hwmon

 - Use MFD_CELL macros and remove unused code

 - Add support for AAEON UP board FPGA

 - Remove unused includes

 - Fix various typos and compatibility issues in multiple bindings

 - Add new bindings for rk3562 QoS, LED1202, and qcom,tcsr-ipq5424

 - Convert several bindings to YAML schema

 - Update sprd,sc2731 bindings to reference sprd,sc2731-efuse bindings
   directly

 - Fix rohm,bd71815 bindings by correcting resistor values and typos

 - Documentation improvements:
    - Add documentation for LED1202 and qnap-mcu-hwmon
    - Adjust the file entry for the qnap-mcu header in MAINTAINERS

* tag 'mfd-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (35 commits)
  MAINTAINERS: Adjust the file entry for the qnap-mcu header
  dt-bindings: mfd: syscon: Fix ti,j784s4-acspcie-proxy-ctrl compatible
  dt-bindings: mfd: syscon: Fix al,alpine-sysfabric-service compatible
  Revert "mfd: axp20x: Allow multiple regulators"
  dt-bindings: mfd: syscon: Add rk3562 QoS register compatible
  mfd: syscon: Allow syscon nodes without a "syscon" compatible
  mfd: syscon: Remove the platform driver support
  mfd: syscon: Fix race in device_node_get_regmap()
  dt-bindings: mfd: atmel: Convert to YAML schema
  dt-bindings: mfd: atmel,at91sam9260: Convert to YAML schema
  dt-bindings: mfd: sprd,sc2731: Reference sprd,sc2731-efuse bindings
  mfd: tps65219: Remove unused macros & add regmap.h
  mfd: tps65219: Use MFD_CELL macros
  leds: Add LED1202 I2C driver
  dt-bindings: leds: Add LED1202 LED Controller
  Documentation:leds: Add leds-st1202.rst
  mfd: Add support for AAEON UP board FPGA
  mfd: da9052: Store result from fault_log
  mfd: intel_soc_pmic_chtdc_ti: Fix invalid regmap-config max_register value
  mfd: cs42l43: Use devres for remove as well
  ...

3 files changed, 377 insertions, 0 deletions

diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index ea13ea482a63..ea2f095da63e 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1822,6 +1822,18 @@ config SENSORS_PWM_FAN
 	  This driver can also be built as a module. If so, the module
 	  will be called pwm-fan.
 
+config SENSORS_QNAP_MCU_HWMON
+	tristate "QNAP MCU hardware monitoring"
+	depends on MFD_QNAP_MCU
+	depends on THERMAL || THERMAL=n
+	help
+	  Say yes here to enable support for fan and temperature sensor
+	  connected to a QNAP MCU, as found in a number of QNAP network
+	  attached storage devices.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called qnap-mcu-hwmon.
+
 config SENSORS_RASPBERRYPI_HWMON
 	tristate "Raspberry Pi voltage monitor"
 	depends on RASPBERRYPI_FIRMWARE || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index b827b92f2a78..b7ef0f0562d3 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -189,6 +189,7 @@ obj-$(CONFIG_SENSORS_POWERZ)	+= powerz.o
 obj-$(CONFIG_SENSORS_POWR1220)  += powr1220.o
 obj-$(CONFIG_SENSORS_PT5161L)	+= pt5161l.o
 obj-$(CONFIG_SENSORS_PWM_FAN)	+= pwm-fan.o
+obj-$(CONFIG_SENSORS_QNAP_MCU_HWMON)	+= qnap-mcu-hwmon.o
 obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON)	+= raspberrypi-hwmon.o
 obj-$(CONFIG_SENSORS_SBTSI)	+= sbtsi_temp.o
 obj-$(CONFIG_SENSORS_SBRMI)	+= sbrmi.o
diff --git a/drivers/hwmon/qnap-mcu-hwmon.c b/drivers/hwmon/qnap-mcu-hwmon.c
new file mode 100644
index 000000000000..29057514739c
--- /dev/null
+++ b/drivers/hwmon/qnap-mcu-hwmon.c
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/*
+ * Driver for hwmon elements found on QNAP-MCU devices
+ *
+ * Copyright (C) 2024 Heiko Stuebner <heiko@sntech.de>
+ */
+
+#include <linux/fwnode.h>
+#include <linux/hwmon.h>
+#include <linux/mfd/qnap-mcu.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/thermal.h>
+
+struct qnap_mcu_hwmon {
+	struct qnap_mcu *mcu;
+	struct device *dev;
+
+	unsigned int pwm_min;
+	unsigned int pwm_max;
+
+	struct fwnode_handle *fan_node;
+	unsigned int fan_state;
+	unsigned int fan_max_state;
+	unsigned int *fan_cooling_levels;
+
+	struct thermal_cooling_device *cdev;
+	struct hwmon_chip_info info;
+};
+
+static int qnap_mcu_hwmon_get_rpm(struct qnap_mcu_hwmon *hwm)
+{
+	static const u8 cmd[] = { '@', 'F', 'A' };
+	u8 reply[6];
+	int ret;
+
+	/* poll the fan rpm */
+	ret = qnap_mcu_exec(hwm->mcu, cmd, sizeof(cmd), reply, sizeof(reply));
+	if (ret)
+		return ret;
+
+	/* First 2 bytes must mirror the sent command */
+	if (memcmp(cmd, reply, 2))
+		return -EIO;
+
+	return reply[4] * 30;
+}
+
+static int qnap_mcu_hwmon_get_pwm(struct qnap_mcu_hwmon *hwm)
+{
+	static const u8 cmd[] = { '@', 'F', 'Z', '0' }; /* 0 = fan-id? */
+	u8 reply[4];
+	int ret;
+
+	/* poll the fan pwm */
+	ret = qnap_mcu_exec(hwm->mcu, cmd, sizeof(cmd), reply, sizeof(reply));
+	if (ret)
+		return ret;
+
+	/* First 3 bytes must mirror the sent command */
+	if (memcmp(cmd, reply, 3))
+		return -EIO;
+
+	return reply[3];
+}
+
+static int qnap_mcu_hwmon_set_pwm(struct qnap_mcu_hwmon *hwm, u8 pwm)
+{
+	const u8 cmd[] = { '@', 'F', 'W', '0', pwm }; /* 0 = fan-id?, pwm 0-255 */
+
+	/* set the fan pwm */
+	return qnap_mcu_exec_with_ack(hwm->mcu, cmd, sizeof(cmd));
+}
+
+static int qnap_mcu_hwmon_get_temp(struct qnap_mcu_hwmon *hwm)
+{
+	static const u8 cmd[] = { '@', 'T', '3' };
+	u8 reply[4];
+	int ret;
+
+	/* poll the fan rpm */
+	ret = qnap_mcu_exec(hwm->mcu, cmd, sizeof(cmd), reply, sizeof(reply));
+	if (ret)
+		return ret;
+
+	/* First bytes must mirror the sent command */
+	if (memcmp(cmd, reply, sizeof(cmd)))
+		return -EIO;
+
+	/*
+	 * There is an unknown bit set in bit7.
+	 * Bits [6:0] report the actual temperature as returned by the
+	 * original qnap firmware-tools, so just drop bit7 for now.
+	 */
+	return (reply[3] & 0x7f) * 1000;
+}
+
+static int qnap_mcu_hwmon_write(struct device *dev, enum hwmon_sensor_types type,
+				u32 attr, int channel, long val)
+{
+	struct qnap_mcu_hwmon *hwm = dev_get_drvdata(dev);
+
+	switch (attr) {
+	case hwmon_pwm_input:
+		if (val < 0 || val > 255)
+			return -EINVAL;
+
+		if (val != 0)
+			val = clamp_val(val, hwm->pwm_min, hwm->pwm_max);
+
+		return qnap_mcu_hwmon_set_pwm(hwm, val);
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	return 0;
+}
+
+static int qnap_mcu_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
+			       u32 attr, int channel, long *val)
+{
+	struct qnap_mcu_hwmon *hwm = dev_get_drvdata(dev);
+	int ret;
+
+	switch (type) {
+	case hwmon_pwm:
+		switch (attr) {
+		case hwmon_pwm_input:
+			ret = qnap_mcu_hwmon_get_pwm(hwm);
+			if (ret < 0)
+				return ret;
+
+			*val = ret;
+			return 0;
+		default:
+			return -EOPNOTSUPP;
+		}
+	case hwmon_fan:
+		ret = qnap_mcu_hwmon_get_rpm(hwm);
+		if (ret < 0)
+			return ret;
+
+		*val = ret;
+		return 0;
+	case hwmon_temp:
+		ret = qnap_mcu_hwmon_get_temp(hwm);
+		if (ret < 0)
+			return ret;
+
+		*val = ret;
+		return 0;
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static umode_t qnap_mcu_hwmon_is_visible(const void *data,
+					 enum hwmon_sensor_types type,
+					 u32 attr, int channel)
+{
+	switch (type) {
+	case hwmon_temp:
+		return 0444;
+
+	case hwmon_pwm:
+		return 0644;
+
+	case hwmon_fan:
+		return 0444;
+
+	default:
+		return 0;
+	}
+}
+
+static const struct hwmon_ops qnap_mcu_hwmon_hwmon_ops = {
+	.is_visible = qnap_mcu_hwmon_is_visible,
+	.read = qnap_mcu_hwmon_read,
+	.write = qnap_mcu_hwmon_write,
+};
+
+/* thermal cooling device callbacks */
+static int qnap_mcu_hwmon_get_max_state(struct thermal_cooling_device *cdev,
+					unsigned long *state)
+{
+	struct qnap_mcu_hwmon *hwm = cdev->devdata;
+
+	if (!hwm)
+		return -EINVAL;
+
+	*state = hwm->fan_max_state;
+
+	return 0;
+}
+
+static int qnap_mcu_hwmon_get_cur_state(struct thermal_cooling_device *cdev,
+					unsigned long *state)
+{
+	struct qnap_mcu_hwmon *hwm = cdev->devdata;
+
+	if (!hwm)
+		return -EINVAL;
+
+	*state = hwm->fan_state;
+
+	return 0;
+}
+
+static int qnap_mcu_hwmon_set_cur_state(struct thermal_cooling_device *cdev,
+					unsigned long state)
+{
+	struct qnap_mcu_hwmon *hwm = cdev->devdata;
+	int ret;
+
+	if (!hwm || state > hwm->fan_max_state)
+		return -EINVAL;
+
+	if (state == hwm->fan_state)
+		return 0;
+
+	ret = qnap_mcu_hwmon_set_pwm(hwm, hwm->fan_cooling_levels[state]);
+	if (ret)
+		return ret;
+
+	hwm->fan_state = state;
+
+	return ret;
+}
+
+static const struct thermal_cooling_device_ops qnap_mcu_hwmon_cooling_ops = {
+	.get_max_state = qnap_mcu_hwmon_get_max_state,
+	.get_cur_state = qnap_mcu_hwmon_get_cur_state,
+	.set_cur_state = qnap_mcu_hwmon_set_cur_state,
+};
+
+static void devm_fan_node_release(void *data)
+{
+	struct qnap_mcu_hwmon *hwm = data;
+
+	fwnode_handle_put(hwm->fan_node);
+}
+
+static int qnap_mcu_hwmon_get_cooling_data(struct device *dev, struct qnap_mcu_hwmon *hwm)
+{
+	struct fwnode_handle *fwnode;
+	int num, i, ret;
+
+	fwnode = device_get_named_child_node(dev->parent, "fan-0");
+	if (!fwnode)
+		return 0;
+
+	/* if we found the fan-node, we're keeping it until device-unbind */
+	hwm->fan_node = fwnode;
+	ret = devm_add_action_or_reset(dev, devm_fan_node_release, hwm);
+	if (ret)
+		return ret;
+
+	num = fwnode_property_count_u32(fwnode, "cooling-levels");
+	if (num <= 0)
+		return dev_err_probe(dev, num ? : -EINVAL,
+				     "Failed to count elements in 'cooling-levels'\n");
+
+	hwm->fan_cooling_levels = devm_kcalloc(dev, num, sizeof(u32),
+					       GFP_KERNEL);
+	if (!hwm->fan_cooling_levels)
+		return -ENOMEM;
+
+	ret = fwnode_property_read_u32_array(fwnode, "cooling-levels",
+					     hwm->fan_cooling_levels, num);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to read 'cooling-levels'\n");
+
+	for (i = 0; i < num; i++) {
+		if (hwm->fan_cooling_levels[i] > hwm->pwm_max)
+			return dev_err_probe(dev, -EINVAL, "fan state[%d]:%d > %d\n", i,
+					     hwm->fan_cooling_levels[i], hwm->pwm_max);
+	}
+
+	hwm->fan_max_state = num - 1;
+
+	return 0;
+}
+
+static const struct hwmon_channel_info * const qnap_mcu_hwmon_channels[] = {
+	HWMON_CHANNEL_INFO(pwm, HWMON_PWM_INPUT),
+	HWMON_CHANNEL_INFO(fan, HWMON_F_INPUT),
+	HWMON_CHANNEL_INFO(temp, HWMON_T_INPUT),
+	NULL
+};
+
+static int qnap_mcu_hwmon_probe(struct platform_device *pdev)
+{
+	struct qnap_mcu *mcu = dev_get_drvdata(pdev->dev.parent);
+	const struct qnap_mcu_variant *variant = pdev->dev.platform_data;
+	struct qnap_mcu_hwmon *hwm;
+	struct thermal_cooling_device *cdev;
+	struct device *dev = &pdev->dev;
+	struct device *hwmon;
+	int ret;
+
+	hwm = devm_kzalloc(dev, sizeof(*hwm), GFP_KERNEL);
+	if (!hwm)
+		return -ENOMEM;
+
+	hwm->mcu = mcu;
+	hwm->dev = &pdev->dev;
+	hwm->pwm_min = variant->fan_pwm_min;
+	hwm->pwm_max = variant->fan_pwm_max;
+
+	platform_set_drvdata(pdev, hwm);
+
+	/*
+	 * Set duty cycle to maximum allowed.
+	 */
+	ret = qnap_mcu_hwmon_set_pwm(hwm, hwm->pwm_max);
+	if (ret)
+		return ret;
+
+	hwm->info.ops = &qnap_mcu_hwmon_hwmon_ops;
+	hwm->info.info = qnap_mcu_hwmon_channels;
+
+	ret = qnap_mcu_hwmon_get_cooling_data(dev, hwm);
+	if (ret)
+		return ret;
+
+	hwm->fan_state = hwm->fan_max_state;
+
+	hwmon = devm_hwmon_device_register_with_info(dev, "qnapmcu",
+						     hwm, &hwm->info, NULL);
+	if (IS_ERR(hwmon))
+		return dev_err_probe(dev, PTR_ERR(hwmon), "Failed to register hwmon device\n");
+
+	/*
+	 * Only register cooling device when we found cooling-levels.
+	 * qnap_mcu_hwmon_get_cooling_data() will fail when reading malformed
+	 * levels and only succeed with either no or correct cooling levels.
+	 */
+	if (IS_ENABLED(CONFIG_THERMAL) && hwm->fan_cooling_levels) {
+		cdev = devm_thermal_of_cooling_device_register(dev,
+					to_of_node(hwm->fan_node), "qnap-mcu-hwmon",
+					hwm, &qnap_mcu_hwmon_cooling_ops);
+		if (IS_ERR(cdev))
+			return dev_err_probe(dev, PTR_ERR(cdev),
+				"Failed to register qnap-mcu-hwmon as cooling device\n");
+		hwm->cdev = cdev;
+	}
+
+	return 0;
+}
+
+static struct platform_driver qnap_mcu_hwmon_driver = {
+	.probe = qnap_mcu_hwmon_probe,
+	.driver = {
+		.name = "qnap-mcu-hwmon",
+	},
+};
+module_platform_driver(qnap_mcu_hwmon_driver);
+
+MODULE_ALIAS("platform:qnap-mcu-hwmon");
+MODULE_AUTHOR("Heiko Stuebner <heiko@sntech.de>");
+MODULE_DESCRIPTION("QNAP MCU hwmon driver");
+MODULE_LICENSE("GPL");