| Age | Commit message (Collapse) | Author |
|---|
|
Currently, the S1G channelisation implementation differs from that of
VHT, which is the PHY that S1G is based on. The major difference between
the clock rate is 1/10th of VHT. However how their channelisation is
represented within cfg80211 and mac80211 vastly differ.
To rectify this, remove the use of IEEE80211_CHAN_1/2/4.. flags that were
previously used to indicate the control channel width, however it should be
implied that the control channels are 1MHz in the case of S1G. Additionally,
introduce the invert - being IEEE80211_CHAN_NO_4/8/16MHz - that imply
the control channel may not be used for a certain bandwidth. With these
new flags, we can perform regulatory and chandef validation just as we would
for VHT.
To deal with the notion that S1G PHYs may contain a 2MHz primary channel,
introduce a new variable, s1g_primary_2mhz, which indicates whether we are
operating on a 2MHz primary channel. In this case, the chandef::chan points to
the 1MHz primary channel pointed to by the primary channel location. Alongside
this, introduce some new helper routines that can extract the sibling 1MHz
channel. The sibling being the alternate 1MHz primary subchannel within the
2MHz primary channel that is not pointed to by chandef::chan.
Furthermore, due to unique restrictions imposed on S1G PHYs, introduce
a new flag, IEEE80211_CHAN_S1G_NO_PRIMARY, which states that the 1MHz channel
cannot be used as a primary channel. This is assumed to be set by vendors
as it is hardware and regdom specific, When we validate a 2MHz primary channel,
we need to ensure both 1MHz subchannels do not contain this flag. If one or
both of the 1MHz subchannels contain this flag then the 2MHz primary is not
permitted for use as a primary channel.
Properly integrate S1G channel validation such that it is implemented
according with other PHY types such as VHT. Additionally, implement a new
S1G-specific regulatory flag to allow cfg80211 to understand specific
vendor requirements for S1G PHYs.
Signed-off-by: Arien Judge <arien.judge@morsemicro.com>
Signed-off-by: Andrew Pope <andrew.pope@morsemicro.com>
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250918051913.500781-2-lachlan.hodges@morsemicro.com
[remove redundant NL80211_ATTR_S1G_PRIMARY_2MHZ check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add better break down for NAN capabilities, as NAN has multiple optional
features. This allows to better indicate which features are supported or
or offloaded to the device.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250908140015.bb02cd8c1596.I01fb2e8dc3662b847f3c27117bc4e199fc96d0a3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The drivers should notify upper layers and user space when a NAN device
joins a cluster. This is needed, for example, to set the correct addr3
in SDF frames. Add API to report cluster join event.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250908140015.ad27b7b6e4d9.I70b213a2a49f18d1ba2ad325e67e8eff51cc7a1f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This notification will be used by the device to inform user space
about upcoming DW. When received, user space will be able to prepare
multicast Service Discovery Frames (SDFs) to be transmitted during the
next DW using %NL80211_CMD_FRAME command on the NAN management interface.
The device/driver will take care to transmit the frames in the correct
timing. This allows to implement a synchronized Discovery Engine (DE)
in user space, if the device doesn't support DE offload.
Note that this notification can be sent before the actual DW starts as
long as the driver/device handles the actual timing of the SDF
transmission.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250908140015.0e1d15031bab.I5b1721e61b63910452b3c5cdcdc1e94cb094d4c9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Current NAN APIs have only basic configuration for master
preference and operating bands. Add and parse additional parameters
which provide more control over NAN synchronization. The newly added
attributes allow to publish additional NAN attributes and vendor
elements in NAN beacons, control scan and discovery beacons
periodicity, enable/disable DW notifications etc.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
tested: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250908140015.a4779492bf8e.I375feb919bd72358173766b9fe10010c40796b33@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Assure user-space only modifies attributes for NL80211_CMD_SET_BSS
that are supported by the driver. This stricter checking is only done
when user-space commits to it by including NL80211_ATTR_BSS_PARAM.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250817190435.1495094-4-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The so-called fullmac devices rely on firmware functionality and/or API to
change BSS parameters. Today there are limited drivers supporting the
nl80211 primitive, but they only handle a subset of the bss parameters
passed if any. The mac80211 driver does handle all parameters and stores
their configured values. Some of the BSS parameters were already conditional
by wiphy->features. For these the wiphy->bss_param_support and wiphy->features
fields are silently aligned in wiphy_register(). Maybe better to issue a warning
instead when they are misaligned.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250817190435.1495094-2-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add new attributes to support EHT MCS/NSS Tx rates and EHT GI/LTF.
Parse EHT fixed MCS/NSS Tx rates and EHT GI/LTF values passed by the
userspace, validate and add as part of cfg80211_bitrate_mask.
MCS mask is constructed by new function, eht_build_mcs_mask(). Max NSS
supported for MCS rates of 7, 9, 11 and 13 is utilized to set MCS
bitmask for each NSS. MCS rates 14, and 15 if supported, are set only
for NSS = 0.
Co-developed-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Link: https://patch.msgid.link/20250815213011.2704803-1-muna.sinada@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
An S1G TIM PVB is encoded differently compared to a non-s1g TIM PVB.
As the AP dictates which encoding mode it uses, here we only implement
block bitmap encoding. This is the default encoding mode used by
all current vendor implementations.
Additionally, S1G has a maximum AID count of 8192, however we are
limiting the current implementation to 1600. This has no resemblence
to the standard and is purely an implementation detail. The reason for
this is due to the TIM elements maximum length of 255. This allows for,
at most, 25 encoded blocks for a PVB encoded with block bitmap. Support
for the maximum of 8192 AIDs will require an implementation of page slicing
to be added to mac80211.
As a result, we perform extra validation on both the STA and AP side
when receiving an AID as an S1G interface.
Add support for block bitmap encoding for an S1G AP and limit the
maximum AID count to 1600 for the current mac80211 implementations.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250725132221.258217-2-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
S1G short beacons are an optional frame type used in an S1G BSS
that contain a limited set of elements. While they are optional,
they are a fundamental part of S1G that enables significant
power saving.
Expose 2 additional netlink attributes,
NL80211_ATTR_S1G_LONG_BEACON_PERIOD which denotes the number of beacon
intervals between each long beacon and NL80211_ATTR_S1G_SHORT_BEACON
which is a nested attribute containing the short beacon tail and
head. We split them as the long beacon period cannot be updated,
and is only used when initialisng the interface, whereas the short
beacon data can be used to both initialise and update the templates.
This follows how things such as the beacon interval and DTIM period
currently operate.
During the initialisation path, we ensure we have the long beacon
period if the short beacon data is being passed down, whereas
the update path will simply update the template if its sent down.
The short beacon data is validated using the same routines for regular
beacons as they support correctly parsing the short beacon format
while ensuring the frame is well-formed.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-2-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case of multi-radio wiphys, with per-radio RTS threshold brought
into use, RTS threshold for each radio in a wiphy can be recorded in
wiphy parameter - wiphy_radio_cfg, as an array. Add a new attribute -
NL80211_WIPHY_RADIO_ATTR_RTS_THRESHOLD in nested parameter -
NL80211_ATTR_WIPHY_RADIOS. When a request for getting RTS threshold
for a particular radio is received, parse the radio id and get the
required data. Add this data to the newly added nested attribute
NL80211_WIPHY_RADIO_ATTR_RTS_THRESHOLD. Add support to report this
data to userspace.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-4-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
driver
In the case of SME-in-driver, the driver can internally choose to
update the links based on the AP MLD recommendation and do link
reconfiguration negotiation with AP MLD.
(e.g., After the driver processing the BSS Transition Management request
frame received from the AP MLD with Neighbor Report containing
Multi-Link element with recommended links information chooses to do link
reconfiguration negotiation with AP MLD).
To support this, extend cfg80211_mlo_reconf_add_done() and
NL80211_CMD_ASSOC_MLO_RECONF to indicate added links information for
driver-initiated link reconfiguration requests. For removed links,
the driver indicates links information using the
NL80211_CMD_LINKS_REMOVED event for driver-initiated cases, the same as
supplicant initiated cases.
For the driver-initiated case, cfg80211 will receive link
reconfiguration result asynchronously from driver so holding BSSes of
the accepted add links is needed in the event path. Also, no need of
unhold call for the rejected add link BSSes since there was no hold call
happened previously.
Once the supplicant receives the NL80211_CMD_ASSOC_MLO_RECONF event,
it needs to process the information about newly added links and install
per-link group keys (e.g., GTK/IGTK/BIGTK etc.).
In case of the SME-in-driver, using a vendor interface etc. to notify
the supplicant to initiate a link reconfiguration request and then
supplicant sending command to the cfg80211 can lead to race conditions.
The correct design to avoid this is that the driver indicates the
cfg80211 directly with the results of the link reconfiguration
negotiation.
Signed-off-by: Kavita Kavita <quic_kkavita@quicinc.com>
Link: https://patch.msgid.link/20250604105757.2542-3-quic_kkavita@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The existing documentation for the NL80211_CMD_ASSOC_MLO_RECONF
does not clearly explain handling of link reconfiguration request
results from the driver.
Add documentation to explain that the command is used as an event to
notify userspace about added links information, and that the existing
NL80211_CMD_LINKS_REMOVED command is used to notify userspace about
removed links information.
Signed-off-by: Kavita Kavita <quic_kkavita@quicinc.com>
Link: https://patch.msgid.link/20250604105757.2542-2-quic_kkavita@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
During non-transmitted (nontx) profile configuration, interface
index of the transmitted (tx) profile is used to retrieve the
wireless device (wdev) associated with it. With MLO, this 'wdev'
may be part of an MLD with more than one link, hence only
interface index is not sufficient anymore to retrieve the correct
tx profile. Add a new attribute to configure link id of tx profile.
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Co-developed-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Co-developed-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408184501.3715887-2-aloka.dixit@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Improve the documentation for supported BSS selectors to make it more
precise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.ba402ff47314.I502b56111b62ea0be174ae76bd03684ae1d4aefb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some regulatory bodies doesn't allow IR (initiate radioation) on a
specific subband, but allows it for channels with a bandwidth of 20 MHz.
Add a channel flag that indicates that, and consider it in
cfg80211_reg_check_beaconing.
While on it, fix the kernel doc of enum nl80211_reg_rule_flags and
change it to use BIT().
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Co-developed-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Signed-off-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.d3ab352a73ff.I8a8f79e1c9eb74936929463960ee2a324712fe51@changeid
[fix typo]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some extended MLD capabilities and operations bits (currently
the "BTM MLD Recommendataion For Multiple APs Support" bit)
may depend on userspace capabilities. Allow userspace to pass
the values for this field that it supports to the association
and link reconfiguration operations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://patch.msgid.link/20250308225541.bd52078b5f65.I4dd8f53b0030db7ea87a2e0920989e7e2c7b5345@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Unconditionally start to refuse creating cooked monitor interfaces to
phase them out.
There is no feature flag for drivers to opt-in for cooked monitor and
all known users are using/preferring the modern API since the hostapd
release 1.0 in May 2012.
Signed-off-by: Alexander Wetzel <Alexander@wetzel-home.de>
Link: https://patch.msgid.link/20250204111352.7004-1-Alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for configuring Emergency Preparedness Communication
Services (EPCS) for station mode.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250102161730.ea54ac94445c.I11d750188bc0871e13e86146a3b5cc048d853e69@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for requesting dynamic addition/removal of links to the
current MLO association.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250102161730.cef23352f2a2.I79c849974c494cb1cbf9e1b22a5d2d37395ff5ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently the SAE_H2E selector already exists, which needs to be
implemented by the SME. As new such selectors might be added in the
future, add a feature to permit userspace to report a selector as
supported.
If not given, the kernel should assume that userspace does support
SAE_H2E.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250101070249.fe67b871cc39.Ieb98390328927e998e612345a58b6dbc00b0e3a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This can be used to indicate that the user is not interested in receiving
locally sent packets on the monitor interface.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://patch.msgid.link/f0c20f832eadd36c71fba9a2a16ba57d78389b6c.1728462320.git-series.nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With multi-radio devices, each radio typically gets a fixed set of antennas.
In order to be able to disable specific antennas for some radios, user space
needs to know which antenna mask bits are assigned to which radio.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://patch.msgid.link/e0a26afa2c88eaa188ec96ec6d17ecac4e827641.1728462320.git-series.nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows users to prevent a vif from affecting radios other than the
configured ones. This can be useful in cases where e.g. an AP is running
on one radio, and triggering a scan on another radio should not disturb it.
Changing the allowed radios list for a vif is supported, but only while
it is down.
While it is possible to achieve the same by always explicitly specifying
a frequency list for scan requests and ensuring that the wrong channel/band
is never accidentally set on an unrelated interface, this change makes
multi-radio wiphy setups a lot easier to deal with for CLI users.
By itself, this patch only enforces the radio mask for scanning requests
and remain-on-channel. Follow-up changes build on this to limit configured
frequencies.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://patch.msgid.link/eefcb218780f71a1549875d149f1196486762756.1728462320.git-series.nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The prerequisite for MLO support in cfg80211/mac80211 is that all the links
participating in MLO must be from the same wiphy/ieee80211_hw. To meet this
expectation, some drivers may need to group multiple discrete hardware each
acting as a link in MLO under single wiphy.
With this change, supported frequencies and interface combinations of each
individual radio are reported to user space. This allows user space to figure
out the limitations of what combination of channels can be used concurrently.
Even for non-MLO devices, this improves support for devices capable of
running on multiple channels at the same time.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://patch.msgid.link/18a88f9ce82b1c9f7c12f1672430eaf2bb0be295.1720514221.git-series.nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a regulatory flag to allow VLP AP operation even on
channels otherwise marked NO_IR, which may be possible
in some regulatory domains/countries.
Note that this requires checking also when the beacon is
changed, since that may change the regulatory power type.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240523120945.63792ce19790.Ie2a02750d283b78fbf3c686b10565fb0388889e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix all of the kernel-doc issues in nl80211.h.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240319-kdoc-nl80211-v1-3-549e09d52866@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently kernel-doc raises "warning: bad line:" for several comments
that have invalid multi-line comment style; they are missing the
leading '*'. And checkpatch.pl raises "WARNING: please, no space
before tabs" for a large number of comments which have space then tab
after the leading '*'.
Fix those issues.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240319-kdoc-nl80211-v1-2-549e09d52866@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
kernel-doc flagged the following issue:
include/uapi/linux/nl80211.h:6081: warning: expecting prototype for enum nl80211_plink_action. Prototype was for enum plink_actions instead
This is because the documentation doesn't match the code. Normally the
correct fix for such an issue is to modify the documentation to match
the code. However, in this case, since the actual name plink_actions
is not referenced by any code, rename it to nl80211_plink_action to
give it a proper prefix and match the documentation.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240319-kdoc-nl80211-v1-1-549e09d52866@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a report reason for waking up due to an unprotected
deauth/disassoc when MFP is used.
If setting wowlan to wake on disconnection, and an unprotected
deatuh/disassoc arrived (in MFP), some drivers might want to
report wakeup due to unprotected deauth/disassoc, rather than
dissassociation. Add support for that.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206164849.8dc9ad531a17.I7f8e926adf927f762e11aaa3458f6354665c7fc5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the hardware supports a disabled channel, it may in
some cases be possible to use monitor mode (without any
transmit) on it when it's otherwise disabled. Add a new
channel flag IEEE80211_CHAN_CAN_MONITOR that makes it
possible for a driver to indicate such a thing.
Make it per channel so drivers could have a choice with
it, perhaps it's only possible on some channels, perhaps
some channels are not supported at all, but still there
and marked disabled.
In _nl80211_parse_chandef() simplify the code and check
only for an unknown channel, _cfg80211_chandef_usable()
will later check for IEEE80211_CHAN_DISABLED anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206164849.87fad3a21a09.I9116b2fdc2e2c9fd59a9273a64db7fcb41fc0328@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
UHB stands for "Ultra High Band", but this term doesn't really
exist in the spec. Rename all occurrences to "6 GHz", but keep
a few defines for userspace API compatibility.
Link: https://msgid.link/20240206164849.c9cfb9400839.I153db3b951934a1d84409c17fbe1f1d1782543fa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently whenever NL80211_CMD_DEL_STATION command is called without any
MAC address, all stations present on that interface are flushed.
However with MLO there is a need to flush such stations only which are
using at least a particular link from the AP MLD interface.
For example - 2 GHz and 5 GHz are part of an AP MLD.
To this interface, following stations are connected -
1. One non-EHT STA on 2 GHz link.
2. One non-EHT STA on 5 GHz link.
3. One Multi-Link STA having 2 GHz and 5 GHz as active links.
Now if currently, NL80211_CMD_DEL_STATION is issued by the 2 GHz link
without any MAC address, it would flush all station entries. However,
flushing of station entry #2 at least is not desireable since it
is connected to 5 GHz link alone.
Hence, add an option to pass link ID as well in the command so that if link
ID is passed, stations using that passed link ID alone would be flushed
and others will not.
So after this, station entries #1 and #3 alone would be flushed and #2 will
remain as it is.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240205162952.1697646-2-quic_adisi@quicinc.com
[clarify documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
sched scan"
This *mostly* reverts commit 1e1b11b6a111 ("nl80211/cfg80211: Specify
band specific min RSSI thresholds with sched scan").
During the review of a new patch [1] it was observed that the
functionality being modified was not actually being used by any
in-tree driver. Further research determined that the functionality was
originally introduced to support a new Android interface, but that
interface was subsequently abandoned. Since the functionality has
apparently never been used, remove it. However, to mantain the
sanctity of the UABI, keep the nl80211.h assignments, but clearly mark
them as obsolete.
Cc: Lin Ma <linma@zju.edu.cn>
Cc: Vamsi Krishna <quic_vamsin@quicinc.com>
Link: https://lore.kernel.org/linux-wireless/20240119151201.8670-1-linma@zju.edu.cn/ [1]
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240125-for-next-v1-1-fd79e01c6c09@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add SPP (signaling and payload protected) AMSDU support.
Since userspace has to build the RSNX element, add an extended
feature flag to indicate that this is supported.
In order to avoid downgrade/mismatch attacks, add a flag to the assoc
command on the station side, so that we can be sure that the value of
the flag comes from the same RSNX element that will be validated by
the supplicant against the 4-way-handshake. If we just pulled the
data out of a beacon/probe response, we could theoretically look an
RSNX element from a different frame, with a different value for this
flag, than the supplicant is using to validate in the
4-way-handshake.
Note that this patch is only geared towards software crypto
implementations or hardware ones that can perfectly implement SPP
A-MSDUs, i.e. are able to switch the AAD construction on the fly for
each TX/RX frame.
For more limited hardware implementations, more capability
advertisement would be required, e.g. if the hardware has no way
to switch this on the fly but has only a global configuration that
must apply to all stations.
The driver could of course *reject* mismatches, but the supplicant
must know so it can do things like not negotiating SPP A-MSDUs on
a T-DLS link when connected to an AP that doesn't support it, or
similar.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.fadac8df7030.I9240aebcba1be49636a73c647ed0af862713fc6f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
UHB AP send supported power type(LPI, SP, VLP)
in beacon and probe response IE and STA should
connect to these AP only if their regulatory support
the AP power type.
Beacon/Probe response are reported to userspace
with reason "STA regulatory not supporting to connect to AP
based on transmitted power type" and it should
not connect to AP.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.cbfbef9170a9.I432f78438de18aa9f5c9006be12e41dc34cc47c5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
FCC-594280 D01 Section B.3 allows peer-to-peer and ad hoc devices to
operate on DFS channels while they operate under the control of a
concurrent DFS master. For example, it is possible to have a P2P GO on a
DFS channel as long as BSS connection is active on the same channel.
Allow such operation by adding additional regulatory flags to indicate
DFS concurrent channels and capable devices. Add the required
relaxations in DFS regulatory checks.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.bdfb8a9c7c54.I973563562969a27fea8ec5685b96a3a47afe142f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Correct spelling as reported by codespell.
Correct run-on sentences and other grammar issues.
Add hyphenation of adjectives.
Correct some punctuation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Link: https://msgid.link/20231213044315.19459-1-rdunlap@infradead.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for setting the TID to link mapping for a non-AP MLD
station.
This is useful in cases user space needs to restrict the possible
set of active links, e.g., since it got a BSS Transition Management
request forcing to use only a subset of the valid links etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.da4d56a5f3ff.Iacf88e943326bf9c169c49b728c4a3445fdedc97@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sometimes there may be reasons for which a BSS that's
actually found in scan cannot be used to connect to,
for example a nonprimary link of an NSTR mobile AP MLD
cannot be used for normal direct connections to it.
Not indicating these to userspace as we do now of course
avoids being able to connect to them, but it's better if
they're shown to userspace and it can make an appropriate
decision, without e.g. doing an additional ML probe.
Thus add an indication of what a BSS can be used for,
currently "normal" and "MLD link", including a reason
bitmap for it being not usable.
The latter can be extended later for certain BSSes if there
are other reasons they cannot be used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.0464f25e0b1d.I9f70ca9f1440565ad9a5207d0f4d00a20cca67e7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Current handling of del pmksa with SSID is limited to FILS
security. In the current change the del pmksa support is extended
to SAE/OWE security offloads as well. For OWE/SAE offloads, the
PMK is generated and cached at driver/FW, so user app needs the
capability to request cache deletion based on SSID for drivers
supporting SAE/OWE offload.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Link: https://msgid.link/ecdae726459e0944c377a6a6f6cb2c34d2e057d0.1701262123.git.vinayak.yadawad@broadcom.com
[drop whitespace-damaged rdev_ops pointer completely, enabling tracing]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers supporting 4-way handshake offload for AP/P2p-GO and
STA/P2P-client should use this event to indicate that port has
been authorized and open for regular data traffic, sending
this event on completion of successful 4-way handshake.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Link: https://lore.kernel.org/r/f746b59f41436e9df29c24688035fbc6eb91ab06.1699510229.git.vinayak.yadawad@broadcom.com
[rewrite it all to not use the term 'GC' that we don't use
in place of P2P-client]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To extend the support of TSF accounting in scan results for MLO
connections, allow to indicate in the scan request the link ID
corresponding to the BSS whose TSF should be used for the TSF
accounting.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231113112844.d4490bcdefb1.I8fcd158b810adddef4963727e9153096416b30ce@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Correct some typos.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231001191633.19090-3-rdunlap@infradead.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Introduce new feature flags for OWE offload that driver can
advertise to indicate kernel/application space to avoid DH IE
handling. When this flag is advertised, the driver/device will
take care of DH IE inclusion and processing of peer DH IE to
generate PMK.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Link: https://lore.kernel.org/r/f891cce4b52c939dfc6b71bb2f73e560e8cad287.1695374530.git.vinayak.yadawad@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
6 GHz regulatory domains introduces Power Spectral Density (PSD).
The PSD value of the regulatory rule should be taken into effect
for the ieee80211_channels falling into that particular regulatory
rule. Save the values in the channel which has PSD value and add
nl80211 attributes accordingly to handle it.
Co-developed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230914082026.3709-1-quic_wgong@quicinc.com
[use hole in chan flags, reword docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a new flag 'update' which is set to true during start_ap()
if (and only if) one of the following two conditions are met:
- Userspace passed an empty nested attribute which indicates that
the feature should be disabled and templates deleted.
- Userspace passed all the parameters for the nested attribute.
Existing configuration will not be changed while the flag
remains false.
Add similar changes for unsolicited broadcast probe response
transmission.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20230727174100.11721-2-quic_alokad@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There really isn't any support for scanning at different
channel widths than 20 MHz since there's no way to set it.
Remove this support for now, if somebody wants to maintain
this whole thing later we can revisit how it should work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This just propagates to the channel flags, like no-HE and
similar other flags before it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230619161906.74ce2983aed8.Ifa343ba89c11760491daad5aee5a81209d5735a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
