Merge tag 'asoc-v4.2' into asoc-rt5645

ASoC: Updates for v4.2

The big thing this release has been Liam's addition of topology support
to the core.  We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.

 - Support for loading ASoC topology maps from firmware, intended to be
   used to allow self-describing DSP firmware images to be built which
   can map controls added by the DSP to userspace without the kernel
   needing to know about individual DSP firmwares.
 - Lots of refactoring to avoid direct access to snd_soc_codec where
   it's not needed supporting future refactoring.
 - Big refactoring and cleanup serieses for the Wolfson ADSP and TI
   TAS2552 drivers.
 - Support for TI TAS571x power amplifiers.
 - Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
 - Support for x86 systems with RT5650 and Qualcomm Storm.

1 files changed, 19 insertions, 15 deletions

diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 52cd8db2c57d..47cd578052fc 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -742,6 +742,9 @@ EXPORT_SYMBOL(phy_stop);
  */
 void phy_start(struct phy_device *phydev)
 {
+	bool do_resume = false;
+	int err = 0;
+
 	mutex_lock(&phydev->lock);
 
 	switch (phydev->state) {
@@ -752,11 +755,22 @@ void phy_start(struct phy_device *phydev)
 		phydev->state = PHY_UP;
 		break;
 	case PHY_HALTED:
+		/* make sure interrupts are re-enabled for the PHY */
+		err = phy_enable_interrupts(phydev);
+		if (err < 0)
+			break;
+
 		phydev->state = PHY_RESUMING;
+		do_resume = true;
+		break;
 	default:
 		break;
 	}
 	mutex_unlock(&phydev->lock);
+
+	/* if phy was suspended, bring the physical link up again */
+	if (do_resume)
+		phy_resume(phydev);
 }
 EXPORT_SYMBOL(phy_start);
 
@@ -769,7 +783,7 @@ void phy_state_machine(struct work_struct *work)
 	struct delayed_work *dwork = to_delayed_work(work);
 	struct phy_device *phydev =
 			container_of(dwork, struct phy_device, state_queue);
-	bool needs_aneg = false, do_suspend = false, do_resume = false;
+	bool needs_aneg = false, do_suspend = false;
 	int err = 0;
 
 	mutex_lock(&phydev->lock);
@@ -888,14 +902,6 @@ void phy_state_machine(struct work_struct *work)
 		}
 		break;
 	case PHY_RESUMING:
-		err = phy_clear_interrupt(phydev);
-		if (err)
-			break;
-
-		err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED);
-		if (err)
-			break;
-
 		if (AUTONEG_ENABLE == phydev->autoneg) {
 			err = phy_aneg_done(phydev);
 			if (err < 0)
@@ -933,7 +939,6 @@ void phy_state_machine(struct work_struct *work)
 			}
 			phydev->adjust_link(phydev->attached_dev);
 		}
-		do_resume = true;
 		break;
 	}
 
@@ -943,8 +948,6 @@ void phy_state_machine(struct work_struct *work)
 		err = phy_start_aneg(phydev);
 	else if (do_suspend)
 		phy_suspend(phydev);
-	else if (do_resume)
-		phy_resume(phydev);
 
 	if (err < 0)
 		phy_error(phydev);
@@ -1053,13 +1056,14 @@ int phy_init_eee(struct phy_device *phydev, bool clk_stop_enable)
 {
 	/* According to 802.3az,the EEE is supported only in full duplex-mode.
 	 * Also EEE feature is active when core is operating with MII, GMII
-	 * or RGMII. Internal PHYs are also allowed to proceed and should
-	 * return an error if they do not support EEE.
+	 * or RGMII (all kinds). Internal PHYs are also allowed to proceed and
+	 * should return an error if they do not support EEE.
 	 */
 	if ((phydev->duplex == DUPLEX_FULL) &&
 	    ((phydev->interface == PHY_INTERFACE_MODE_MII) ||
 	    (phydev->interface == PHY_INTERFACE_MODE_GMII) ||
-	    (phydev->interface == PHY_INTERFACE_MODE_RGMII) ||
+	    (phydev->interface >= PHY_INTERFACE_MODE_RGMII &&
+	     phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID) ||
 	     phy_is_internal(phydev))) {
 		int eee_lp, eee_cap, eee_adv;
 		u32 lp, cap, adv;