Merge tag 'v2025.07-rc3' into next

Prepare v2025.07-rc3

6 files changed, 22 insertions, 106 deletions

diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index a35b8c2f646..847fa1f82c3 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -23,6 +23,7 @@
 #include <linux/delay.h>
 #include <linux/dma-mapping.h>
 #include <linux/err.h>
+#include <linux/iopoll.h>
 #include <linux/ioport.h>
 #include <dm.h>
 #include <generic-phy.h>
@@ -587,7 +588,6 @@ static void dwc3_set_incr_burst_type(struct dwc3 *dwc)
  */
 static int dwc3_core_init(struct dwc3 *dwc)
 {
-	unsigned long		timeout;
 	u32			hwparams4 = dwc->hwparams.hwparams4;
 	u32			reg;
 	int			ret;
@@ -610,15 +610,11 @@ static int dwc3_core_init(struct dwc3 *dwc)
 	}
 
 	/* issue device SoftReset too */
-	timeout = 5000;
 	dwc3_writel(dwc->regs, DWC3_DCTL, DWC3_DCTL_CSFTRST);
-	while (timeout--) {
-		reg = dwc3_readl(dwc->regs, DWC3_DCTL);
-		if (!(reg & DWC3_DCTL_CSFTRST))
-			break;
-	};
-
-	if (!timeout) {
+	ret = read_poll_timeout(dwc3_readl, reg,
+				!(reg & DWC3_DCTL_CSFTRST),
+				1, 5000, dwc->regs, DWC3_DCTL);
+	if (ret) {
 		dev_err(dwc->dev, "Reset Timed Out\n");
 		ret = -ETIMEDOUT;
 		goto err0;
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 3dc79770eeb..5c9e8fc9d15 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -262,7 +262,7 @@ endif
 config USB_EHCI_MSM
 	bool "Support for Qualcomm on-chip EHCI USB controller"
 	depends on DM_USB
-	select USB_ULPI_VIEWPORT
+	select USB_ULPI
 	select MSM8916_USB_PHY
 	---help---
 	  Enables support for the on-chip EHCI controller on Qualcomm
@@ -279,7 +279,10 @@ config USB_EHCI_TEGRA
 	depends on ARCH_TEGRA
 	select USB_EHCI_IS_TDI
 	---help---
-	  Enable support for Tegra on-chip EHCI USB controller
+	  Enable support for Tegra on-chip EHCI USB controller. If you enable
+	  ULPI and your PHY needs a different reference clock than the standard
+	  24 MHz then you have to define CFG_ULPI_REF_CLK to the appropriate
+	  value in Hz.
 
 config USB_EHCI_ZYNQ
 	bool "Support for Xilinx Zynq on-chip EHCI USB controller"
diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c
index 7c73eb66b60..89b87886da1 100644
--- a/drivers/usb/host/ehci-tegra.c
+++ b/drivers/usb/host/ehci-tegra.c
@@ -25,13 +25,6 @@
 #define HOSTPC1_DEVLC	0x84
 #define HOSTPC1_PSPD(x)		(((x) >> 25) & 0x3)
 
-#ifdef CONFIG_USB_ULPI
-	#ifndef CONFIG_USB_ULPI_VIEWPORT
-	#error	"To use CONFIG_USB_ULPI on Tegra Boards you have to also \
-		define CONFIG_USB_ULPI_VIEWPORT"
-	#endif
-#endif
-
 /* Parameters we need for USB */
 enum {
 	PARAM_DIVN,                     /* PLL FEEDBACK DIVIDer */
diff --git a/drivers/usb/ulpi/Kconfig b/drivers/usb/ulpi/Kconfig
index 001564d40c6..d969360f7eb 100644
--- a/drivers/usb/ulpi/Kconfig
+++ b/drivers/usb/ulpi/Kconfig
@@ -1,8 +1,18 @@
 comment "ULPI drivers"
 
+config USB_ULPI
+	bool "ULPI support"
+	depends on USB_HOST
+	help
+	  Select to commnicate with USB PHY via ULPI interface.
+	  The ULPI (UTMI Low Pin (count) Interface) is a wrapper on UTMI+ core
+	  that is used as PHY Transreceiver for USB controllers.
+
+	  This driver uses ULPI viewports that are specific for each SoC.
+
 choice
 	prompt "ULPI Viewport type"
-	optional
+	depends on USB_ULPI
 	help
 	  Select ULPI viewport (SoC-side interface to ULPI) implementation
 	  appropriate for the device if you want to communicate with
@@ -10,23 +20,9 @@ choice
 
 config USB_ULPI_VIEWPORT
 	bool "Generic ULPI Viewport"
+	depends on USB_ULPI
 	help
 	  Support generic ULPI Viewport implementation that is used on
 	  some Tegra and Snapdragon devices.
 
-config USB_ULPI_VIEWPORT_OMAP
-	bool "OMAP ULPI Viewport"
-	help
-	  Support ULPI Viewport implementation that is used on OMAP devices.
-
 endchoice
-
-config USB_ULPI
-	bool "ULPI support"
-	depends on (USB_ULPI_VIEWPORT || USB_ULPI_VIEWPORT_OMAP)
-	help
-	  Select to commnicate with USB PHY via ULPI interface.
-	  ULPI is wrapper on UTMI+ core that is used as
-	  PHY Transreceiver for USB controllers.
-
-	  This driver uses ULPI viewports that are specific for each SoC.
diff --git a/drivers/usb/ulpi/Makefile b/drivers/usb/ulpi/Makefile
index f05b7743531..5565948bc12 100644
--- a/drivers/usb/ulpi/Makefile
+++ b/drivers/usb/ulpi/Makefile
@@ -4,4 +4,3 @@
 
 obj-$(CONFIG_USB_ULPI)		+= ulpi.o
 obj-$(CONFIG_USB_ULPI_VIEWPORT)	+= ulpi-viewport.o
-obj-$(CONFIG_USB_ULPI_VIEWPORT_OMAP)	+= omap-ulpi-viewport.o
diff --git a/drivers/usb/ulpi/omap-ulpi-viewport.c b/drivers/usb/ulpi/omap-ulpi-viewport.c
deleted file mode 100644
index 6f0c3eb154e..00000000000
--- a/drivers/usb/ulpi/omap-ulpi-viewport.c
+++ /dev/null
@@ -1,71 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * OMAP ulpi viewport support
- * Based on drivers/usb/ulpi/ulpi-viewport.c
- *
- * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com
- * Author: Govindraj R <govindraj.raja@ti.com>
- */
-
-#include <log.h>
-#include <asm/io.h>
-#include <linux/delay.h>
-#include <usb/ulpi.h>
-
-#define OMAP_ULPI_WR_OPSEL	(2 << 22)
-#define OMAP_ULPI_RD_OPSEL	(3 << 22)
-#define OMAP_ULPI_START		(1 << 31)
-
-/*
- * Wait for having ulpi in done state
- */
-static int ulpi_wait(struct ulpi_viewport *ulpi_vp, u32 mask)
-{
-	int timeout = CFG_USB_ULPI_TIMEOUT;
-
-	while (--timeout) {
-		if (!(readl(ulpi_vp->viewport_addr) & mask))
-			return 0;
-
-		udelay(1);
-	}
-
-	return ULPI_ERROR;
-}
-
-/*
- * Issue a ULPI read/write request
- */
-static int ulpi_request(struct ulpi_viewport *ulpi_vp, u32 value)
-{
-	int err;
-
-	writel(value, ulpi_vp->viewport_addr);
-
-	err = ulpi_wait(ulpi_vp, OMAP_ULPI_START);
-	if (err)
-		debug("ULPI request timed out\n");
-
-	return err;
-}
-
-int ulpi_write(struct ulpi_viewport *ulpi_vp, u8 *reg, u32 value)
-{
-	u32 val = OMAP_ULPI_START | (((ulpi_vp->port_num + 1) & 0xf) << 24) |
-			OMAP_ULPI_WR_OPSEL | ((u32)reg << 16) | (value & 0xff);
-
-	return ulpi_request(ulpi_vp, val);
-}
-
-u32 ulpi_read(struct ulpi_viewport *ulpi_vp, u8 *reg)
-{
-	int err;
-	u32 val = OMAP_ULPI_START | (((ulpi_vp->port_num + 1) & 0xf) << 24) |
-			 OMAP_ULPI_RD_OPSEL | ((u32)reg << 16);
-
-	err = ulpi_request(ulpi_vp, val);
-	if (err)
-		return err;
-
-	return readl(ulpi_vp->viewport_addr) & 0xff;
-}