4 files changed, 13 insertions, 5 deletions
diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
index 872fcfe3cb5..510050f3920 100644
--- a/drivers/mmc/Kconfig
+++ b/drivers/mmc/Kconfig
@@ -20,11 +20,19 @@ config MMC_WRITE
 
 config MMC_PWRSEQ
 	bool "HW reset support for eMMC"
-	depends on PWRSEQ
+	depends on PWRSEQ && DM_GPIO
 	help
-	  Ths select Hardware reset support aka pwrseq-emmc for eMMC
+	  This select Hardware reset support aka pwrseq-emmc for eMMC
 	  devices.
 
+config SPL_MMC_PWRSEQ
+	bool "HW reset support for eMMC in SPL"
+	depends on SPL_PWRSEQ && SPL_DM_GPIO
+	default y if MMC_PWRSEQ
+	help
+	  This select Hardware reset support aka pwrseq-emmc for eMMC
+	  devices in SPL.
+
 config MMC_BROKEN_CD
 	bool "Poll for broken card detection case"
 	help
diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
index 3374321e290..72c3fb66ce0 100644
--- a/drivers/mmc/Makefile
+++ b/drivers/mmc/Makefile
@@ -11,7 +11,7 @@ obj-$(CONFIG_$(SPL_TPL_)BOOTSTD) += mmc_bootdev.o
 endif
 
 obj-$(CONFIG_$(SPL_TPL_)MMC_WRITE) += mmc_write.o
-obj-$(CONFIG_MMC_PWRSEQ) += mmc-pwrseq.o
+obj-$(CONFIG_$(SPL_)MMC_PWRSEQ) += mmc-pwrseq.o
 obj-$(CONFIG_MMC_SDHCI_ADMA_HELPERS) += sdhci-adma.o
 
 ifndef CONFIG_$(SPL_)BLK
diff --git a/drivers/mmc/meson_gx_mmc.c b/drivers/mmc/meson_gx_mmc.c
index fcf4f03d1e2..0825c0a2a83 100644
--- a/drivers/mmc/meson_gx_mmc.c
+++ b/drivers/mmc/meson_gx_mmc.c
@@ -288,7 +288,7 @@ static int meson_mmc_probe(struct udevice *dev)
 
 	mmc_set_clock(mmc, cfg->f_min, MMC_CLK_ENABLE);
 
-#ifdef CONFIG_MMC_PWRSEQ
+#if CONFIG_IS_ENABLED(MMC_PWRSEQ)
 	/* Enable power if needed */
 	ret = mmc_pwrseq_get_power(dev, cfg);
 	if (!ret) {
diff --git a/drivers/mmc/rockchip_dw_mmc.c b/drivers/mmc/rockchip_dw_mmc.c
index 72c820ee633..ad4529d6afa 100644
--- a/drivers/mmc/rockchip_dw_mmc.c
+++ b/drivers/mmc/rockchip_dw_mmc.c
@@ -145,7 +145,7 @@ static int rockchip_dwmmc_probe(struct udevice *dev)
 
 	host->fifo_mode = priv->fifo_mode;
 
-#ifdef CONFIG_MMC_PWRSEQ
+#if CONFIG_IS_ENABLED(MMC_PWRSEQ)
 	/* Enable power if needed */
 	ret = mmc_pwrseq_get_power(dev, &plat->cfg);
 	if (!ret) {