summaryrefslogtreecommitdiff
path: root/drivers/scsi/hisi_sas
AgeCommit message (Collapse)Author
2026-07-26scsi: libsas: Fix HA resume deadlock and hisi_sas disk-wake raceXingui Yang
Commit fbefe22811c3 ("scsi: libsas: Don't always drain event workqueue for HA resume") introduced sas_resume_ha_no_sync() to avoid a deadlock: the PHYE_RESUME_TIMEOUT handler, running on the HA event workqueue, calls sas_deform_port() -> sas_destruct_devices(), which removes SCSI devices and waits for the host to become runtime-active. But the host cannot resume until sas_resume_ha() -> sas_drain_work() returns, and the drain is blocked on that very handler. However skipping the drain reintroduces a race: hisi_sas returns from resume before all PHY UP work and libsas discovery work finish. The controller may then autosuspend while disks are still waking up. The disks issue IO to a suspended controller, the IO fails, and the disks get disabled. Fix the deadlock at its source by moving the PHYE_RESUME_TIMEOUT notification to after sas_drain_work(). By then the host resume is about to complete, so device removal through device_link no longer blocks on the resume and the cycle is broken. With the deadlock gone, restore sas_resume_ha() (the draining variant) in hisi_sas and remove sas_resume_ha_no_sync(). The reorder is safe for the other libsas consumers (isci, pm8001, aic94xx, mvsas). During suspend, sas_suspend_devices() calls sas_notify_lldd_dev_gone() for each device, which sets dev->lldd_dev to NULL. When scsi_unblock_requests re-enables I/O in resume, any I/O to a timed-out phy's disk is immediately rejected by the LLDD before reaching hardware: isci returns SAS_DEVICE_UNKNOWN (mapped to DID_BAD_TARGET), and pm8001 returns SAS_PHY_DOWN (mapped to DID_NO_CONNECT). Both complete directly via scsi_done() without entering SCSI EH. This is identical in both the old and new ordering since lldd_dev_gone runs during suspend, before resume. The reorder only affects when the PHYE_RESUME_TIMEOUT handler runs (synchronized by sas_drain_work() vs. asynchronous after resume returns), not whether I/O can reach the device. aic94xx and mvsas do not register any PM ops and never reach this code path. Fixes: fbefe22811c3 ("scsi: libsas: Don't always drain event workqueue for HA resume") Signed-off-by: Xingui Yang <yangxingui@huawei.com> Reviewed-by: John Garry <john.g.garry@oracle.com> Link: https://patch.msgid.link/20260716081145.3950172-1-yangxingui@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2026-06-15Merge branch 7.1/scsi-fixes into 7.2/scsi-stagingMartin K. Petersen
Pull in outstanding commits from 7.1 branch. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2026-05-14scsi: hisi_sas: Add slave_destroy interface for v3 hwYihang Li
WARNING is triggered when executing link reset of remote PHY and rmmod SAS driver simultaneously. Following is the WARNING log: WARNING: CPU: 61 PID: 21818 at drivers/base/core.c:1347 __device_links_no_driver+0xb4/0xc0 Call trace: __device_links_no_driver+0xb4/0xc0 device_links_driver_cleanup+0xb0/0xfc __device_release_driver+0x198/0x23c device_release_driver+0x38/0x50 bus_remove_device+0x130/0x140 device_del+0x184/0x434 __scsi_remove_device+0x118/0x150 scsi_remove_target+0x1bc/0x240 sas_rphy_remove+0x90/0x94 sas_rphy_delete+0x24/0x3c sas_destruct_devices+0x64/0xa0 [libsas] sas_revalidate_domain+0xe4/0x150 [libsas] process_one_work+0x1e0/0x46c worker_thread+0x15c/0x464 kthread+0x160/0x170 ret_from_fork+0x10/0x20 ---[ end trace 71e059eb58f85d4a ]--- During SAS phy up, link->status is set to DL_STATE_AVAILABLE in device_links_driver_bound, then this setting influences __device_links_no_driver() before driver rmmod and caused WARNING. Add the slave_destroy interface to make sure link is removed after flush workque. Fixes: 16fd4a7c5917 ("scsi: hisi_sas: Add device link between SCSI devices and hisi_hba") Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://patch.msgid.link/20260425082056.2749910-1-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2026-04-20scsi: hisi_sas: Fix sparse warnings in prep_ata_v3_hw()Yihang Li
In prep_ata_v3_hw(), add cpu_to_le32() to fix warning: drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:1448:26: sparse: sparse: invalid assignment: |= drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:1448:26: sparse: left side has type restricted __le32 drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:1448:26: sparse: right side has type unsigned int Fixes: 8aa580cd9284 ("scsi: hisi_sas: Enable force phy when SATA disk directly connected") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202604191850.IVYPTaML-lkp@intel.com/ Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://patch.msgid.link/20260420021044.3339459-1-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2026-04-02Merge branch 7.0/scsi-fixes into 7.1/scsi-stagingMartin K. Petersen
Pull in fixes to resolve mpi3mr merge conflict. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2026-03-07scsi: hisi_sas: Fix the risk of overflow in bitwise logical operationsYihang Li
Fix a few constants defined via macros that had overflow risks. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://patch.msgid.link/20260305064700.116033-3-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2026-03-07scsi: hisi_sas: Correct printing format issuesYihang Li
There are some print format errors, fix them. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://patch.msgid.link/20260305064700.116033-2-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2026-03-07scsi: hisi_sas: Fix NULL pointer exception during user_scan()Xingui Yang
user_scan() invokes updated sas_user_scan() for channel 0, and if successful, iteratively scans remaining channels (1 to shost->max_channel) via scsi_scan_host_selected() in commit 37c4e72b0651 ("scsi: Fix sas_user_scan() to handle wildcard and multi-channel scans"). However, hisi_sas supports only one channel, and the current value of max_channel is 1. sas_user_scan() for channel 1 will trigger the following NULL pointer exception: [ 441.554662] Unable to handle kernel NULL pointer dereference at virtual address 00000000000008b0 [ 441.554699] Mem abort info: [ 441.554710] ESR = 0x0000000096000004 [ 441.554718] EC = 0x25: DABT (current EL), IL = 32 bits [ 441.554723] SET = 0, FnV = 0 [ 441.554726] EA = 0, S1PTW = 0 [ 441.554730] FSC = 0x04: level 0 translation fault [ 441.554735] Data abort info: [ 441.554737] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 441.554742] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 441.554747] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 441.554752] user pgtable: 4k pages, 48-bit VAs, pgdp=00000828377a6000 [ 441.554757] [00000000000008b0] pgd=0000000000000000, p4d=0000000000000000 [ 441.554769] Internal error: Oops: 0000000096000004 [#1] SMP [ 441.629589] Modules linked in: arm_spe_pmu arm_smmuv3_pmu tpm_tis_spi hisi_uncore_sllc_pmu hisi_uncore_pa_pmu hisi_uncore_l3c_pmu hisi_uncore_hha_pmu hisi_uncore_ddrc_pmu hisi_uncore_cpa_pmu hns3_pmu hisi_ptt hisi_pcie_pmu tpm_tis_core spidev spi_hisi_sfc_v3xx hisi_uncore_pmu spi_dw_mmio fuse hclge hclge_common hisi_sec2 hisi_hpre hisi_zip hisi_qm hns3 hisi_sas_v3_hw sm3_ce sbsa_gwdt hnae3 hisi_sas_main uacce hisi_dma i2c_hisi dm_mirror dm_region_hash dm_log dm_mod [ 441.670819] CPU: 46 UID: 0 PID: 6994 Comm: bash Kdump: loaded Not tainted 7.0.0-rc2+ #84 PREEMPT [ 441.691327] pstate: 81400009 (Nzcv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 441.698277] pc : sas_find_dev_by_rphy+0x44/0x118 [ 441.702896] lr : sas_find_dev_by_rphy+0x3c/0x118 [ 441.707502] sp : ffff80009abbba40 [ 441.710805] x29: ffff80009abbba40 x28: ffff082819a40008 x27: ffff082810c37c08 [ 441.717930] x26: ffff082810c37c28 x25: ffff082819a40290 x24: ffff082810c37c00 [ 441.725054] x23: 0000000000000000 x22: 0000000000000001 x21: ffff082819a40000 [ 441.732179] x20: ffff082819a40290 x19: 0000000000000000 x18: 0000000000000020 [ 441.739304] x17: 0000000000000000 x16: ffffb5dad6bda690 x15: 00000000ffffffff [ 441.746428] x14: ffff082814c3b26c x13: 00000000ffffffff x12: ffff082814c3b26a [ 441.753553] x11: 00000000000000c0 x10: 000000000000003a x9 : ffffb5dad5ea94f4 [ 441.760678] x8 : 000000000000003a x7 : ffff80009abbbab0 x6 : 0000000000000030 [ 441.767802] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 [ 441.774926] x2 : ffff08280f35a300 x1 : ffffb5dad7127180 x0 : 0000000000000000 [ 441.782053] Call trace: [ 441.784488] sas_find_dev_by_rphy+0x44/0x118 (P) [ 441.789095] sas_target_alloc+0x24/0xb0 [ 441.792920] scsi_alloc_target+0x290/0x330 [ 441.797010] __scsi_scan_target+0x88/0x258 [ 441.801096] scsi_scan_channel+0x74/0xb8 [ 441.805008] scsi_scan_host_selected+0x170/0x188 [ 441.809615] sas_user_scan+0xfc/0x148 [ 441.813267] store_scan+0x10c/0x180 [ 441.816743] dev_attr_store+0x20/0x40 [ 441.820398] sysfs_kf_write+0x84/0xa8 [ 441.824054] kernfs_fop_write_iter+0x130/0x1c8 [ 441.828487] vfs_write+0x2c0/0x370 [ 441.831880] ksys_write+0x74/0x118 [ 441.835271] __arm64_sys_write+0x24/0x38 [ 441.839182] invoke_syscall+0x50/0x120 [ 441.842919] el0_svc_common.constprop.0+0xc8/0xf0 [ 441.847611] do_el0_svc+0x24/0x38 [ 441.850913] el0_svc+0x38/0x158 [ 441.854043] el0t_64_sync_handler+0xa0/0xe8 [ 441.858214] el0t_64_sync+0x1ac/0x1b0 [ 441.861865] Code: aa1303e0 97ff70a8 34ffff80 d10a4273 (f9445a75) [ 441.867946] ---[ end trace 0000000000000000 ]--- Therefore, set max_channel to 0. Fixes: e21fe3a52692 ("scsi: hisi_sas: add initialisation for v3 pci-based controller") Signed-off-by: Xingui Yang <yangxingui@huawei.com> Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://patch.msgid.link/20260305064039.4096775-1-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-08-18scsi: hisi_sas: Use dev_parent_is_expander() helperNiklas Cassel
Make use of the dev_parent_is_expander() helper. Signed-off-by: Niklas Cassel <cassel@kernel.org> Link: https://lore.kernel.org/r/20250814173215.1765055-16-cassel@kernel.org Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: John Garry <john.g.garry@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-06-16scsi: Don't use %pK through printk()Thomas Weißschuh
In the past %pK was preferable to %p as it would not leak raw pointer values into the kernel log. Since commit ad67b74d2469 ("printk: hash addresses printed with %p") the regular %p has been improved to avoid this issue. Furthermore, restricted pointers ("%pK") were never meant to be used through printk(). They can still unintentionally leak raw pointers or acquire sleeping locks in atomic contexts. Switch to the regular pointer formatting which is safer and easier to reason about. Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de> Link: https://lore.kernel.org/r/20250611-restricted-pointers-scsi-v1-1-fe31bfbc4910@linutronix.de Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-06-08treewide, timers: Rename from_timer() to timer_container_of()Ingo Molnar
Move this API to the canonical timer_*() namespace. [ tglx: Redone against pre rc1 ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
2025-05-20scsi: hisi_sas: Fix warning detected by sparseYihang Li
LKP reports below warning when building for RISC-V with randconfig configuration. drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:4554:25: sparse: sparse: incorrect type in argument 4 (different base types) @@ expected restricted __le32 [usertype] *[assigned] ptr @@ got unsigned int * @@ Type cast to fix this warning. Fixes: 4ca7fe99fc84 ("scsi: hisi_sas: Use macro instead of magic number") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202505150705.k9ZzMxf1-lkp@intel.com/ Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20250515013504.3234016-1-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-04-28Merge branch '6.15/scsi-fixes' into 6.16/scsi-stagingMartin K. Petersen
Pull in fixes from 6.15 and resolve a few conflicts so we can have a clean base for UFS patches. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-04-21scsi: hisi_sas: Wait until error handling is completeYihang Li
SATA devices are lost when FLR is performed while the controller and disks are in suspended state. This is because the libata layer is called to initialize the SATA device during controller resume. If FLR is executed at this time, the IDENTIFY command fails. As a result, the revalidate fails, and the SATA device is disabled by the libata layer. Wait until error handling completes. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20250414080845.1220997-5-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-04-21scsi: hisi_sas: Call I_T_nexus after soft reset for SATA diskYihang Li
In commit 21c7e972475e ("scsi: hisi_sas: Disable SATA disk phy for severe I_T nexus reset failure"), if the softreset fails upon certain conditions, the PHY connected to the disk is disabled directly. Manual recovery is required, which is inconvenient for users in actual use. In addition, SATA disks do not support simultaneous connection of multiple hosts. Therefore, when multiple controllers are connected to a SATA disk at the same time, the controller which is connected later failed to issue an ATA softreset to the SATA disk. As a result, the PHY associated with the disk is disabled and cannot be automatically recovered. Now that, we will not focus on the execution result of softreset. No matter whether the execution is successful or not, we will directly carry out I_T_nexus_reset. Fixes: 21c7e972475e ("scsi: hisi_sas: Disable SATA disk phy for severe I_T nexus reset failure") Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20250414080845.1220997-4-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-04-21scsi: hisi_sas: Coding style cleanupYihang Li
Remove superfluous blank lines and symbols. Add spaces around operators. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20250414080845.1220997-3-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-04-21scsi: hisi_sas: Use macro instead of magic numberYihang Li
The hisi_sas driver has a large number of magic numbers which makes for unfriendly code reading. Use macro definitions instead. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20250414080845.1220997-2-liyihang9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-04-08Merge branch '6.15/scsi-queue' into 6.15/scsi-fixesMartin K. Petersen
Pull in remaining fixes from 6.15/scsi-queue. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-04-05treewide: Switch/rename to timer_delete[_sync]()Thomas Gleixner
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree over and remove the historical wrapper inlines. Conversion was done with coccinelle plus manual fixups where necessary. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org>
2025-03-20scsi: hisi_sas: Fix I/O errors caused by hardware port ID changesXingui Yang
The hw port ID of phy may change when inserting disks in batches, causing the port ID in hisi_sas_port and itct to be inconsistent with the hardware, resulting in I/O errors. The solution is to set the device state to gone to intercept I/O sent to the device, and then execute linkreset to discard and find the disk to re-update its information. Signed-off-by: Xingui Yang <yangxingui@huawei.com> Link: https://lore.kernel.org/r/20250312095135.3048379-3-yangxingui@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-03-20scsi: hisi_sas: Enable force phy when SATA disk directly connectedXingui Yang
when a SATA disk is directly connected the SAS controller determines the disk to which I/Os are delivered based on the port ID in the DQ entry. When many phys are disconnected and reconnect, the port ID of phys were changed and used by other link, resulting in I/O being sent to incorrect disk. Data inconsistency on the SATA disk may occur during I/O retries using the old port ID. So enable force phy, then force the command to be executed in a certain phy, and if the actual phy ID of the port does not match the phy configured in the command, the chip will stop delivering the I/O to disk. Fixes: ce60689e12dd ("scsi: hisi_sas: add v3 code to send ATA frame") Signed-off-by: Xingui Yang <yangxingui@huawei.com> Link: https://lore.kernel.org/r/20250312095135.3048379-2-yangxingui@huawei.com Reviewed-by: Yihang Li <liyihang9@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-03-17scsi: hisi_sas: Fixed failure to issue vendor specific commandsXingui Yang
At present, we determine the protocol through the cmd type, but other cmd types, such as vendor-specific commands, default to the PIO protocol. This strategy often causes the execution of different vendor-specific commands to fail. In fact, for these commands, a better way is to use the protocol configured by the command's tf to determine its protocol. Fixes: 6f2ff1a1311e ("hisi_sas: add v2 path to send ATA command") Signed-off-by: Xingui Yang <yangxingui@huawei.com> Link: https://lore.kernel.org/r/20250220090011.313848-1-liyihang9@huawei.com Reviewed-by: Yihang Li <liyihang9@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-03-03scsi: hisi_sas: Remove incorrect ACPI_PTR annotationsArnd Bergmann
Building with W=1 shows a warning about sas_v2_acpi_match being unused when CONFIG_OF is disabled: drivers/scsi/hisi_sas/hisi_sas_v2_hw.c:3635:36: error: unused variable 'sas_v2_acpi_match' [-Werror,-Wunused-const-variable] Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20250225163637.4169300-1-arnd@kernel.org Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-01-26Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds
Pull SCSI updates from James Bottomley: "Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr). The major core change is the renaming of the slave_ methods plus a bit of constification. The rest are minor updates and fixes" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (103 commits) scsi: fnic: Propagate SCSI error code from fnic_scsi_drv_init() scsi: fnic: Test for memory allocation failure and return error code scsi: fnic: Return appropriate error code from failure of scsi drv init scsi: fnic: Return appropriate error code for mem alloc failure scsi: fnic: Remove always-true IS_FNIC_FCP_INITIATOR macro scsi: fnic: Fix use of uninitialized value in debug message scsi: fnic: Delete incorrect debugfs error handling scsi: fnic: Remove unnecessary else to fix warning in FDLS FIP scsi: fnic: Remove extern definition from .c files scsi: fnic: Remove unnecessary else and unnecessary break in FDLS scsi: mpi3mr: Fix possible crash when setting up bsg fails scsi: ufs: bsg: Set bsg_queue to NULL after removal scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails scsi: st: Don't set pos_unknown just after device recognition scsi: aic7xxx: Fix build 'aicasm' warning scsi: Revert "scsi: ufs: core: Probe for EXT_IID support" scsi: storvsc: Ratelimit warning logs to prevent VM denial of service scsi: scsi_debug: Constify sdebug_driver_template scsi: documentation: Corrections for struct updates scsi: driver-api: documentation: Change what is added to docbook ...
2025-01-06block: simplify tag allocation policy selectionChristoph Hellwig
Use a plain BLK_MQ_F_* flag to select the round robin tag selection instead of overlaying an enum with just two possible values into the flags space. Doing so allows adding a BLK_MQ_F_MAX sentinel for simplified overflow checking in the messy debugfs helpers. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20250106083531.799976-5-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk>
2024-12-23scsi: replace blk_mq_pci_map_queues with blk_mq_map_hw_queuesDaniel Wagner
Replace all users of blk_mq_pci_map_queues with the more generic blk_mq_map_hw_queues. This in preparation to retire blk_mq_pci_map_queues. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: John Garry <john.g.garry@oracle.com> Signed-off-by: Daniel Wagner <wagi@kernel.org> Link: https://lore.kernel.org/r/20241202-refactor-blk-affinity-helpers-v6-5-27211e9c2cd5@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
2024-12-04scsi: Rename .device_configure() into .sdev_configure()Bart Van Assche
Improve naming consistency with the .sdev_prep() and .sdev_destroy() methods by renaming .device_configure() into .sdev_configure(). Cc: Christoph Hellwig <hch@lst.de> Acked-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20241022180839.2712439-3-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-12-04scsi: Rename .slave_alloc() and .slave_destroy()Bart Van Assche
Rename .slave_alloc() into .sdev_init() and .slave_destroy() into .sdev_destroy(). The new names make it clear that these are actions on SCSI devices. Make this change in the SCSI core, SCSI drivers and also in the ATA drivers. No functionality has been changed. This patch has been created as follows: * Change the text "slave_alloc" into "sdev_init" in all source files except those in drivers/net/ and Documentation/. * Change the text "slave_destroy" into "sdev_destroy" in all source files except those in drivers/net/ and Documentation/. * Rename lpfc_no_slave() into lpfc_no_sdev(). * Manually adjust whitespace where necessary to restore vertical alignment (dc395x driver and include/linux/libata.h). Acked-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20241022180839.2712439-2-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-11-06scsi: Switch back to struct platform_driver::remove()Uwe Kleine-König
After commit 0edb555a65d1 ("platform: Make platform_driver::remove() return void") .remove() is (again) the right callback to implement for platform drivers. Convert all platform drivers below drivers/scsi to use .remove(), with the eventual goal to drop struct platform_driver::remove_new(). As .remove() and .remove_new() have the same prototypes, conversion is done by just changing the structure member name in the driver initializer. On the way do a few whitespace changes to make indention consistent. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Link: https://lore.kernel.org/r/20241028080754.429191-2-u.kleine-koenig@baylibre.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Add latest_dump for the debugfs dumpYihang Li
Before that, after the user triggers the dump, the latest dump information can be viewed in the directory with the maximum number in the dump directory. After this series patch, the driver creates all debugfs directories and files during initialization. Therefore, users cannot know the directory where the latest dump information is stored. So, add latest_dump file to notify users where the latest dump information is stored. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-14-liyihang9@huawei.com Reviewed-by: Xingui Yang <yangxingui@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Create all dump files during debugfs initializationYihang Li
For the current debugfs of hisi_sas, after user triggers dump, the driver allocate memory space to save the register information and create debugfs files to display the saved information. In this process, the debugfs files created after each dump. Therefore, when the dump is triggered while the driver is unbind, the following hang occurs: [67840.853907] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a0 [67840.862947] Mem abort info: [67840.865855] ESR = 0x0000000096000004 [67840.869713] EC = 0x25: DABT (current EL), IL = 32 bits [67840.875125] SET = 0, FnV = 0 [67840.878291] EA = 0, S1PTW = 0 [67840.881545] FSC = 0x04: level 0 translation fault [67840.886528] Data abort info: [67840.889524] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [67840.895117] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [67840.900284] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [67840.905709] user pgtable: 4k pages, 48-bit VAs, pgdp=0000002803a1f000 [67840.912263] [00000000000000a0] pgd=0000000000000000, p4d=0000000000000000 [67840.919177] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP [67840.996435] pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [67841.003628] pc : down_write+0x30/0x98 [67841.007546] lr : start_creating.part.0+0x60/0x198 [67841.012495] sp : ffff8000b979ba20 [67841.016046] x29: ffff8000b979ba20 x28: 0000000000000010 x27: 0000000000024b40 [67841.023412] x26: 0000000000000012 x25: ffff20202b355ae8 x24: ffff20202b35a8c8 [67841.030779] x23: ffffa36877928208 x22: ffffa368b4972240 x21: ffff8000b979bb18 [67841.038147] x20: ffff00281dc1e3c0 x19: fffffffffffffffe x18: 0000000000000020 [67841.045515] x17: 0000000000000000 x16: ffffa368b128a530 x15: ffffffffffffffff [67841.052888] x14: ffff8000b979bc18 x13: ffffffffffffffff x12: ffff8000b979bb18 [67841.060263] x11: 0000000000000000 x10: 0000000000000000 x9 : ffffa368b1289b18 [67841.067640] x8 : 0000000000000012 x7 : 0000000000000000 x6 : 00000000000003a9 [67841.075014] x5 : 0000000000000000 x4 : ffff002818c5cb00 x3 : 0000000000000001 [67841.082388] x2 : 0000000000000000 x1 : ffff002818c5cb00 x0 : 00000000000000a0 [67841.089759] Call trace: [67841.092456] down_write+0x30/0x98 [67841.096017] start_creating.part.0+0x60/0x198 [67841.100613] debugfs_create_dir+0x48/0x1f8 [67841.104950] debugfs_create_files_v3_hw+0x88/0x348 [hisi_sas_v3_hw] [67841.111447] debugfs_snapshot_regs_v3_hw+0x708/0x798 [hisi_sas_v3_hw] [67841.118111] debugfs_trigger_dump_v3_hw_write+0x9c/0x120 [hisi_sas_v3_hw] [67841.125115] full_proxy_write+0x68/0xc8 [67841.129175] vfs_write+0xd8/0x3f0 [67841.132708] ksys_write+0x70/0x108 [67841.136317] __arm64_sys_write+0x24/0x38 [67841.140440] invoke_syscall+0x50/0x128 [67841.144385] el0_svc_common.constprop.0+0xc8/0xf0 [67841.149273] do_el0_svc+0x24/0x38 [67841.152773] el0_svc+0x38/0xd8 [67841.156009] el0t_64_sync_handler+0xc0/0xc8 [67841.160361] el0t_64_sync+0x1a4/0x1a8 [67841.164189] Code: b9000882 d2800002 d2800023 f9800011 (c85ffc05) [67841.170443] ---[ end trace 0000000000000000 ]--- To fix this issue, create all directories and files during debugfs initialization. In this way, the driver only needs to allocate memory space to save information each time the user triggers dumping. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-13-liyihang9@huawei.com Reviewed-by: Xingui Yang <yangxingui@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Update v3 hw STP_LINK_TIMER settingXingui Yang
At present, it is found that some SATA HDD disks may continue to return the HOLD primitive for more than 500ms when they are busy writing data, which is more likely to trigger an STP link timeout exception. Now Modify STP link timer from 500ms to the maximum value of 1.048575s. Signed-off-by: Xingui Yang <yangxingui@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-12-liyihang9@huawei.com Reviewed-by: Yihang Li <liyihang9@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Add time interval between two H2D FIS following soft reset specXingui Yang
Spec says at least 5us between two H2D FIS when do soft reset, but be generous and sleep for about 1ms. Signed-off-by: Xingui Yang <yangxingui@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-11-liyihang9@huawei.com Reviewed-by: Yihang Li <liyihang9@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Update disk locked timeout to 7 secondsXingui Yang
The SATA disk will be locked after the disk sends the DMA Setup frame until all data frame transmission is completed. The CFG_ICT_TIMER_STEP_TRSH register is used for sata disk to configure the step size of the timer which records the time when the disk is locked. The unit is 1us and the default step size is 150ms. If the disk is locked for more than 7 timer steps, the io to be sent to the disk will end abnormally. The current timeout is only about 1 second, it is easy to trigger IO abnormal end when the SATA hard disk returns data slowly. Adjust the timeout to 7 seconds based on ERC time of most disks. Signed-off-by: Xingui Yang <yangxingui@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-10-liyihang9@huawei.com Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Yihang Li <liyihang9@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Default enable interrupt coalescingYihang Li
In the current interrupt reporting mode, each CQ entry reports an interrupt. However, when there are a large number of I/O hardware completion interrupts, the following issue may occur: [ 4682.678657][ C129] irq 134: nobody cared (try booting with the "irqpoll" option) [ 4682.708455][ C129] Call trace: [ 4682.711589][ C129] dump_backtrace+0x0/0x1e4 [ 4682.715934][ C129] show_stack+0x20/0x2c [ 4682.719933][ C129] dump_stack+0xd8/0x140 [ 4682.724017][ C129] __report_bad_irq+0x54/0x180 [ 4682.728625][ C129] note_interrupt+0x1ec/0x2f0 [ 4682.733143][ C129] handle_irq_event+0x118/0x1ac [ 4682.737834][ C129] handle_fasteoi_irq+0xc8/0x200 [ 4682.742613][ C129] __handle_domain_irq+0x84/0xf0 [ 4682.747391][ C129] gic_handle_irq+0x88/0x2c0 [ 4682.751822][ C129] el1_irq+0xbc/0x140 [ 4682.755648][ C129] _find_next_bit.constprop.0+0x20/0x94 [ 4682.761036][ C129] cpumask_next+0x24/0x30 [ 4682.765208][ C129] gic_ipi_send_mask+0x48/0x170 [ 4682.769900][ C129] __ipi_send_mask+0x34/0x110 [ 4682.775720][ C129] smp_cross_call+0x3c/0xcc [ 4682.780064][ C129] arch_send_call_function_single_ipi+0x38/0x44 [ 4682.786146][ C129] send_call_function_single_ipi+0xd0/0xe0 [ 4682.791794][ C129] generic_exec_single+0xb4/0x170 [ 4682.796659][ C129] smp_call_function_single_async+0x2c/0x40 [ 4682.802395][ C129] blk_mq_complete_request_remote.part.0+0xec/0x100 [ 4682.808822][ C129] blk_mq_complete_request+0x30/0x70 [ 4682.813950][ C129] scsi_mq_done+0x48/0xac [ 4682.818128][ C129] sas_scsi_task_done+0xb0/0x150 [libsas] [ 4682.823692][ C129] slot_complete_v3_hw+0x230/0x710 [hisi_sas_v3_hw] [ 4682.830120][ C129] cq_thread_v3_hw+0xbc/0x190 [hisi_sas_v3_hw] [ 4682.836114][ C129] irq_thread_fn+0x34/0xa4 [ 4682.840371][ C129] irq_thread+0xc4/0x130 [ 4682.844455][ C129] kthread+0x108/0x13c [ 4682.848365][ C129] ret_from_fork+0x10/0x18 [ 4682.852621][ C129] handlers: [ 4682.855577][ C129] [<00000000949e52bf>] cq_interrupt_v3_hw [hisi_sas_v3_hw] threaded [<000000005d8e3b68>] cq_thread_v3_hw [hisi_sas_v3_hw] [ 4682.868084][ C129] Disabling IRQ #134 When the IRQ management layer processes each hardware interrupt, if the return value of the interrupt handler is IRQ_WAKE_THREAD, it will wake up the handler thread for this interrupt action and set IRQTF_RUNTHREAD flag, wait for the interrupt handling thread to clear the IRQTF_RUNTHREAD flag after execution. Later in note_interrupt(), use irq_count to count hardware interrupts and irqs_unhandled to count interrupts for which no thread handler is responsible. When irq_count reaches 100000 and irqs_unhandled reaches 99000, irq will be disabled. In the performance test scenario, I/O completion hardware interrupts are continuously and quickly generated. As a result, the interrupt processing thread is cyclically called in irq_thread() and does not exit, this affects the response of the interrupt thread to the hardware interrupt and causes irqs_unhandled to grow to 99000. Finally, the irq is disabled. Therefore, default enable interrupt coalescing to reduce the generation of hardware interrupts, this helps interrupt processing threads to stop calling in irq_thread(). For interrupt coalescing, according to the actual performance test, set the count of CQ entries to 10 and the interrupt coalescing timeout period to 10us based on the actual performance test. Before and after interrupt coalescing is enabled, the 4K read/write performance is improved by about 3%, and the 256K read/write performance is basically the same. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-9-liyihang9@huawei.com Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Add cond_resched() for no forced preemption modelYihang Li
For no forced preemption model kernel, in the scenario where the expander is connected to 12 high performance SAS SSDs, the following call trace may occur: [ 214.409199][ C240] watchdog: BUG: soft lockup - CPU#240 stuck for 22s! [irq/149-hisi_sa:3211] [ 214.568533][ C240] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--) [ 214.575224][ C240] pc : fput_many+0x8c/0xdc [ 214.579480][ C240] lr : fput+0x1c/0xf0 [ 214.583302][ C240] sp : ffff80002de2b900 [ 214.587298][ C240] x29: ffff80002de2b900 x28: ffff1082aa412000 [ 214.593291][ C240] x27: ffff3062a0348c08 x26: ffff80003a9f6000 [ 214.599284][ C240] x25: ffff1062bbac5c40 x24: 0000000000001000 [ 214.605277][ C240] x23: 000000000000000a x22: 0000000000000001 [ 214.611270][ C240] x21: 0000000000001000 x20: 0000000000000000 [ 214.617262][ C240] x19: ffff3062a41ae580 x18: 0000000000010000 [ 214.623255][ C240] x17: 0000000000000001 x16: ffffdb3a6efe5fc0 [ 214.629248][ C240] x15: ffffffffffffffff x14: 0000000003ffffff [ 214.635241][ C240] x13: 000000000000ffff x12: 000000000000029c [ 214.641234][ C240] x11: 0000000000000006 x10: ffff80003a9f7fd0 [ 214.647226][ C240] x9 : ffffdb3a6f0482fc x8 : 0000000000000001 [ 214.653219][ C240] x7 : 0000000000000002 x6 : 0000000000000080 [ 214.659212][ C240] x5 : ffff55480ee9b000 x4 : fffffde7f94c6554 [ 214.665205][ C240] x3 : 0000000000000002 x2 : 0000000000000020 [ 214.671198][ C240] x1 : 0000000000000021 x0 : ffff3062a41ae5b8 [ 214.677191][ C240] Call trace: [ 214.680320][ C240] fput_many+0x8c/0xdc [ 214.684230][ C240] fput+0x1c/0xf0 [ 214.687707][ C240] aio_complete_rw+0xd8/0x1fc [ 214.692225][ C240] blkdev_bio_end_io+0x98/0x140 [ 214.696917][ C240] bio_endio+0x160/0x1bc [ 214.701001][ C240] blk_update_request+0x1c8/0x3bc [ 214.705867][ C240] scsi_end_request+0x3c/0x1f0 [ 214.710471][ C240] scsi_io_completion+0x7c/0x1a0 [ 214.715249][ C240] scsi_finish_command+0x104/0x140 [ 214.720200][ C240] scsi_softirq_done+0x90/0x180 [ 214.724892][ C240] blk_mq_complete_request+0x5c/0x70 [ 214.730016][ C240] scsi_mq_done+0x48/0xac [ 214.734194][ C240] sas_scsi_task_done+0xbc/0x16c [libsas] [ 214.739758][ C240] slot_complete_v3_hw+0x260/0x760 [hisi_sas_v3_hw] [ 214.746185][ C240] cq_thread_v3_hw+0xbc/0x190 [hisi_sas_v3_hw] [ 214.752179][ C240] irq_thread_fn+0x34/0xa4 [ 214.756435][ C240] irq_thread+0xc4/0x130 [ 214.760520][ C240] kthread+0x108/0x13c [ 214.764430][ C240] ret_from_fork+0x10/0x18 This is because in the hisi_sas driver, both the hardware interrupt handler and the interrupt thread are executed on the same CPU. In the performance test scenario, function irq_wait_for_interrupt() will always return 0 if lots of interrupts occurs and the CPU will be continuously consumed. As a result, the CPU cannot run the watchdog thread. When the watchdog time exceeds the specified time, call trace occurs. To fix it, add cond_resched() to execute the watchdog thread. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-8-liyihang9@huawei.com Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Check usage count only when the runtime PM status is ↵Yihang Li
RPM_SUSPENDING Users can suspend the machine with 'echo disk > /sys/power/state', but the suspend will fail because the SAS controller cannot be suspended: [root@localhost ~]# echo freeze > /sys/power/state -bash: echo: write error: Device or resource busy [15104.142955] PM: suspend entry (s2idle) ... [15104.283465] hisi_sas_v3_hw 0000:32:04.0: entering suspend state [15104.283480] hisi_sas_v3_hw 0000:30:04.0: entering suspend state [15104.283500] hisi_sas_v3_hw 0000:32:04.0: PM suspend: host status cannot be suspended [15104.283508] hisi_sas_v3_hw 0000:30:04.0: PM suspend: host status cannot be suspended [15104.283516] hisi_sas_v3_hw 0000:32:04.0: PM: pci_pm_suspend(): suspend_v3_hw+0x0/0x210 [hisi_sas_v3_hw] returns -16 [15104.283527] hisi_sas_v3_hw 0000:32:04.0: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x1c0 returns -16 [15104.283524] hisi_sas_v3_hw 0000:30:04.0: PM: pci_pm_suspend(): suspend_v3_hw+0x0/0x210 [hisi_sas_v3_hw] returns -16 [15104.283533] hisi_sas_v3_hw 0000:32:04.0: PM: failed to suspend async: error -16 [15104.283536] hisi_sas_v3_hw 0000:30:04.0: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x1c0 returns -16 [15104.283542] hisi_sas_v3_hw 0000:30:04.0: PM: failed to suspend async: error -16 The problem is that when the ->runtime_suspend() callback suspend_v3_hw() is executing, the current runtime PM status is RPM_ACTIVE and the usage count of the controller is not 0, so return immediately. To fix it, Check the device usage count only when the runtime PM status is RPM_SUSPENDING. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-7-liyihang9@huawei.com Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Reset PHY again if phyup timeoutYihang Li
In commit 89954f024c3a ("scsi: hisi_sas: Ensure all enabled PHYs up during controller reset"), we enable PHYs in parallel through async operations and wait for PHYs come up. However, for some directly attached SATA disks, the PHY not come up after a timeout period and the hardware is not ready. At this time, we should get the latest PHY hardware state, if the new PHY state is not ready but the old PHY state is ready, call work HISI_PHYE_LINK_RESET to give it another chance to phyup. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-6-liyihang9@huawei.com Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Enable all PHYs that are not disabled by user during ↵Yihang Li
controller reset For the controller reset operation(such as FLR or clear nexus ha in SCSI EH), we will disable all PHYs and then enable PHY based on the hisi_hba->phy_state obtained in hisi_sas_controller_reset_prepare(). If the device is removed before controller reset or the PHY is not attached to any device in directly attached scenario, the corresponding bit of phy_state is not set. After controller reset done, the PHY is disabled. The device cannot be identified even if user reconnect the disk. Therefore, for PHYs that are not disabled by user, hisi_sas_phy_enable() needs to be executed even if the corresponding bit of phy_state is not set. Fixes: 89954f024c3a ("scsi: hisi_sas: Ensure all enabled PHYs up during controller reset") Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-5-liyihang9@huawei.com Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Add firmware information checkYihang Li
For security purposes, after information is obtained through the FW, check information to ensure data correctness. - In v1 and v2 hw, the maximum number of PHYs is 9, while in v3 it is 8. - In v2 and v3 hw, the maximum number of hardware queues is 16, while in v1 it is 32. Also add some debug logs for failure. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-4-liyihang9@huawei.com Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Create trigger_dump at the end of the debugfs initializationYihang Li
In the current debugfs initialization process, the interface trigger_dump is created first, and then the dump directory is created to store the register dump information. The issue is that after the trigger_dump interface is created, users can access the interface to trigger dump and call debugfs_create_files_v3_hw(). In debugfs_create_files_v3_hw(), if .debugfs_dump_dentry is NULL, the file for storing dump information is created under /sys/kernel/debug, and the memory and information cannot be released after the driver is uninstalled. Therefore, the creation of the trigger_dump interface is placed at the end of debugfs initialization. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-3-liyihang9@huawei.com Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-15scsi: hisi_sas: Adjust priority of registering and exiting debugfs for securityYihang Li
To be safe, we should register debugfs at the last stage of driver initialization and then unregister debugfs at the first stage of driver uninstallation. Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20241008021822.2617339-2-liyihang9@huawei.com Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-09-12scsi: hisi_sas: Remove trailing space after \n newlineColin Ian King
There is a extraneous space after a newline in a dev_info message. Remove it. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20240902144153.309920-1-colin.i.king@gmail.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-08-22scsi: Expand all create*_workqueue() invocationsBart Van Assche
The workqueue maintainer wants to remove the create*_workqueue() macros because these macros always set the WQ_MEM_RECLAIM flag and because these only support literal workqueue names. Hence this patch that replaces the create*_workqueue() invocations with the definition of this macro. The WQ_MEM_RECLAIM flag has been retained because I think that flag is necessary for workqueues created by storage drivers. This patch has been generated by running spatch and git clang-format. spatch has been invoked as follows: spatch --in-place --sp-file expand-create-workqueue.spatch $(git grep -lEw 'create_(freezable_|singlethread_|)workqueue' */scsi */ufs) The contents of the expand-create-workqueue.spatch file is as follows: @@ expression name; @@ -create_workqueue(name) +alloc_workqueue("%s", WQ_MEM_RECLAIM, 1, name) @@ expression name; @@ -create_freezable_workqueue(name) +alloc_workqueue("%s", WQ_FREEZABLE | WQ_UNBOUND | WQ_MEM_RECLAIM, 1, name) @@ expression name; @@ -create_singlethread_workqueue(name) +alloc_ordered_workqueue("%s", WQ_MEM_RECLAIM, name) Reviewed-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240822195944.654691-2-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-05-14Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds
Pull SCSI updates from James Bottomley: "Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas). The major update (which causes a conflict with block, see below) is Christoph removing the queue limits and their associated block helpers. The remaining patches are assorted minor fixes and deprecated function updates plus a bit of constification" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits) scsi: mpi3mr: Sanitise num_phys scsi: lpfc: Copyright updates for 14.4.0.2 patches scsi: lpfc: Update lpfc version to 14.4.0.2 scsi: lpfc: Add support for 32 byte CDBs scsi: lpfc: Change lpfc_hba hba_flag member into a bitmask scsi: lpfc: Introduce rrq_list_lock to protect active_rrq_list scsi: lpfc: Clear deferred RSCN processing flag when driver is unloading scsi: lpfc: Update logging of protection type for T10 DIF I/O scsi: lpfc: Change default logging level for unsolicited CT MIB commands scsi: target: Remove unused list 'device_list' scsi: iscsi: Remove unused list 'connlist_err' scsi: ufs: exynos: Add support for Tensor gs101 SoC scsi: ufs: exynos: Add some pa_dbg_ register offsets into drvdata scsi: ufs: exynos: Allow max frequencies up to 267Mhz scsi: ufs: exynos: Add EXYNOS_UFS_OPT_TIMER_TICK_SELECT option scsi: ufs: exynos: Add EXYNOS_UFS_OPT_UFSPR_SECURE option scsi: ufs: dt-bindings: exynos: Add gs101 compatible scsi: qla2xxx: Fix debugfs output for fw_resource_count scsi: qedf: Ensure the copied buf is NUL terminated scsi: bfa: Ensure the copied buf is NUL terminated ...
2024-04-11scsi: libata: Switch to using ->device_configureChristoph Hellwig
Switch to the ->device_configure method instead of ->slave_configure and update the block limits on the passed in queue_limits instead of using the per-limit accessors. Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20240409143748.980206-21-hch@lst.de Reviewed-by: John Garry <john.g.garry@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Acked-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-04-05scsi: hisi_sas: Modify the deadline for ata_wait_after_reset()Xiang Chen
We found that the second parameter of function ata_wait_after_reset() is incorrectly used. We call smp_ata_check_ready_type() to poll the device type until the 30s timeout, so the correct deadline should be (jiffies + 30000). Fixes: 3c2673a09cf1 ("scsi: hisi_sas: Fix SATA devices missing issue during I_T nexus reset") Co-developed-by: xiabing <xiabing12@h-partners.com> Signed-off-by: xiabing <xiabing12@h-partners.com> Co-developed-by: Yihang Li <liyihang9@huawei.com> Signed-off-by: Yihang Li <liyihang9@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Link: https://lore.kernel.org/r/20240402035513.2024241-3-chenxiang66@hisilicon.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-04-05scsi: hisi_sas: Handle the NCQ error returned by D2H frameXiang Chen
We find that some disks use D2H frame instead of SDB frame to return NCQ error. Currently, only the I/O corresponding to the D2H frame is processed in this scenario, which does not meet the processing requirements of the NCQ error scenario. So we set dev_status to HISI_SAS_DEV_NCQ_ERR and abort all I/Os of the disk in this scenario. Co-developed-by: Xingui Yang <yangxingui@huawei.com> Signed-off-by: Xingui Yang <yangxingui@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Link: https://lore.kernel.org/r/20240402035513.2024241-2-chenxiang66@hisilicon.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-03-25Merge patch series "Add LIBSAS_SHT_BASE for libsas"Martin K. Petersen
John Garry <john.g.garry@oracle.com> says: There is much duplication in the scsi_host_template structure for the drivers which use libsas. Similar to how a standard template is used in libata with __ATA_BASE_SHT, create a standard template in LIBSAS_SHT_BASE. Link: https://lore.kernel.org/r/20240308114339.1340549-1-john.g.garry@oracle.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-03-25scsi: hisi_sas: Use LIBSAS_SHT_BASE_NO_SLAVE_INITJohn Garry
Use standard template for scsi_host_template structure to reduce duplication. Reviewed-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20240308114339.1340549-4-john.g.garry@oracle.com Reviewed-by: Igor Pylypiv <ipylypiv@google.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
generated by cgit v1.2.3 (git 2.0.4) at 2026-10-09 20:02:46 +0000