diff options
Diffstat (limited to 'drivers/usb')
50 files changed, 762 insertions, 333 deletions
diff --git a/drivers/usb/atm/cxacru.c b/drivers/usb/atm/cxacru.c index 8f3b9a0a38e1..1443e9cf631a 100644 --- a/drivers/usb/atm/cxacru.c +++ b/drivers/usb/atm/cxacru.c @@ -1131,7 +1131,10 @@ static int cxacru_bind(struct usbatm_data *usbatm_instance, struct cxacru_data *instance; struct usb_device *usb_dev = interface_to_usbdev(intf); struct usb_host_endpoint *cmd_ep = usb_dev->ep_in[CXACRU_EP_CMD]; - struct usb_endpoint_descriptor *in, *out; + static const u8 ep_addrs[] = { + CXACRU_EP_CMD + USB_DIR_IN, + CXACRU_EP_CMD + USB_DIR_OUT, + 0}; int ret; /* instance init */ @@ -1179,13 +1182,11 @@ static int cxacru_bind(struct usbatm_data *usbatm_instance, } if (usb_endpoint_xfer_int(&cmd_ep->desc)) - ret = usb_find_common_endpoints(intf->cur_altsetting, - NULL, NULL, &in, &out); + ret = usb_check_int_endpoints(intf, ep_addrs); else - ret = usb_find_common_endpoints(intf->cur_altsetting, - &in, &out, NULL, NULL); + ret = usb_check_bulk_endpoints(intf, ep_addrs); - if (ret) { + if (!ret) { usb_err(usbatm_instance, "cxacru_bind: interface has incorrect endpoints\n"); ret = -ENODEV; goto fail; diff --git a/drivers/usb/cdns3/cdns3-gadget.c b/drivers/usb/cdns3/cdns3-gadget.c index 2b8f98f0707e..c12d7f040171 100644 --- a/drivers/usb/cdns3/cdns3-gadget.c +++ b/drivers/usb/cdns3/cdns3-gadget.c @@ -1960,6 +1960,7 @@ static irqreturn_t cdns3_device_thread_irq_handler(int irq, void *data) unsigned int bit; unsigned long reg; + local_bh_disable(); spin_lock_irqsave(&priv_dev->lock, flags); reg = readl(&priv_dev->regs->usb_ists); @@ -2001,6 +2002,7 @@ static irqreturn_t cdns3_device_thread_irq_handler(int irq, void *data) irqend: writel(~0, &priv_dev->regs->ep_ien); spin_unlock_irqrestore(&priv_dev->lock, flags); + local_bh_enable(); return ret; } diff --git a/drivers/usb/cdns3/cdnsp-gadget.c b/drivers/usb/cdns3/cdnsp-gadget.c index d9fb29eb99db..1c29491ee56d 100644 --- a/drivers/usb/cdns3/cdnsp-gadget.c +++ b/drivers/usb/cdns3/cdnsp-gadget.c @@ -138,6 +138,26 @@ static void cdnsp_clear_port_change_bit(struct cdnsp_device *pdev, (portsc & PORT_CHANGE_BITS), port_regs); } +static void cdnsp_set_apb_timeout_value(struct cdnsp_device *pdev) +{ + struct cdns *cdns = dev_get_drvdata(pdev->dev); + __le32 __iomem *reg; + void __iomem *base; + u32 offset = 0; + u32 val; + + if (!cdns->override_apb_timeout) + return; + + base = &pdev->cap_regs->hc_capbase; + offset = cdnsp_find_next_ext_cap(base, offset, D_XEC_PRE_REGS_CAP); + reg = base + offset + REG_CHICKEN_BITS_3_OFFSET; + + val = le32_to_cpu(readl(reg)); + val = CHICKEN_APB_TIMEOUT_SET(val, cdns->override_apb_timeout); + writel(cpu_to_le32(val), reg); +} + static void cdnsp_set_chicken_bits_2(struct cdnsp_device *pdev, u32 bit) { __le32 __iomem *reg; @@ -1779,6 +1799,8 @@ static void cdnsp_get_rev_cap(struct cdnsp_device *pdev) reg += cdnsp_find_next_ext_cap(reg, 0, RTL_REV_CAP); pdev->rev_cap = reg; + pdev->rtl_revision = readl(&pdev->rev_cap->rtl_revision); + dev_info(pdev->dev, "Rev: %08x/%08x, eps: %08x, buff: %08x/%08x\n", readl(&pdev->rev_cap->ctrl_revision), readl(&pdev->rev_cap->rtl_revision), @@ -1804,6 +1826,15 @@ static int cdnsp_gen_setup(struct cdnsp_device *pdev) pdev->hci_version = HC_VERSION(pdev->hcc_params); pdev->hcc_params = readl(&pdev->cap_regs->hcc_params); + /* + * Override the APB timeout value to give the controller more time for + * enabling UTMI clock and synchronizing APB and UTMI clock domains. + * This fix is platform specific and is required to fixes issue with + * reading incorrect value from PORTSC register after resuming + * from L1 state. + */ + cdnsp_set_apb_timeout_value(pdev); + cdnsp_get_rev_cap(pdev); /* Make sure the Device Controller is halted. */ diff --git a/drivers/usb/cdns3/cdnsp-gadget.h b/drivers/usb/cdns3/cdnsp-gadget.h index a61aef0dc273..5cffc1444d3a 100644 --- a/drivers/usb/cdns3/cdnsp-gadget.h +++ b/drivers/usb/cdns3/cdnsp-gadget.h @@ -520,6 +520,9 @@ struct cdnsp_rev_cap { #define REG_CHICKEN_BITS_2_OFFSET 0x48 #define CHICKEN_XDMA_2_TP_CACHE_DIS BIT(28) +#define REG_CHICKEN_BITS_3_OFFSET 0x4C +#define CHICKEN_APB_TIMEOUT_SET(p, val) (((p) & ~GENMASK(21, 0)) | (val)) + /* XBUF Extended Capability ID. */ #define XBUF_CAP_ID 0xCB #define XBUF_RX_TAG_MASK_0_OFFSET 0x1C @@ -1359,6 +1362,7 @@ struct cdnsp_port { * @rev_cap: Controller Capabilities Registers. * @hcs_params1: Cached register copies of read-only HCSPARAMS1 * @hcc_params: Cached register copies of read-only HCCPARAMS1 + * @rtl_revision: Cached controller rtl revision. * @setup: Temporary buffer for setup packet. * @ep0_preq: Internal allocated request used during enumeration. * @ep0_stage: ep0 stage during enumeration process. @@ -1413,6 +1417,8 @@ struct cdnsp_device { __u32 hcs_params1; __u32 hcs_params3; __u32 hcc_params; + #define RTL_REVISION_NEW_LPM 0x2700 + __u32 rtl_revision; /* Lock used in interrupt thread context. */ spinlock_t lock; struct usb_ctrlrequest setup; diff --git a/drivers/usb/cdns3/cdnsp-pci.c b/drivers/usb/cdns3/cdnsp-pci.c index a85db23fa19f..b7a1f28faa1f 100644 --- a/drivers/usb/cdns3/cdnsp-pci.c +++ b/drivers/usb/cdns3/cdnsp-pci.c @@ -33,6 +33,8 @@ #define CDNS_DRD_ID 0x0100 #define CDNS_DRD_IF (PCI_CLASS_SERIAL_USB << 8 | 0x80) +#define CHICKEN_APB_TIMEOUT_VALUE 0x1C20 + static struct pci_dev *cdnsp_get_second_fun(struct pci_dev *pdev) { /* @@ -144,6 +146,14 @@ static int cdnsp_pci_probe(struct pci_dev *pdev, cdnsp->otg_irq = pdev->irq; } + /* + * Cadence PCI based platform require some longer timeout for APB + * to fixes domain clock synchronization issue after resuming + * controller from L1 state. + */ + cdnsp->override_apb_timeout = CHICKEN_APB_TIMEOUT_VALUE; + pci_set_drvdata(pdev, cdnsp); + if (pci_is_enabled(func)) { cdnsp->dev = dev; cdnsp->gadget_init = cdnsp_gadget_init; @@ -153,8 +163,6 @@ static int cdnsp_pci_probe(struct pci_dev *pdev, goto free_cdnsp; } - pci_set_drvdata(pdev, cdnsp); - device_wakeup_enable(&pdev->dev); if (pci_dev_run_wake(pdev)) pm_runtime_put_noidle(&pdev->dev); diff --git a/drivers/usb/cdns3/cdnsp-ring.c b/drivers/usb/cdns3/cdnsp-ring.c index 47096b8e3179..6247584cb939 100644 --- a/drivers/usb/cdns3/cdnsp-ring.c +++ b/drivers/usb/cdns3/cdnsp-ring.c @@ -308,7 +308,8 @@ static bool cdnsp_ring_ep_doorbell(struct cdnsp_device *pdev, writel(db_value, reg_addr); - cdnsp_force_l0_go(pdev); + if (pdev->rtl_revision < RTL_REVISION_NEW_LPM) + cdnsp_force_l0_go(pdev); /* Doorbell was set. */ return true; diff --git a/drivers/usb/cdns3/core.h b/drivers/usb/cdns3/core.h index 7d4b8311051d..847d738b909e 100644 --- a/drivers/usb/cdns3/core.h +++ b/drivers/usb/cdns3/core.h @@ -79,6 +79,8 @@ struct cdns3_platform_data { * @pdata: platform data from glue layer * @lock: spinlock structure * @xhci_plat_data: xhci private data structure pointer + * @override_apb_timeout: hold value of APB timeout. For value 0 the default + * value in CHICKEN_BITS_3 will be preserved. * @gadget_init: pointer to gadget initialization function */ struct cdns { @@ -117,6 +119,7 @@ struct cdns { struct cdns3_platform_data *pdata; spinlock_t lock; struct xhci_plat_priv *xhci_plat_data; + u32 override_apb_timeout; int (*gadget_init)(struct cdns *cdns); }; diff --git a/drivers/usb/chipidea/ci_hdrc_imx.c b/drivers/usb/chipidea/ci_hdrc_imx.c index b0372a3c0ec9..74f0550529ec 100644 --- a/drivers/usb/chipidea/ci_hdrc_imx.c +++ b/drivers/usb/chipidea/ci_hdrc_imx.c @@ -336,6 +336,13 @@ static int ci_hdrc_imx_notify_event(struct ci_hdrc *ci, unsigned int event) return ret; } +static void ci_hdrc_imx_disable_regulator(void *arg) +{ + struct ci_hdrc_imx_data *data = arg; + + regulator_disable(data->hsic_pad_regulator); +} + static int ci_hdrc_imx_probe(struct platform_device *pdev) { struct ci_hdrc_imx_data *data; @@ -370,10 +377,9 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) if (PTR_ERR(data->pinctrl) == -ENODEV) data->pinctrl = NULL; else if (IS_ERR(data->pinctrl)) { - if (PTR_ERR(data->pinctrl) != -EPROBE_DEFER) - dev_err(dev, "pinctrl get failed, err=%ld\n", - PTR_ERR(data->pinctrl)); - return PTR_ERR(data->pinctrl); + ret = dev_err_probe(dev, PTR_ERR(data->pinctrl), + "pinctrl get failed\n"); + goto err_put; } data->hsic_pad_regulator = @@ -382,11 +388,9 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) /* no pad regualator is needed */ data->hsic_pad_regulator = NULL; } else if (IS_ERR(data->hsic_pad_regulator)) { - if (PTR_ERR(data->hsic_pad_regulator) != -EPROBE_DEFER) - dev_err(dev, - "Get HSIC pad regulator error: %ld\n", - PTR_ERR(data->hsic_pad_regulator)); - return PTR_ERR(data->hsic_pad_regulator); + ret = dev_err_probe(dev, PTR_ERR(data->hsic_pad_regulator), + "Get HSIC pad regulator error\n"); + goto err_put; } if (data->hsic_pad_regulator) { @@ -394,7 +398,14 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) if (ret) { dev_err(dev, "Failed to enable HSIC pad regulator\n"); - return ret; + goto err_put; + } + ret = devm_add_action_or_reset(dev, + ci_hdrc_imx_disable_regulator, data); + if (ret) { + dev_err(dev, + "Failed to add regulator devm action\n"); + goto err_put; } } } @@ -408,13 +419,14 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) dev_err(dev, "pinctrl_hsic_idle lookup failed, err=%ld\n", PTR_ERR(pinctrl_hsic_idle)); - return PTR_ERR(pinctrl_hsic_idle); + ret = PTR_ERR(pinctrl_hsic_idle); + goto err_put; } ret = pinctrl_select_state(data->pinctrl, pinctrl_hsic_idle); if (ret) { dev_err(dev, "hsic_idle select failed, err=%d\n", ret); - return ret; + goto err_put; } data->pinctrl_hsic_active = pinctrl_lookup_state(data->pinctrl, @@ -423,7 +435,8 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) dev_err(dev, "pinctrl_hsic_active lookup failed, err=%ld\n", PTR_ERR(data->pinctrl_hsic_active)); - return PTR_ERR(data->pinctrl_hsic_active); + ret = PTR_ERR(data->pinctrl_hsic_active); + goto err_put; } } @@ -433,11 +446,11 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) request_bus_freq(BUS_FREQ_HIGH); ret = imx_get_clks(dev); if (ret) - goto disable_hsic_regulator; + goto qos_remove_request; ret = imx_prepare_enable_clks(dev); if (ret) - goto disable_hsic_regulator; + goto qos_remove_request; ret = clk_prepare_enable(data->clk_wakeup); if (ret) @@ -467,7 +480,11 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) of_usb_get_phy_mode(np) == USBPHY_INTERFACE_MODE_ULPI) { pdata.flags |= CI_HDRC_OVERRIDE_PHY_CONTROL; data->override_phy_control = true; - usb_phy_init(pdata.usb_phy); + ret = usb_phy_init(pdata.usb_phy); + if (ret) { + dev_err(dev, "Failed to init phy\n"); + goto err_clk; + } } if (pdata.flags & CI_HDRC_SUPPORTS_RUNTIME_PM) @@ -481,7 +498,7 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) ret = imx_usbmisc_init(data->usbmisc_data); if (ret) { dev_err(dev, "usbmisc init failed, ret=%d\n", ret); - goto err_clk; + goto phy_shutdown; } data->ci_pdev = ci_hdrc_add_device(dev, @@ -489,10 +506,8 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) &pdata); if (IS_ERR(data->ci_pdev)) { ret = PTR_ERR(data->ci_pdev); - if (ret != -EPROBE_DEFER) - dev_err(dev, "ci_hdrc_add_device failed, err=%d\n", - ret); - goto err_clk; + dev_err_probe(dev, ret, "ci_hdrc_add_device failed\n"); + goto phy_shutdown; } if (data->usbmisc_data) { @@ -526,22 +541,24 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) disable_device: ci_hdrc_remove_device(data->ci_pdev); +phy_shutdown: + if (data->override_phy_control) + usb_phy_shutdown(data->phy); err_clk: clk_disable_unprepare(data->clk_wakeup); err_wakeup_clk: imx_disable_unprepare_clks(dev); -disable_hsic_regulator: - release_bus_freq(BUS_FREQ_HIGH); - if (data->hsic_pad_regulator) - /* don't overwrite original ret (cf. EPROBE_DEFER) */ - regulator_disable(data->hsic_pad_regulator); +qos_remove_request: if (pdata.flags & CI_HDRC_PMQOS) cpu_latency_qos_remove_request(&data->pm_qos_req); data->ci_pdev = NULL; +err_put: + if (data->usbmisc_data) + put_device(data->usbmisc_data->dev); return ret; } -static int ci_hdrc_imx_remove(struct platform_device *pdev) +static void ci_hdrc_imx_remove(struct platform_device *pdev) { struct ci_hdrc_imx_data *data = platform_get_drvdata(pdev); @@ -560,11 +577,9 @@ static int ci_hdrc_imx_remove(struct platform_device *pdev) release_bus_freq(BUS_FREQ_HIGH); if (data->plat_data->flags & CI_HDRC_PMQOS) cpu_latency_qos_remove_request(&data->pm_qos_req); - if (data->hsic_pad_regulator) - regulator_disable(data->hsic_pad_regulator); } - - return 0; + if (data->usbmisc_data) + put_device(data->usbmisc_data->dev); } static void ci_hdrc_imx_shutdown(struct platform_device *pdev) @@ -689,7 +704,7 @@ static const struct dev_pm_ops ci_hdrc_imx_pm_ops = { }; static struct platform_driver ci_hdrc_imx_driver = { .probe = ci_hdrc_imx_probe, - .remove = ci_hdrc_imx_remove, + .remove_new = ci_hdrc_imx_remove, .shutdown = ci_hdrc_imx_shutdown, .driver = { .name = "imx_usb", diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 4871d0f09f6b..48be3c4f02a3 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -360,7 +360,7 @@ static void acm_process_notification(struct acm *acm, unsigned char *buf) static void acm_ctrl_irq(struct urb *urb) { struct acm *acm = urb->context; - struct usb_cdc_notification *dr = urb->transfer_buffer; + struct usb_cdc_notification *dr; unsigned int current_size = urb->actual_length; unsigned int expected_size, copy_size, alloc_size; int retval; @@ -387,14 +387,25 @@ static void acm_ctrl_irq(struct urb *urb) usb_mark_last_busy(acm->dev); - if (acm->nb_index) + if (acm->nb_index == 0) { + /* + * The first chunk of a message must contain at least the + * notification header with the length field, otherwise we + * can't get an expected_size. + */ + if (current_size < sizeof(struct usb_cdc_notification)) { + dev_dbg(&acm->control->dev, "urb too short\n"); + goto exit; + } + dr = urb->transfer_buffer; + } else { dr = (struct usb_cdc_notification *)acm->notification_buffer; - + } /* size = notification-header + (optional) data */ expected_size = sizeof(struct usb_cdc_notification) + le16_to_cpu(dr->wLength); - if (current_size < expected_size) { + if (acm->nb_index != 0 || current_size < expected_size) { /* notification is transmitted fragmented, reassemble */ if (acm->nb_size < expected_size) { u8 *new_buffer; @@ -1707,13 +1718,16 @@ static const struct usb_device_id acm_ids[] = { { USB_DEVICE(0x0870, 0x0001), /* Metricom GS Modem */ .driver_info = NO_UNION_NORMAL, /* has no union descriptor */ }, - { USB_DEVICE(0x045b, 0x023c), /* Renesas USB Download mode */ + { USB_DEVICE(0x045b, 0x023c), /* Renesas R-Car H3 USB Download mode */ + .driver_info = DISABLE_ECHO, /* Don't echo banner */ + }, + { USB_DEVICE(0x045b, 0x0247), /* Renesas R-Car D3 USB Download mode */ .driver_info = DISABLE_ECHO, /* Don't echo banner */ }, - { USB_DEVICE(0x045b, 0x0248), /* Renesas USB Download mode */ + { USB_DEVICE(0x045b, 0x0248), /* Renesas R-Car M3-N USB Download mode */ .driver_info = DISABLE_ECHO, /* Don't echo banner */ }, - { USB_DEVICE(0x045b, 0x024D), /* Renesas USB Download mode */ + { USB_DEVICE(0x045b, 0x024D), /* Renesas R-Car E3 USB Download mode */ .driver_info = DISABLE_ECHO, /* Don't echo banner */ }, { USB_DEVICE(0x0e8d, 0x0003), /* FIREFLY, MediaTek Inc; andrey.arapov@gmail.com */ diff --git a/drivers/usb/class/cdc-wdm.c b/drivers/usb/class/cdc-wdm.c index d85606bad562..a4be6dba756b 100644 --- a/drivers/usb/class/cdc-wdm.c +++ b/drivers/usb/class/cdc-wdm.c @@ -726,7 +726,7 @@ static int wdm_open(struct inode *inode, struct file *file) rv = -EBUSY; goto out; } - + smp_rmb(); /* ordered against wdm_wwan_port_stop() */ rv = usb_autopm_get_interface(desc->intf); if (rv < 0) { dev_err(&desc->intf->dev, "Error autopm - %d\n", rv); @@ -829,6 +829,7 @@ static struct usb_class_driver wdm_class = { static int wdm_wwan_port_start(struct wwan_port *port) { struct wdm_device *desc = wwan_port_get_drvdata(port); + int rv; /* The interface is both exposed via the WWAN framework and as a * legacy usbmisc chardev. If chardev is already open, just fail @@ -848,7 +849,15 @@ static int wdm_wwan_port_start(struct wwan_port *port) wwan_port_txon(port); /* Start getting events */ - return usb_submit_urb(desc->validity, GFP_KERNEL); + rv = usb_submit_urb(desc->validity, GFP_KERNEL); + if (rv < 0) { + wwan_port_txoff(port); + desc->manage_power(desc->intf, 0); + /* this must be last lest we race with chardev open */ + clear_bit(WDM_WWAN_IN_USE, &desc->flags); + } + + return rv; } static void wdm_wwan_port_stop(struct wwan_port *port) @@ -859,8 +868,10 @@ static void wdm_wwan_port_stop(struct wwan_port *port) poison_urbs(desc); desc->manage_power(desc->intf, 0); clear_bit(WDM_READ, &desc->flags); - clear_bit(WDM_WWAN_IN_USE, &desc->flags); unpoison_urbs(desc); + smp_wmb(); /* ordered against wdm_open() */ + /* this must be last lest we open a poisoned device */ + clear_bit(WDM_WWAN_IN_USE, &desc->flags); } static void wdm_wwan_port_tx_complete(struct urb *urb) @@ -868,7 +879,7 @@ static void wdm_wwan_port_tx_complete(struct urb *urb) struct sk_buff *skb = urb->context; struct wdm_device *desc = skb_shinfo(skb)->destructor_arg; - usb_autopm_put_interface(desc->intf); + usb_autopm_put_interface_async(desc->intf); wwan_port_txon(desc->wwanp); kfree_skb(skb); } @@ -898,7 +909,7 @@ static int wdm_wwan_port_tx(struct wwan_port *port, struct sk_buff *skb) req->bRequestType = (USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE); req->bRequest = USB_CDC_SEND_ENCAPSULATED_COMMAND; req->wValue = 0; - req->wIndex = desc->inum; + req->wIndex = desc->inum; /* already converted */ req->wLength = cpu_to_le16(skb->len); skb_shinfo(skb)->destructor_arg = desc; diff --git a/drivers/usb/class/usbtmc.c b/drivers/usb/class/usbtmc.c index c2e666e82857..2f92905e05ca 100644 --- a/drivers/usb/class/usbtmc.c +++ b/drivers/usb/class/usbtmc.c @@ -482,6 +482,7 @@ static int usbtmc_get_stb(struct usbtmc_file_data *file_data, __u8 *stb) u8 *buffer; u8 tag; int rv; + long wait_rv; dev_dbg(dev, "Enter ioctl_read_stb iin_ep_present: %d\n", data->iin_ep_present); @@ -511,16 +512,17 @@ static int usbtmc_get_stb(struct usbtmc_file_data *file_data, __u8 *stb) } if (data->iin_ep_present) { - rv = wait_event_interruptible_timeout( + wait_rv = wait_event_interruptible_timeout( data->waitq, atomic_read(&data->iin_data_valid) != 0, file_data->timeout); - if (rv < 0) { - dev_dbg(dev, "wait interrupted %d\n", rv); + if (wait_rv < 0) { + dev_dbg(dev, "wait interrupted %ld\n", wait_rv); + rv = wait_rv; goto exit; } - if (rv == 0) { + if (wait_rv == 0) { dev_dbg(dev, "wait timed out\n"); rv = -ETIMEDOUT; goto exit; @@ -539,6 +541,8 @@ static int usbtmc_get_stb(struct usbtmc_file_data *file_data, __u8 *stb) dev_dbg(dev, "stb:0x%02x received %d\n", (unsigned int)*stb, rv); + rv = 0; + exit: /* bump interrupt bTag */ data->iin_bTag += 1; @@ -602,9 +606,9 @@ static int usbtmc488_ioctl_wait_srq(struct usbtmc_file_data *file_data, { struct usbtmc_device_data *data = file_data->data; struct device *dev = &data->intf->dev; - int rv; u32 timeout; unsigned long expire; + long wait_rv; if (!data->iin_ep_present) { dev_dbg(dev, "no interrupt endpoint present\n"); @@ -618,25 +622,24 @@ static int usbtmc488_ioctl_wait_srq(struct usbtmc_file_data *file_data, mutex_unlock(&data->io_mutex); - rv = wait_event_interruptible_timeout( - data->waitq, - atomic_read(&file_data->srq_asserted) != 0 || - atomic_read(&file_data->closing), - expire); + wait_rv = wait_event_interruptible_timeout( + data->waitq, + atomic_read(&file_data->srq_asserted) != 0 || + atomic_read(&file_data->closing), + expire); mutex_lock(&data->io_mutex); /* Note! disconnect or close could be called in the meantime */ if (atomic_read(&file_data->closing) || data->zombie) - rv = -ENODEV; + return -ENODEV; - if (rv < 0) { - /* dev can be invalid now! */ - pr_debug("%s - wait interrupted %d\n", __func__, rv); - return rv; + if (wait_rv < 0) { + dev_dbg(dev, "%s - wait interrupted %ld\n", __func__, wait_rv); + return wait_rv; } - if (rv == 0) { + if (wait_rv == 0) { dev_dbg(dev, "%s - wait timed out\n", __func__); return -ETIMEDOUT; } @@ -830,6 +833,7 @@ static ssize_t usbtmc_generic_read(struct usbtmc_file_data *file_data, unsigned long expire; int bufcount = 1; int again = 0; + long wait_rv; /* mutex already locked */ @@ -942,19 +946,24 @@ static ssize_t usbtmc_generic_read(struct usbtmc_file_data *file_data, if (!(flags & USBTMC_FLAG_ASYNC)) { dev_dbg(dev, "%s: before wait time %lu\n", __func__, expire); - retval = wait_event_interruptible_timeout( + wait_rv = wait_event_interruptible_timeout( file_data->wait_bulk_in, usbtmc_do_transfer(file_data), expire); - dev_dbg(dev, "%s: wait returned %d\n", - __func__, retval); + dev_dbg(dev, "%s: wait returned %ld\n", + __func__, wait_rv); + + if (wait_rv < 0) { + retval = wait_rv; + goto error; + } - if (retval <= 0) { - if (retval == 0) - retval = -ETIMEDOUT; + if (wait_rv == 0) { + retval = -ETIMEDOUT; goto error; } + } urb = usb_get_from_anchor(&file_data->in_anchor); @@ -1380,7 +1389,10 @@ static ssize_t usbtmc_read(struct file *filp, char __user *buf, if (!buffer) return -ENOMEM; - mutex_lock(&data->io_mutex); + retval = mutex_lock_interruptible(&data->io_mutex); + if (retval < 0) + goto exit_nolock; + if (data->zombie) { retval = -ENODEV; goto exit; @@ -1503,6 +1515,7 @@ static ssize_t usbtmc_read(struct file *filp, char __user *buf, exit: mutex_unlock(&data->io_mutex); +exit_nolock: kfree(buffer); return retval; } diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 2c7645f8a7f0..f23b689cc995 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -1807,6 +1807,17 @@ static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id) hdev = interface_to_usbdev(intf); /* + * The USB 2.0 spec prohibits hubs from having more than one + * configuration or interface, and we rely on this prohibition. + * Refuse to accept a device that violates it. + */ + if (hdev->descriptor.bNumConfigurations > 1 || + hdev->actconfig->desc.bNumInterfaces > 1) { + dev_err(&intf->dev, "Invalid hub with more than one config or interface\n"); + return -EINVAL; + } + + /* * Set default autosuspend delay as 0 to speedup bus suspend, * based on the below considerations: * @@ -4638,7 +4649,6 @@ void usb_ep0_reinit(struct usb_device *udev) EXPORT_SYMBOL_GPL(usb_ep0_reinit); #define usb_sndaddr0pipe() (PIPE_CONTROL << 30) -#define usb_rcvaddr0pipe() ((PIPE_CONTROL << 30) | USB_DIR_IN) static int hub_set_address(struct usb_device *udev, int devnum) { @@ -4656,7 +4666,7 @@ static int hub_set_address(struct usb_device *udev, int devnum) if (udev->state != USB_STATE_DEFAULT) return -EINVAL; if (hcd->driver->address_device) - retval = hcd->driver->address_device(hcd, udev); + retval = hcd->driver->address_device(hcd, udev, USB_CTRL_SET_TIMEOUT); else retval = usb_control_msg(udev, usb_sndaddr0pipe(), USB_REQ_SET_ADDRESS, 0, devnum, 0, @@ -4711,6 +4721,67 @@ static int hub_enable_device(struct usb_device *udev) return hcd->driver->enable_device(hcd, udev); } +/* + * Get the bMaxPacketSize0 value during initialization by reading the + * device's device descriptor. Since we don't already know this value, + * the transfer is unsafe and it ignores I/O errors, only testing for + * reasonable received values. + * + * For "old scheme" initialization, size will be 8 so we read just the + * start of the device descriptor, which should work okay regardless of + * the actual bMaxPacketSize0 value. For "new scheme" initialization, + * size will be 64 (and buf will point to a sufficiently large buffer), + * which might not be kosher according to the USB spec but it's what + * Windows does and what many devices expect. + * + * Returns: bMaxPacketSize0 or a negative error code. + */ +static int get_bMaxPacketSize0(struct usb_device *udev, + struct usb_device_descriptor *buf, int size, bool first_time) +{ + int i, rc; + + /* + * Retry on all errors; some devices are flakey. + * 255 is for WUSB devices, we actually need to use + * 512 (WUSB1.0[4.8.1]). + */ + for (i = 0; i < GET_MAXPACKET0_TRIES; ++i) { + /* Start with invalid values in case the transfer fails */ + buf->bDescriptorType = buf->bMaxPacketSize0 = 0; + rc = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), + USB_REQ_GET_DESCRIPTOR, USB_DIR_IN, + USB_DT_DEVICE << 8, 0, + buf, size, + initial_descriptor_timeout); + switch (buf->bMaxPacketSize0) { + case 8: case 16: case 32: case 64: case 9: + if (buf->bDescriptorType == USB_DT_DEVICE) { + rc = buf->bMaxPacketSize0; + break; + } + fallthrough; + default: + if (rc >= 0) + rc = -EPROTO; + break; + } + + /* + * Some devices time out if they are powered on + * when already connected. They need a second + * reset, so return early. But only on the first + * attempt, lest we get into a time-out/reset loop. + */ + if (rc > 0 || (rc == -ETIMEDOUT && first_time && + udev->speed > USB_SPEED_FULL)) + break; + } + return rc; +} + +#define GET_DESCRIPTOR_BUFSIZE 64 + /* Reset device, (re)assign address, get device descriptor. * Device connection must be stable, no more debouncing needed. * Returns device in USB_STATE_ADDRESS, except on error. @@ -4735,6 +4806,12 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, int devnum = udev->devnum; const char *driver_name; bool do_new_scheme; + int maxp0; + struct usb_device_descriptor *buf; + + buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO); + if (!buf) + return -ENOMEM; /* root hub ports have a slightly longer reset period * (from USB 2.0 spec, section 7.1.7.5) @@ -4849,9 +4926,6 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, for (retries = 0; retries < GET_DESCRIPTOR_TRIES; (++retries, msleep(100))) { if (do_new_scheme) { - struct usb_device_descriptor *buf; - int r = 0; - retval = hub_enable_device(udev); if (retval < 0) { dev_err(&udev->dev, @@ -4860,52 +4934,8 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, goto fail; } -#define GET_DESCRIPTOR_BUFSIZE 64 - buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO); - if (!buf) { - retval = -ENOMEM; - continue; - } - - /* Retry on all errors; some devices are flakey. - * 255 is for WUSB devices, we actually need to use - * 512 (WUSB1.0[4.8.1]). - */ - for (operations = 0; operations < GET_MAXPACKET0_TRIES; - ++operations) { - buf->bMaxPacketSize0 = 0; - r = usb_control_msg(udev, usb_rcvaddr0pipe(), - USB_REQ_GET_DESCRIPTOR, USB_DIR_IN, - USB_DT_DEVICE << 8, 0, - buf, GET_DESCRIPTOR_BUFSIZE, - initial_descriptor_timeout); - switch (buf->bMaxPacketSize0) { - case 8: case 16: case 32: case 64: case 255: - if (buf->bDescriptorType == - USB_DT_DEVICE) { - r = 0; - break; - } - fallthrough; - default: - if (r == 0) - r = -EPROTO; - break; - } - /* - * Some devices time out if they are powered on - * when already connected. They need a second - * reset. But only on the first attempt, - * lest we get into a time out/reset loop - */ - if (r == 0 || (r == -ETIMEDOUT && - retries == 0 && - udev->speed > USB_SPEED_FULL)) - break; - } - udev->descriptor.bMaxPacketSize0 = - buf->bMaxPacketSize0; - kfree(buf); + maxp0 = get_bMaxPacketSize0(udev, buf, + GET_DESCRIPTOR_BUFSIZE, retries == 0); retval = hub_port_reset(hub, port1, udev, delay, false); if (retval < 0) /* error or disconnect */ @@ -4916,15 +4946,14 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, retval = -ENODEV; goto fail; } - if (r) { - if (r != -ENODEV) + if (maxp0 < 0) { + if (maxp0 != -ENODEV) dev_err(&udev->dev, "device no response, device descriptor read/64, error %d\n", - r); - retval = -EMSGSIZE; + maxp0); + retval = maxp0; continue; } -#undef GET_DESCRIPTOR_BUFSIZE } /* @@ -4969,20 +4998,17 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, if (do_new_scheme) break; } - - retval = usb_get_device_descriptor(udev, 8); - if (retval < 8) { + /* !do_new_scheme || wusb */ + maxp0 = get_bMaxPacketSize0(udev, buf, 8, retries == 0); + if (maxp0 < 0) { + retval = maxp0; if (retval != -ENODEV) dev_err(&udev->dev, "device descriptor read/8, error %d\n", retval); - if (retval >= 0) - retval = -EMSGSIZE; } else { u32 delay; - retval = 0; - delay = udev->parent->hub_delay; udev->hub_delay = min_t(u32, delay, USB_TP_TRANSMISSION_DELAY_MAX); @@ -4999,27 +5025,10 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, if (retval) goto fail; - /* - * Some superspeed devices have finished the link training process - * and attached to a superspeed hub port, but the device descriptor - * got from those devices show they aren't superspeed devices. Warm - * reset the port attached by the devices can fix them. - */ - if ((udev->speed >= USB_SPEED_SUPER) && - (le16_to_cpu(udev->descriptor.bcdUSB) < 0x0300)) { - dev_err(&udev->dev, "got a wrong device descriptor, " - "warm reset device\n"); - hub_port_reset(hub, port1, udev, - HUB_BH_RESET_TIME, true); - retval = -EINVAL; - goto fail; - } - - if (udev->descriptor.bMaxPacketSize0 == 0xff || - udev->speed >= USB_SPEED_SUPER) + if (maxp0 == 0xff || udev->speed >= USB_SPEED_SUPER) i = 512; else - i = udev->descriptor.bMaxPacketSize0; + i = maxp0; if (usb_endpoint_maxp(&udev->ep0.desc) != i) { if (udev->speed == USB_SPEED_LOW || !(i == 8 || i == 16 || i == 32 || i == 64)) { @@ -5045,6 +5054,20 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, goto fail; } + /* + * Some superspeed devices have finished the link training process + * and attached to a superspeed hub port, but the device descriptor + * got from those devices show they aren't superspeed devices. Warm + * reset the port attached by the devices can fix them. + */ + if ((udev->speed >= USB_SPEED_SUPER) && + (le16_to_cpu(udev->descriptor.bcdUSB) < 0x0300)) { + dev_err(&udev->dev, "got a wrong device descriptor, warm reset device\n"); + hub_port_reset(hub, port1, udev, HUB_BH_RESET_TIME, true); + retval = -EINVAL; + goto fail; + } + usb_detect_quirks(udev); if (udev->wusb == 0 && le16_to_cpu(udev->descriptor.bcdUSB) >= 0x0201) { @@ -5065,6 +5088,7 @@ fail: hub_port_disable(hub, port1, 0); update_devnum(udev, devnum); /* for disconnect processing */ } + kfree(buf); return retval; } @@ -5912,6 +5936,36 @@ void usb_hub_cleanup(void) } /* usb_hub_cleanup() */ /** + * hub_hc_release_resources - clear resources used by host controller + * @udev: pointer to device being released + * + * Context: task context, might sleep + * + * Function releases the host controller resources in correct order before + * making any operation on resuming usb device. The host controller resources + * allocated for devices in tree should be released starting from the last + * usb device in tree toward the root hub. This function is used only during + * resuming device when usb device require reinitialization – that is, when + * flag udev->reset_resume is set. + * + * This call is synchronous, and may not be used in an interrupt context. + */ +static void hub_hc_release_resources(struct usb_device *udev) +{ + struct usb_hub *hub = usb_hub_to_struct_hub(udev); + struct usb_hcd *hcd = bus_to_hcd(udev->bus); + int i; + + /* Release up resources for all children before this device */ + for (i = 0; i < udev->maxchild; i++) + if (hub->ports[i]->child) + hub_hc_release_resources(hub->ports[i]->child); + + if (hcd->driver->reset_device) + hcd->driver->reset_device(hcd, udev); +} + +/** * usb_reset_and_verify_device - perform a USB port reset to reinitialize a device * @udev: device to reset (not in SUSPENDED or NOTATTACHED state) * @@ -5985,6 +6039,9 @@ static int usb_reset_and_verify_device(struct usb_device *udev) bos = udev->bos; udev->bos = NULL; + if (udev->reset_resume) + hub_hc_release_resources(udev); + mutex_lock(hcd->address0_mutex); for (i = 0; i < PORT_INIT_TRIES; ++i) { diff --git a/drivers/usb/core/quirks.c b/drivers/usb/core/quirks.c index 6b21afb465fb..491d209e7e69 100644 --- a/drivers/usb/core/quirks.c +++ b/drivers/usb/core/quirks.c @@ -338,6 +338,10 @@ static const struct usb_device_id usb_quirk_list[] = { { USB_DEVICE(0x0638, 0x0a13), .driver_info = USB_QUIRK_STRING_FETCH_255 }, + /* Prolific Single-LUN Mass Storage Card Reader */ + { USB_DEVICE(0x067b, 0x2731), .driver_info = USB_QUIRK_DELAY_INIT | + USB_QUIRK_NO_LPM }, + /* Saitek Cyborg Gold Joystick */ { USB_DEVICE(0x06a3, 0x0006), .driver_info = USB_QUIRK_CONFIG_INTF_STRINGS }, @@ -362,6 +366,9 @@ static const struct usb_device_id usb_quirk_list[] = { { USB_DEVICE(0x0781, 0x5583), .driver_info = USB_QUIRK_NO_LPM }, { USB_DEVICE(0x0781, 0x5591), .driver_info = USB_QUIRK_NO_LPM }, + /* SanDisk Corp. SanDisk 3.2Gen1 */ + { USB_DEVICE(0x0781, 0x55a3), .driver_info = USB_QUIRK_DELAY_INIT }, + /* Realforce 87U Keyboard */ { USB_DEVICE(0x0853, 0x011b), .driver_info = USB_QUIRK_NO_LPM }, @@ -376,6 +383,9 @@ static const struct usb_device_id usb_quirk_list[] = { { USB_DEVICE(0x0904, 0x6103), .driver_info = USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL }, + /* Silicon Motion Flash Drive */ + { USB_DEVICE(0x090c, 0x1000), .driver_info = USB_QUIRK_DELAY_INIT }, + /* Sound Devices USBPre2 */ { USB_DEVICE(0x0926, 0x0202), .driver_info = USB_QUIRK_ENDPOINT_IGNORE }, @@ -429,6 +439,9 @@ static const struct usb_device_id usb_quirk_list[] = { { USB_DEVICE(0x0c45, 0x7056), .driver_info = USB_QUIRK_IGNORE_REMOTE_WAKEUP }, + /* Sony Xperia XZ1 Compact (lilac) smartphone in fastboot mode */ + { USB_DEVICE(0x0fce, 0x0dde), .driver_info = USB_QUIRK_NO_LPM }, + /* Action Semiconductor flash disk */ { USB_DEVICE(0x10d6, 0x2200), .driver_info = USB_QUIRK_STRING_FETCH_255 }, @@ -519,10 +532,16 @@ static const struct usb_device_id usb_quirk_list[] = { /* Blackmagic Design UltraStudio SDI */ { USB_DEVICE(0x1edb, 0xbd4f), .driver_info = USB_QUIRK_NO_LPM }, + /* Teclast disk */ + { USB_DEVICE(0x1f75, 0x0917), .driver_info = USB_QUIRK_NO_LPM }, + /* Hauppauge HVR-950q */ { USB_DEVICE(0x2040, 0x7200), .driver_info = USB_QUIRK_CONFIG_INTF_STRINGS }, + /* VLI disk */ + { USB_DEVICE(0x2109, 0x0711), .driver_info = USB_QUIRK_NO_LPM }, + /* Raydium Touchscreen */ { USB_DEVICE(0x2386, 0x3114), .driver_info = USB_QUIRK_NO_LPM }, diff --git a/drivers/usb/dwc2/gadget.c b/drivers/usb/dwc2/gadget.c index 4422da561365..7d8523398e19 100644 --- a/drivers/usb/dwc2/gadget.c +++ b/drivers/usb/dwc2/gadget.c @@ -4613,6 +4613,7 @@ static int dwc2_hsotg_udc_stop(struct usb_gadget *gadget) spin_lock_irqsave(&hsotg->lock, flags); hsotg->driver = NULL; + hsotg->gadget.dev.of_node = NULL; hsotg->gadget.speed = USB_SPEED_UNKNOWN; hsotg->enabled = 0; diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index 5971d0f1d04e..47f81a0b0022 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -123,8 +123,9 @@ void dwc3_enable_susphy(struct dwc3 *dwc, bool enable) dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); } -void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode) +void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode, bool ignore_susphy) { + unsigned int hw_mode; u32 reg, reg_mode; /* Set PRTCAPDIR to be device mode for disconnect */ @@ -134,6 +135,18 @@ void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode) reg_mode = mode; reg = dwc3_readl(dwc->regs, DWC3_GCTL); + + /* + * For DRD controllers, GUSB3PIPECTL.SUSPENDENABLE and + * GUSB2PHYCFG.SUSPHY should be cleared during mode switching, + * and they can be set after core initialization. + */ + hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0); + if (hw_mode == DWC3_GHWPARAMS0_MODE_DRD && !ignore_susphy) { + if (DWC3_GCTL_PRTCAP(reg) != mode) + dwc3_enable_susphy(dwc, false); + } + reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG)); reg |= DWC3_GCTL_PRTCAPDIR(reg_mode); dwc3_writel(dwc->regs, DWC3_GCTL, reg); @@ -214,7 +227,7 @@ static void __dwc3_set_mode(struct work_struct *work) spin_lock_irqsave(&dwc->lock, flags); - dwc3_set_prtcap(dwc, desired_dr_role); + dwc3_set_prtcap(dwc, desired_dr_role, false); spin_unlock_irqrestore(&dwc->lock, flags); @@ -717,16 +730,7 @@ static int dwc3_phy_setup(struct dwc3 *dwc) */ reg &= ~DWC3_GUSB3PIPECTL_UX_EXIT_PX; - /* - * Above DWC_usb3.0 1.94a, it is recommended to set - * DWC3_GUSB3PIPECTL_SUSPHY to '0' during coreConsultant configuration. - * So default value will be '0' when the core is reset. Application - * needs to set it to '1' after the core initialization is completed. - * - * Similarly for DRD controllers, GUSB3PIPECTL.SUSPENDENABLE must be - * cleared after power-on reset, and it can be set after core - * initialization. - */ + /* Ensure the GUSB3PIPECTL.SUSPENDENABLE is cleared prior to phy init. */ reg &= ~DWC3_GUSB3PIPECTL_SUSPHY; if (dwc->u2ss_inp3_quirk) @@ -799,15 +803,7 @@ static int dwc3_phy_setup(struct dwc3 *dwc) break; } - /* - * Above DWC_usb3.0 1.94a, it is recommended to set - * DWC3_GUSB2PHYCFG_SUSPHY to '0' during coreConsultant configuration. - * So default value will be '0' when the core is reset. Application - * needs to set it to '1' after the core initialization is completed. - * - * Similarly for DRD controllers, GUSB2PHYCFG.SUSPHY must be cleared - * after power-on reset, and it can be set after core initialization. - */ + /* Ensure the GUSB2PHYCFG.SUSPHY is cleared prior to phy init. */ reg &= ~DWC3_GUSB2PHYCFG_SUSPHY; if (dwc->dis_enblslpm_quirk) @@ -1307,6 +1303,25 @@ static int dwc3_core_init(struct dwc3 *dwc) dwc->core_inited = true; + /* + * Above DWC_usb3.0 1.94a, it is recommended to set + * DWC3_GUSB3PIPECTL_SUSPHY and DWC3_GUSB2PHYCFG_SUSPHY to '0' during + * coreConsultant configuration. So default value will be '0' when the + * core is reset. Application needs to set it to '1' after the core + * initialization is completed. + * + * Certain phy requires to be in P0 power state during initialization. + * Make sure GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY are clear + * prior to phy init to maintain in the P0 state. + * + * After phy initialization, some phy operations can only be executed + * while in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and + * GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid + * blocking phy ops. + */ + if (!DWC3_VER_IS_WITHIN(DWC3, ANY, 194A)) + dwc3_enable_susphy(dwc, true); + return 0; err4: @@ -1395,7 +1410,7 @@ static int dwc3_core_init_mode(struct dwc3 *dwc) switch (dwc->dr_mode) { case USB_DR_MODE_PERIPHERAL: - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE, false); if (dwc->usb2_phy) otg_set_vbus(dwc->usb2_phy->otg, false); @@ -1407,7 +1422,7 @@ static int dwc3_core_init_mode(struct dwc3 *dwc) return dev_err_probe(dev, ret, "failed to initialize gadget\n"); break; case USB_DR_MODE_HOST: - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST, false); if (dwc->usb2_phy) otg_set_vbus(dwc->usb2_phy->otg, true); @@ -1454,7 +1469,7 @@ static void dwc3_core_exit_mode(struct dwc3 *dwc) } /* de-assert DRVVBUS for HOST and OTG mode */ - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE, true); } static void dwc3_get_properties(struct dwc3 *dwc) @@ -1468,8 +1483,6 @@ static void dwc3_get_properties(struct dwc3 *dwc) u8 tx_thr_num_pkt_prd = 0; u8 tx_max_burst_prd = 0; u8 tx_fifo_resize_max_num; - const char *usb_psy_name; - int ret; /* default to highest possible threshold */ lpm_nyet_threshold = 0xf; @@ -1513,13 +1526,6 @@ static void dwc3_get_properties(struct dwc3 *dwc) else dwc->sysdev = dwc->dev; - ret = device_property_read_string(dev, "usb-psy-name", &usb_psy_name); - if (ret >= 0) { - dwc->usb_psy = power_supply_get_by_name(usb_psy_name); - if (!dwc->usb_psy) - dev_err(dev, "couldn't get usb power supply\n"); - } - dwc->has_lpm_erratum = device_property_read_bool(dev, "snps,has-lpm-erratum"); device_property_read_u8(dev, "snps,lpm-nyet-threshold", @@ -1618,8 +1624,6 @@ static void dwc3_get_properties(struct dwc3 *dwc) dwc->tx_thr_num_pkt_prd = tx_thr_num_pkt_prd; dwc->tx_max_burst_prd = tx_max_burst_prd; - dwc->imod_interval = 0; - dwc->tx_fifo_resize_max_num = tx_fifo_resize_max_num; } @@ -1637,21 +1641,19 @@ static void dwc3_check_params(struct dwc3 *dwc) unsigned int hwparam_gen = DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3); - /* Check for proper value of imod_interval */ - if (dwc->imod_interval && !dwc3_has_imod(dwc)) { - dev_warn(dwc->dev, "Interrupt moderation not supported\n"); - dwc->imod_interval = 0; - } - /* + * Enable IMOD for all supporting controllers. + * + * Particularly, DWC_usb3 v3.00a must enable this feature for + * the following reason: + * * Workaround for STAR 9000961433 which affects only version * 3.00a of the DWC_usb3 core. This prevents the controller * interrupt from being masked while handling events. IMOD * allows us to work around this issue. Enable it for the * affected version. */ - if (!dwc->imod_interval && - DWC3_VER_IS(DWC3, 300A)) + if (dwc3_has_imod((dwc))) dwc->imod_interval = 1; /* Check the maximum_speed parameter */ @@ -1732,6 +1734,23 @@ static void dwc3_check_params(struct dwc3 *dwc) } } +static struct power_supply *dwc3_get_usb_power_supply(struct dwc3 *dwc) +{ + struct power_supply *usb_psy; + const char *usb_psy_name; + int ret; + + ret = device_property_read_string(dwc->dev, "usb-psy-name", &usb_psy_name); + if (ret < 0) + return NULL; + + usb_psy = power_supply_get_by_name(usb_psy_name); + if (!usb_psy) + return ERR_PTR(-EPROBE_DEFER); + + return usb_psy; +} + static int dwc3_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -1776,6 +1795,10 @@ static int dwc3_probe(struct platform_device *pdev) dwc3_get_properties(dwc); + dwc->usb_psy = dwc3_get_usb_power_supply(dwc); + if (IS_ERR(dwc->usb_psy)) + return dev_err_probe(dev, PTR_ERR(dwc->usb_psy), "couldn't get usb power supply\n"); + dwc->reset = devm_reset_control_array_get_optional_shared(dev); if (IS_ERR(dwc->reset)) return PTR_ERR(dwc->reset); @@ -2060,7 +2083,7 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) if (ret) return ret; - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE, true); dwc3_gadget_resume(dwc); break; case DWC3_GCTL_PRTCAP_HOST: @@ -2068,7 +2091,7 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) ret = dwc3_core_init_for_resume(dwc); if (ret) return ret; - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST, true); break; } /* Restore GUSB2PHYCFG bits that were modified in suspend */ @@ -2093,7 +2116,7 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) if (ret) return ret; - dwc3_set_prtcap(dwc, dwc->current_dr_role); + dwc3_set_prtcap(dwc, dwc->current_dr_role, true); dwc3_otg_init(dwc); if (dwc->current_otg_role == DWC3_OTG_ROLE_HOST) { diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index 85b538674692..4041cf926e0e 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -1512,7 +1512,7 @@ struct dwc3_gadget_ep_cmd_params { #define DWC3_HAS_OTG BIT(3) /* prototypes */ -void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode); +void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode, bool ignore_susphy); void dwc3_set_mode(struct dwc3 *dwc, u32 mode); u32 dwc3_core_fifo_space(struct dwc3_ep *dep, u8 type); diff --git a/drivers/usb/dwc3/drd.c b/drivers/usb/dwc3/drd.c index 2462e4c7530e..b16eced93ddb 100644 --- a/drivers/usb/dwc3/drd.c +++ b/drivers/usb/dwc3/drd.c @@ -174,7 +174,7 @@ void dwc3_otg_init(struct dwc3 *dwc) * block "Initialize GCTL for OTG operation". */ /* GCTL.PrtCapDir=2'b11 */ - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG, true); /* GUSB2PHYCFG0.SusPHY=0 */ reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); reg &= ~DWC3_GUSB2PHYCFG_SUSPHY; @@ -607,7 +607,7 @@ int dwc3_drd_init(struct dwc3 *dwc) dwc3_drd_update(dwc); } else { - dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG); + dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_OTG, true); /* use OTG block to get ID event */ irq = dwc3_otg_get_irq(dwc); diff --git a/drivers/usb/dwc3/dwc3-pci.c b/drivers/usb/dwc3/dwc3-pci.c index 1872de3ce98b..5e0b326875fa 100644 --- a/drivers/usb/dwc3/dwc3-pci.c +++ b/drivers/usb/dwc3/dwc3-pci.c @@ -132,11 +132,21 @@ static const struct property_entry dwc3_pci_intel_byt_properties[] = { {} }; +/* + * Intel Merrifield SoC uses these endpoints for tracing and they cannot + * be re-allocated if being used because the side band flow control signals + * are hard wired to certain endpoints: + * - 1 High BW Bulk IN (IN#1) (RTIT) + * - 1 1KB BW Bulk IN (IN#8) + 1 1KB BW Bulk OUT (Run Control) (OUT#8) + */ +static const u8 dwc3_pci_mrfld_reserved_endpoints[] = { 3, 16, 17 }; + static const struct property_entry dwc3_pci_mrfld_properties[] = { PROPERTY_ENTRY_STRING("dr_mode", "otg"), PROPERTY_ENTRY_STRING("linux,extcon-name", "mrfld_bcove_pwrsrc"), PROPERTY_ENTRY_BOOL("snps,dis_u3_susphy_quirk"), PROPERTY_ENTRY_BOOL("snps,dis_u2_susphy_quirk"), + PROPERTY_ENTRY_U8_ARRAY("snps,reserved-endpoints", dwc3_pci_mrfld_reserved_endpoints), PROPERTY_ENTRY_BOOL("snps,usb2-gadget-lpm-disable"), PROPERTY_ENTRY_BOOL("linux,sysdev_is_parent"), {} diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index d1ec6b359916..e7def7940a9d 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -2457,11 +2457,39 @@ static void __dwc3_gadget_set_speed(struct dwc3 *dwc) static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on) { u32 reg; - u32 timeout = 500; + u32 timeout = 2000; + u32 saved_config = 0; if (pm_runtime_suspended(dwc->dev)) return 0; + /* + * When operating in USB 2.0 speeds (HS/FS), ensure that + * GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting + * or stopping the controller. This resolves timeout issues that occur + * during frequent role switches between host and device modes. + * + * Save and clear these settings, then restore them after completing the + * controller start or stop sequence. + * + * This solution was discovered through experimentation as it is not + * mentioned in the dwc3 programming guide. It has been tested on an + * Exynos platforms. + */ + reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); + if (reg & DWC3_GUSB2PHYCFG_SUSPHY) { + saved_config |= DWC3_GUSB2PHYCFG_SUSPHY; + reg &= ~DWC3_GUSB2PHYCFG_SUSPHY; + } + + if (reg & DWC3_GUSB2PHYCFG_ENBLSLPM) { + saved_config |= DWC3_GUSB2PHYCFG_ENBLSLPM; + reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM; + } + + if (saved_config) + dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); + reg = dwc3_readl(dwc->regs, DWC3_DCTL); if (is_on) { if (DWC3_VER_IS_WITHIN(DWC3, ANY, 187A)) { @@ -2484,10 +2512,17 @@ static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on) dwc3_gadget_dctl_write_safe(dwc, reg); do { + usleep_range(1000, 2000); reg = dwc3_readl(dwc->regs, DWC3_DSTS); reg &= DWC3_DSTS_DEVCTRLHLT; } while (--timeout && !(!is_on ^ !reg)); + if (saved_config) { + reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); + reg |= saved_config; + dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); + } + if (!timeout) return -ETIMEDOUT; @@ -4262,14 +4297,18 @@ static irqreturn_t dwc3_process_event_buf(struct dwc3_event_buffer *evt) reg &= ~DWC3_GEVNTSIZ_INTMASK; dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), reg); + evt->flags &= ~DWC3_EVENT_PENDING; + /* + * Add an explicit write memory barrier to make sure that the update of + * clearing DWC3_EVENT_PENDING is observed in dwc3_check_event_buf() + */ + wmb(); + if (dwc->imod_interval) { dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), DWC3_GEVNTCOUNT_EHB); dwc3_writel(dwc->regs, DWC3_DEV_IMOD(0), dwc->imod_interval); } - /* Keep the clearing of DWC3_EVENT_PENDING at the end */ - evt->flags &= ~DWC3_EVENT_PENDING; - return ret; } @@ -4322,6 +4361,12 @@ static irqreturn_t dwc3_check_event_buf(struct dwc3_event_buffer *evt) if (!count) return IRQ_NONE; + if (count > evt->length) { + dev_err_ratelimited(dwc->dev, "invalid count(%u) > evt->length(%u)\n", + count, evt->length); + return IRQ_NONE; + } + evt->count = count; evt->flags |= DWC3_EVENT_PENDING; diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c index 94e86c385760..96a955e16e25 100644 --- a/drivers/usb/gadget/composite.c +++ b/drivers/usb/gadget/composite.c @@ -1004,10 +1004,11 @@ static int set_config(struct usb_composite_dev *cdev, else usb_gadget_set_remote_wakeup(gadget, 0); done: - if (power <= USB_SELF_POWER_VBUS_MAX_DRAW) - usb_gadget_set_selfpowered(gadget); - else + if (power > USB_SELF_POWER_VBUS_MAX_DRAW || + (c && !(c->bmAttributes & USB_CONFIG_ATT_SELFPOWER))) usb_gadget_clear_selfpowered(gadget); + else + usb_gadget_set_selfpowered(gadget); usb_gadget_vbus_draw(gadget, power); if (result >= 0 && cdev->delayed_status) @@ -2475,7 +2476,10 @@ void composite_suspend(struct usb_gadget *gadget) cdev->suspended = 1; - usb_gadget_set_selfpowered(gadget); + if (cdev->config && + cdev->config->bmAttributes & USB_CONFIG_ATT_SELFPOWER) + usb_gadget_set_selfpowered(gadget); + usb_gadget_vbus_draw(gadget, 2); } @@ -2504,8 +2508,11 @@ void composite_resume(struct usb_gadget *gadget) else maxpower = min(maxpower, 900U); - if (maxpower > USB_SELF_POWER_VBUS_MAX_DRAW) + if (maxpower > USB_SELF_POWER_VBUS_MAX_DRAW || + !(cdev->config->bmAttributes & USB_CONFIG_ATT_SELFPOWER)) usb_gadget_clear_selfpowered(gadget); + else + usb_gadget_set_selfpowered(gadget); usb_gadget_vbus_draw(gadget, maxpower); } diff --git a/drivers/usb/gadget/function/f_midi.c b/drivers/usb/gadget/function/f_midi.c index 71a1a26e85c7..3e8ea1bbe429 100644 --- a/drivers/usb/gadget/function/f_midi.c +++ b/drivers/usb/gadget/function/f_midi.c @@ -282,7 +282,7 @@ f_midi_complete(struct usb_ep *ep, struct usb_request *req) /* Our transmit completed. See if there's more to go. * f_midi_transmit eats req, don't queue it again. */ req->length = 0; - f_midi_transmit(midi); + queue_work(system_highpri_wq, &midi->work); return; } break; @@ -999,11 +999,11 @@ static int f_midi_bind(struct usb_configuration *c, struct usb_function *f) } /* configure the endpoint descriptors ... */ - ms_out_desc.bLength = USB_DT_MS_ENDPOINT_SIZE(midi->in_ports); - ms_out_desc.bNumEmbMIDIJack = midi->in_ports; + ms_out_desc.bLength = USB_DT_MS_ENDPOINT_SIZE(midi->out_ports); + ms_out_desc.bNumEmbMIDIJack = midi->out_ports; - ms_in_desc.bLength = USB_DT_MS_ENDPOINT_SIZE(midi->out_ports); - ms_in_desc.bNumEmbMIDIJack = midi->out_ports; + ms_in_desc.bLength = USB_DT_MS_ENDPOINT_SIZE(midi->in_ports); + ms_in_desc.bNumEmbMIDIJack = midi->in_ports; /* ... and add them to the list */ endpoint_descriptor_index = i; diff --git a/drivers/usb/gadget/function/f_tcm.c b/drivers/usb/gadget/function/f_tcm.c index de161ee0b1f9..934e4b2a049f 100644 --- a/drivers/usb/gadget/function/f_tcm.c +++ b/drivers/usb/gadget/function/f_tcm.c @@ -245,7 +245,6 @@ static int bot_send_write_request(struct usbg_cmd *cmd) { struct f_uas *fu = cmd->fu; struct se_cmd *se_cmd = &cmd->se_cmd; - struct usb_gadget *gadget = fuas_to_gadget(fu); int ret; init_completion(&cmd->write_complete); @@ -256,22 +255,6 @@ static int bot_send_write_request(struct usbg_cmd *cmd) return -EINVAL; } - if (!gadget->sg_supported) { - cmd->data_buf = kmalloc(se_cmd->data_length, GFP_KERNEL); - if (!cmd->data_buf) - return -ENOMEM; - - fu->bot_req_out->buf = cmd->data_buf; - } else { - fu->bot_req_out->buf = NULL; - fu->bot_req_out->num_sgs = se_cmd->t_data_nents; - fu->bot_req_out->sg = se_cmd->t_data_sg; - } - - fu->bot_req_out->complete = usbg_data_write_cmpl; - fu->bot_req_out->length = se_cmd->data_length; - fu->bot_req_out->context = cmd; - ret = usbg_prepare_w_request(cmd, fu->bot_req_out); if (ret) goto cleanup; @@ -973,6 +956,7 @@ static void usbg_data_write_cmpl(struct usb_ep *ep, struct usb_request *req) return; cleanup: + target_put_sess_cmd(se_cmd); transport_generic_free_cmd(&cmd->se_cmd, 0); } @@ -1065,8 +1049,7 @@ static void usbg_cmd_work(struct work_struct *work) out: transport_send_check_condition_and_sense(se_cmd, - TCM_UNSUPPORTED_SCSI_OPCODE, 1); - transport_generic_free_cmd(&cmd->se_cmd, 0); + TCM_UNSUPPORTED_SCSI_OPCODE, 0); } static struct usbg_cmd *usbg_get_cmd(struct f_uas *fu, @@ -1194,8 +1177,7 @@ static void bot_cmd_work(struct work_struct *work) out: transport_send_check_condition_and_sense(se_cmd, - TCM_UNSUPPORTED_SCSI_OPCODE, 1); - transport_generic_free_cmd(&cmd->se_cmd, 0); + TCM_UNSUPPORTED_SCSI_OPCODE, 0); } static int bot_submit_command(struct f_uas *fu, @@ -2018,43 +2000,39 @@ static int tcm_bind(struct usb_configuration *c, struct usb_function *f) bot_intf_desc.bInterfaceNumber = iface; uasp_intf_desc.bInterfaceNumber = iface; fu->iface = iface; - ep = usb_ep_autoconfig_ss(gadget, &uasp_ss_bi_desc, - &uasp_bi_ep_comp_desc); + ep = usb_ep_autoconfig(gadget, &uasp_fs_bi_desc); if (!ep) goto ep_fail; fu->ep_in = ep; - ep = usb_ep_autoconfig_ss(gadget, &uasp_ss_bo_desc, - &uasp_bo_ep_comp_desc); + ep = usb_ep_autoconfig(gadget, &uasp_fs_bo_desc); if (!ep) goto ep_fail; fu->ep_out = ep; - ep = usb_ep_autoconfig_ss(gadget, &uasp_ss_status_desc, - &uasp_status_in_ep_comp_desc); + ep = usb_ep_autoconfig(gadget, &uasp_fs_status_desc); if (!ep) goto ep_fail; fu->ep_status = ep; - ep = usb_ep_autoconfig_ss(gadget, &uasp_ss_cmd_desc, - &uasp_cmd_comp_desc); + ep = usb_ep_autoconfig(gadget, &uasp_fs_cmd_desc); if (!ep) goto ep_fail; fu->ep_cmd = ep; /* Assume endpoint addresses are the same for both speeds */ - uasp_bi_desc.bEndpointAddress = uasp_ss_bi_desc.bEndpointAddress; - uasp_bo_desc.bEndpointAddress = uasp_ss_bo_desc.bEndpointAddress; + uasp_bi_desc.bEndpointAddress = uasp_fs_bi_desc.bEndpointAddress; + uasp_bo_desc.bEndpointAddress = uasp_fs_bo_desc.bEndpointAddress; uasp_status_desc.bEndpointAddress = - uasp_ss_status_desc.bEndpointAddress; - uasp_cmd_desc.bEndpointAddress = uasp_ss_cmd_desc.bEndpointAddress; + uasp_fs_status_desc.bEndpointAddress; + uasp_cmd_desc.bEndpointAddress = uasp_fs_cmd_desc.bEndpointAddress; - uasp_fs_bi_desc.bEndpointAddress = uasp_ss_bi_desc.bEndpointAddress; - uasp_fs_bo_desc.bEndpointAddress = uasp_ss_bo_desc.bEndpointAddress; - uasp_fs_status_desc.bEndpointAddress = - uasp_ss_status_desc.bEndpointAddress; - uasp_fs_cmd_desc.bEndpointAddress = uasp_ss_cmd_desc.bEndpointAddress; + uasp_ss_bi_desc.bEndpointAddress = uasp_fs_bi_desc.bEndpointAddress; + uasp_ss_bo_desc.bEndpointAddress = uasp_fs_bo_desc.bEndpointAddress; + uasp_ss_status_desc.bEndpointAddress = + uasp_fs_status_desc.bEndpointAddress; + uasp_ss_cmd_desc.bEndpointAddress = uasp_fs_cmd_desc.bEndpointAddress; ret = usb_assign_descriptors(f, uasp_fs_function_desc, uasp_hs_function_desc, uasp_ss_function_desc, @@ -2098,9 +2076,14 @@ static void tcm_delayed_set_alt(struct work_struct *wq) static int tcm_get_alt(struct usb_function *f, unsigned intf) { - if (intf == bot_intf_desc.bInterfaceNumber) + struct f_uas *fu = to_f_uas(f); + + if (fu->iface != intf) + return -EOPNOTSUPP; + + if (fu->flags & USBG_IS_BOT) return USB_G_ALT_INT_BBB; - if (intf == uasp_intf_desc.bInterfaceNumber) + else if (fu->flags & USBG_IS_UAS) return USB_G_ALT_INT_UAS; return -EOPNOTSUPP; @@ -2110,6 +2093,9 @@ static int tcm_set_alt(struct usb_function *f, unsigned intf, unsigned alt) { struct f_uas *fu = to_f_uas(f); + if (fu->iface != intf) + return -EOPNOTSUPP; + if ((alt == USB_G_ALT_INT_BBB) || (alt == USB_G_ALT_INT_UAS)) { struct guas_setup_wq *work; diff --git a/drivers/usb/gadget/function/u_serial.c b/drivers/usb/gadget/function/u_serial.c index 8481b8807494..37ba396d5473 100644 --- a/drivers/usb/gadget/function/u_serial.c +++ b/drivers/usb/gadget/function/u_serial.c @@ -1393,10 +1393,6 @@ void gserial_disconnect(struct gserial *gser) /* REVISIT as above: how best to track this? */ port->port_line_coding = gser->port_line_coding; - /* disable endpoints, aborting down any active I/O */ - usb_ep_disable(gser->out); - usb_ep_disable(gser->in); - port->port_usb = NULL; gser->ioport = NULL; if (port->port.count > 0) { @@ -1408,6 +1404,10 @@ void gserial_disconnect(struct gserial *gser) spin_unlock(&port->port_lock); spin_unlock_irqrestore(&serial_port_lock, flags); + /* disable endpoints, aborting down any active I/O */ + usb_ep_disable(gser->out); + usb_ep_disable(gser->in); + /* finally, free any unused/unusable I/O buffers */ spin_lock_irqsave(&port->port_lock, flags); if (port->port.count == 0) diff --git a/drivers/usb/gadget/udc/aspeed-vhub/dev.c b/drivers/usb/gadget/udc/aspeed-vhub/dev.c index d918e8b2af3c..c5f712383775 100644 --- a/drivers/usb/gadget/udc/aspeed-vhub/dev.c +++ b/drivers/usb/gadget/udc/aspeed-vhub/dev.c @@ -538,6 +538,9 @@ int ast_vhub_init_dev(struct ast_vhub *vhub, unsigned int idx) d->vhub = vhub; d->index = idx; d->name = devm_kasprintf(parent, GFP_KERNEL, "port%d", idx+1); + if (!d->name) + return -ENOMEM; + d->regs = vhub->regs + 0x100 + 0x10 * idx; ast_vhub_init_ep0(vhub, &d->ep0, d); diff --git a/drivers/usb/gadget/udc/renesas_usb3.c b/drivers/usb/gadget/udc/renesas_usb3.c index a10f41c4a3f2..d888741d3e2f 100644 --- a/drivers/usb/gadget/udc/renesas_usb3.c +++ b/drivers/usb/gadget/udc/renesas_usb3.c @@ -306,7 +306,7 @@ struct renesas_usb3_request { struct list_head queue; }; -#define USB3_EP_NAME_SIZE 8 +#define USB3_EP_NAME_SIZE 16 struct renesas_usb3_ep { struct usb_ep ep; struct renesas_usb3 *usb3; diff --git a/drivers/usb/gadget/udc/tegra-xudc.c b/drivers/usb/gadget/udc/tegra-xudc.c index fdbb9d73aa8e..13a2f5276072 100644 --- a/drivers/usb/gadget/udc/tegra-xudc.c +++ b/drivers/usb/gadget/udc/tegra-xudc.c @@ -1737,6 +1737,10 @@ static int __tegra_xudc_ep_disable(struct tegra_xudc_ep *ep) val = xudc_readl(xudc, CTRL); val &= ~CTRL_RUN; xudc_writel(xudc, val, CTRL); + + val = xudc_readl(xudc, ST); + if (val & ST_RC) + xudc_writel(xudc, ST_RC, ST); } dev_info(xudc->dev, "ep %u disabled\n", ep->index); diff --git a/drivers/usb/host/max3421-hcd.c b/drivers/usb/host/max3421-hcd.c index 6d95b90683bc..37a5914f7987 100644 --- a/drivers/usb/host/max3421-hcd.c +++ b/drivers/usb/host/max3421-hcd.c @@ -1956,6 +1956,12 @@ max3421_remove(struct spi_device *spi) return 0; } +static const struct spi_device_id max3421_spi_ids[] = { + { "max3421" }, + { }, +}; +MODULE_DEVICE_TABLE(spi, max3421_spi_ids); + static const struct of_device_id max3421_of_match_table[] = { { .compatible = "maxim,max3421", }, {}, @@ -1965,6 +1971,7 @@ MODULE_DEVICE_TABLE(of, max3421_of_match_table); static struct spi_driver max3421_driver = { .probe = max3421_probe, .remove = max3421_remove, + .id_table = max3421_spi_ids, .driver = { .name = "max3421-hcd", .of_match_table = of_match_ptr(max3421_of_match_table), diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c index 41efe927d8f3..70153ce60128 100644 --- a/drivers/usb/host/ohci-pci.c +++ b/drivers/usb/host/ohci-pci.c @@ -165,6 +165,25 @@ static int ohci_quirk_amd700(struct usb_hcd *hcd) return 0; } +static int ohci_quirk_loongson(struct usb_hcd *hcd) +{ + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); + + /* + * Loongson's LS7A OHCI controller (rev 0x02) has a + * flaw. MMIO register with offset 0x60/64 is treated + * as legacy PS2-compatible keyboard/mouse interface. + * Since OHCI only use 4KB BAR resource, LS7A OHCI's + * 32KB BAR is wrapped around (the 2nd 4KB BAR space + * is the same as the 1st 4KB internally). So add 4KB + * offset (0x1000) to the OHCI registers as a quirk. + */ + if (pdev->revision == 0x2) + hcd->regs += SZ_4K; /* SZ_4K = 0x1000 */ + + return 0; +} + static int ohci_quirk_qemu(struct usb_hcd *hcd) { struct ohci_hcd *ohci = hcd_to_ohci(hcd); @@ -225,6 +244,10 @@ static const struct pci_device_id ohci_pci_quirks[] = { .driver_data = (unsigned long)ohci_quirk_amd700, }, { + PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a24), + .driver_data = (unsigned long)ohci_quirk_loongson, + }, + { .vendor = PCI_VENDOR_ID_APPLE, .device = 0x003f, .subvendor = PCI_SUBVENDOR_ID_REDHAT_QUMRANET, diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c index ef08d68b9714..04336c1d8dcb 100644 --- a/drivers/usb/host/pci-quirks.c +++ b/drivers/usb/host/pci-quirks.c @@ -948,6 +948,15 @@ static void quirk_usb_disable_ehci(struct pci_dev *pdev) * booting from USB disk or using a usb keyboard */ hcc_params = readl(base + EHCI_HCC_PARAMS); + + /* LS7A EHCI controller doesn't have extended capabilities, the + * EECP (EHCI Extended Capabilities Pointer) field of HCCPARAMS + * register should be 0x0 but it reads as 0xa0. So clear it to + * avoid error messages on boot. + */ + if (pdev->vendor == PCI_VENDOR_ID_LOONGSON && pdev->device == 0x7a14) + hcc_params &= ~(0xffL << 8); + offset = (hcc_params >> 8) & 0xff; while (offset && --count) { pci_read_config_dword(pdev, offset, &cap); diff --git a/drivers/usb/host/uhci-platform.c b/drivers/usb/host/uhci-platform.c index be9e9db7cad1..c0834bac4c95 100644 --- a/drivers/usb/host/uhci-platform.c +++ b/drivers/usb/host/uhci-platform.c @@ -122,7 +122,7 @@ static int uhci_hcd_platform_probe(struct platform_device *pdev) } /* Get and enable clock if any specified */ - uhci->clk = devm_clk_get(&pdev->dev, NULL); + uhci->clk = devm_clk_get_optional(&pdev->dev, NULL); if (IS_ERR(uhci->clk)) { ret = PTR_ERR(uhci->clk); goto err_rmr; diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index c44b66628a6d..db22ab0d8889 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1761,6 +1761,8 @@ struct xhci_command *xhci_alloc_command(struct xhci_hcd *xhci, } command->status = 0; + /* set default timeout to 5000 ms */ + command->timeout_ms = XHCI_CMD_DEFAULT_TIMEOUT; INIT_LIST_HEAD(&command->cmd_list); return command; } @@ -2404,7 +2406,8 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) * and our use of dma addresses in the trb_address_map radix tree needs * TRB_SEGMENT_SIZE alignment, so we pick the greater alignment need. */ - if (xhci->quirks & XHCI_ZHAOXIN_TRB_FETCH) + if (xhci->quirks & XHCI_TRB_OVERFETCH) + /* Buggy HC prefetches beyond segment bounds - allocate dummy space at the end */ xhci->segment_pool = dma_pool_create("xHCI ring segments", dev, TRB_SEGMENT_SIZE * 2, TRB_SEGMENT_SIZE * 2, xhci->page_size * 2); else diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 48a1cf5d9a1f..18200d3662fe 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -28,8 +28,8 @@ #define SPARSE_CNTL_ENABLE 0xC12C /* Device for a quirk */ -#define PCI_VENDOR_ID_FRESCO_LOGIC 0x1b73 -#define PCI_DEVICE_ID_FRESCO_LOGIC_PDK 0x1000 +#define PCI_VENDOR_ID_FRESCO_LOGIC 0x1b73 +#define PCI_DEVICE_ID_FRESCO_LOGIC_PDK 0x1000 #define PCI_DEVICE_ID_FRESCO_LOGIC_FL1009 0x1009 #define PCI_DEVICE_ID_FRESCO_LOGIC_FL1100 0x1100 #define PCI_DEVICE_ID_FRESCO_LOGIC_FL1400 0x1400 @@ -38,8 +38,10 @@ #define PCI_DEVICE_ID_EJ168 0x7023 #define PCI_DEVICE_ID_EJ188 0x7052 -#define PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI 0x8c31 -#define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI 0x9c31 +#define PCI_DEVICE_ID_VIA_VL805 0x3483 + +#define PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI 0x8c31 +#define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI 0x9c31 #define PCI_DEVICE_ID_INTEL_WILDCATPOINT_LP_XHCI 0x9cb1 #define PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI 0x22b5 #define PCI_DEVICE_ID_INTEL_SUNRISEPOINT_H_XHCI 0xa12f @@ -305,8 +307,10 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) pdev->device == 0x3432) xhci->quirks |= XHCI_BROKEN_STREAMS; - if (pdev->vendor == PCI_VENDOR_ID_VIA && pdev->device == 0x3483) + if (pdev->vendor == PCI_VENDOR_ID_VIA && pdev->device == PCI_DEVICE_ID_VIA_VL805) { xhci->quirks |= XHCI_LPM_SUPPORT; + xhci->quirks |= XHCI_TRB_OVERFETCH; + } if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA && pdev->device == PCI_DEVICE_ID_ASMEDIA_1042_XHCI) { @@ -354,11 +358,11 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) if (pdev->device == 0x9202) { xhci->quirks |= XHCI_RESET_ON_RESUME; - xhci->quirks |= XHCI_ZHAOXIN_TRB_FETCH; + xhci->quirks |= XHCI_TRB_OVERFETCH; } if (pdev->device == 0x9203) - xhci->quirks |= XHCI_ZHAOXIN_TRB_FETCH; + xhci->quirks |= XHCI_TRB_OVERFETCH; } if (pdev->vendor == PCI_DEVICE_ID_CADENCE && diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index dd35deb713ab..18ac4f48b5cd 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -333,9 +333,10 @@ void xhci_ring_cmd_db(struct xhci_hcd *xhci) readl(&xhci->dba->doorbell[0]); } -static bool xhci_mod_cmd_timer(struct xhci_hcd *xhci, unsigned long delay) +static bool xhci_mod_cmd_timer(struct xhci_hcd *xhci) { - return mod_delayed_work(system_wq, &xhci->cmd_timer, delay); + return mod_delayed_work(system_wq, &xhci->cmd_timer, + msecs_to_jiffies(xhci->current_cmd->timeout_ms)); } static struct xhci_command *xhci_next_queued_cmd(struct xhci_hcd *xhci) @@ -379,7 +380,8 @@ static void xhci_handle_stopped_cmd_ring(struct xhci_hcd *xhci, if ((xhci->cmd_ring->dequeue != xhci->cmd_ring->enqueue) && !(xhci->xhc_state & XHCI_STATE_DYING)) { xhci->current_cmd = cur_cmd; - xhci_mod_cmd_timer(xhci, XHCI_CMD_DEFAULT_TIMEOUT); + if (cur_cmd) + xhci_mod_cmd_timer(xhci); xhci_ring_cmd_db(xhci); } } @@ -1181,16 +1183,19 @@ static void xhci_handle_cmd_stop_ep(struct xhci_hcd *xhci, int slot_id, * Stopped state, but it will soon change to Running. * * Assume this bug on unexpected Stop Endpoint failures. - * Keep retrying until the EP starts and stops again, on - * chips where this is known to help. Wait for 100ms. + * Keep retrying until the EP starts and stops again. */ - if (time_is_before_jiffies(ep->stop_time + msecs_to_jiffies(100))) - break; fallthrough; case EP_STATE_RUNNING: /* Race, HW handled stop ep cmd before ep was running */ xhci_dbg(xhci, "Stop ep completion ctx error, ctx_state %d\n", GET_EP_CTX_STATE(ep_ctx)); + /* + * Don't retry forever if we guessed wrong or a defective HC never starts + * the EP or says 'Running' but fails the command. We must give back TDs. + */ + if (time_is_before_jiffies(ep->stop_time + msecs_to_jiffies(100))) + break; command = xhci_alloc_command(xhci, false, GFP_ATOMIC); if (!command) @@ -1922,7 +1927,7 @@ static void handle_cmd_completion(struct xhci_hcd *xhci, if (!list_is_singular(&xhci->cmd_list)) { xhci->current_cmd = list_first_entry(&cmd->cmd_list, struct xhci_command, cmd_list); - xhci_mod_cmd_timer(xhci, XHCI_CMD_DEFAULT_TIMEOUT); + xhci_mod_cmd_timer(xhci); } else if (xhci->current_cmd == cmd) { xhci->current_cmd = NULL; } @@ -4623,7 +4628,7 @@ static int queue_command(struct xhci_hcd *xhci, struct xhci_command *cmd, /* if there are no other commands queued we start the timeout timer */ if (list_empty(&xhci->cmd_list)) { xhci->current_cmd = cmd; - xhci_mod_cmd_timer(xhci, XHCI_CMD_DEFAULT_TIMEOUT); + xhci_mod_cmd_timer(xhci); } list_add_tail(&cmd->cmd_list, &xhci->cmd_list); diff --git a/drivers/usb/host/xhci-tegra.c b/drivers/usb/host/xhci-tegra.c index 51eabc5e8770..14a772feab79 100644 --- a/drivers/usb/host/xhci-tegra.c +++ b/drivers/usb/host/xhci-tegra.c @@ -1228,6 +1228,7 @@ static void tegra_xhci_id_work(struct work_struct *work) tegra->otg_usb3_port = tegra_xusb_padctl_get_usb3_companion(tegra->padctl, tegra->otg_usb2_port); + pm_runtime_get_sync(tegra->dev); if (tegra->host_mode) { /* switch to host mode */ if (tegra->otg_usb3_port >= 0) { @@ -1257,6 +1258,7 @@ static void tegra_xhci_id_work(struct work_struct *work) } tegra_xhci_set_port_power(tegra, true, true); + pm_runtime_mark_last_busy(tegra->dev); } else { if (tegra->otg_usb3_port >= 0) @@ -1264,6 +1266,7 @@ static void tegra_xhci_id_work(struct work_struct *work) tegra_xhci_set_port_power(tegra, true, false); } + pm_runtime_put_autosuspend(tegra->dev); } #if IS_ENABLED(CONFIG_PM) || IS_ENABLED(CONFIG_PM_SLEEP) diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 60bb086f1394..8f7f0876aa4d 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -4190,12 +4190,18 @@ disable_slot: return 0; } -/* - * Issue an Address Device command and optionally send a corresponding - * SetAddress request to the device. +/** + * xhci_setup_device - issues an Address Device command to assign a unique + * USB bus address. + * @hcd: USB host controller data structure. + * @udev: USB dev structure representing the connected device. + * @setup: Enum specifying setup mode: address only or with context. + * @timeout_ms: Max wait time (ms) for the command operation to complete. + * + * Return: 0 if successful; otherwise, negative error code. */ static int xhci_setup_device(struct usb_hcd *hcd, struct usb_device *udev, - enum xhci_setup_dev setup) + enum xhci_setup_dev setup, unsigned int timeout_ms) { const char *act = setup == SETUP_CONTEXT_ONLY ? "context" : "address"; unsigned long flags; @@ -4252,6 +4258,7 @@ static int xhci_setup_device(struct usb_hcd *hcd, struct usb_device *udev, } command->in_ctx = virt_dev->in_ctx; + command->timeout_ms = timeout_ms; slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx); ctrl_ctx = xhci_get_input_control_ctx(virt_dev->in_ctx); @@ -4380,14 +4387,16 @@ out: return ret; } -static int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) +static int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev, + unsigned int timeout_ms) { - return xhci_setup_device(hcd, udev, SETUP_CONTEXT_ADDRESS); + return xhci_setup_device(hcd, udev, SETUP_CONTEXT_ADDRESS, timeout_ms); } static int xhci_enable_device(struct usb_hcd *hcd, struct usb_device *udev) { - return xhci_setup_device(hcd, udev, SETUP_CONTEXT_ONLY); + return xhci_setup_device(hcd, udev, SETUP_CONTEXT_ONLY, + XHCI_CMD_DEFAULT_TIMEOUT); } /* diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 564a34949265..5a0b59c35003 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -563,6 +563,8 @@ struct xhci_command { struct completion *completion; union xhci_trb *command_trb; struct list_head cmd_list; + /* xHCI command response timeout in milliseconds */ + unsigned int timeout_ms; }; /* drop context bitmasks */ @@ -1326,8 +1328,11 @@ struct xhci_td { unsigned int num_trbs; }; -/* xHCI command default timeout value */ -#define XHCI_CMD_DEFAULT_TIMEOUT (5 * HZ) +/* + * xHCI command default timeout value in milliseconds. + * USB 3.2 spec, section 9.2.6.1 + */ +#define XHCI_CMD_DEFAULT_TIMEOUT 5000 /* command descriptor */ struct xhci_cd { @@ -1661,7 +1666,7 @@ struct xhci_hcd { #define XHCI_CDNS_HOST BIT_ULL(43) #define XHCI_SUSPEND_RESUME_CLKS BIT_ULL(43) #define XHCI_RESET_TO_DEFAULT BIT_ULL(44) -#define XHCI_ZHAOXIN_TRB_FETCH BIT_ULL(45) +#define XHCI_TRB_OVERFETCH BIT_ULL(45) #define XHCI_ZHAOXIN_HOST BIT_ULL(46) #define XHCI_WRITE_64_HI_LO BIT_ULL(47) #define XHCI_CDNS_SCTX_QUIRK BIT_ULL(48) diff --git a/drivers/usb/renesas_usbhs/common.c b/drivers/usb/renesas_usbhs/common.c index 3af91b2b8f76..df679908b8d2 100644 --- a/drivers/usb/renesas_usbhs/common.c +++ b/drivers/usb/renesas_usbhs/common.c @@ -312,8 +312,10 @@ static int usbhsc_clk_get(struct device *dev, struct usbhs_priv *priv) priv->clks[1] = of_clk_get(dev_of_node(dev), 1); if (PTR_ERR(priv->clks[1]) == -ENOENT) priv->clks[1] = NULL; - else if (IS_ERR(priv->clks[1])) + else if (IS_ERR(priv->clks[1])) { + clk_put(priv->clks[0]); return PTR_ERR(priv->clks[1]); + } return 0; } @@ -772,6 +774,8 @@ static int usbhs_remove(struct platform_device *pdev) dev_dbg(&pdev->dev, "usb remove\n"); + flush_delayed_work(&priv->notify_hotplug_work); + /* power off */ if (!usbhs_get_dparam(priv, runtime_pwctrl)) usbhsc_power_ctrl(priv, 0); diff --git a/drivers/usb/renesas_usbhs/mod_gadget.c b/drivers/usb/renesas_usbhs/mod_gadget.c index 105132ae87ac..e8e5723f5412 100644 --- a/drivers/usb/renesas_usbhs/mod_gadget.c +++ b/drivers/usb/renesas_usbhs/mod_gadget.c @@ -1094,7 +1094,7 @@ int usbhs_mod_gadget_probe(struct usbhs_priv *priv) goto usbhs_mod_gadget_probe_err_gpriv; } - gpriv->transceiver = usb_get_phy(USB_PHY_TYPE_UNDEFINED); + gpriv->transceiver = devm_usb_get_phy(dev, USB_PHY_TYPE_UNDEFINED); dev_info(dev, "%stransceiver found\n", !IS_ERR(gpriv->transceiver) ? "" : "no "); diff --git a/drivers/usb/roles/class.c b/drivers/usb/roles/class.c index a327f8bc5704..917dffe9aee5 100644 --- a/drivers/usb/roles/class.c +++ b/drivers/usb/roles/class.c @@ -354,14 +354,15 @@ usb_role_switch_register(struct device *parent, dev_set_name(&sw->dev, "%s-role-switch", desc->name ? desc->name : dev_name(parent)); + sw->registered = true; + ret = device_register(&sw->dev); if (ret) { + sw->registered = false; put_device(&sw->dev); return ERR_PTR(ret); } - sw->registered = true; - /* TODO: Symlinks for the host port and the device controller. */ return sw; diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 1915b92c388f..a40d5e625015 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -1057,6 +1057,22 @@ static const struct usb_device_id id_table_combined[] = { .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, /* GMC devices */ { USB_DEVICE(GMC_VID, GMC_Z216C_PID) }, + /* Altera USB Blaster 3 */ + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_6022_PID, 1) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_6025_PID, 2) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_6026_PID, 2) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_6026_PID, 3) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_6029_PID, 2) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602A_PID, 2) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602A_PID, 3) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602C_PID, 1) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602D_PID, 1) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602D_PID, 2) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602E_PID, 1) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602E_PID, 2) }, + { USB_DEVICE_INTERFACE_NUMBER(ALTERA_VID, ALTERA_UB3_602E_PID, 3) }, + /* Abacus Electrics */ + { USB_DEVICE(FTDI_VID, ABACUS_OPTICAL_PROBE_PID) }, { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index b2aec1106678..9c95ca876bae 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -436,6 +436,11 @@ #define LINX_FUTURE_2_PID 0xF44C /* Linx future device */ /* + * Abacus Electrics + */ +#define ABACUS_OPTICAL_PROBE_PID 0xf458 /* ABACUS ELECTRICS Optical Probe */ + +/* * Oceanic product ids */ #define FTDI_OCEANIC_PID 0xF460 /* Oceanic dive instrument */ @@ -1605,3 +1610,16 @@ */ #define GMC_VID 0x1cd7 #define GMC_Z216C_PID 0x0217 /* GMC Z216C Adapter IR-USB */ + +/* + * Altera USB Blaster 3 (http://www.altera.com). + */ +#define ALTERA_VID 0x09fb +#define ALTERA_UB3_6022_PID 0x6022 +#define ALTERA_UB3_6025_PID 0x6025 +#define ALTERA_UB3_6026_PID 0x6026 +#define ALTERA_UB3_6029_PID 0x6029 +#define ALTERA_UB3_602A_PID 0x602a +#define ALTERA_UB3_602C_PID 0x602c +#define ALTERA_UB3_602D_PID 0x602d +#define ALTERA_UB3_602E_PID 0x602e diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 89e6a9afb808..b09d95da2fe5 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -611,6 +611,7 @@ static void option_instat_callback(struct urb *urb); /* Sierra Wireless products */ #define SIERRA_VENDOR_ID 0x1199 #define SIERRA_PRODUCT_EM9191 0x90d3 +#define SIERRA_PRODUCT_EM9291 0x90e3 /* UNISOC (Spreadtrum) products */ #define UNISOC_VENDOR_ID 0x1782 @@ -619,15 +620,6 @@ static void option_instat_callback(struct urb *urb); /* Luat Air72*U series based on UNISOC UIS8910 uses UNISOC's vendor ID */ #define LUAT_PRODUCT_AIR720U 0x4e00 -/* MeiG Smart Technology products */ -#define MEIGSMART_VENDOR_ID 0x2dee -/* MeiG Smart SRM815/SRM825L based on Qualcomm 315 */ -#define MEIGSMART_PRODUCT_SRM825L 0x4d22 -/* MeiG Smart SLM320 based on UNISOC UIS8910 */ -#define MEIGSMART_PRODUCT_SLM320 0x4d41 -/* MeiG Smart SLM770A based on ASR1803 */ -#define MEIGSMART_PRODUCT_SLM770A 0x4d57 - /* Device flags */ /* Highest interface number which can be used with NCTRL() and RSVD() */ @@ -1367,23 +1359,23 @@ static const struct usb_device_id option_ids[] = { .driver_info = NCTRL(2) | RSVD(3) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1063, 0xff), /* Telit LN920 (ECM) */ .driver_info = NCTRL(0) | RSVD(1) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1070, 0xff), /* Telit FN990 (rmnet) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1070, 0xff), /* Telit FN990A (rmnet) */ .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1071, 0xff), /* Telit FN990 (MBIM) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1071, 0xff), /* Telit FN990A (MBIM) */ .driver_info = NCTRL(0) | RSVD(1) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1072, 0xff), /* Telit FN990 (RNDIS) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1072, 0xff), /* Telit FN990A (RNDIS) */ .driver_info = NCTRL(2) | RSVD(3) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1073, 0xff), /* Telit FN990 (ECM) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1073, 0xff), /* Telit FN990A (ECM) */ .driver_info = NCTRL(0) | RSVD(1) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1075, 0xff), /* Telit FN990 (PCIe) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1075, 0xff), /* Telit FN990A (PCIe) */ .driver_info = RSVD(0) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1080, 0xff), /* Telit FE990 (rmnet) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1080, 0xff), /* Telit FE990A (rmnet) */ .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1081, 0xff), /* Telit FE990 (MBIM) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1081, 0xff), /* Telit FE990A (MBIM) */ .driver_info = NCTRL(0) | RSVD(1) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1082, 0xff), /* Telit FE990 (RNDIS) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1082, 0xff), /* Telit FE990A (RNDIS) */ .driver_info = NCTRL(2) | RSVD(3) }, - { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1083, 0xff), /* Telit FE990 (ECM) */ + { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1083, 0xff), /* Telit FE990A (ECM) */ .driver_info = NCTRL(0) | RSVD(1) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a0, 0xff), /* Telit FN20C04 (rmnet) */ .driver_info = RSVD(0) | NCTRL(3) }, @@ -1397,12 +1389,44 @@ static const struct usb_device_id option_ids[] = { .driver_info = RSVD(0) | NCTRL(2) | RSVD(3) | RSVD(4) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10aa, 0xff), /* Telit FN920C04 (MBIM) */ .driver_info = NCTRL(3) | RSVD(4) | RSVD(5) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b0, 0xff, 0xff, 0x30), /* Telit FE990B (rmnet) */ + .driver_info = NCTRL(5) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b0, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b0, 0xff, 0xff, 0x60) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b1, 0xff, 0xff, 0x30), /* Telit FE990B (MBIM) */ + .driver_info = NCTRL(6) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b1, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b1, 0xff, 0xff, 0x60) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b2, 0xff, 0xff, 0x30), /* Telit FE990B (RNDIS) */ + .driver_info = NCTRL(6) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b2, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b2, 0xff, 0xff, 0x60) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b3, 0xff, 0xff, 0x30), /* Telit FE990B (ECM) */ + .driver_info = NCTRL(6) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b3, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10b3, 0xff, 0xff, 0x60) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10c0, 0xff), /* Telit FE910C04 (rmnet) */ .driver_info = RSVD(0) | NCTRL(3) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10c4, 0xff), /* Telit FE910C04 (rmnet) */ .driver_info = RSVD(0) | NCTRL(3) }, { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10c8, 0xff), /* Telit FE910C04 (rmnet) */ .driver_info = RSVD(0) | NCTRL(2) | RSVD(3) | RSVD(4) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d0, 0xff, 0xff, 0x30), /* Telit FN990B (rmnet) */ + .driver_info = NCTRL(5) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d0, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d0, 0xff, 0xff, 0x60) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d1, 0xff, 0xff, 0x30), /* Telit FN990B (MBIM) */ + .driver_info = NCTRL(6) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d1, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d1, 0xff, 0xff, 0x60) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d2, 0xff, 0xff, 0x30), /* Telit FN990B (RNDIS) */ + .driver_info = NCTRL(6) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d2, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d2, 0xff, 0xff, 0x60) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d3, 0xff, 0xff, 0x30), /* Telit FN990B (ECM) */ + .driver_info = NCTRL(6) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d3, 0xff, 0xff, 0x40) }, + { USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x10d3, 0xff, 0xff, 0x60) }, { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910), .driver_info = NCTRL(0) | RSVD(1) | RSVD(3) }, { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910_DUAL_MODEM), @@ -2347,6 +2371,14 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a05, 0xff) }, /* Fibocom FM650-CN (NCM mode) */ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a06, 0xff) }, /* Fibocom FM650-CN (RNDIS mode) */ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0a07, 0xff) }, /* Fibocom FM650-CN (MBIM mode) */ + { USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d41, 0xff, 0, 0) }, /* MeiG Smart SLM320 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d57, 0xff, 0, 0) }, /* MeiG Smart SLM770A */ + { USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0, 0) }, /* MeiG Smart SRM815 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0x10, 0x02) }, /* MeiG Smart SLM828 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0x10, 0x03) }, /* MeiG Smart SLM828 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0xff, 0x30) }, /* MeiG Smart SRM815 and SRM825L */ + { USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0xff, 0x40) }, /* MeiG Smart SRM825L */ + { USB_DEVICE_AND_INTERFACE_INFO(0x2dee, 0x4d22, 0xff, 0xff, 0x60) }, /* MeiG Smart SRM825L */ { USB_DEVICE_INTERFACE_CLASS(0x2df3, 0x9d03, 0xff) }, /* LongSung M5710 */ { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff) }, /* GosunCn GM500 RNDIS */ { USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff) }, /* GosunCn GM500 MBIM */ @@ -2401,14 +2433,10 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0xff, 0x30) }, { USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0xff, 0x40) }, { USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0, 0) }, + { USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9291, 0xff, 0xff, 0x30) }, + { USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9291, 0xff, 0xff, 0x40) }, { USB_DEVICE_AND_INTERFACE_INFO(UNISOC_VENDOR_ID, TOZED_PRODUCT_LT70C, 0xff, 0, 0) }, { USB_DEVICE_AND_INTERFACE_INFO(UNISOC_VENDOR_ID, LUAT_PRODUCT_AIR720U, 0xff, 0, 0) }, - { USB_DEVICE_AND_INTERFACE_INFO(MEIGSMART_VENDOR_ID, MEIGSMART_PRODUCT_SLM320, 0xff, 0, 0) }, - { USB_DEVICE_AND_INTERFACE_INFO(MEIGSMART_VENDOR_ID, MEIGSMART_PRODUCT_SLM770A, 0xff, 0, 0) }, - { USB_DEVICE_AND_INTERFACE_INFO(MEIGSMART_VENDOR_ID, MEIGSMART_PRODUCT_SRM825L, 0xff, 0, 0) }, - { USB_DEVICE_AND_INTERFACE_INFO(MEIGSMART_VENDOR_ID, MEIGSMART_PRODUCT_SRM825L, 0xff, 0xff, 0x30) }, - { USB_DEVICE_AND_INTERFACE_INFO(MEIGSMART_VENDOR_ID, MEIGSMART_PRODUCT_SRM825L, 0xff, 0xff, 0x40) }, - { USB_DEVICE_AND_INTERFACE_INFO(MEIGSMART_VENDOR_ID, MEIGSMART_PRODUCT_SRM825L, 0xff, 0xff, 0x60) }, { USB_DEVICE_INTERFACE_CLASS(0x1bbb, 0x0530, 0xff), /* TCL IK512 MBIM */ .driver_info = NCTRL(1) }, { USB_DEVICE_INTERFACE_CLASS(0x1bbb, 0x0640, 0xff), /* TCL IK512 ECM */ diff --git a/drivers/usb/serial/quatech2.c b/drivers/usb/serial/quatech2.c index 971907f083a3..0207ab7ce099 100644 --- a/drivers/usb/serial/quatech2.c +++ b/drivers/usb/serial/quatech2.c @@ -525,7 +525,7 @@ static void qt2_process_read_urb(struct urb *urb) newport = *(ch + 3); - if (newport > serial->num_ports) { + if (newport >= serial->num_ports) { dev_err(&port->dev, "%s - port change to invalid port: %i\n", __func__, newport); diff --git a/drivers/usb/serial/usb-serial-simple.c b/drivers/usb/serial/usb-serial-simple.c index 24b8772a345e..bac5ab6377ae 100644 --- a/drivers/usb/serial/usb-serial-simple.c +++ b/drivers/usb/serial/usb-serial-simple.c @@ -101,6 +101,11 @@ DEVICE(nokia, NOKIA_IDS); { USB_DEVICE(0x09d7, 0x0100) } /* NovAtel FlexPack GPS */ DEVICE_N(novatel_gps, NOVATEL_IDS, 3); +/* OWON electronic test and measurement equipment driver */ +#define OWON_IDS() \ + { USB_DEVICE(0x5345, 0x1234) } /* HDS200 oscilloscopes and others */ +DEVICE(owon, OWON_IDS); + /* Siemens USB/MPI adapter */ #define SIEMENS_IDS() \ { USB_DEVICE(0x908, 0x0004) } @@ -135,6 +140,7 @@ static struct usb_serial_driver * const serial_drivers[] = { &motorola_tetra_device, &nokia_device, &novatel_gps_device, + &owon_device, &siemens_mpi_device, &suunto_device, &vivopay_device, @@ -154,6 +160,7 @@ static const struct usb_device_id id_table[] = { MOTOROLA_TETRA_IDS(), NOKIA_IDS(), NOVATEL_IDS(), + OWON_IDS(), SIEMENS_IDS(), SUUNTO_IDS(), VIVOPAY_IDS(), diff --git a/drivers/usb/storage/unusual_uas.h b/drivers/usb/storage/unusual_uas.h index 1f8c9b16a0fb..d460d71b4257 100644 --- a/drivers/usb/storage/unusual_uas.h +++ b/drivers/usb/storage/unusual_uas.h @@ -83,6 +83,13 @@ UNUSUAL_DEV(0x0bc2, 0x331a, 0x0000, 0x9999, USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_NO_REPORT_LUNS), +/* Reported-by: Oliver Neukum <oneukum@suse.com> */ +UNUSUAL_DEV(0x125f, 0xa94a, 0x0160, 0x0160, + "ADATA", + "Portable HDD CH94", + USB_SC_DEVICE, USB_PR_DEVICE, NULL, + US_FL_NO_ATA_1X), + /* Reported-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> */ UNUSUAL_DEV(0x13fd, 0x3940, 0x0000, 0x9999, "Initio Corporation", diff --git a/drivers/usb/typec/tcpm/tcpci.c b/drivers/usb/typec/tcpm/tcpci.c index 19b80bc8c5dc..e7e1e27cef92 100644 --- a/drivers/usb/typec/tcpm/tcpci.c +++ b/drivers/usb/typec/tcpm/tcpci.c @@ -27,6 +27,7 @@ #define VPPS_NEW_MIN_PERCENT 95 #define VPPS_VALID_MIN_MV 100 #define VSINKDISCONNECT_PD_MIN_PERCENT 90 +#define VPPS_SHUTDOWN_MIN_PERCENT 85 #define tcpc_presenting_rd(reg, cc) \ (!(TCPC_ROLE_CTRL_DRP & (reg)) && \ @@ -356,7 +357,8 @@ static int tcpci_enable_auto_vbus_discharge(struct tcpc_dev *dev, bool enable) } static int tcpci_set_auto_vbus_discharge_threshold(struct tcpc_dev *dev, enum typec_pwr_opmode mode, - bool pps_active, u32 requested_vbus_voltage_mv) + bool pps_active, u32 requested_vbus_voltage_mv, + u32 apdo_min_voltage_mv) { struct tcpci *tcpci = tcpc_to_tcpci(dev); unsigned int pwr_ctrl, threshold = 0; @@ -378,9 +380,12 @@ static int tcpci_set_auto_vbus_discharge_threshold(struct tcpc_dev *dev, enum ty threshold = AUTO_DISCHARGE_DEFAULT_THRESHOLD_MV; } else if (mode == TYPEC_PWR_MODE_PD) { if (pps_active) - threshold = ((VPPS_NEW_MIN_PERCENT * requested_vbus_voltage_mv / 100) - - VSINKPD_MIN_IR_DROP_MV - VPPS_VALID_MIN_MV) * - VSINKDISCONNECT_PD_MIN_PERCENT / 100; + /* + * To prevent disconnect when the source is in Current Limit Mode. + * Set the threshold to the lowest possible voltage vPpsShutdown (min) + */ + threshold = VPPS_SHUTDOWN_MIN_PERCENT * apdo_min_voltage_mv / 100 - + VSINKPD_MIN_IR_DROP_MV; else threshold = ((VSRC_NEW_MIN_PERCENT * requested_vbus_voltage_mv / 100) - VSINKPD_MIN_IR_DROP_MV - VSRC_VALID_MIN_MV) * diff --git a/drivers/usb/typec/tcpm/tcpci_rt1711h.c b/drivers/usb/typec/tcpm/tcpci_rt1711h.c index 3291ca4948da..9df13ce036c6 100644 --- a/drivers/usb/typec/tcpm/tcpci_rt1711h.c +++ b/drivers/usb/typec/tcpm/tcpci_rt1711h.c @@ -217,6 +217,11 @@ static int rt1711h_probe(struct i2c_client *client, { int ret; struct rt1711h_chip *chip; + const u16 alert_mask = TCPC_ALERT_TX_SUCCESS | TCPC_ALERT_TX_DISCARDED | + TCPC_ALERT_TX_FAILED | TCPC_ALERT_RX_HARD_RST | + TCPC_ALERT_RX_STATUS | TCPC_ALERT_POWER_STATUS | + TCPC_ALERT_CC_STATUS | TCPC_ALERT_RX_BUF_OVF | + TCPC_ALERT_FAULT; ret = rt1711h_check_revision(client); if (ret < 0) { @@ -258,6 +263,12 @@ static int rt1711h_probe(struct i2c_client *client, dev_name(chip->dev), chip); if (ret < 0) return ret; + + /* Enable alert interrupts */ + ret = rt1711h_write16(chip, TCPC_ALERT_MASK, alert_mask); + if (ret < 0) + return ret; + enable_irq_wake(client->irq); return 0; diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c index 2028f12026da..36040272f138 100644 --- a/drivers/usb/typec/tcpm/tcpm.c +++ b/drivers/usb/typec/tcpm/tcpm.c @@ -2312,10 +2312,12 @@ static int tcpm_set_auto_vbus_discharge_threshold(struct tcpm_port *port, return 0; ret = port->tcpc->set_auto_vbus_discharge_threshold(port->tcpc, mode, pps_active, - requested_vbus_voltage); + requested_vbus_voltage, + port->pps_data.min_volt); tcpm_log_force(port, - "set_auto_vbus_discharge_threshold mode:%d pps_active:%c vbus:%u ret:%d", - mode, pps_active ? 'y' : 'n', requested_vbus_voltage, ret); + "set_auto_vbus_discharge_threshold mode:%d pps_active:%c vbus:%u pps_apdo_min_volt:%u ret:%d", + mode, pps_active ? 'y' : 'n', requested_vbus_voltage, + port->pps_data.min_volt, ret); return ret; } @@ -4037,7 +4039,7 @@ static void run_state_machine(struct tcpm_port *port) port->caps_count = 0; port->pd_capable = true; tcpm_set_state_cond(port, SRC_SEND_CAPABILITIES_TIMEOUT, - PD_T_SEND_SOURCE_CAP); + PD_T_SENDER_RESPONSE); } break; case SRC_SEND_CAPABILITIES_TIMEOUT: @@ -5052,7 +5054,7 @@ static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1, case SNK_TRY_WAIT_DEBOUNCE: if (!tcpm_port_is_sink(port)) { port->max_wait = 0; - tcpm_set_state(port, SRC_TRYWAIT, 0); + tcpm_set_state(port, SRC_TRYWAIT, PD_T_PD_DEBOUNCE); } break; case SRC_TRY_WAIT: diff --git a/drivers/usb/typec/ucsi/displayport.c b/drivers/usb/typec/ucsi/displayport.c index 2431febc4615..8c19081c3255 100644 --- a/drivers/usb/typec/ucsi/displayport.c +++ b/drivers/usb/typec/ucsi/displayport.c @@ -296,6 +296,8 @@ void ucsi_displayport_remove_partner(struct typec_altmode *alt) if (!dp) return; + cancel_work_sync(&dp->work); + dp->data.conf = 0; dp->data.status = 0; dp->initialized = false; diff --git a/drivers/usb/typec/ucsi/ucsi.c b/drivers/usb/typec/ucsi/ucsi.c index cb6458ec042c..979af06f22d8 100644 --- a/drivers/usb/typec/ucsi/ucsi.c +++ b/drivers/usb/typec/ucsi/ucsi.c @@ -25,7 +25,7 @@ * difficult to estimate the time it takes for the system to process the command * before it is actually passed to the PPM. */ -#define UCSI_TIMEOUT_MS 5000 +#define UCSI_TIMEOUT_MS 10000 /* * UCSI_SWAP_TIMEOUT_MS - Timeout for role swap requests |