diff options
Diffstat (limited to 'include/net/cfg80211.h')
| -rw-r--r-- | include/net/cfg80211.h | 459 |
1 files changed, 347 insertions, 112 deletions
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 3a4b684f89bf..2b54fdd8ca15 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -52,7 +52,7 @@ * such wiphy can have zero, one, or many virtual interfaces associated with * it, which need to be identified as such by pointing the network interface's * @ieee80211_ptr pointer to a &struct wireless_dev which further describes - * the wireless part of the interface, normally this struct is embedded in the + * the wireless part of the interface. Normally this struct is embedded in the * network interface's private data area. Drivers can optionally allow creating * or destroying virtual interfaces on the fly, but without at least one or the * ability to create some the wireless device isn't useful. @@ -76,6 +76,8 @@ struct wiphy; * @IEEE80211_CHAN_DISABLED: This channel is disabled. * @IEEE80211_CHAN_NO_IR: do not initiate radiation, this includes * sending probe requests or beaconing. + * @IEEE80211_CHAN_PSD: Power spectral density (in dBm) is set for this + * channel. * @IEEE80211_CHAN_RADAR: Radar detection is required on this channel. * @IEEE80211_CHAN_NO_HT40PLUS: extension channel above this channel * is not permitted. @@ -115,11 +117,16 @@ struct wiphy; * This may be due to the driver or due to regulatory bandwidth * restrictions. * @IEEE80211_CHAN_NO_EHT: EHT operation is not permitted on this channel. + * @IEEE80211_CHAN_DFS_CONCURRENT: See %NL80211_RRF_DFS_CONCURRENT + * @IEEE80211_CHAN_NO_UHB_VLP_CLIENT: Client connection with VLP AP + * not permitted using this channel + * @IEEE80211_CHAN_NO_UHB_AFC_CLIENT: Client connection with AFC AP + * not permitted using this channel */ enum ieee80211_channel_flags { IEEE80211_CHAN_DISABLED = 1<<0, IEEE80211_CHAN_NO_IR = 1<<1, - /* hole at 1<<2 */ + IEEE80211_CHAN_PSD = 1<<2, IEEE80211_CHAN_RADAR = 1<<3, IEEE80211_CHAN_NO_HT40PLUS = 1<<4, IEEE80211_CHAN_NO_HT40MINUS = 1<<5, @@ -138,6 +145,9 @@ enum ieee80211_channel_flags { IEEE80211_CHAN_16MHZ = 1<<18, IEEE80211_CHAN_NO_320MHZ = 1<<19, IEEE80211_CHAN_NO_EHT = 1<<20, + IEEE80211_CHAN_DFS_CONCURRENT = 1<<21, + IEEE80211_CHAN_NO_UHB_VLP_CLIENT= 1<<22, + IEEE80211_CHAN_NO_UHB_AFC_CLIENT= 1<<23, }; #define IEEE80211_CHAN_NO_HT40 \ @@ -171,6 +181,7 @@ enum ieee80211_channel_flags { * on this channel. * @dfs_state_entered: timestamp (jiffies) when the dfs state was entered. * @dfs_cac_ms: DFS CAC time in milliseconds, this is valid for DFS channels. + * @psd: power spectral density (in dBm) */ struct ieee80211_channel { enum nl80211_band band; @@ -187,6 +198,7 @@ struct ieee80211_channel { enum nl80211_dfs_state dfs_state; unsigned long dfs_state_entered; unsigned int dfs_cac_ms; + s8 psd; }; /** @@ -410,6 +422,19 @@ struct ieee80211_sta_eht_cap { u8 eht_ppe_thres[IEEE80211_EHT_PPE_THRES_MAX_LEN]; }; +/* sparse defines __CHECKER__; see Documentation/dev-tools/sparse.rst */ +#ifdef __CHECKER__ +/* + * This is used to mark the sband->iftype_data pointer which is supposed + * to be an array with special access semantics (per iftype), but a lot + * of code got it wrong in the past, so with this marking sparse will be + * noisy when the pointer is used directly. + */ +# define __iftd __attribute__((noderef, address_space(__iftype_data))) +#else +# define __iftd +#endif /* __CHECKER__ */ + /** * struct ieee80211_sband_iftype_data - sband data per interface type * @@ -543,10 +568,48 @@ struct ieee80211_supported_band { struct ieee80211_sta_s1g_cap s1g_cap; struct ieee80211_edmg edmg_cap; u16 n_iftype_data; - const struct ieee80211_sband_iftype_data *iftype_data; + const struct ieee80211_sband_iftype_data __iftd *iftype_data; }; /** + * _ieee80211_set_sband_iftype_data - set sband iftype data array + * @sband: the sband to initialize + * @iftd: the iftype data array pointer + * @n_iftd: the length of the iftype data array + * + * Set the sband iftype data array; use this where the length cannot + * be derived from the ARRAY_SIZE() of the argument, but prefer + * ieee80211_set_sband_iftype_data() where it can be used. + */ +static inline void +_ieee80211_set_sband_iftype_data(struct ieee80211_supported_band *sband, + const struct ieee80211_sband_iftype_data *iftd, + u16 n_iftd) +{ + sband->iftype_data = (const void __iftd __force *)iftd; + sband->n_iftype_data = n_iftd; +} + +/** + * ieee80211_set_sband_iftype_data - set sband iftype data array + * @sband: the sband to initialize + * @iftd: the iftype data array + */ +#define ieee80211_set_sband_iftype_data(sband, iftd) \ + _ieee80211_set_sband_iftype_data(sband, iftd, ARRAY_SIZE(iftd)) + +/** + * for_each_sband_iftype_data - iterate sband iftype data entries + * @sband: the sband whose iftype_data array to iterate + * @i: iterator counter + * @iftd: iftype data pointer to set + */ +#define for_each_sband_iftype_data(sband, i, iftd) \ + for (i = 0, iftd = (const void __force *)&(sband)->iftype_data[i]; \ + i < (sband)->n_iftype_data; \ + i++, iftd = (const void __force *)&(sband)->iftype_data[i]) + +/** * ieee80211_get_sband_iftype_data - return sband data for a given iftype * @sband: the sband to search for the STA on * @iftype: enum nl80211_iftype @@ -557,6 +620,7 @@ static inline const struct ieee80211_sband_iftype_data * ieee80211_get_sband_iftype_data(const struct ieee80211_supported_band *sband, u8 iftype) { + const struct ieee80211_sband_iftype_data *data; int i; if (WARN_ON(iftype >= NL80211_IFTYPE_MAX)) @@ -565,10 +629,7 @@ ieee80211_get_sband_iftype_data(const struct ieee80211_supported_band *sband, if (iftype == NL80211_IFTYPE_AP_VLAN) iftype = NL80211_IFTYPE_AP; - for (i = 0; i < sband->n_iftype_data; i++) { - const struct ieee80211_sband_iftype_data *data = - &sband->iftype_data[i]; - + for_each_sband_iftype_data(sband, i, data) { if (data->types_mask & BIT(iftype)) return data; } @@ -924,6 +985,15 @@ cfg80211_chandef_compatible(const struct cfg80211_chan_def *chandef1, const struct cfg80211_chan_def *chandef2); /** + * nl80211_chan_width_to_mhz - get the channel width in MHz + * @chan_width: the channel width from &enum nl80211_chan_width + * + * Return: channel width in MHz if the chan_width from &enum nl80211_chan_width + * is valid. -1 otherwise. + */ +int nl80211_chan_width_to_mhz(enum nl80211_chan_width chan_width); + +/** * cfg80211_chandef_valid - check if a channel definition is valid * @chandef: the channel definition to check * Return: %true if the channel definition is valid. %false otherwise. @@ -954,6 +1024,30 @@ int cfg80211_chandef_dfs_required(struct wiphy *wiphy, enum nl80211_iftype iftype); /** + * cfg80211_chandef_dfs_usable - checks if chandef is DFS usable and we + * can/need start CAC on such channel + * @wiphy: the wiphy to validate against + * @chandef: the channel definition to check + * + * Return: true if all channels available and at least + * one channel requires CAC (NL80211_DFS_USABLE) + */ +bool cfg80211_chandef_dfs_usable(struct wiphy *wiphy, + const struct cfg80211_chan_def *chandef); + +/** + * cfg80211_chandef_dfs_cac_time - get the DFS CAC time (in ms) for given + * channel definition + * @wiphy: the wiphy to validate against + * @chandef: the channel definition to check + * + * Returns: DFS CAC time (in ms) which applies for this channel definition + */ +unsigned int +cfg80211_chandef_dfs_cac_time(struct wiphy *wiphy, + const struct cfg80211_chan_def *chandef); + +/** * nl80211_send_chandef - sends the channel definition. * @msg: the msg to send channel definition * @chandef: the channel definition to check @@ -1289,6 +1383,7 @@ struct cfg80211_acl_data { * struct cfg80211_fils_discovery - FILS discovery parameters from * IEEE Std 802.11ai-2016, Annex C.3 MIB detail. * + * @update: Set to true if the feature configuration should be updated. * @min_interval: Minimum packet interval in TUs (0 - 10000) * @max_interval: Maximum packet interval in TUs (0 - 10000) * @tmpl_len: Template length @@ -1296,6 +1391,7 @@ struct cfg80211_acl_data { * frame headers. */ struct cfg80211_fils_discovery { + bool update; u32 min_interval; u32 max_interval; size_t tmpl_len; @@ -1306,6 +1402,7 @@ struct cfg80211_fils_discovery { * struct cfg80211_unsol_bcast_probe_resp - Unsolicited broadcast probe * response parameters in 6GHz. * + * @update: Set to true if the feature configuration should be updated. * @interval: Packet interval in TUs. Maximum allowed is 20 TU, as mentioned * in IEEE P802.11ax/D6.0 26.17.2.3.2 - AP behavior for fast passive * scanning @@ -1313,6 +1410,7 @@ struct cfg80211_fils_discovery { * @tmpl: Template data for probe response */ struct cfg80211_unsol_bcast_probe_resp { + bool update; u32 interval; size_t tmpl_len; const u8 *tmpl; @@ -1399,6 +1497,22 @@ struct cfg80211_ap_settings { u16 punct_bitmap; }; + +/** + * struct cfg80211_ap_update - AP configuration update + * + * Subset of &struct cfg80211_ap_settings, for updating a running AP. + * + * @beacon: beacon data + * @fils_discovery: FILS discovery transmission parameters + * @unsol_bcast_probe_resp: Unsolicited broadcast probe response parameters + */ +struct cfg80211_ap_update { + struct cfg80211_beacon_data beacon; + struct cfg80211_fils_discovery fils_discovery; + struct cfg80211_unsol_bcast_probe_resp unsol_bcast_probe_resp; +}; + /** * struct cfg80211_csa_settings - channel switch settings * @@ -1568,6 +1682,21 @@ struct link_station_del_parameters { }; /** + * struct cfg80211_ttlm_params: TID to link mapping parameters + * + * Used for setting a TID to link mapping. + * + * @dlink: Downlink TID to link mapping, as defined in section 9.4.2.314 + * (TID-To-Link Mapping element) in Draft P802.11be_D4.0. + * @ulink: Uplink TID to link mapping, as defined in section 9.4.2.314 + * (TID-To-Link Mapping element) in Draft P802.11be_D4.0. + */ +struct cfg80211_ttlm_params { + u16 dlink[8]; + u16 ulink[8]; +}; + +/** * struct station_parameters - station parameters * * Used to change and create a new station. @@ -2346,7 +2475,7 @@ struct mesh_config { * @user_mpm: userspace handles all MPM functions * @dtim_period: DTIM period to use * @beacon_interval: beacon interval to use - * @mcast_rate: multicat rate for Mesh Node [6Mbps is the default for 802.11a] + * @mcast_rate: multicast rate for Mesh Node [6Mbps is the default for 802.11a] * @basic_rates: basic rates to use when creating the mesh * @beacon_rate: bitrate to be used for beacons * @userspace_handles_dfs: whether user space controls DFS operation, i.e. @@ -2463,7 +2592,7 @@ struct cfg80211_scan_info { * @short_ssid: short ssid to scan for * @bssid: bssid to scan for * @channel_idx: idx of the channel in the channel array in the scan request - * which the above info relvant to + * which the above info is relevant to * @unsolicited_probe: the AP transmits unsolicited probe response every 20 TU * @short_ssid_valid: @short_ssid is valid and can be used * @psc_no_listen: when set, and the channel is a PSC channel, no need to wait @@ -2487,7 +2616,6 @@ struct cfg80211_scan_6ghz_params { * @n_ssids: number of SSIDs * @channels: channels to scan on. * @n_channels: total number of channels to scan - * @scan_width: channel width for scanning * @ie: optional information element(s) to add into Probe Request or %NULL * @ie_len: length of ie in octets * @duration: how long to listen on each channel, in TUs. If @@ -2512,12 +2640,13 @@ struct cfg80211_scan_6ghz_params { * @n_6ghz_params: number of 6 GHz params * @scan_6ghz_params: 6 GHz params * @bssid: BSSID to scan for (most commonly, the wildcard BSSID) + * @tsf_report_link_id: for MLO, indicates the link ID of the BSS that should be + * used for TSF reporting. Can be set to -1 to indicate no preference. */ struct cfg80211_scan_request { struct cfg80211_ssid *ssids; int n_ssids; u32 n_channels; - enum nl80211_bss_scan_width scan_width; const u8 *ie; size_t ie_len; u16 duration; @@ -2541,6 +2670,7 @@ struct cfg80211_scan_request { bool scan_6ghz; u32 n_6ghz_params; struct cfg80211_scan_6ghz_params *scan_6ghz_params; + s8 tsf_report_link_id; /* keep last */ struct ieee80211_channel *channels[] __counted_by(n_channels); @@ -2566,7 +2696,7 @@ static inline void get_random_mask_addr(u8 *buf, const u8 *addr, const u8 *mask) * or no match (RSSI only) * @rssi_thold: don't report scan results below this threshold (in s32 dBm) * @per_band_rssi_thold: Minimum rssi threshold for each band to be applied - * for filtering out scan results received. Drivers advertize this support + * for filtering out scan results received. Drivers advertise this support * of band specific rssi based filtering through the feature capability * %NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD. These band * specific rssi thresholds take precedence over rssi_thold, if specified. @@ -2612,14 +2742,13 @@ struct cfg80211_bss_select_adjust { * @ssids: SSIDs to scan for (passed in the probe_reqs in active scans) * @n_ssids: number of SSIDs * @n_channels: total number of channels to scan - * @scan_width: channel width for scanning * @ie: optional information element(s) to add into Probe Request or %NULL * @ie_len: length of ie in octets * @flags: control flags from &enum nl80211_scan_flags * @match_sets: sets of parameters to be matched for a scan result * entry to be considered valid and to be passed to the host * (others are filtered out). - * If ommited, all results are passed. + * If omitted, all results are passed. * @n_match_sets: number of match sets * @report_results: indicates that results were reported for this request * @wiphy: the wiphy this was for @@ -2653,14 +2782,13 @@ struct cfg80211_bss_select_adjust { * to the specified band while deciding whether a better BSS is reported * using @relative_rssi. If delta is a negative number, the BSSs that * belong to the specified band will be penalized by delta dB in relative - * comparisions. + * comparisons. */ struct cfg80211_sched_scan_request { u64 reqid; struct cfg80211_ssid *ssids; int n_ssids; u32 n_channels; - enum nl80211_bss_scan_width scan_width; const u8 *ie; size_t ie_len; u32 flags; @@ -2708,7 +2836,6 @@ enum cfg80211_signal_type { /** * struct cfg80211_inform_bss - BSS inform data * @chan: channel the frame was received on - * @scan_width: scan width that was used * @signal: signal strength value, according to the wiphy's * signal type * @boottime_ns: timestamp (CLOCK_BOOTTIME) when the information was @@ -2724,11 +2851,17 @@ enum cfg80211_signal_type { * the BSS that requested the scan in which the beacon/probe was received. * @chains: bitmask for filled values in @chain_signal. * @chain_signal: per-chain signal strength of last received BSS in dBm. + * @restrict_use: restrict usage, if not set, assume @use_for is + * %NL80211_BSS_USE_FOR_NORMAL. + * @use_for: bitmap of possible usage for this BSS, see + * &enum nl80211_bss_use_for + * @cannot_use_reasons: the reasons (bitmap) for not being able to connect, + * if @restrict_use is set and @use_for is zero (empty); may be 0 for + * unspecified reasons; see &enum nl80211_bss_cannot_use_reasons * @drv_data: Data to be passed through to @inform_bss */ struct cfg80211_inform_bss { struct ieee80211_channel *chan; - enum nl80211_bss_scan_width scan_width; s32 signal; u64 boottime_ns; u64 parent_tsf; @@ -2736,6 +2869,9 @@ struct cfg80211_inform_bss { u8 chains; s8 chain_signal[IEEE80211_MAX_CHAINS]; + u8 restrict_use:1, use_for:7; + u8 cannot_use_reasons; + void *drv_data; }; @@ -2762,7 +2898,6 @@ struct cfg80211_bss_ies { * for use in scan results and similar. * * @channel: channel this BSS is on - * @scan_width: width of the control channel * @bssid: BSSID of the BSS * @beacon_interval: the beacon interval as from the frame * @capability: the capability field in host byte order @@ -2775,6 +2910,8 @@ struct cfg80211_bss_ies { * own the beacon_ies, but they're just pointers to the ones from the * @hidden_beacon_bss struct) * @proberesp_ies: the information elements from the last Probe Response frame + * @proberesp_ecsa_stuck: ECSA element is stuck in the Probe Response frame, + * cannot rely on it having valid data * @hidden_beacon_bss: in case this BSS struct represents a probe response from * a BSS that hides the SSID in its beacon, this points to the BSS struct * that holds the beacon data. @beacon_ies is still valid, of course, and @@ -2788,11 +2925,15 @@ struct cfg80211_bss_ies { * @chain_signal: per-chain signal strength of last received BSS in dBm. * @bssid_index: index in the multiple BSS set * @max_bssid_indicator: max number of members in the BSS set + * @use_for: bitmap of possible usage for this BSS, see + * &enum nl80211_bss_use_for + * @cannot_use_reasons: the reasons (bitmap) for not being able to connect, + * if @restrict_use is set and @use_for is zero (empty); may be 0 for + * unspecified reasons; see &enum nl80211_bss_cannot_use_reasons * @priv: private area for driver use, has at least wiphy->bss_priv_size bytes */ struct cfg80211_bss { struct ieee80211_channel *channel; - enum nl80211_bss_scan_width scan_width; const struct cfg80211_bss_ies __rcu *ies; const struct cfg80211_bss_ies __rcu *beacon_ies; @@ -2811,9 +2952,14 @@ struct cfg80211_bss { u8 chains; s8 chain_signal[IEEE80211_MAX_CHAINS]; + u8 proberesp_ecsa_stuck:1; + u8 bssid_index; u8 max_bssid_indicator; + u8 use_for; + u8 cannot_use_reasons; + u8 priv[] __aligned(sizeof(void *)); }; @@ -2891,12 +3037,15 @@ struct cfg80211_auth_request { * @elems_len: length of the elements * @disabled: If set this link should be included during association etc. but it * should not be used until enabled by the AP MLD. + * @error: per-link error code, must be <= 0. If there is an error, then the + * operation as a whole must fail. */ struct cfg80211_assoc_link { struct cfg80211_bss *bss; const u8 *elems; size_t elems_len; bool disabled; + int error; }; /** @@ -3088,8 +3237,8 @@ struct cfg80211_ibss_params { * * @behaviour: requested BSS selection behaviour. * @param: parameters for requestion behaviour. - * @band_pref: preferred band for %NL80211_BSS_SELECT_ATTR_BAND_PREF. - * @adjust: parameters for %NL80211_BSS_SELECT_ATTR_RSSI_ADJUST. + * @param.band_pref: preferred band for %NL80211_BSS_SELECT_ATTR_BAND_PREF. + * @param.adjust: parameters for %NL80211_BSS_SELECT_ATTR_RSSI_ADJUST. */ struct cfg80211_bss_selection { enum nl80211_bss_select_attr behaviour; @@ -3495,7 +3644,7 @@ struct cfg80211_update_ft_ies_params { * This structure provides information needed to transmit a mgmt frame * * @chan: channel to use - * @offchan: indicates wether off channel operation is required + * @offchan: indicates whether off channel operation is required * @wait: duration for ROC * @buf: buffer to transmit * @len: buffer length @@ -3613,7 +3762,7 @@ struct cfg80211_nan_func_filter { * @publish_bcast: if true, the solicited publish should be broadcasted * @subscribe_active: if true, the subscribe is active * @followup_id: the instance ID for follow up - * @followup_reqid: the requestor instance ID for follow up + * @followup_reqid: the requester instance ID for follow up * @followup_dest: MAC address of the recipient of the follow up * @ttl: time to live counter in DW. * @serv_spec_info: Service Specific Info @@ -4401,6 +4550,7 @@ struct mgmt_frame_regs { * @del_link_station: Remove a link of a station. * * @set_hw_timestamp: Enable/disable HW timestamping of TM/FTM frames. + * @set_ttlm: set the TID to link mapping. */ struct cfg80211_ops { int (*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow); @@ -4450,7 +4600,7 @@ struct cfg80211_ops { int (*start_ap)(struct wiphy *wiphy, struct net_device *dev, struct cfg80211_ap_settings *settings); int (*change_beacon)(struct wiphy *wiphy, struct net_device *dev, - struct cfg80211_beacon_data *info); + struct cfg80211_ap_update *info); int (*stop_ap)(struct wiphy *wiphy, struct net_device *dev, unsigned int link_id); @@ -4760,6 +4910,8 @@ struct cfg80211_ops { struct link_station_del_parameters *params); int (*set_hw_timestamp)(struct wiphy *wiphy, struct net_device *dev, struct cfg80211_set_hw_timestamp *hwts); + int (*set_ttlm)(struct wiphy *wiphy, struct net_device *dev, + struct cfg80211_ttlm_params *params); }; /* @@ -4816,6 +4968,10 @@ struct cfg80211_ops { * @WIPHY_FLAG_SUPPORTS_EXT_KCK_32: The device supports 32-byte KCK keys. * @WIPHY_FLAG_NOTIFY_REGDOM_BY_DRIVER: The device could handle reg notify for * NL80211_REGDOM_SET_BY_DRIVER. + * @WIPHY_FLAG_CHANNEL_CHANGE_ON_BEACON: reg_call_notifier() is called if driver + * set this flag to update channels on beacon hints. + * @WIPHY_FLAG_SUPPORTS_NSTR_NONPRIMARY: support connection to non-primary link + * of an NSTR mobile AP MLD. */ enum wiphy_flags { WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK = BIT(0), @@ -4829,7 +4985,7 @@ enum wiphy_flags { WIPHY_FLAG_IBSS_RSN = BIT(8), WIPHY_FLAG_MESH_AUTH = BIT(10), WIPHY_FLAG_SUPPORTS_EXT_KCK_32 = BIT(11), - /* use hole at 12 */ + WIPHY_FLAG_SUPPORTS_NSTR_NONPRIMARY = BIT(12), WIPHY_FLAG_SUPPORTS_FW_ROAM = BIT(13), WIPHY_FLAG_AP_UAPSD = BIT(14), WIPHY_FLAG_SUPPORTS_TDLS = BIT(15), @@ -4842,6 +4998,7 @@ enum wiphy_flags { WIPHY_FLAG_SUPPORTS_5_10_MHZ = BIT(22), WIPHY_FLAG_HAS_CHANNEL_SWITCH = BIT(23), WIPHY_FLAG_NOTIFY_REGDOM_BY_DRIVER = BIT(24), + WIPHY_FLAG_CHANNEL_CHANGE_ON_BEACON = BIT(25), }; /** @@ -5826,6 +5983,16 @@ void wiphy_work_queue(struct wiphy *wiphy, struct wiphy_work *work); */ void wiphy_work_cancel(struct wiphy *wiphy, struct wiphy_work *work); +/** + * wiphy_work_flush - flush previously queued work + * @wiphy: the wiphy, for debug purposes + * @work: the work to flush, this can be %NULL to flush all work + * + * Flush the work (i.e. run it if pending). This must be called + * under the wiphy mutex acquired by wiphy_lock(). + */ +void wiphy_work_flush(struct wiphy *wiphy, struct wiphy_work *work); + struct wiphy_delayed_work { struct wiphy_work work; struct wiphy *wiphy; @@ -5870,6 +6037,17 @@ void wiphy_delayed_work_cancel(struct wiphy *wiphy, struct wiphy_delayed_work *dwork); /** + * wiphy_delayed_work_flush - flush previously queued delayed work + * @wiphy: the wiphy, for debug purposes + * @dwork: the delayed work to flush + * + * Flush the work (i.e. run it if pending). This must be called + * under the wiphy mutex acquired by wiphy_lock(). + */ +void wiphy_delayed_work_flush(struct wiphy *wiphy, + struct wiphy_delayed_work *dwork); + +/** * struct wireless_dev - wireless device state * * For netdevs, this structure must be allocated by the driver @@ -5897,7 +6075,6 @@ void wiphy_delayed_work_cancel(struct wiphy *wiphy, * wireless device if it has no netdev * @u: union containing data specific to @iftype * @connected: indicates if connected or not (STA mode) - * @bssid: (private) Used by the internal configuration code * @wext: (private) Used by the internal wireless extensions compat code * @wext.ibss: (private) IBSS data part of wext handling * @wext.connect: (private) connection handling data @@ -5917,10 +6094,6 @@ void wiphy_delayed_work_cancel(struct wiphy *wiphy, * @mgmt_registrations: list of registrations for management frames * @mgmt_registrations_need_update: mgmt registrations were updated, * need to propagate the update to the driver - * @mtx: mutex used to lock data in this struct, may be used by drivers - * and some API functions require it held - * @beacon_interval: beacon interval used on this device for transmitting - * beacons, 0 when not valid * @address: The address for this device, valid only if @netdev is %NULL * @is_running: true if this is a non-netdev device that has been started, e.g. * the P2P Device. @@ -5941,6 +6114,7 @@ void wiphy_delayed_work_cancel(struct wiphy *wiphy, * @event_lock: (private) lock for event list * @owner_nlportid: (private) owner socket port ID * @nl_owner_dead: (private) owner socket went away + * @cqm_rssi_work: (private) CQM RSSI reporting work * @cqm_config: (private) nl80211 RSSI monitor state * @pmsr_list: (private) peer measurement requests * @pmsr_lock: (private) peer measurements requests/results lock @@ -5964,8 +6138,6 @@ struct wireless_dev { struct list_head mgmt_registrations; u8 mgmt_registrations_need_update:1; - struct mutex mtx; - bool use_4addr, is_running, registered, registering; u8 address[ETH_ALEN] __aligned(sizeof(u16)); @@ -6013,7 +6185,8 @@ struct wireless_dev { } wext; #endif - struct cfg80211_cqm_config *cqm_config; + struct wiphy_work cqm_rssi_work; + struct cfg80211_cqm_config __rcu *cqm_config; struct list_head pmsr_list; spinlock_t pmsr_lock; @@ -6255,13 +6428,11 @@ ieee80211_get_response_rate(struct ieee80211_supported_band *sband, /** * ieee80211_mandatory_rates - get mandatory rates for a given band * @sband: the band to look for rates in - * @scan_width: width of the control channel * * This function returns a bitmap of the mandatory rates for the given * band, bits are set according to the rate position in the bitrates array. */ -u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband, - enum nl80211_bss_scan_width scan_width); +u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband); /* * Radiotap parsing functions -- for controlled injection support @@ -6602,7 +6773,7 @@ static inline const u8 *cfg80211_find_ie(u8 eid, const u8 *ies, int len) * @ies: data consisting of IEs * @len: length of data * - * Return: %NULL if the etended element could not be found or if + * Return: %NULL if the extended element could not be found or if * the element is invalid (claims to be longer than the given * data) or if the byte array doesn't match; otherwise return the * requested element struct. @@ -6749,7 +6920,7 @@ int regulatory_hint(struct wiphy *wiphy, const char *alpha2); /** * regulatory_set_wiphy_regd - set regdom info for self managed drivers * @wiphy: the wireless device we want to process the regulatory domain on - * @rd: the regulatory domain informatoin to use for this wiphy + * @rd: the regulatory domain information to use for this wiphy * * Set the regulatory domain information for self-managed wiphys, only they * may use this function. See %REGULATORY_WIPHY_SELF_MANAGED for more @@ -6840,7 +7011,7 @@ bool regulatory_pre_cac_allowed(struct wiphy *wiphy); * Regulatory self-managed driver can use it to proactively * * @alpha2: the ISO/IEC 3166 alpha2 wmm rule to be queried. - * @freq: the freqency(in MHz) to be queried. + * @freq: the frequency (in MHz) to be queried. * @rule: pointer to store the wmm rule from the regulatory db. * * Self-managed wireless drivers can use this function to query @@ -6923,22 +7094,6 @@ cfg80211_inform_bss_frame_data(struct wiphy *wiphy, gfp_t gfp); static inline struct cfg80211_bss * __must_check -cfg80211_inform_bss_width_frame(struct wiphy *wiphy, - struct ieee80211_channel *rx_channel, - enum nl80211_bss_scan_width scan_width, - struct ieee80211_mgmt *mgmt, size_t len, - s32 signal, gfp_t gfp) -{ - struct cfg80211_inform_bss data = { - .chan = rx_channel, - .scan_width = scan_width, - .signal = signal, - }; - - return cfg80211_inform_bss_frame_data(wiphy, &data, mgmt, len, gfp); -} - -static inline struct cfg80211_bss * __must_check cfg80211_inform_bss_frame(struct wiphy *wiphy, struct ieee80211_channel *rx_channel, struct ieee80211_mgmt *mgmt, size_t len, @@ -6946,7 +7101,6 @@ cfg80211_inform_bss_frame(struct wiphy *wiphy, { struct cfg80211_inform_bss data = { .chan = rx_channel, - .scan_width = NL80211_BSS_CHAN_WIDTH_20, .signal = signal, }; @@ -7021,6 +7175,23 @@ int cfg80211_get_ies_channel_number(const u8 *ie, size_t ielen, enum nl80211_band band); /** + * cfg80211_ssid_eq - compare two SSIDs + * @a: first SSID + * @b: second SSID + * + * Return: %true if SSIDs are equal, %false otherwise. + */ +static inline bool +cfg80211_ssid_eq(struct cfg80211_ssid *a, struct cfg80211_ssid *b) +{ + if (WARN_ON(!a || !b)) + return false; + if (a->ssid_len != b->ssid_len) + return false; + return memcmp(a->ssid, b->ssid, a->ssid_len) ? false : true; +} + +/** * cfg80211_inform_bss_data - inform cfg80211 of a new BSS * * @wiphy: the wiphy reporting the BSS @@ -7049,26 +7220,6 @@ cfg80211_inform_bss_data(struct wiphy *wiphy, gfp_t gfp); static inline struct cfg80211_bss * __must_check -cfg80211_inform_bss_width(struct wiphy *wiphy, - struct ieee80211_channel *rx_channel, - enum nl80211_bss_scan_width scan_width, - enum cfg80211_bss_frame_type ftype, - const u8 *bssid, u64 tsf, u16 capability, - u16 beacon_interval, const u8 *ie, size_t ielen, - s32 signal, gfp_t gfp) -{ - struct cfg80211_inform_bss data = { - .chan = rx_channel, - .scan_width = scan_width, - .signal = signal, - }; - - return cfg80211_inform_bss_data(wiphy, &data, ftype, bssid, tsf, - capability, beacon_interval, ie, ielen, - gfp); -} - -static inline struct cfg80211_bss * __must_check cfg80211_inform_bss(struct wiphy *wiphy, struct ieee80211_channel *rx_channel, enum cfg80211_bss_frame_type ftype, @@ -7078,7 +7229,6 @@ cfg80211_inform_bss(struct wiphy *wiphy, { struct cfg80211_inform_bss data = { .chan = rx_channel, - .scan_width = NL80211_BSS_CHAN_WIDTH_20, .signal = signal, }; @@ -7088,6 +7238,25 @@ cfg80211_inform_bss(struct wiphy *wiphy, } /** + * __cfg80211_get_bss - get a BSS reference + * @wiphy: the wiphy this BSS struct belongs to + * @channel: the channel to search on (or %NULL) + * @bssid: the desired BSSID (or %NULL) + * @ssid: the desired SSID (or %NULL) + * @ssid_len: length of the SSID (or 0) + * @bss_type: type of BSS, see &enum ieee80211_bss_type + * @privacy: privacy filter, see &enum ieee80211_privacy + * @use_for: indicates which use is intended + */ +struct cfg80211_bss *__cfg80211_get_bss(struct wiphy *wiphy, + struct ieee80211_channel *channel, + const u8 *bssid, + const u8 *ssid, size_t ssid_len, + enum ieee80211_bss_type bss_type, + enum ieee80211_privacy privacy, + u32 use_for); + +/** * cfg80211_get_bss - get a BSS reference * @wiphy: the wiphy this BSS struct belongs to * @channel: the channel to search on (or %NULL) @@ -7096,13 +7265,20 @@ cfg80211_inform_bss(struct wiphy *wiphy, * @ssid_len: length of the SSID (or 0) * @bss_type: type of BSS, see &enum ieee80211_bss_type * @privacy: privacy filter, see &enum ieee80211_privacy + * + * This version implies regular usage, %NL80211_BSS_USE_FOR_NORMAL. */ -struct cfg80211_bss *cfg80211_get_bss(struct wiphy *wiphy, - struct ieee80211_channel *channel, - const u8 *bssid, - const u8 *ssid, size_t ssid_len, - enum ieee80211_bss_type bss_type, - enum ieee80211_privacy privacy); +static inline struct cfg80211_bss * +cfg80211_get_bss(struct wiphy *wiphy, struct ieee80211_channel *channel, + const u8 *bssid, const u8 *ssid, size_t ssid_len, + enum ieee80211_bss_type bss_type, + enum ieee80211_privacy privacy) +{ + return __cfg80211_get_bss(wiphy, channel, bssid, ssid, ssid_len, + bss_type, privacy, + NL80211_BSS_USE_FOR_NORMAL); +} + static inline struct cfg80211_bss * cfg80211_get_ibss(struct wiphy *wiphy, struct ieee80211_channel *channel, @@ -7163,19 +7339,6 @@ void cfg80211_bss_iter(struct wiphy *wiphy, void *data), void *iter_data); -static inline enum nl80211_bss_scan_width -cfg80211_chandef_to_scan_width(const struct cfg80211_chan_def *chandef) -{ - switch (chandef->width) { - case NL80211_CHAN_WIDTH_5: - return NL80211_BSS_CHAN_WIDTH_5; - case NL80211_CHAN_WIDTH_10: - return NL80211_BSS_CHAN_WIDTH_10; - default: - return NL80211_BSS_CHAN_WIDTH_20; - } -} - /** * cfg80211_rx_mlme_mgmt - notification of processed MLME management frame * @dev: network device @@ -7208,9 +7371,7 @@ void cfg80211_rx_mlme_mgmt(struct net_device *dev, const u8 *buf, size_t len); void cfg80211_auth_timeout(struct net_device *dev, const u8 *addr); /** - * struct cfg80211_rx_assoc_resp - association response data - * @bss: the BSS that association was requested with, ownership of the pointer - * moves to cfg80211 in the call to cfg80211_rx_assoc_resp() + * struct cfg80211_rx_assoc_resp_data - association response data * @buf: (Re)Association Response frame (header + body) * @len: length of the frame data * @uapsd_queues: bitmap of queues configured for uapsd. Same format @@ -7220,10 +7381,12 @@ void cfg80211_auth_timeout(struct net_device *dev, const u8 *addr); * @ap_mld_addr: AP MLD address (in case of MLO) * @links: per-link information indexed by link ID, use links[0] for * non-MLO connections + * @links.bss: the BSS that association was requested with, ownership of the + * pointer moves to cfg80211 in the call to cfg80211_rx_assoc_resp() * @links.status: Set this (along with a BSS pointer) for links that * were rejected by the AP. */ -struct cfg80211_rx_assoc_resp { +struct cfg80211_rx_assoc_resp_data { const u8 *buf; size_t len; const u8 *req_ies; @@ -7231,7 +7394,7 @@ struct cfg80211_rx_assoc_resp { int uapsd_queues; const u8 *ap_mld_addr; struct { - const u8 *addr; + u8 addr[ETH_ALEN] __aligned(2); struct cfg80211_bss *bss; u16 status; } links[IEEE80211_MLD_MAX_NUM_LINKS]; @@ -7240,7 +7403,7 @@ struct cfg80211_rx_assoc_resp { /** * cfg80211_rx_assoc_resp - notification of processed association response * @dev: network device - * @data: association response data, &struct cfg80211_rx_assoc_resp + * @data: association response data, &struct cfg80211_rx_assoc_resp_data * * After being asked to associate via cfg80211_ops::assoc() the driver must * call either this function or cfg80211_auth_timeout(). @@ -7248,7 +7411,7 @@ struct cfg80211_rx_assoc_resp { * This function may sleep. The caller must hold the corresponding wdev's mutex. */ void cfg80211_rx_assoc_resp(struct net_device *dev, - struct cfg80211_rx_assoc_resp *data); + const struct cfg80211_rx_assoc_resp_data *data); /** * struct cfg80211_assoc_failure - association failure data @@ -7367,7 +7530,7 @@ void cfg80211_notify_new_peer_candidate(struct net_device *dev, * RFkill integration in cfg80211 is almost invisible to drivers, * as cfg80211 automatically registers an rfkill instance for each * wireless device it knows about. Soft kill is also translated - * into disconnecting and turning all interfaces off, drivers are + * into disconnecting and turning all interfaces off. Drivers are * expected to turn off the device when all interfaces are down. * * However, devices may have a hard RFkill line, in which case they @@ -7415,7 +7578,7 @@ static inline void wiphy_rfkill_stop_polling(struct wiphy *wiphy) * the configuration mechanism. * * A driver supporting vendor commands must register them as an array - * in struct wiphy, with handlers for each one, each command has an + * in struct wiphy, with handlers for each one. Each command has an * OUI and sub command ID to identify it. * * Note that this feature should not be (ab)used to implement protocol @@ -7579,7 +7742,7 @@ static inline void cfg80211_vendor_event(struct sk_buff *skb, gfp_t gfp) * interact with driver-specific tools to aid, for instance, * factory programming. * - * This chapter describes how drivers interact with it, for more + * This chapter describes how drivers interact with it. For more * information see the nl80211 book's chapter on it. */ @@ -7967,7 +8130,8 @@ void cfg80211_roamed(struct net_device *dev, struct cfg80211_roam_info *info, * cfg80211_port_authorized - notify cfg80211 of successful security association * * @dev: network device - * @bssid: the BSSID of the AP + * @peer_addr: BSSID of the AP/P2P GO in case of STA/GC or STA/GC MAC address + * in case of AP/P2P GO * @td_bitmap: transition disable policy * @td_bitmap_len: Length of transition disable policy * @gfp: allocation flags @@ -7978,8 +8142,11 @@ void cfg80211_roamed(struct net_device *dev, struct cfg80211_roam_info *info, * should be preceded with a call to cfg80211_connect_result(), * cfg80211_connect_done(), cfg80211_connect_bss() or cfg80211_roamed() to * indicate the 802.11 association. + * This function can also be called by AP/P2P GO driver that supports + * authentication offload. In this case the peer_mac passed is that of + * associated STA/GC. */ -void cfg80211_port_authorized(struct net_device *dev, const u8 *bssid, +void cfg80211_port_authorized(struct net_device *dev, const u8 *peer_addr, const u8* td_bitmap, u8 td_bitmap_len, gfp_t gfp); /** @@ -8568,7 +8735,7 @@ bool cfg80211_reg_can_beacon_relax(struct wiphy *wiphy, * @link_id: the link ID for MLO, must be 0 for non-MLO * @punct_bitmap: the new puncturing bitmap * - * Caller must acquire wdev_lock, therefore must only be called from sleepable + * Caller must hold wiphy mutex, therefore must only be called from sleepable * driver context! */ void cfg80211_ch_switch_notify(struct net_device *dev, @@ -8808,6 +8975,18 @@ static inline size_t ieee80211_ie_split(const u8 *ies, size_t ielen, } /** + * ieee80211_fragment_element - fragment the last element in skb + * @skb: The skbuf that the element was added to + * @len_pos: Pointer to length of the element to fragment + * @frag_id: The element ID to use for fragments + * + * This function fragments all data after @len_pos, adding fragmentation + * elements with the given ID as appropriate. The SKB will grow in size + * accordingly. + */ +void ieee80211_fragment_element(struct sk_buff *skb, u8 *len_pos, u8 frag_id); + +/** * cfg80211_report_wowlan_wakeup - report wakeup from WoWLAN * @wdev: the wireless device reporting the wakeup * @wakeup: the wakeup report @@ -9056,9 +9235,9 @@ bool cfg80211_iftype_allowed(struct wiphy *wiphy, enum nl80211_iftype iftype, /** * cfg80211_assoc_comeback - notification of association that was - * temporarly rejected with a comeback + * temporarily rejected with a comeback * @netdev: network device - * @ap_addr: AP (MLD) address that rejected the assocation + * @ap_addr: AP (MLD) address that rejected the association * @timeout: timeout interval value TUs. * * this function may sleep. the caller must hold the corresponding wdev's mutex. @@ -9222,4 +9401,60 @@ bool cfg80211_valid_disable_subchannel_bitmap(u16 *bitmap, */ void cfg80211_links_removed(struct net_device *dev, u16 link_mask); +/** + * cfg80211_schedule_channels_check - schedule regulatory check if needed + * @wdev: the wireless device to check + * + * In case the device supports NO_IR or DFS relaxations, schedule regulatory + * channels check, as previous concurrent operation conditions may not + * hold anymore. + */ +void cfg80211_schedule_channels_check(struct wireless_dev *wdev); + +#ifdef CONFIG_CFG80211_DEBUGFS +/** + * wiphy_locked_debugfs_read - do a locked read in debugfs + * @wiphy: the wiphy to use + * @file: the file being read + * @buf: the buffer to fill and then read from + * @bufsize: size of the buffer + * @userbuf: the user buffer to copy to + * @count: read count + * @ppos: read position + * @handler: the read handler to call (under wiphy lock) + * @data: additional data to pass to the read handler + */ +ssize_t wiphy_locked_debugfs_read(struct wiphy *wiphy, struct file *file, + char *buf, size_t bufsize, + char __user *userbuf, size_t count, + loff_t *ppos, + ssize_t (*handler)(struct wiphy *wiphy, + struct file *file, + char *buf, + size_t bufsize, + void *data), + void *data); + +/** + * wiphy_locked_debugfs_write - do a locked write in debugfs + * @wiphy: the wiphy to use + * @file: the file being written to + * @buf: the buffer to copy the user data to + * @bufsize: size of the buffer + * @userbuf: the user buffer to copy from + * @count: read count + * @handler: the write handler to call (under wiphy lock) + * @data: additional data to pass to the write handler + */ +ssize_t wiphy_locked_debugfs_write(struct wiphy *wiphy, struct file *file, + char *buf, size_t bufsize, + const char __user *userbuf, size_t count, + ssize_t (*handler)(struct wiphy *wiphy, + struct file *file, + char *buf, + size_t count, + void *data), + void *data); +#endif + #endif /* __NET_CFG80211_H */ |