powerpc/85xx: clean up and document the QE/FMAN microcode macros

Several macros are used to identify and locate the microcode binary image
that U-boot needs to upload to the QE or Fman.  Both the QE and the Fman
use the QE Firmware binary format to package their respective microcode data,
which is why the same macros are used for both.  A given SOC will only have
a QE or an Fman, so this is safe.

Unfortunately, the current macro definition and usage has inconsistencies.
For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman
firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address
of NAND.  There's no way to know by looking at a variable how it's supposed
to be used.

In the future, the code which uploads QE firmware and Fman firmware will
be merged.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

10 files changed, 94 insertions, 44 deletions

diff --git a/README b/README
index 07f1d11e5fe..fda0190d5ff 100644
--- a/README
+++ b/README
@@ -3274,6 +3274,44 @@ Low Level (hardware related) configuration options:
 		be used if available. These functions may be faster under some
 		conditions but may increase the binary size.
 
+Freescale QE/FMAN Firmware Support:
+-----------------------------------
+
+The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
+loading of "firmware", which is encoded in the QE firmware binary format.
+This firmware often needs to be loaded during U-Boot booting, so macros
+are used to identify the storage device (NOR flash, SPI, etc) and the address
+within that device.
+
+- CONFIG_SYS_QE_FMAN_FW_ADDR
+	The address in the storage device where the firmware is located.  The
+	meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+	is also specified.
+
+- CONFIG_SYS_QE_FMAN_FW_LENGTH
+	The maximum possible size of the firmware.  The firmware binary format
+	has a field that specifies the actual size of the firmware, but it
+	might not be possible to read any part of the firmware unless some
+	local storage is allocated to hold the entire firmware first.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_NOR
+	Specifies that QE/FMAN firmware is located in NOR flash, mapped as
+	normal addressable memory via the LBC.  CONFIG_SYS_FMAN_FW_ADDR is the
+	virtual address in NOR flash.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_NAND
+	Specifies that QE/FMAN firmware is located in NAND flash.
+	CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_MMC
+	Specifies that QE/FMAN firmware is located on the primary SD/MMC
+	device.  CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
+	Specifies that QE/FMAN firmware is located on the primary SPI
+	device.  CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+
+
 Building the Software:
 ======================
 
diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c
index 27aa038d58a..2e4a06c35ab 100644
--- a/arch/powerpc/cpu/mpc85xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c
@@ -39,7 +39,7 @@
 #include <asm/fsl_serdes.h>
 #include <linux/compiler.h>
 #include "mp.h"
-#ifdef CONFIG_SYS_QE_FW_IN_NAND
+#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND
 #include <nand.h>
 #include <errno.h>
 #endif
@@ -552,17 +552,17 @@ void cpu_secondary_init_r(void)
 {
 #ifdef CONFIG_QE
 	uint qe_base = CONFIG_SYS_IMMR + 0x00080000; /* QE immr base */
-#ifdef CONFIG_SYS_QE_FW_IN_NAND
+#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND
 	int ret;
-	size_t fw_length = CONFIG_SYS_QE_FW_LENGTH;
+	size_t fw_length = CONFIG_SYS_QE_FMAN_FW_LENGTH;
 
 	/* load QE firmware from NAND flash to DDR first */
-	ret = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FW_IN_NAND,
-			&fw_length, (u_char *)CONFIG_SYS_QE_FW_ADDR);
+	ret = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FMAN_FW_IN_NAND,
+			&fw_length, (u_char *)CONFIG_SYS_QE_FMAN_FW_ADDR);
 
 	if (ret && ret == -EUCLEAN) {
 		printf ("NAND read for QE firmware at offset %x failed %d\n",
-				CONFIG_SYS_QE_FW_IN_NAND, ret);
+				CONFIG_SYS_QE_FMAN_FW_IN_NAND, ret);
 	}
 #endif
 	qe_init(qe_base);
diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c
index a53a31d4c57..62c7ea15d02 100644
--- a/arch/powerpc/cpu/mpc85xx/fdt.c
+++ b/arch/powerpc/cpu/mpc85xx/fdt.c
@@ -466,7 +466,7 @@ void fdt_fixup_fman_firmware(void *blob)
 		return;
 	}
 
-	if (length > CONFIG_SYS_FMAN_FW_LENGTH) {
+	if (length > CONFIG_SYS_QE_FMAN_FW_LENGTH) {
 		printf("Fman firmware at %p is too large (size=%u)\n",
 		       fmanfw, length);
 		return;
diff --git a/drivers/net/fm/fm.c b/drivers/net/fm/fm.c
index 846c37249be..0b8c33fb7a3 100644
--- a/drivers/net/fm/fm.c
+++ b/drivers/net/fm/fm.c
@@ -25,11 +25,11 @@
 #include "fm.h"
 #include "../../qe/qe.h"		/* For struct qe_firmware */
 
-#ifdef CONFIG_SYS_QE_FW_IN_NAND
+#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND
 #include <nand.h>
 #elif defined(CONFIG_SYS_QE_FW_IN_SPIFLASH)
 #include <spi_flash.h>
-#elif defined(CONFIG_SYS_QE_FW_IN_MMC)
+#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_MMC)
 #include <mmc.h>
 #endif
 
@@ -363,21 +363,21 @@ int fm_init_common(int index, struct ccsr_fman *reg)
 {
 	int rc;
 	char env_addr[32];
-#if defined(CONFIG_SYS_FMAN_FW_ADDR)
-	void *addr = (void *)CONFIG_SYS_FMAN_FW_ADDR;
-#elif defined(CONFIG_SYS_QE_FW_IN_NAND)
-	size_t fw_length = CONFIG_SYS_FMAN_FW_LENGTH;
-	void *addr = malloc(CONFIG_SYS_FMAN_FW_LENGTH);
+#if defined(CONFIG_SYS_QE_FMAN_FW_IN_NOR)
+	void *addr = (void *)CONFIG_SYS_QE_FMAN_FW_ADDR;
+#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_NAND)
+	size_t fw_length = CONFIG_SYS_QE_FMAN_FW_LENGTH;
+	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
 
-	rc = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FW_IN_NAND,
+	rc = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FMAN_FW_ADDR,
 		       &fw_length, (u_char *)addr);
 	if (rc == -EUCLEAN) {
 		printf("NAND read of FMAN firmware at offset 0x%x failed %d\n",
-			CONFIG_SYS_QE_FW_IN_NAND, rc);
+			CONFIG_SYS_QE_FMAN_FW_ADDR, rc);
 	}
 #elif defined(CONFIG_SYS_QE_FW_IN_SPIFLASH)
 	struct spi_flash *ucode_flash;
-	void *addr = malloc(CONFIG_SYS_FMAN_FW_LENGTH);
+	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
 	int ret = 0;
 
 	ucode_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
@@ -385,17 +385,17 @@ int fm_init_common(int index, struct ccsr_fman *reg)
 	if (!ucode_flash)
 		printf("SF: probe for ucode failed\n");
 	else {
-		ret = spi_flash_read(ucode_flash, CONFIG_SYS_QE_FW_IN_SPIFLASH,
-				CONFIG_SYS_FMAN_FW_LENGTH, addr);
+		ret = spi_flash_read(ucode_flash, CONFIG_SYS_QE_FMAN_FW_ADDR,
+				CONFIG_SYS_QE_FMAN_FW_LENGTH, addr);
 		if (ret)
 			printf("SF: read for ucode failed\n");
 		spi_flash_free(ucode_flash);
 	}
-#elif defined(CONFIG_SYS_QE_FW_IN_MMC)
+#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_MMC)
 	int dev = CONFIG_SYS_MMC_ENV_DEV;
-	void *addr = malloc(CONFIG_SYS_FMAN_FW_LENGTH);
-	u32 cnt = CONFIG_SYS_FMAN_FW_LENGTH / 512;
-	u32 blk = CONFIG_SYS_QE_FW_IN_MMC / 512;
+	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
+	u32 cnt = CONFIG_SYS_QE_FMAN_FW_LENGTH / 512;
+	u32 blk = CONFIG_SYS_QE_FMAN_FW_ADDR / 512;
 	struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);
 
 	if (!mmc)
diff --git a/drivers/qe/qe.c b/drivers/qe/qe.c
index c4ec2f4af89..9f711519ede 100644
--- a/drivers/qe/qe.c
+++ b/drivers/qe/qe.c
@@ -170,11 +170,11 @@ void qe_init(uint qe_base)
 	/* Init the QE IMMR base */
 	qe_immr = (qe_map_t *)qe_base;
 
-#ifdef CONFIG_SYS_QE_FW_ADDR
+#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NOR
 	/*
 	 * Upload microcode to IRAM for those SOCs which do not have ROM in QE.
 	 */
-	qe_upload_firmware((const struct qe_firmware *) CONFIG_SYS_QE_FW_ADDR);
+	qe_upload_firmware((const void *)CONFIG_SYS_QE_FMAN_FW_ADDR);
 
 	/* enable the microcode in IRAM */
 	out_be32(&qe_immr->iram.iready,QE_IRAM_READY);
diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h
index ab27b9895a2..7a5d86d2b7b 100644
--- a/include/configs/MPC8569MDS.h
+++ b/include/configs/MPC8569MDS.h
@@ -510,7 +510,8 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
 /* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FW_ADDR	0xfff00000
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xfff00000
 
 /*
  * BOOTP options
diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h
index 013a6acdca2..e057b1f9459 100644
--- a/include/configs/P1023RDS.h
+++ b/include/configs/P1023RDS.h
@@ -526,12 +526,14 @@ extern unsigned long get_clock_freq(void);
 #ifndef CONFIG_NAND
 /* Default address of microcode for the Linux Fman driver */
 /* QE microcode/firmware address */
-#define CONFIG_SYS_FMAN_FW_ADDR		0xEF000000
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEF000000
 #else
-#define CONFIG_SYS_QE_FW_IN_NAND	0x1f00000
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x1f00000
 #endif
-#define CONFIG_SYS_FMAN_FW_LENGTH	0x10000
-#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_FMAN_FW_LENGTH)
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 
 #ifdef CONFIG_FMAN_ENET
 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR	0x2
diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h
index f9fe3cf9520..a48055e2c5e 100644
--- a/include/configs/P2041RDB.h
+++ b/include/configs/P2041RDB.h
@@ -414,21 +414,25 @@ unsigned long get_board_sys_clk(unsigned long dummy);
  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
  * env, so we got 0x110000.
  */
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH	0x110000
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
  * about 545KB (1089 blocks), Env is stored after the image, and the env size is
  * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
  */
-#define CONFIG_SYS_QE_FW_IN_MMC		(512 * 1130)
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
 #elif defined(CONFIG_NAND)
-#define CONFIG_SYS_QE_FW_IN_NAND	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
-#define CONFIG_SYS_FMAN_FW_ADDR		0xEF000000
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEF000000
 #endif
-#define CONFIG_SYS_FMAN_FW_LENGTH	0x10000
-#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_FMAN_FW_LENGTH)
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 
 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_FMAN_ENET
diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h
index bc0aeebb441..0622b9fcfdd 100644
--- a/include/configs/corenet_ds.h
+++ b/include/configs/corenet_ds.h
@@ -474,21 +474,25 @@
  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
  * env, so we got 0x110000.
  */
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH	0x110000
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
  * about 545KB (1089 blocks), Env is stored after the image, and the env size is
  * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
  */
-#define CONFIG_SYS_QE_FW_IN_MMC		(512 * 1130)
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
 #elif defined(CONFIG_NAND)
-#define CONFIG_SYS_QE_FW_IN_NAND	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
-#define CONFIG_SYS_FMAN_FW_ADDR		0xEF000000
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEF000000
 #endif
-#define CONFIG_SYS_FMAN_FW_LENGTH	0x10000
-#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_FMAN_FW_LENGTH)
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 
 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_FMAN_ENET
diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index 5a69902f899..8e8fa163b8a 100644
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -677,8 +677,9 @@
 
 #ifdef CONFIG_QE
 /* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FW_ADDR		0xefec0000
-#define CONFIG_SYS_QE_FW_LENGTH		0x10000
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xefec0000
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #endif /* CONFIG_QE */
 
 #ifdef CONFIG_P1025RDB