| Age | Commit message (Collapse) | Author |
|---|
|
HyperFlash
The size of J7200 tiboot3.bin is 516KB but the memory reserved for it in
HyperFlash was 512KB. This led to overlap of tiboot3.bin over tispl.bin
region and break in HyperFlash boot mode.
Therefore, fix this by increasing the memory allocated for tiboot3.bin
to 1MB for J7200.
Fixes: cf1d6867f774 ("board: ti: j7200: Introduce support for j7200 build targets")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Kernel commit 5b2671594b80 ("configs: j721e: Remove HBMC_AM654
config") removed the HBMC_AM654 config because hbmc was broken
in u-boot. Hence, add the missing configs necessary to re-enable
Hyperflash boot.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Add 32-bit address overrides for Hyper Bus Memory Controller
for Hyperflash to be functional in R5 SPL.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Add 32-bit address overrides for Hyper Bus Memory Controller
for Hyperflash to be functional in R5 SPL.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
The syscon APIs were used for selecting the state of the mux
device because the mmio-mux driver in u-boot did not support
the mux functionality when the parent device is not a syscon.
Change to mux APIs which utilizes the reg-mux driver to select the
state of the multiplexer.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Add config required to build mmio-mux driver and dependencies.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Since net_test_wget() is testing a command and is in test/cmd it should
be in the 'cmd' test suite, not 'lib'.
Saving and restoring the values of the environment variables that the
test manipulates is necessary to avoid a regression when running the
whole ut test suite. A minimal reproducer is:
$ ./u-boot -T -c "ut cmd net_test_wget; ut dm dm_test_eth_act" | \
grep -E "(Test:|Failures:)"
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
|
|
While I had thought this commit was a cherry-pick from upstream, it is
not. And so, this is not allowed here.
This reverts commit dfe5f16a33453b742a66cabc8ea9a52a33279810.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
CI: https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/23592
- some configs modification
|
|
https://source.denx.de/u-boot/custodians/u-boot-nand-flash
CI: https://source.denx.de/u-boot/custodians/u-boot-nand-flash/-/pipelines/23584
Remove device specific nand driver files as they are now replaced by a
common driver bcmbca_nand.c
Make use of OF_UPSTREAM which uses Linux dts.
Implement a minimal set of defconfig options to enable basic NAND
functionality. Tested on:
47622
63146
63158
63178
6813
Set parameter_page_big_endian to zero for bcmbca.
Update log level messages so that more critical messages can be logged
to console and help the troubleshooting with field devices.
|
|
Currently, the PCI subsystem selects the small "region 2" (which starts at 0x7000000)
as bus_addr/phys_addr. As a consequence, the BAR0 on PCIe video card cannot be initialized,
because it simply doesn't fit into 0x1000000 bytes size of "region 2".
U-Boot should use "region 1" instead (the one which starts at 0x60090000), because
it has much bigger size (0xFF70000), and easily accomodates BAR0 of the video card.
Linux kernel also uses 0x60090000 as bus_start/phys_start.
Signed-off-by: Yuri Zaporozhets <yuriz@vodafonemail.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
To restore MMC boot, enable SPL_SYS_MMCSD_RAW_MODE and recover
SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION.
Fixes: 2a00d73d081 ("spl: mmc: Try to clean up raw-mode options")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
With the move from script based booting to using bootmeth a lot of
environment variables have changed. To always use the default environment
it is recommendable to erase the environment stored in the SPI flash.
This can be done with the 'env erase' sub-command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
If BIOSEMU is compiled for RISC-V (SiFive Unmatched board) and the function
dm_pci_run_vga_bios() is executed, U-Boot stops with error message saying
that the SPL malloc pool is too small. So increase the default pool size
when both BIOSEMU and RISCV parameters are set.
Signed-off-by: Yuri Zaporozhets <yuriz@qrv-systems.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Update log level messages so that more critical messages can be logged
to console and help the troubleshooting with field devices.
This is a port of the upstream Linux patch to U-Boot.
https://lore.kernel.org/linux-mtd/20240223034758.13753-4-william.zhang@broadcom.com/
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
|
|
Set parameter_page_big_endian to zero for bcmbca
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
|
|
Make use of OF_UPSTREAM which uses Linux dts.
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
|
|
These device specific nand driver files can be removed because
they are now replaced by a common driver bcmbca_nand.c
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
|
|
Rsync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dfu
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/23572
- Fastboot:
- handle unknown partition type as "raw"
- USB gadget:
- Fix ci_udc gadget driver for Tegra 2 devices by not using USBADRA
|
|
CI: https://dev.azure.com/sr0718/u-boot/_build/results?buildId=379&view=results
- mvebu: Disable JFFS2 support for Kirkwood and Armada XP boards (Tony)
- kirkwood: Enable bootstd for Sheevaplug board (Tony)
- mvebu: Add Allied Telesis x250 board (Chris)
- mvebu: Updates for Allied Telesis boards (Chris)
|
|
The x250 and SE250 are series of 10G L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Enable IPV6 support for the x530 board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
The x530 board doesn't use EFI and our toolchains don't include gnutls
so disable the tool in the defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
As things have been moved to Kconfig there are a number of dead comments
left over in x530.h. Remove them.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Enable IPV6 support for the x240 board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
The x240 board doesn't use EFI and our toolchains don't include gnutls
so disable the tool in the defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Use standard boot instead of the distro boot scripts. Regenerate the
board defconfig now that some options are selected automatically.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Remove CFG_SYS_BAUDRATE_TABLE as there's no reason not to use the
defaults defined via config_fallbacks.h.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Enable bootstd for Sheevaplug board.
Remove JFFS2 support. See JFFS2 Vulnerability[1].
Enable LTO to keep board size within limit.
Move default envs to text-base environment
[1] https://lore.kernel.org/u-boot/20241114233005.GN3600562@bill-the-cat/T/#m2fc25da1d2c019bc3cd8676991fdd64b8a21aa9b
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
These boards don't use JFFS2 file system for booting so remove it.
Ref: https://lore.kernel.org/u-boot/20241114233005.GN3600562@bill-the-cat/T/#t
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Acked-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
In the older USB controllers like for example in ChipIdea controller
used by the Tegra 2 the "USBADRA: Device Address Advance" bitflag
does not exist, so the new device address set during SET_ADDRESS
can't be deferred by hardware, which causes the host to not recognize
the device and give an error.
Instead store it until ep completes to apply the change into the hw
register as Linux kernel does. This should fix regression on old and
and be compatible with newer controllers.
Inspired by: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=ef15e5490edc7edf808d3477ab32e0e320792f65
Signed-off-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20241126072956.64778-2-clamor95@gmail.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-usb
- Fix two issues with the asix88179 driver
|
|
Fix missed rename from SPI_ADVANCE to SPI_STACKED_PARALLEL. This fixes
an issue encountered while testing the Zynq-7000 QSPI parallel Flash
implementation.
Fixes: f896aa656774 ("mtd: spi-nor: Rename SPI_ADVANCE to SPI_STACKED_PARALLEL")
Reviewed-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Dominik Wernberger <dominik.wernberger@gmx.de>
|
|
- Support for Microchip USB5744 hub
|
|
u-boot was crashing in qemu as the modeled hardware enforced overly
strict memory reads.
While this code will work on existing hardware, fix to avoid future issues.
Fixes: 12770d0df0e8 ("ast2600: spl: Add boot mode detection")
Link: https://gitlab.com/qemu-project/qemu/-/issues/2636
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The compiler will ignore it anyway:
include/linux/mtd/mtd.h:342:15: warning: type qualifiers ignored on function return type [-Wignored-qualifiers]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The ASIX 88179A drops packets when receiving fragmented packets larger
than the MTU size due to an insufficient URB buffer size. This change
synchronizes the URB buffer size with the configuration used in the
Linux kernel, resolving the packet drop issue.
To reproduce the issue, set the following configuration:
CONFIG_IP_DEFRAG=y
CONFIG_TFTP_BLOCKSIZE=16352
Then, run the `tftp` command. It will fail with a timeout error:
U-Boot> tftp zero.bin
Using ax88179_eth device
TFTP from server 10.0.0.196; our IP address is 10.0.0.18
Filename 'zero.bin'
Load address: 0x10000000
Loading: T T T T T T T T T T T
Retry count exceeded; starting again
Signed-off-by: Khoa Hoang <admin@khoahoang.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
The ASIX AX88179A locks up when the ADVERTISE_NPAGE bit is set in the
MII_ADVERTISE register, suggesting that this feature may be broken or
unsupported on this chip. In the Linux kernel, this bit is not set,
and enabling it also causes the PHY to lock up and stay in a
link-down state.
Additionally, the AX88179 and AX88179A variants do not appear to
support the ADVERTISE_LPACK bit, as setting it consistently reads
back as 0.
This patch removes the ADVERTISE_NPAGE and ADVERTISE_LPACK bits from
the MII_ADVERTISE register configuration. It also resets the PHY
before modifying the MII_ADVERTISE register, then restarts
auto-negotiation, following the same flow used in the U-Boot asix.c
driver.
Signed-off-by: Khoa Hoang <admin@khoahoang.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
The .bind function is implemented to bind the correct
"half" of the hub that the driver wants to bind,
and returning -ENODEV for the other "half".
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Add i2c initialization hook and set usb5744 platform
data with function having required i2c initialization sequence.
Apart from the USB command attach, prevent the hub from suspend.
when the “USB Attach with SMBUS (0xAA56)” command is issued to the hub,
the hub is getting enumerated and then it puts in a suspend mode.
This causes the hub to NAK any SMBUS access made by the SMBUS Master
during this period and not able to see the hub's slave address while
running the "i2c probe" command.
Prevent the MCU from the putting the HUB in suspend mode through register
write. The BYPASS_UDC_SUSPEND bit (Bit 3) of the RuntimeFlags2 register at
address 0x411D controls this aspect of the hub. The BYPASS_UDC_SUSPEND
bit in register 0x411Dh must be set to ensure that the MCU is always
enabled and ready to respond to SMBus runtime commands. This register
needs to be written before the USB attach command is issued.
The byte sequence is as follows:
Slave addr: 0x2d 00 00 05 00 01 41 1D 08
Slave addr: 0x2d 99 37 00
Slave addr: 0x2d AA 56 00
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Add support for the Microchip USB5744 USB3.0 and USB2.0 Hub.
The usb5744 driver trigger hub reset signal after soft reset.
The usb5744 hub need to reset after the phy initialization,
which toggles the gpio.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Don't error out if there is no vdd regulator supply, as these are
optional properties.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
As part of the reset, sets the direction of the pin to output before
toggling the pin. Delay of millisecond is added in between low and
high to meet the setup and hold time requirement of the reset.
Update the usb2514 hub_data with the reset delay and power on
delay values.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Janne Grunau <j@jannau.net> says:
Starting with v2024.10 dev_iommu_dma_unmap calls during device removal
trigger a NULL pointer dereference in the Apple dart iommu driver. The
iommu device is removed before its user. The sparsely used DM_FLAG_VITAL
flag is intended to describe this dependency. Add it to the driver.
Adding this flag is unfortunately not enough since the boot routines
except the arm one simply remove all drivers. Add and use a new function
which calls
dm_remove_devioce_flags(DM_REMOVE_ACTIVE_ALL | DM_REMOVE_NON_VITAL);
dm_remove_devices_flags(DM_REMOVE_ACTIVE_ALL);
to ensure this order dependency is head consistently.
Link: https://lore.kernel.org/r/20241123-iommu_apple_dart_ordering-v2-0-cc2ade6dde97@jannau.net
|
|
This replaces dm_remove_devices_flags() calls in all boot
implementations to ensure non vital devices are consistently removed
first. All boot implementation except arch/arm/lib/bootm.c currently
just call dm_remove_devices_flags(DM_REMOVE_ACTIVE_ALL). This can result
in crashes when dependencies between devices exists. The driver model's
design document describes DM_FLAG_VITAL as "indicates that the device is
'vital' to the operation of other devices". Device removal at boot
should follow this.
Instead of adding dm_remove_devices_flags() with (DM_REMOVE_ACTIVE_ALL |
DM_REMOVE_NON_VITAL) everywhere add dm_remove_devices_active() which
does this.
Fixes a NULL pointer deref in the apple dart IOMMU driver during EFI
boot. The xhci-pci (driver which depends on the IOMMU to work) removes
its mapping on removal. This explodes when the IOMMU device was removed
first.
dm_remove_devices_flags() is kept since it is used for testing of
device_remove() calls in dm.
Signed-off-by: Janne Grunau <j@jannau.net>
|
|
Avoids NULL pointer dereferences in apple_dart_unmap when the iommu
device is removed before its user. U-boot's device model does not track
dependencies between devices.
Observed on a M1 Ultra Mac Studio with v2024.10.
Acked-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Janne Grunau <j@jannau.net>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
CI: https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/23529
- Documentation:
- Document wget syntax enhancements with lwIP network stack
- Move README.kconfig to HTML documentation
- Remove redundant README.TPL
- UEFI:
- Simplify efi_tcg2_hash_log_extend_event()
- Allow EFI_LOADER_BOUNCE_BUFFER on all architectures
- Correctly unmap and free memory on errors
- Other:
- Enable EFI_LOADER_BOUNCE_BUFFER on StarFive VisionFive 2
|
|
We never free and unmap the memory on errors and we never unmap it when
freeing it. The latter won't cause any problems even on sandbox, but for
consistency always use unmap_sysmem()
Fixes: commit 22f2c9ed9f53 ("efi: memory: use the lmb API's for allocating and freeing memory")
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
