diff options
Diffstat (limited to 'include/configs/clearfog.h')
| -rw-r--r-- | include/configs/clearfog.h | 117 |
1 files changed, 117 insertions, 0 deletions
diff --git a/include/configs/clearfog.h b/include/configs/clearfog.h new file mode 100644 index 00000000000..7c7ada15bd9 --- /dev/null +++ b/include/configs/clearfog.h @@ -0,0 +1,117 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2015 Stefan Roese <sr@denx.de> + */ + +#ifndef _CONFIG_CLEARFOG_H +#define _CONFIG_CLEARFOG_H + +#include <linux/stringify.h> + +/* + * High Level Configuration Options (easy to change) + */ + +/* + * TEXT_BASE needs to be below 16MiB, since this area is scrubbed + * for DDR ECC byte filling in the SPL before loading the main + * U-Boot into it. + */ + +/* Environment in MMC */ +/* + * For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC + * boot image starts @ LBA-0. + * As result in MMC/eMMC case it will be a 1 sector gap between u-boot + * image and environment + */ + +/* Keep device tree and initrd in lower memory so the kernel can access them */ +#define RELOCATION_LIMITS_ENV_SETTINGS \ + "fdt_high=0x10000000\0" \ + "initrd_high=0x10000000\0" + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* Include the common distro boot environment */ +#ifdef CONFIG_MMC +#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0) +#else +#define BOOT_TARGET_DEVICES_MMC(func) +#endif + +#ifdef CONFIG_USB_STORAGE +#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) +#else +#define BOOT_TARGET_DEVICES_USB(func) +#endif + +#ifndef CONFIG_SCSI +#define BOOT_TARGET_DEVICES_SCSI_BUS0(func) +#define BOOT_TARGET_DEVICES_SCSI_BUS1(func) +#define BOOT_TARGET_DEVICES_SCSI_BUS2(func) +#else +/* + * With SCSI enabled, M.2 SATA is always located on bus 0 + */ +#define BOOT_TARGET_DEVICES_SCSI_BUS0(func) func(SCSI, scsi, 0) + +/* + * Either one or both mPCIe slots may be configured as mSATA interfaces. The + * SCSI bus ids are assigned based on sequence of hardware present, not always + * tied to hardware slot ids. As such, use second SCSI bus if either slot is + * set for SATA, and only use third SCSI bus if both slots are SATA enabled. + */ +#if defined (CONFIG_CLEARFOG_CON2_SATA) || defined (CONFIG_CLEARFOG_CON3_SATA) +#define BOOT_TARGET_DEVICES_SCSI_BUS1(func) func(SCSI, scsi, 1) +#else +#define BOOT_TARGET_DEVICES_SCSI_BUS1(func) +#endif + +#if defined (CONFIG_CLEARFOG_CON2_SATA) && defined (CONFIG_CLEARFOG_CON3_SATA) +#define BOOT_TARGET_DEVICES_SCSI_BUS2(func) func(SCSI, scsi, 2) +#else +#define BOOT_TARGET_DEVICES_SCSI_BUS2(func) +#endif + +#endif /* CONFIG_SCSI */ + +/* + * The SCSI buses are attempted in increasing bus order, there is no current + * mechanism to alter the default bus priority order for booting. + */ +#define BOOT_TARGET_DEVICES(func) \ + BOOT_TARGET_DEVICES_MMC(func) \ + BOOT_TARGET_DEVICES_USB(func) \ + BOOT_TARGET_DEVICES_SCSI_BUS0(func) \ + BOOT_TARGET_DEVICES_SCSI_BUS1(func) \ + BOOT_TARGET_DEVICES_SCSI_BUS2(func) \ + func(PXE, pxe, na) \ + func(DHCP, dhcp, na) + +#define KERNEL_ADDR_R __stringify(0x800000) +#define FDT_ADDR_R __stringify(0x100000) +#define RAMDISK_ADDR_R __stringify(0x1800000) +#define SCRIPT_ADDR_R __stringify(0x200000) +#define PXEFILE_ADDR_R __stringify(0x300000) + +#define LOAD_ADDRESS_ENV_SETTINGS \ + "kernel_addr_r=" KERNEL_ADDR_R "\0" \ + "fdt_addr_r=" FDT_ADDR_R "\0" \ + "ramdisk_addr_r=" RAMDISK_ADDR_R "\0" \ + "scriptaddr=" SCRIPT_ADDR_R "\0" \ + "pxefile_addr_r=" PXEFILE_ADDR_R "\0" + +#include <config_distro_bootcmd.h> + +#define CFG_EXTRA_ENV_SETTINGS \ + RELOCATION_LIMITS_ENV_SETTINGS \ + LOAD_ADDRESS_ENV_SETTINGS \ + "console=ttyS0,115200\0" \ + BOOTENV + +#endif /* _CONFIG_CLEARFOG_H */ |