Merge tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Merge "wireless wl12xx and omap device tree changes for v4.1" from Tony
Lindgren:

Wireless and omap changes to make wl12xx driver to use device tree
data instead of platform data from Eliad Peller <eliad@wizery.com>:

- Add device-tree support to the wlcore (wl12xx/wl18xx) driver.

- Update the current users to use the bindings instead of pdata-quirks.

- Finally, remove the deprecated wl12xx_platform_data struct

Note that da850 board file code that still uses the platform data,
but we have da850.dtsi that can be used instead. So it was decided
that we should try to remove the wl12xx support from the da850
board file as suggested by Sekhar Nori <nsekhar@ti.com>. As it's
the last patch in the series, the last patch can be simply reverted
if needed.

As this series touches quite a bit of arch code, it was suggested
by Kalle Valo <kvalo@codeaurora.org> that the whole series should
be merged via the arm-soc tree.

* tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  wlcore: remove wl12xx_platform_data
  ARM: dts: add wl12xx/wl18xx bindings
  wlcore: add device-tree support
  dt: bindings: add TI's wilink wireless device
  wl12xx: use frequency instead of enumerations for pdata clocks
  wlcore: set irq_trigger in board files instead of hiding behind a quirk
  + Linux 4.0-rc4

Signed-off-by: Olof Johansson <olof@lixom.net>

9 files changed, 99 insertions, 54 deletions

diff --git a/drivers/tty/bfin_jtag_comm.c b/drivers/tty/bfin_jtag_comm.c
index d7b198c400c7..ce24182f8514 100644
--- a/drivers/tty/bfin_jtag_comm.c
+++ b/drivers/tty/bfin_jtag_comm.c
@@ -210,18 +210,6 @@ bfin_jc_chars_in_buffer(struct tty_struct *tty)
 	return circ_cnt(&bfin_jc_write_buf);
 }
 
-static void
-bfin_jc_wait_until_sent(struct tty_struct *tty, int timeout)
-{
-	unsigned long expire = jiffies + timeout;
-	while (!circ_empty(&bfin_jc_write_buf)) {
-		if (signal_pending(current))
-			break;
-		if (time_after(jiffies, expire))
-			break;
-	}
-}
-
 static const struct tty_operations bfin_jc_ops = {
 	.open            = bfin_jc_open,
 	.close           = bfin_jc_close,
@@ -230,7 +218,6 @@ static const struct tty_operations bfin_jc_ops = {
 	.flush_chars     = bfin_jc_flush_chars,
 	.write_room      = bfin_jc_write_room,
 	.chars_in_buffer = bfin_jc_chars_in_buffer,
-	.wait_until_sent = bfin_jc_wait_until_sent,
 };
 
 static int __init bfin_jc_init(void)
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index e3b9570a1eff..deae122c9c4b 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -2138,8 +2138,8 @@ int serial8250_do_startup(struct uart_port *port)
 	/*
 	 * Clear the interrupt registers.
 	 */
-	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
-		serial_port_in(port, UART_RX);
+	serial_port_in(port, UART_LSR);
+	serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
 
@@ -2300,8 +2300,8 @@ dont_test_tx_en:
 	 * saved flags to avoid getting false values from polling
 	 * routines or the previous session.
 	 */
-	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
-		serial_port_in(port, UART_RX);
+	serial_port_in(port, UART_LSR);
+	serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
 	up->lsr_saved_flags = 0;
@@ -2394,8 +2394,7 @@ void serial8250_do_shutdown(struct uart_port *port)
 	 * Read data port to reset things, and then unlink from
 	 * the IRQ chain.
 	 */
-	if (serial_port_in(port, UART_LSR) & UART_LSR_DR)
-		serial_port_in(port, UART_RX);
+	serial_port_in(port, UART_RX);
 	serial8250_rpm_put(up);
 
 	del_timer_sync(&up->timer);
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index e60116235836..2ab229ddee38 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -59,6 +59,8 @@ struct dw8250_data {
 	u8			usr_reg;
 	int			last_mcr;
 	int			line;
+	int			msr_mask_on;
+	int			msr_mask_off;
 	struct clk		*clk;
 	struct clk		*pclk;
 	struct reset_control	*rst;
@@ -81,6 +83,12 @@ static inline int dw8250_modify_msr(struct uart_port *p, int offset, int value)
 		value &= ~UART_MSR_DCTS;
 	}
 
+	/* Override any modem control signals if needed */
+	if (offset == UART_MSR) {
+		value |= d->msr_mask_on;
+		value &= ~d->msr_mask_off;
+	}
+
 	return value;
 }
 
@@ -334,6 +342,30 @@ static int dw8250_probe_of(struct uart_port *p,
 	if (id >= 0)
 		p->line = id;
 
+	if (of_property_read_bool(np, "dcd-override")) {
+		/* Always report DCD as active */
+		data->msr_mask_on |= UART_MSR_DCD;
+		data->msr_mask_off |= UART_MSR_DDCD;
+	}
+
+	if (of_property_read_bool(np, "dsr-override")) {
+		/* Always report DSR as active */
+		data->msr_mask_on |= UART_MSR_DSR;
+		data->msr_mask_off |= UART_MSR_DDSR;
+	}
+
+	if (of_property_read_bool(np, "cts-override")) {
+		/* Always report DSR as active */
+		data->msr_mask_on |= UART_MSR_DSR;
+		data->msr_mask_off |= UART_MSR_DDSR;
+	}
+
+	if (of_property_read_bool(np, "ri-override")) {
+		/* Always report Ring indicator as inactive */
+		data->msr_mask_off |= UART_MSR_RI;
+		data->msr_mask_off |= UART_MSR_TERI;
+	}
+
 	/* clock got configured through clk api, all done */
 	if (p->uartclk)
 		return 0;
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index daf2c82984e9..892eb32cdef4 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -69,7 +69,7 @@ static void moan_device(const char *str, struct pci_dev *dev)
 	       "Please send the output of lspci -vv, this\n"
 	       "message (0x%04x,0x%04x,0x%04x,0x%04x), the\n"
 	       "manufacturer and name of serial board or\n"
-	       "modem board to rmk+serial@arm.linux.org.uk.\n",
+	       "modem board to <linux-serial@vger.kernel.org>.\n",
 	       pci_name(dev), str, dev->vendor, dev->device,
 	       dev->subsystem_vendor, dev->subsystem_device);
 }
@@ -1989,13 +1989,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 	},
 	{
 		.vendor		= PCI_VENDOR_ID_INTEL,
-		.device		= PCI_DEVICE_ID_INTEL_QRK_UART,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_default_setup,
-	},
-	{
-		.vendor		= PCI_VENDOR_ID_INTEL,
 		.device		= PCI_DEVICE_ID_INTEL_BSW_UART1,
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
@@ -2201,13 +2194,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 	 */
 	{
 		.vendor		= PCI_VENDOR_ID_PLX,
-		.device		= PCI_DEVICE_ID_PLX_9030,
-		.subvendor	= PCI_SUBVENDOR_ID_PERLE,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_default_setup,
-	},
-	{
-		.vendor		= PCI_VENDOR_ID_PLX,
 		.device		= PCI_DEVICE_ID_PLX_9050,
 		.subvendor	= PCI_SUBVENDOR_ID_EXSYS,
 		.subdevice	= PCI_SUBDEVICE_ID_EXSYS_4055,
@@ -5415,10 +5401,6 @@ static struct pci_device_id serial_pci_tbl[] = {
 		PCI_ANY_ID, PCI_ANY_ID,
 		0, 0, pbn_b0_bt_2_115200 },
 
-	{	PCI_VENDOR_ID_WCH, PCI_DEVICE_ID_WCH_CH352_2S,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0, 0, pbn_b0_bt_2_115200 },
-
 	{	PCIE_VENDOR_ID_WCH, PCIE_DEVICE_ID_WCH_CH384_4S,
 		PCI_ANY_ID, PCI_ANY_ID,
 		0, 0, pbn_wch384_4 },
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 846552bff67d..4e959c43f680 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -47,6 +47,7 @@
 #include <linux/gpio/consumer.h>
 #include <linux/err.h>
 #include <linux/irq.h>
+#include <linux/suspend.h>
 
 #include <asm/io.h>
 #include <asm/ioctls.h>
@@ -173,6 +174,12 @@ struct atmel_uart_port {
 	bool			ms_irq_enabled;
 	bool			is_usart;	/* usart or uart */
 	struct timer_list	uart_timer;	/* uart timer */
+
+	bool			suspended;
+	unsigned int		pending;
+	unsigned int		pending_status;
+	spinlock_t		lock_suspended;
+
 	int (*prepare_rx)(struct uart_port *port);
 	int (*prepare_tx)(struct uart_port *port);
 	void (*schedule_rx)(struct uart_port *port);
@@ -1179,12 +1186,15 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id)
 {
 	struct uart_port *port = dev_id;
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
-	unsigned int status, pending, pass_counter = 0;
+	unsigned int status, pending, mask, pass_counter = 0;
 	bool gpio_handled = false;
 
+	spin_lock(&atmel_port->lock_suspended);
+
 	do {
 		status = atmel_get_lines_status(port);
-		pending = status & UART_GET_IMR(port);
+		mask = UART_GET_IMR(port);
+		pending = status & mask;
 		if (!gpio_handled) {
 			/*
 			 * Dealing with GPIO interrupt
@@ -1206,11 +1216,21 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id)
 		if (!pending)
 			break;
 
+		if (atmel_port->suspended) {
+			atmel_port->pending |= pending;
+			atmel_port->pending_status = status;
+			UART_PUT_IDR(port, mask);
+			pm_system_wakeup();
+			break;
+		}
+
 		atmel_handle_receive(port, pending);
 		atmel_handle_status(port, pending, status);
 		atmel_handle_transmit(port, pending);
 	} while (pass_counter++ < ATMEL_ISR_PASS_LIMIT);
 
+	spin_unlock(&atmel_port->lock_suspended);
+
 	return pass_counter ? IRQ_HANDLED : IRQ_NONE;
 }
 
@@ -1742,7 +1762,8 @@ static int atmel_startup(struct uart_port *port)
 	/*
 	 * Allocate the IRQ
 	 */
-	retval = request_irq(port->irq, atmel_interrupt, IRQF_SHARED,
+	retval = request_irq(port->irq, atmel_interrupt,
+			IRQF_SHARED | IRQF_COND_SUSPEND,
 			tty ? tty->name : "atmel_serial", port);
 	if (retval) {
 		dev_err(port->dev, "atmel_startup - Can't get irq\n");
@@ -2513,8 +2534,14 @@ static int atmel_serial_suspend(struct platform_device *pdev,
 
 	/* we can not wake up if we're running on slow clock */
 	atmel_port->may_wakeup = device_may_wakeup(&pdev->dev);
-	if (atmel_serial_clk_will_stop())
+	if (atmel_serial_clk_will_stop()) {
+		unsigned long flags;
+
+		spin_lock_irqsave(&atmel_port->lock_suspended, flags);
+		atmel_port->suspended = true;
+		spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
 		device_set_wakeup_enable(&pdev->dev, 0);
+	}
 
 	uart_suspend_port(&atmel_uart, port);
 
@@ -2525,6 +2552,18 @@ static int atmel_serial_resume(struct platform_device *pdev)
 {
 	struct uart_port *port = platform_get_drvdata(pdev);
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+	unsigned long flags;
+
+	spin_lock_irqsave(&atmel_port->lock_suspended, flags);
+	if (atmel_port->pending) {
+		atmel_handle_receive(port, atmel_port->pending);
+		atmel_handle_status(port, atmel_port->pending,
+				    atmel_port->pending_status);
+		atmel_handle_transmit(port, atmel_port->pending);
+		atmel_port->pending = 0;
+	}
+	atmel_port->suspended = false;
+	spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
 
 	uart_resume_port(&atmel_uart, port);
 	device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup);
@@ -2593,6 +2632,8 @@ static int atmel_serial_probe(struct platform_device *pdev)
 	port->backup_imr = 0;
 	port->uart.line = ret;
 
+	spin_lock_init(&port->lock_suspended);
+
 	ret = atmel_init_gpios(port, &pdev->dev);
 	if (ret < 0)
 		dev_err(&pdev->dev, "%s",
diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c
index 7ff61e24a195..33fb94f78967 100644
--- a/drivers/tty/serial/of_serial.c
+++ b/drivers/tty/serial/of_serial.c
@@ -133,10 +133,6 @@ static int of_platform_serial_setup(struct platform_device *ofdev,
 	if (of_find_property(np, "no-loopback-test", NULL))
 		port->flags |= UPF_SKIP_TEST;
 
-	ret = of_alias_get_id(np, "serial");
-	if (ret >= 0)
-		port->line = ret;
-
 	port->dev = &ofdev->dev;
 
 	switch (type) {
diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c
index 594b63331ef4..bca975f5093b 100644
--- a/drivers/tty/serial/sprd_serial.c
+++ b/drivers/tty/serial/sprd_serial.c
@@ -293,8 +293,10 @@ static irqreturn_t sprd_handle_irq(int irq, void *dev_id)
 
 	ims = serial_in(port, SPRD_IMSR);
 
-	if (!ims)
+	if (!ims) {
+		spin_unlock(&port->lock);
 		return IRQ_NONE;
+	}
 
 	serial_out(port, SPRD_ICLR, ~0);
 
diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c
index 51f066aa375e..2bb4dfc02873 100644
--- a/drivers/tty/tty_io.c
+++ b/drivers/tty/tty_io.c
@@ -1028,8 +1028,8 @@ EXPORT_SYMBOL(start_tty);
 /* We limit tty time update visibility to every 8 seconds or so. */
 static void tty_update_time(struct timespec *time)
 {
-	unsigned long sec = get_seconds() & ~7;
-	if ((long)(sec - time->tv_sec) > 0)
+	unsigned long sec = get_seconds();
+	if (abs(sec - time->tv_sec) & ~7)
 		time->tv_sec = sec;
 }
 
diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c
index a5cf253b2544..632fc8152061 100644
--- a/drivers/tty/tty_ioctl.c
+++ b/drivers/tty/tty_ioctl.c
@@ -217,11 +217,17 @@ void tty_wait_until_sent(struct tty_struct *tty, long timeout)
 #endif
 	if (!timeout)
 		timeout = MAX_SCHEDULE_TIMEOUT;
-	if (wait_event_interruptible_timeout(tty->write_wait,
-			!tty_chars_in_buffer(tty), timeout) >= 0) {
-		if (tty->ops->wait_until_sent)
-			tty->ops->wait_until_sent(tty, timeout);
-	}
+
+	timeout = wait_event_interruptible_timeout(tty->write_wait,
+			!tty_chars_in_buffer(tty), timeout);
+	if (timeout <= 0)
+		return;
+
+	if (timeout == MAX_SCHEDULE_TIMEOUT)
+		timeout = 0;
+
+	if (tty->ops->wait_until_sent)
+		tty->ops->wait_until_sent(tty, timeout);
 }
 EXPORT_SYMBOL(tty_wait_until_sent);