| Age | Commit message (Collapse) | Author |
|---|
|
Add support for DesignWare SDHCI host controller on Alibaba TH1520 SoC
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
The imply statements should be sorted in the sequence
of appearance in .config.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
Get product ID and the other information from EEPROM, use them to select
the correct DTB.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
The prefix "SPL_" is not needed when using CONFIG_IS_ENABLED().
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fixes: 5ecf9b0b8a75 ("board: starfive: add StarFive VisionFive v2 board support")
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
Support multiple DTBs for JH7110 based boards, so they can
select the correct DT at runtime.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
So JH7110 based boards can select their own DT at runtime.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
As OF_UPSTREAM is implemented, these code are redundant.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
To support the other JH7110 based boards, add u-boot
device tree for them.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: H Bell <dmoo_dv@protonmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
To support JH7110 based boards besides v1.3B,
add a common dtsi and add common code to it.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
There are difference between upstream DT and the old DT
in terms of reg base, reset gpio and syscon. Make the driver
compatible with upstream DT.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
Make the U-Boot JH7110 MMC driver compatible with upstream DT.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
Add u-boot features to the U-Boot device tree.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
Enable OF_UPSTREAM to use upstream DT and add starfive/ prefix to
the DEFAULT_DEVICE_TREE. Rename jh7110-starfive-visionfive-2-u-boot.dtsi
to jh7110-starfive-visionfive-2-v1.3b-u-boot.dtsi and set the v1.3b
device tree as the default device tree.
Drop redundant DT files from arch/riscv/dts/ and redundant clock and
reset definitions from include/dt-bindings/.
Since the old clock definitions is a little different from those in
upstream Linux, update the clock definitions in clock drivers
accordingly.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
|
|
The LicheeRV Nano is a small SBC using the Sophgo SG2002 RISCV SoC.
Signed-off-by: Thomas Bonnefille <thomas.bonnefille@bootlin.com>
|
|
Import a slightly modified version of the LicheeRV Nano and SG2002
device trees from the Linux Kernel. The current supported IPs are UART,
MMC, Timer, PLIC and CLINT.
Signed-off-by: Thomas Bonnefille <thomas.bonnefille@bootlin.com>
|
|
Provide a page describing the usage of U-Boot on the LicheeRV Nano and a
description of the board.
Signed-off-by: Thomas Bonnefille <thomas.bonnefille@bootlin.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
include display_options.h to address build warning:
lib/smbios.c: In function ‘smbios_update_version’:
lib/smbios.c:305:9: warning: implicit declaration of function ‘print_buffer’
[-Wimplicit-function-declaration]
print_buffer((ulong)ptr, ptr, 1, old_len + 1, 0);
^~~~~~~~~~~~
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Fix spelling mistake in the board init files of j721e and j721s2.
s/WKUP_DEVSTAT_MCU_OMLY_MASK/WKUP_DEVSTAT_MCU_ONLY_MASK
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
|
|
In the x86emuOp_jump_call_near_IMM() function the target address is
printed incorrectly when jumping backwards. For example instead of
"jmp 0xe8bc" the string "jmp ffffe8bc" is printed. That's because
of the following macro:
DECODE_PRINTF2("%04x\n", ip);
while it should be
DECODE_PRINTF2("%04x\n", (u16)ip);
Signed-off-by: Yuri Zaporozhets <yuriz@qrv-systems.net>
|
|
In the x86emuOp_call_near_IMM() function the address of CALL is
printed incorrectly when jumping backwards. For example, the correct
disassemble of the bytes below would be:
0000E8DE E8DBFF call 0xe8bc
(verified by ndisasm). But instead the address is printed as "ffffe8bc".
That's because of the following macro:
DECODE_PRINTF2("%04x\n", ip);
while it should be
DECODE_PRINTF2("%04x\n", (u16)ip);
Signed-off-by: Yuri Zaporozhets <yuriz@qrv-systems.net>
|
|
When DEBUG_DECODE_F is enabled in bios_emulator, the printing of
SET{O,NO,B,NB,Z,NZ,BE,NBE,S,NS,P,TP,L,NL,LE,NLE} instructions
is not followed by newline and is, therefore, immediately followed
by the printed address of a new instruction. This garbles the output
and makes it very difficult to read.
This patch adds missing DECODE_PRINTF("\n") calls to print newlines.
Signed-off-by: Yuri Zaporozhets <yuriz@qrv-systems.net>
|
|
When DEBUG_DECODE_F is enabled in bios_emulator, the printing of BSF
instructions is garbled because the '\n' symbol is used instead of
the correct '\t'. Fix that.
Signed-off-by: Yuri Zaporozhets <yuriz@qrv-systems.net>
|
|
Anurag Dutta <a-dutta@ti.com> says:
Hi All,
In u-boot, hbmc is broken and has been removed from j7200
configs. This series re-enables the hbmc driver and introduces a series
of hyperflash boot fixes. At present, in u-boot, the parent device (fss)
gets registered as a syscon device. This is done because the MMIO
mux driver in u-boot did not support the mux functionality when the
parent device is not a syscon. In this series, we make relevant changes
in the hbmc driver as well as dts' so that we can use the reg-mux driver for
selecting the appropriate state of the mux.
Test logs:
1) j721e-idk-gw hyperflash boot test: https://gist.github.com/anuragdutta731/50aae6fec707a3ffad6d985de6757fe4
2) j7200-evm hyperflash boot test: https://gist.github.com/anuragdutta731/c3a4d60f8bfd9c425d6c44b36eb7322b
Link: https://lore.kernel.org/r/20241129113136.383277-1-a-dutta@ti.com
|
|
The HBMC_AM654 driver was dependent on SYSCON because syscon APIs were
being used to select the multiplexer state. Change the dependency to
MULTIPLEXER and MUX_MMIO because mux APIs are now being used to
select mux state.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Kernel commit dbb124cf6888 ("configs: j7200: Remove HBMC_AM654
config") removed the HBMC_AM654 config because hbmc was broken
in u-boot. Hence, add the missing configs necessary to re-enable
Hyperflash boot.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
HyperFlash
The size of J7200 tiboot3.bin is 516KB but the memory reserved for it in
HyperFlash was 512KB. This led to overlap of tiboot3.bin over tispl.bin
region and break in HyperFlash boot mode.
Therefore, fix this by increasing the memory allocated for tiboot3.bin
to 1MB for J7200.
Fixes: cf1d6867f774 ("board: ti: j7200: Introduce support for j7200 build targets")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Kernel commit 5b2671594b80 ("configs: j721e: Remove HBMC_AM654
config") removed the HBMC_AM654 config because hbmc was broken
in u-boot. Hence, add the missing configs necessary to re-enable
Hyperflash boot.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Add 32-bit address overrides for Hyper Bus Memory Controller
for Hyperflash to be functional in R5 SPL.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Add 32-bit address overrides for Hyper Bus Memory Controller
for Hyperflash to be functional in R5 SPL.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
The syscon APIs were used for selecting the state of the mux
device because the mmio-mux driver in u-boot did not support
the mux functionality when the parent device is not a syscon.
Change to mux APIs which utilizes the reg-mux driver to select the
state of the multiplexer.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Add config required to build mmio-mux driver and dependencies.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
|
|
Neha Malcom Francis <n-francis@ti.com> says:
Enable the NFS command across all platforms to allow network booting via
the NFS. Clean up the J7 configs to use TI_COMMON_CMD_OPTIONS.
Link: https://lore.kernel.org/r/20241129110333.444270-1-n-francis@ti.com
|
|
Instead of bloating the defconfig with CONFIG_CMD_*, move J7 devices to
start using TI_COMMON_CMD_OPTIONS.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
|
|
Add CMD_NFS to list of configs implied by CONFIG_TI_COMMON_CMD_OPTIONS.
This allows network booting via the NFS protocol from the U-Boot prompt.
Fixes: 10de12570799 ("disable NFS support by default")
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
|
|
Gokul Praveen <g-praveen@ti.com> says:
The OMAP specific UART driver is changed from a generic implementation of
certain ops functions to an OMAP specific implementation of it to add
support for higher baudrates for OMAP devices.
Hence to support the above change, static functionality of ops functions
in generic ns16550 UART U-Boot driver is removed and also migrated certain
macros to its header file for usage in device-specific drivers.
Boot logs link :
https://gist.github.com/GOKU-THUG/8b90117c963e5da5c1b6caeee427c82c
Link: https://lore.kernel.org/r/20241126105131.43359-1-g-praveen@ti.com
|
|
higher baudrates
Move to OMAP specific implementation of certain ops functions as the UART
prints on the serial console fail for baudrates greater than 460800.
The MDR1 register is responsible for determining the speed mode at which
the UART should operate for OMAP specific devices. The baud divisor is used
to set the UART_DLL register which is used for generation of the baud
clock in the baud rate generator. The implementation logic is similar to
how it is implemented in omap_8250_get_divisor function of 8250_omap UART
linux driver.
Signed-off-by: Gokul Praveen <g-praveen@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Increase scope of ops functions and do some clean up for usage in device
-specific UART drivers.
Remove the static functionality of ops functions and migrate certain macros
to header file for usage in device-specific drivers.
Signed-off-by: Gokul Praveen <g-praveen@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Garrett Giordano <ggiordano@phytec.com> says:
This patch set adds the phyCORE AM62Ax board support and documenation to
u-boot.
The phyCORE-AM62Ax is a SoM (System on Module) featuring TI's AM62Ax SoC. It can
be used in combination with different carrier boards. This module can come
with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs
from the AM62x family.
A development Kit, called phyBOARD-Lyra is used as a carrier board reference
design around the AM62x SoM.
This series depends on the following two patches:
- [PATCH v2] arm: mach-k3: am62a7: Provide a way to obtain boot device for non SPL
https://lists.denx.de/pipermail/u-boot/2024-October/570156.html
- [PATCH] board: phytec: common: Introduce CONFIG_PHYTEC_K3_DDR_PATCH
https://lists.denx.de/pipermail/u-boot/2024-November/571543.html
Link: https://lore.kernel.org/r/20241118231606.3161665-1-ggiordano@phytec.com
[trini: Fix warning in board/phytec/common/k3/board.c when
CONFIG_EFI_HAVE_CAPSULE_SUPPORT is not enabled]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Introduce get_boot_device() to obtain the booting device. Make it also
available for non SPL builds so u-boot can also know the device it
is booting from.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
|
|
The module pid4 currently corresponds to the index of the toradex_module
array. If a new pid4 is introduced that does not follow the sequence of
the previous entries, it will create a gap in the array.
To address this, embed pid4 within the toradex_som structure and
implement a function to retrieve the index corresponding to pid4.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
Add documentation for PHYTEC phyCORE-AM62ax SoM.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
|
|
Add support for PHYTEC phyCORE-AM62A7 SoM.
Supported features:
- 2GB LPDDR4 RAM
- eMMC
- External SD
- Ethernet
- debug UART
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
|
|
Wadim Egorov <w.egorov@phytec.de> says:
This implements capsule updates for all our K3 SoMs for
eMMC, OSPI NOR and uSD cards.
We can use capsule updates to update the bootloader on all our
supported flash devices.
Link: https://lore.kernel.org/r/20241127121736.1525948-1-w.egorov@phytec.de
|
|
Enable raw & on disk capsule updates and provide configs required
for updating MTD devices. Also resync after savedefconfig.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Implement EFI capsule update functionality for PHYTEC K3-based SoMs.
These SoMs feature various flash device options, including eMMC,
OSPI NOR, and uSD card at the board level.
This update provides the necessary logic to enable EFI capsule updates
across all three flash devices, ensuring flexible and robust firmware
upgrade capabilities.
The GUID is dynamically generated for the board, to get it:
efidebug capsule esrt
========================================
ESRT: fw_resource_count=3
ESRT: fw_resource_count_max=3
ESRT: fw_resource_version=1
[entry 0]==============================
ESRT: fw_class=C7D64D6D-10B2-54BC-A3BF-06A9DC3653D9
ESRT: fw_type=unknown
ESRT: fw_version=0
ESRT: lowest_supported_fw_version=0
ESRT: capsule_flags=0
ESRT: last_attempt_version=0
ESRT: last_attempt_status=success
[entry 1]==============================
ESRT: fw_class=09841C3F-F177-5D57-B1F6-754D92879205
ESRT: fw_type=unknown
ESRT: fw_version=0
ESRT: lowest_supported_fw_version=0
ESRT: capsule_flags=0
ESRT: last_attempt_version=0
ESRT: last_attempt_status=success
[entry 2]==============================
ESRT: fw_class=D11A9016-515E-503A-8872-3FF65384D0C4
ESRT: fw_type=unknown
ESRT: fw_version=0
ESRT: lowest_supported_fw_version=0
ESRT: capsule_flags=0
ESRT: last_attempt_version=0
ESRT: last_attempt_status=success
========================================
On the board (from uSD card containing capsule binaries at boot):
load mmc 1:1 $loadaddr tiboot3-capsule.bin
efidebug capsule update $loadaddr
load mmc 1:1 $loadaddr tispl-capsule.bin
efidebug capsule update $loadaddr
load mmc 1:1 $loadaddr uboot-capsule.bin
efidebug capsule update $loadaddr
The binaries will be flashed to the flash device you are booted from.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Fill in phycore-am64x capsule GUID properties of the base
binman capsule nodes.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Fill in phycore-am62x capsule GUID properties of the base
binman capsule nodes.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
|
|
Siddharth Vadapalli <s-vadapalli@ti.com> says:
Hello,
This series adds support for USB DFU boot on TI's AM62A SoC which has
two instances of DWC3 USB Controllers namely USB0 and USB1. The USB0
instance of the USB Controller supports USB DFU boot:
ROM => tiboot3.bin => tispl.bin => u-boot.img
USB DFU Boot requires the USB Controller to be configured for Gadget
mode of operation. Since the USB0 instance of the DWC3 USB Controller
supports both Host and Gadget modes of operation via the Type-C interface
on the AM62A7-SK board, the device-tree specifies the "dr_mode" as "OTG".
However, there is currently no support for dynamically switching the "mode"
from Host to Gadget and vice-versa with the help of a state-machine.
The OTG mode is treated as a separate mode in itself rather than being
treated as an intermediate stage before assuming the Host/Gadget mode.
Due to this, USB DFU boot via the Type-C interface doesn't work as the
USB Controller hasn't been appropriately configured for Device/Gadget
mode of operation. One option is to change the device-tree to specify
"dr_mode" as "peripheral" and force the controller to assume the Device
role. This will imply that the U-Boot device-tree for AM62A diverges
from its Linux counterpart. Therefore, with the intent of keeping the
device-tree uniform across Linux and U-Boot, and at the same time, in
order to enable USB DFU boot in "OTG" mode with the DWC3 Controller,
the first patch in this series sets the "mode" on the basis of the
caller function, rather than using the "dr_mode" property in the
device-tree. There are only two callers of "dwc3_generic_probe()",
each of which clearly specify the expected mode of configuration.
This will enable both Host and Device mode of operation based on the
command executed by the user, thereby truly supporting "OTG"
functionality when the USB Controller supports it.
The second patch in this series adds USB DFU environment for AM62A,
enabling USB DFU Boot and USB DFU flash on AM62A.
In addition to the patches in this series, the following device-tree
changes will be required to test USB DFU on AM62A (bootph-all property
to be added to ensure that USB Controller is present at all stages
for DFU Boot):
https://gist.github.com/Siddharth-Vadapalli-at-TI/53ba02cb0ff4a09c47e920d08247065f
The above device-tree changes will be made to the Linux device-tree,
which shall ensure that the same shall be a part of U-Boot device-tree
eventually.
The USB DFU config fragments for AM62x have been used for enabling
USB DFU boot on AM62a as follows:
R5 => am62ax_evm_r5_defconfig + am62x_r5_usbdfu.config
A53 => am62ax_evm_a53_defconfig + am62x_a53_usbdfu.config
Logs validating USB DFU boot with this series:
https://gist.github.com/Siddharth-Vadapalli-at-TI/daa71da1b0e478a51afea42605fb2d2c
Link: https://lore.kernel.org/r/20241126120322.1760862-1-s-vadapalli@ti.com
|
|
Include the TI K3 DFU environment to support DFU Boot and DFU Flash.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
|
|
There are only two callers of "dwc3_generic_probe()", namely:
1. dwc3_generic_peripheral_probe()
2. dwc3_generic_host_probe()
Currently, the "mode" is set based on the device-tree node of the
platform device. Also, the DWC3 core doesn't support updating the "mode"
dynamically at runtime if it is set to "OTG", i.e. "OTG" is treated as a
separate mode in itself, rather than being treated as a mode which should
eventually lead to "host"/"peripheral".
Given that the callers of "dwc3_generic_probe()" clarify the expected
"mode" of the USB Controller, use that "mode" instead of the one
specified in the device-tree. This shall allow the USB Controller to
function both as a "Host" and as a "Peripheral" when the "mode" is "otg"
in the device-tree, based on the caller of "dwc3_generic_probe()".
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
|
