Merge git://git.denx.de/u-boot-rockchip

This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.

1 files changed, 52 insertions, 10 deletions

diff --git a/drivers/spi/rk_spi.c b/drivers/spi/rk_spi.c
index 3e44f1795e3..ea209801a73 100644
--- a/drivers/spi/rk_spi.c
+++ b/drivers/spi/rk_spi.c
@@ -79,12 +79,31 @@ static void rkspi_enable_chip(struct rockchip_spi *regs, bool enable)
 
 static void rkspi_set_clk(struct rockchip_spi_priv *priv, uint speed)
 {
-	uint clk_div;
+	/*
+	 * We should try not to exceed the speed requested by the caller:
+	 * when selecting a divider, we need to make sure we round up.
+	 */
+	uint clk_div = DIV_ROUND_UP(priv->input_rate, speed);
+
+	/* The baudrate register (BAUDR) is defined as a 32bit register where
+	 * the upper 16bit are reserved and having 'Fsclk_out' in the lower
+	 * 16bits with 'Fsclk_out' defined as follows:
+	 *
+	 *   Fsclk_out = Fspi_clk/ SCKDV
+	 *   Where SCKDV is any even value between 2 and 65534.
+	 */
+	if (clk_div > 0xfffe) {
+		clk_div = 0xfffe;
+		debug("%s: can't divide down to %d hz (actual will be %d hz)\n",
+		      __func__, speed, priv->input_rate / clk_div);
+	}
+
+	/* Round up to the next even 16bit number */
+	clk_div = (clk_div + 1) & 0xfffe;
 
-	clk_div = clk_get_divisor(priv->input_rate, speed);
 	debug("spi speed %u, div %u\n", speed, clk_div);
 
-	writel(clk_div, &priv->regs->baudr);
+	clrsetbits_le32(&priv->regs->baudr, 0xffff, clk_div);
 	priv->last_speed_hz = speed;
 }
 
@@ -190,6 +209,26 @@ static int rockchip_spi_ofdata_to_platdata(struct udevice *bus)
 	return 0;
 }
 
+static int rockchip_spi_calc_modclk(ulong max_freq)
+{
+	unsigned div;
+	const unsigned long gpll_hz = 594000000UL;
+
+	/*
+	 * We need to find an input clock that provides at least twice
+	 * the maximum frequency and can be generated from the assumed
+	 * speed of GPLL (594MHz) using an integer divider.
+	 *
+	 * To give us more achievable bitrates at higher speeds (these
+	 * are generated by dividing by an even 16-bit integer from
+	 * this frequency), we try to have an input frequency of at
+	 * least 4x our max_freq.
+	 */
+
+	div = DIV_ROUND_UP(gpll_hz, max_freq * 4);
+	return gpll_hz / div;
+}
+
 static int rockchip_spi_probe(struct udevice *bus)
 {
 	struct rockchip_spi_platdata *plat = dev_get_platdata(bus);
@@ -207,11 +246,13 @@ static int rockchip_spi_probe(struct udevice *bus)
 	priv->last_transaction_us = timer_get_us();
 	priv->max_freq = plat->frequency;
 
-	/*
-	 * Use 99 MHz as our clock since it divides nicely into 594 MHz which
-	 * is the assumed speed for CLK_GENERAL.
-	 */
-	ret = clk_set_rate(&priv->clk, 99000000);
+	/* Clamp the value from the DTS against any hardware limits */
+	if (priv->max_freq > ROCKCHIP_SPI_MAX_RATE)
+		priv->max_freq = ROCKCHIP_SPI_MAX_RATE;
+
+	/* Find a module-input clock that fits with the max_freq setting */
+	ret = clk_set_rate(&priv->clk,
+			   rockchip_spi_calc_modclk(priv->max_freq));
 	if (ret < 0) {
 		debug("%s: Failed to set clock: %d\n", __func__, ret);
 		return ret;
@@ -371,10 +412,10 @@ static int rockchip_spi_set_speed(struct udevice *bus, uint speed)
 {
 	struct rockchip_spi_priv *priv = dev_get_priv(bus);
 
-	if (speed > ROCKCHIP_SPI_MAX_RATE)
-		return -EINVAL;
+	/* Clamp to the maximum frequency specified in the DTS */
 	if (speed > priv->max_freq)
 		speed = priv->max_freq;
+
 	priv->speed_hz = speed;
 
 	return 0;
@@ -403,6 +444,7 @@ static const struct dm_spi_ops rockchip_spi_ops = {
 
 static const struct udevice_id rockchip_spi_ids[] = {
 	{ .compatible = "rockchip,rk3288-spi" },
+	{ .compatible = "rockchip,rk3399-spi" },
 	{ }
 };