diff options
Diffstat (limited to 'include/configs/lx2160a_common.h')
| -rw-r--r-- | include/configs/lx2160a_common.h | 226 |
1 files changed, 226 insertions, 0 deletions
diff --git a/include/configs/lx2160a_common.h b/include/configs/lx2160a_common.h new file mode 100644 index 00000000000..4c1b4bf2b2c --- /dev/null +++ b/include/configs/lx2160a_common.h @@ -0,0 +1,226 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018-2021 NXP + */ + +#ifndef __LX2_COMMON_H +#define __LX2_COMMON_H + +#include <asm/arch/stream_id_lsch3.h> +#include <asm/arch/config.h> +#include <asm/arch/soc.h> + +#define CFG_SYS_FLASH_BASE 0x20000000 + +/* DDR */ +#define CFG_SYS_DDR_SDRAM_BASE 0x80000000UL +#define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 +#define CFG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL +#define CFG_SYS_SDRAM_SIZE 0x200000000UL +#define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE +#define SPD_EEPROM_ADDRESS1 0x51 +#define SPD_EEPROM_ADDRESS2 0x52 +#define SPD_EEPROM_ADDRESS3 0x53 +#define SPD_EEPROM_ADDRESS4 0x54 +#define SPD_EEPROM_ADDRESS5 0x55 +#define SPD_EEPROM_ADDRESS6 0x56 +#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 + +/* Miscellaneous configurable options */ + +/* SMP Definitinos */ +#define CPU_RELEASE_ADDR secondary_boot_addr + +/* Generic Timer Definitions */ +/* + * This is not an accurate number. It is used in start.S. The frequency + * will be udpated later when get_bus_freq(0) is available. + */ + +/* Serial Port */ +#define CFG_PL011_CLOCK (get_bus_freq(0) / 4) +#define CFG_SYS_SERIAL0 0x21c0000 +#define CFG_SYS_SERIAL1 0x21d0000 +#define CFG_SYS_SERIAL2 0x21e0000 +#define CFG_SYS_SERIAL3 0x21f0000 +/*below might needs to be removed*/ +#define CFG_PL01x_PORTS {(void *)CFG_SYS_SERIAL0, \ + (void *)CFG_SYS_SERIAL1, \ + (void *)CFG_SYS_SERIAL2, \ + (void *)CFG_SYS_SERIAL3 } + +/* MC firmware */ +#define CFG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000 +#define CFG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000 +#define CFG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000 +#define CFG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000 +#define CFG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 + +/* + * Carve out a DDR region which will not be used by u-boot/Linux + * + * It will be used by MC and Debug Server. The MC region must be + * 512MB aligned, so the min size to hide is 512MB. + */ +#ifdef CONFIG_FSL_MC_ENET +#define CFG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024) +#endif + +/* I2C bus multiplexer */ +#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/ +#define I2C_MUX_CH_DEFAULT 0x8 + +/* RTC */ +#define CFG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/ + +/* Qixis */ +#define CFG_SYS_I2C_FPGA_ADDR 0x66 + +/* USB */ + +#define COUNTER_FREQUENCY_REAL (get_board_sys_clk() / 4) + +#define HWCONFIG_BUFFER_SIZE 128 + +/* Initial environment variables */ +#define XSPI_MC_INIT_CMD \ + "sf probe 0:0 && " \ + "sf read 0x80640000 0x640000 0x80000 && " \ + "sf read $fdt_addr_r 0xf00000 0x100000 && " \ + "env exists secureboot && " \ + "esbc_validate 0x80640000 && " \ + "esbc_validate 0x80680000; " \ + "sf read 0x80a00000 0xa00000 0x300000 && " \ + "sf read 0x80e00000 0xe00000 0x100000; " \ + "fsl_mc start mc 0x80a00000 0x80e00000\0" + +#define SD_MC_INIT_CMD \ + "mmc read 0x80a00000 0x5000 0x1200;" \ + "mmc read 0x80e00000 0x7000 0x800;" \ + "mmc read $fdt_addr_r 0x7800 0x800;" \ + "env exists secureboot && " \ + "mmc read 0x80640000 0x3200 0x20 && " \ + "mmc read 0x80680000 0x3400 0x20 && " \ + "esbc_validate 0x80640000 && " \ + "esbc_validate 0x80680000 ;" \ + "fsl_mc start mc 0x80a00000 0x80e00000\0" + +#define SD2_MC_INIT_CMD \ + "mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;" \ + "mmc read 0x80e00000 0x7000 0x800;" \ + "mmc read $fdt_addr_r 0x7800 0x800;" \ + "env exists secureboot && " \ + "mmc read 0x80640000 0x3200 0x20 && " \ + "mmc read 0x80680000 0x3400 0x20 && " \ + "esbc_validate 0x80640000 && " \ + "esbc_validate 0x80680000 ;" \ + "fsl_mc start mc 0x80a00000 0x80e00000\0" + +#define EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:bank_intlv=auto\0" \ + "ramdisk_addr=0x800000\0" \ + "ramdisk_size=0x2000000\0" \ + "fdt_high=0xa0000000\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "kernel_start=0x1000000\0" \ + "kernelheader_start=0x600000\0" \ + "scriptaddr=0x80000000\0" \ + "scripthdraddr=0x80080000\0" \ + "fdtheader_addr_r=0x80100000\0" \ + "kernelheader_addr_r=0x80200000\0" \ + "kernel_addr_r=0x81000000\0" \ + "kernelheader_size=0x40000\0" \ + "fdt_addr_r=0x90000000\0" \ + "load_addr=0xa0000000\0" \ + "kernel_size=0x2800000\0" \ + "kernel_addr_sd=0x8000\0" \ + "kernelhdr_addr_sd=0x3000\0" \ + "kernel_size_sd=0x14000\0" \ + "kernelhdr_size_sd=0x20\0" \ + "console=ttyAMA0,38400n8\0" \ + BOOTENV \ + "mcmemsize=0x70000000\0" \ + XSPI_MC_INIT_CMD \ + "scan_dev_for_boot_part=" \ + "part list ${devtype} ${devnum} devplist; " \ + "env exists devplist || setenv devplist 1; " \ + "for distro_bootpart in ${devplist}; do " \ + "if fstype ${devtype} " \ + "${devnum}:${distro_bootpart} " \ + "bootfstype; then " \ + "run scan_dev_for_boot; " \ + "fi; " \ + "done\0" \ + "boot_a_script=" \ + "load ${devtype} ${devnum}:${distro_bootpart} " \ + "${scriptaddr} ${prefix}${script}; " \ + "env exists secureboot && load ${devtype} " \ + "${devnum}:${distro_bootpart} " \ + "${scripthdraddr} ${prefix}${boot_script_hdr} " \ + "&& esbc_validate ${scripthdraddr};" \ + "source ${scriptaddr}\0" + +#define XSPI_NOR_BOOTCOMMAND \ + "sf probe 0:0; " \ + "sf read 0x806c0000 0x6c0000 0x40000; " \ + "env exists mcinitcmd && env exists secureboot" \ + " && esbc_validate 0x806c0000; " \ + "sf read 0x80d00000 0xd00000 0x100000; " \ + "env exists mcinitcmd && " \ + "fsl_mc lazyapply dpl 0x80d00000; " \ + "run distro_bootcmd;run xspi_bootcmd; " \ + "env exists secureboot && esbc_halt;" + +#define SD_BOOTCOMMAND \ + "env exists mcinitcmd && mmcinfo; " \ + "mmc read 0x80d00000 0x6800 0x800; " \ + "env exists mcinitcmd && env exists secureboot " \ + " && mmc read 0x806C0000 0x3600 0x20 " \ + "&& esbc_validate 0x806C0000;env exists mcinitcmd " \ + "&& fsl_mc lazyapply dpl 0x80d00000;" \ + "run distro_bootcmd;run sd_bootcmd;" \ + "env exists secureboot && esbc_halt;" + +#define SD2_BOOTCOMMAND \ + "mmc dev 1; env exists mcinitcmd && mmcinfo; " \ + "mmc read 0x80d00000 0x6800 0x800; " \ + "env exists mcinitcmd && env exists secureboot " \ + " && mmc read 0x806C0000 0x3600 0x20 " \ + "&& esbc_validate 0x806C0000;env exists mcinitcmd " \ + "&& fsl_mc lazyapply dpl 0x80d00000;" \ + "run distro_bootcmd;run sd2_bootcmd;" \ + "env exists secureboot && esbc_halt;" + +#ifdef CONFIG_CMD_USB +#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) +#else +#define BOOT_TARGET_DEVICES_USB(func) +#endif + +#ifdef CONFIG_MMC +#define BOOT_TARGET_DEVICES_MMC(func, instance) func(MMC, mmc, instance) +#else +#define BOOT_TARGET_DEVICES_MMC(func) +#endif + +#ifdef CONFIG_SCSI +#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0) +#else +#define BOOT_TARGET_DEVICES_SCSI(func) +#endif + +#ifdef CONFIG_CMD_DHCP +#define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na) +#else +#define BOOT_TARGET_DEVICES_DHCP(func) +#endif + +#define BOOT_TARGET_DEVICES(func) \ + BOOT_TARGET_DEVICES_USB(func) \ + BOOT_TARGET_DEVICES_MMC(func, 0) \ + BOOT_TARGET_DEVICES_MMC(func, 1) \ + BOOT_TARGET_DEVICES_SCSI(func) \ + BOOT_TARGET_DEVICES_DHCP(func) +#include <config_distro_bootcmd.h> + +#endif /* __LX2_COMMON_H */ |